Operating Instructions AC/Rechargeable Professional
Contents
1. 2010 06 02 20 00 022. a Q BE Ref No IM B102 01 Panasonic Operating Instructions AC Rechargeable Professional Hair Clipper Model No ER1411 Before operating this unit please read these instructions completely and save them for future use o o ER1411_AUS_JABARA indd 1 2010 06 02 20 00 01 g Thank you for choosing a Panasonic Hair Clipper Please read all instructions before use E Important gt Before use This clipper is designed for professional use to trim hair and beards Charge it for 8 hours before use for the first time in order to activate the built in rechargeable batteries It can be operated on either an AC adaptor or rechargeable batteries Read all instructions carefully before use gt Charging the clipper e Do not use any power cord or AC adaptor other than this AC adaptor RE9 41 e Avoid charging the batteries at temperatures below 5 C or above 35 C e Avoid charging the batteries in direct sunlight or near a radiating heat source e The charge status lamp may blink at an early stage when it is used for the first time or if it has not been used for 6 or more months even if it is fully charged This is not a malfunction e Even though the clipper may not be used for an extended period charge every 6 months to preserve battery life e The power cord cannot be replaced If it is damaged the AC adaptor should be discarded EN gt Using the clipper e This clipper has a built in
3. ith moving parts e Do not wrap the appliance by the cord as it may become detached causing damage or injury e If the clipper is not working properly have it inspected at an authorized service center Specifications Power source See the name plate on the product Automatic voltage conversion Motor voltage 2 4 V DC Charging time 1 hour p Parts identification Main body 3 mm 6 mm comb attachment Power switch 0 CHARGE 1 Charge status lamp Appliance socket Blade 4 Mounting hook Cleaning lever Moving blade Stationary blade ER1411_AUS_JABARA indd 3 9 mm 12 mm comb attachment 15 mm 18 mm comb attachment AC adaptor RE9 41 Power cord Appliance plug Cleaning brush Oil 2010 06 02 20 00 02 s e ey Charging the hair clipper Slide the power switch to 0 CHARGE Plug in the AC adaptor into a E household outlet y Insert the appliance plug into the clipper O N e Charge status lamp glows in red and charging starts e Charging is completed when Charge status lamp blinks in red once every second Max 1 hour later e 10 minutes after charging is completed the charge status lamp blinks in red once every 2 seconds e 1 full charge will provide approximately 80 minutes of continuous j operation D gt AC operation If you connect the AC adaptor to the clipper in the same wa
4. rechargeable battery Do not throw into fire apply heat or charge use or leave in a high temperature environment e Warning Keep the appliance dry e The clipper may become warm during operation and or charging This is normal e Check that the blades and the attachments are not damaged before use Replace them if they are damaged e Before each use apply oil at the places marked with arrows See page 6 e You should not allow permanent wave lotion hair restorer or hair spray to come into contact with the main body or the blades Doing so may result in cracking discoloring or corrosion e You should not drop the clipper on the floor e You should not knock the blades and the attachments against hard objects e You should not trim the hair of a pet gt Cleaning the clipper e Clean the housing using only a cloth slightly dampened with water or a mild soap solution e Never use a caustic solution e Never submerge the clipper in water 2 ER1411_AUS_JABARA indd 2 2010 06 02 20 00 01 gt Storing the clipper e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance e Never tamper w
5. the moving blade while cy pressing down on the cy cleaning lever to raise the moving blade I Lubrication 1 Apply a few drops of the oil to the space between the stationary blade and moving blade e Apply the oil to the clipper before and after each use 2 Remount the blade on the clipper ER1411_AUS_JABARA indd 6 2010 06 02 20 00 02 W Removing the built in rechargeable batteries Remove the batteries as illustrated e Disconnect the clipper from a household outlet e Fully discharge the batteries e Be careful not to short circuit the batteries WARNING Do not attempt to replace the batteries for the purpose of reusing the clipper This could result in the risk of fire or electric shock Important notice regarding environmental protection The built in rechargeable Nickel Metal Hydride batteries contain substances that may be environmentally harmful Please remove the batteries before discarding your clipper am AZ For environmental protection and recycling materials This clipper contains Nickel Metal Hydride batteries Please make sure that the batteries are disposed of at an officially assigned location if there is one in your country ER1411_AUS_JABARA indd 7 2010 06 02 20 00 02 Panasonic Electric Works Wanbao Guangzhou Co Ltd http panasonic net Printed in China EN 0000000000 X0000 0 ER1411_AUS_JABARA indd 8
6. y as for charging and turn on the power you can use it even if the battery capacity is low e If the clipper does not operate charge the clipper for approximately 1 minute e Be careful not to discharge the battery completely with the power left turned on It results in shortening the battery life ER1411_AUS_JABARA indd 4 2010 06 02 20 00 02 gt Using the comb attachments 1 Select the trimming heights indicated on the insides and sides of the attachments 2 Mount the attachment to the clipper as illustrated The actual cut length may be longer than the set length ANY nt N Y JY Removing the attachment from the clipper Slide one side of the attachment off the mounting in direction indicated with the arrow I Removing and mounting the blade gt Removing the blade 1 Hold the clipper with the power switch facing upward and push the blade with your thumb while catching the blade in your other hand e Be sure to turn off the power before you remove the blade ER1411_AUS_JABARA indd 5 2010 06 02 20 00 02 gt Mounting the blade 1 Fit the mounting hook into the blade mounting on the clipper and push in until it clicks I cleaning the blade 1 Brush off any 2 Remove the blade 3 Brush the hairs out hairs from the and brush off the from between the clipper and from hairs from the stationary blade and around the blade blade edge
Download Pdf Manuals
Related Search