Home

Hydrostatic Tool Carrier 5900 Taifun Operating Instructions

1. After every 100 operating hours or at least once a year before season starts remove fan case to clean cooling fins on cylinder and cylinder head as well as guiding plates serving for smooth air circulation cooling air screen and oil cooler Lol see operating instructions for Lombardini engine Jagria Service6 Exhaust System Constantly check exhaust system C 5 for plant trash and clean if necessary Otherwise danger of fire Check each time before you take up operation 50 agria Hydrostatic Tool Carrier 5900 Taifun 5 Maintenance agria Diesel Engine 51 3 25 100 Air filter Cyclone Air filter D 9 O Every time you take up operation discharge the air preliminary filter by squeezing the dust extraction valve oO Z2 E hours through careful tapping at one end Wash and Y e Clean air filter insert B always after 25 operating dry the filter cover A Do not use compressed air to blow out dust of filter insert and do not treat with oil e Change air filter insert B after tapping out 3x and at the latest after every 100 operating hours or when damaged Never run the engine without the air filter as this leads to increased engine wear Charging Battery ve u Remove the battery from the vehicle beginning by Petrol and diesel disconnecting from the negative terminal engine Ensure that there is good ventilation in the room Only use suitable DC charging units Connect
2. y Instructions aq ria of the original operating instructions Plydrostatic Tool Carrier 5900 Taifun 5900 241 251 253 521 e 2 cylinder B amp S Vanguard 18 HP 22 HP e 2 cylinder Diesel 25LD425 Electric Starter Version 5883 5969 MM Before commissioning the machine read operating A instructions and observe warnings and safety instructions Operating Instructions No 998 781 C 08 10 Symbols Name Plate Please complete For name plate refer to page 3 fig A 4 For engine type and number refer to page 72 fig C 4 petrol engine to page 76 fig D 15 diesel engine Please state these data when ordering spare parts to avoid wrong deliveries Only use original agria spare parts Specifications figures and dimensions stated in these instructions are not binding No claims can be derived from them We reserve the right for improvements without changing these instructions This delivery comprises e Operating instructions O Tool carrier lool kit gt agriga Service contact Your agria workshop LO see separate engine operating instructions aqria Symbols Warning danger Important information Fuel Choke Engine Start Engine Stop Battery charge indicator Clutch Forward Reverse Fast Slow Hydraulic system PTO Brake Parking brake Closed locked Open unlocked Clockwise Anti clockwise Lifting point fixing point for recovery t
3. A Do not fasten safety circuit lever The safety circuit lever also serves to shut off the engine in an emergency situation Release the safety circuit lever for fast engine shut off The lever automatically goes to STOP position 22 agria Hydrostatic Tool Carrier 5900 Taifun 3 Devices and Operating Elements aqria Clutch The tool carrier is equipped with a single disc dry clutch which is operated via the clutch lever B 5 With clutch lever pulled up to position O the clutch is decoupled i e the engine stops dri ving the machine Watch for the correct clutch play to avoid clutch slipping away during operation Do not park the machine with the clutch pulled and the engine running This may damage the clutch release bearing Ensure the lever is pulled pawl locked in pla ce when you park the machine with the engi ne stopped otherwise clutch problems may result due to corrosion PTO Shaft Connection The speed independent PTO A 22 is connec ted with a connection mechanism B 7 With the connection mechanism drawn backwards the PTO drive is connected when slid for wards the PTO drive is disconnected agria Hydrostatic Tool Carrier 5900 Taifun 23 3 Devices and Operating Elements agria Transmission The agria tool carrier is equipped with a hydrostatic drive Setting the Driving Speed and Direction Lever shift model e The driving speed forward or reverse is stepless
4. 28 aqria Wheel Attachment Bolts Version A wheel bolt with spring lock washer Version B locking bolt with spring lock washer and wheel nut Screw short thread end of locking bolt tightly into hub if possible glue with LOCTITE 270 or similar glue Fit countersunk side of spring lock was her onto disk wheel On a new machine or after wheel change re tighten wheel bolts and nuts after the first 2 operating hours with 100 Nm Re tighten bolts and nuts in each maintenance Snow Chains When working with snow chains fitted on wheels observe manufacturer s instructions make sure there is sufficient clearance between chains and machine parts Wheel Track Adjustment System Item 5519 031 used to fit terra tyre drive wheels 21 x 11 00 8 TG Drive Wheels for slopes It is recommended to use twin OI wheels or traction cage wheels for mowing areas on extremely steep slopes agria Hydrostatic Tool Carrier 5900 Taifun 3 Devices and Operating Elements agria Hood Remove Hood o Lift rear end of hood e Lift front end of hood and completely remove it Placing Hood eo Place front and rear of hood with the rubber cups onto the ball heads e By slightly applying pressure to the rear and front of the engine cowling have the ball cups engage in the ball heads Axle Adjustment To improve the weight distribution with heavy implements the axle can be displaced forwards e For that purpos
5. Do not spill any fuel use a proper filling device Do not cause fuel tank to overflow but leave a 5 mm margin for the fuel to expand e Check transmission oil level wm 52 Note For reasons of transport the engine is not filled completey with engine oil Before you operate the engine the first time fill in engine oil diesel 2 2 agria Hydrostatic Tool Carrier 5900 Taifun 35 4 Commissioning and Operation g p Petrol Engine agria Before starting the engine O Mount both spark plug connectors Sufficient fuel is filled into the tank Air filter clean Er 27 O Check the engine oil level ma 481 ocer O O Check transmission oil level 52 O Check all bolts and nuts for tight fit 55 Only take machine into operation with A all protective devices mounted and positioned to provide protection Careful when starting the engine in closed rooms Ensure good ventilation and fast escape of exhaust fumes Exhaust fumes contain carbon monoxide which acts toxic when inhaled Do not touch the hot engine danger of burns A Do not touch or remove the ignition line and spark plug connector while the engine is running 36 agria Hydrostatic Tool Carrier 5900 Taifun 4 Commissioning and Operation g p Petrol Engine agria Starting Petrol Engine O Open both fuel taps C 13 Cold engine put CHOKE lever to CHOKE position C 20 Warm eng
6. N max 20 seconds As soon as the engine starts let go ignition key it automatically moves back into position T When the engine is running the red indicator lamps must be extinguished Only the green OK indicator lamp may continue to be lit up If the engine does not start and re start is necessary turn key back to position 0 to repeat start re start lock e Letthe engine warm up for some time e f the engine does not start repeat the starting procedure in the same order after a break of 1 minute If the engine does not start after 2 attempts at starting look for the cause in the breakdown table 40 agria Hydrostatic Tool Carrier 5900 Taifun 4 Commissioning and Operation e p Diesel Engine QT Shutting off Diesel Engine also see operating instructions for Lol Lombardini engine O Before you shut off the engine let it run at increased idling speed for 1 minute to cool down and to avold carbon to deposit on the injection valve This ensures continued and reliable operation Turn key back to position 0 Secure tool carrier against unauthorized use remove ignition key agria Hydrostatic Tool Carrier 5900 Taifun 41 4 Commissioning and Operation agria Operating the Machine Check safety circuit function A only operate the machine if the safety circuit is working O Start the engine as specified in chapter Starting the Engine Wear individual prote
7. beyond the dead centre The eccentric lever automatically comes to a stop both drive wheels are blocked To release parking brake swivel eccentric lever back to original position brake Is released Do not drive and brake at the same time O Prior to starting driving absolutely disengage brake as otherwise risk of damage due to overpressure failure of wheel motors Steering Handle Do never adjust operating handles during A working risk of accidents Steering Handle Height Adjustment e Unfix clamping levers A on either side until the detents are free e Bring left and right steering handle to the desired height and introduce into the respective detent e Tighten clamping levers A again Steering Handle Lateral Adjustment From its normal position centre position the steering handle can be turned by about 30 to the left or r ight Pull ball handle B 1 upwards and keep it in position then turn steering handle to the left or right into the desired position O Release ball handle and slightly move steering hand le to the left and right until the fixing bolt is engaged 26 agria Hydrostatic Tool Carrier 5900 Taifun 3 Devices and Operating Elements agria Loading Belt For loading the machine and for suspending the retaining rope for works on slopes the loading belt A 7 is provided To that end remove hood Check loading belt for damage replace it if necessary Do not use
8. engine Check regularly and if necessary replace all protecting devices and tools subject to wear and tear Replace damaged cutting tools Always wear safety gloves and use pro per tools when exchanging cutting tools Do not carry out repairs like welding grinding drilling etc on structural and safety relevant parts e g hitch aqria Keep tool carrier and implement clean to avoid risk of fire Check nuts and bolts regularly for tight fit and re tighten if necessary Ensure that you re install all safety and protective devices and adjust them properly after maintenance and cleaning Only use original agria spare parts All other commercial spare parts must correspond to quality and technical requirements specified by agria Storage It is not allowed to store the tool carrier in rooms with open heating Never park the tool carrier in closed rooms with fuel left in tank Fuel vapours are hazardous Engine Fuel and Oil Never let the engine run in closed rooms Extreme danger of intoxication For the same reason also replace damaged exhaust pipe immediately Be careful when handling fuel Great danger of fire Never refill fuel close to open fire inflammable sparks or hot engine parts Do not refill fuel in closed rooms Do not smoke when refilling Refill only with the engine shut off and cooled down agria Hydrostatic Tool Carrier 5900 Taifun 11 1 Safety Instructions Do not sp
9. filler tube max Changing Engine Oil The first oil change is after 8 operating hours Following oil changes are every 50 operating hours Change oil while engine is still warm but not hot danger of burns Clean oil filler tube C 2 drain plug and surrounding parts e Change the oil and dispose of properly O Tighten cap und drain plug For engine oil quality refer to Specifications 44 agria Hydrostatic Tool Carrier 5900 Taifun 5 Maintenance Petrol Engine agmnia Changing Engine Oil Filter The oil filter C 8 must be changed after100 hours of operation or after each season whichever comes first Before a new filter is installed the filter seal must receive a light coat of fresh clean motor oil Screw the filter on by hand until the seal touches the oil filter adapter Then tighten further about 1 2 to 3 4 turn Start the motor and allow to run at IDLE in order to check whether the seal is tight Shut off the motor check the oil level and add oil if necessary agria Hydrostatic Tool Carrier 5900 Taifun 45 5 Maintenance Petrol Engine agmnid Standard Air Filter Clean preliminary air filter V always after a maximum of 25 operating hours or in case of heavy dust occurence even after few hours e Clean air filter cartidge P always after a maximum of 100 operating hours or in case of heavy dust occurence even after few hours e Replace the preliminary filter an
10. 108 EC 2000 14 EC 2004 108 EG 2000 14 EG folgenden EG Richtlinien 2004 108 CE 2000 14 CE 2004 108 EG 2000 14 EG Folgende harmonisierte Les normes harmonis es Following harmonized De volgende Normen oder Teile davon ou extraits de celles ci ou standards or parts of it or geharmoniseerde normen oder techn Spezifikatio les sp cifications technical specifications of delen ervan of nen wurden angewendet techniques suivantes ont have been applied technische specificaties t appliqu es werden toegepast EN 12733 2001 A1 2009 M ckm hl den 15 02 2010 Siegfried Arndt Rudolf Tigge Gesch ftsf hrer Leiter Entwicklung amp Konstruktion Directeur Responsable d veloppement et tudes Managing Director Head Research and Development Bedrijfsleider Hoofd ontwikkeling en constructie Herr Tigges ist bevollm chtigt die technischen Unterlagen zusammenzustellen Monsieur Tigges est habilit a agencer la documentation technique Mr Tigges is authorized to assort the technical documents De heer Tigges is gemachtigd om de technische documentatie op te stellen Anschrift adresse address adres agria Werke GmbH Bittelbronner Str 42 D 74219 M ckm hl agria Hydrostatic Tool Carrier 5900 Taifun 77 agria Werke GmbH Bittelbronner StraBe 42 D 74219 M ckm hl Tel 49 0 6298 39 0 Fax 49 0 6298 39 111 e mail info agria de Internet www agria de Your local agria specialist dealer
11. Fan air cooled ldling speed 1400 rpm 2 cylinder 4 stroke Engine oll OHV engine petrol Filling quantity approx 1 6 Bora 75 5 mm Multi grade oil GEN 70 mm at ambient temperature 15 to 45 TC Cubic capacity 627 com SAE 10W 40 API SE SF or higher Output 16 4 kW 22 hp at ambient temperature 25 to 15 C at 3600 rpm SAE 5W 20 API SE SF or higher Max torque 46 3 Nm at 2700 rpm Spark plug Bosch FR8DC CHAMPION RC 12YC Spark plug gap 0 76 mm Ignition Electr magnetic ignition contactless Alf OAD E 0 2 0 3 mm Radio remote screened as per VDE 0879 Valve clearance engine cold Intake and outlet 0 1 0 15 mm Te CA Recoil starter Electrical starter 12V DOMO Va 12V 20Ah Generator 12V 192 W FU PA Commercial petrol min octane number 85 RON refer to fuel recommendations Fuel tank capacity abt 7 51 Fuel consumption 312 g kWh Fuel filter feul online Air filter Dry filter element with foamed preliminary filter version 5900 251 cyclone filter Carburetor Horizontal float carburetor 18 Lubrication system Oil circulation lubrication Oil pressure in the dle run min 0 35 bar ON TIER dia Filter cartridge Noise level e In acco
12. any loading devices with sharp edges e g sharp edged hooks lugs etc Never walk or remain under moving loads Dan ger Fixing Points For towing away recovering and tying down and to ensure a safe transport use the fixing Points GO at the connection flange and engine food guard Drive Wheels For full tractive power mount wheels with pointed parts of lugs showing in driving direction wheels seen from above Fit the countersunk side of spring lock washer into countersink type holes of disk wheel see fig Wheel Attachment Bolts p28 The wheels can also be mounted either on their inner or outer sides for variable track widths narrow track wide track refer to track widths table p15 I vrreftread Profile Jus Jee LA ES D E mens general maintenace forso 112 am sooralieaiyre generatmaitenace 2490 41 be As ARI ba BP d 20x8 00 10 grass tyre grass maintenance 3490 511 Ui M d E 23x8 50 12 wide track held tyre 5990 611 Sn 1x11 00 8 terra tyre general maintenace 3490 611 23x10 50 12 wide track field tyre 5990 711 agria Hydrostatic Tool Carrier 5900 Taifun 27 3 Devices and Operating Elements To avoid damage to the brake 3 system e Spring washer with ball shaped side absolutely required e Only use screw of original length 5519 031 Ball spring washer Wheel bolt Track width adjuster item 5519 031 Ball spring washer Wheel bolt
13. at the base machine For dismounting proceed in reverse order agria Hydrostatic Tool Carrier 5900 Taifun 31 3 Devices and Operating Elements gt Petrol Endine alt Bes Version AGFID Baitery There is no dry pre charging of batteries on the new machines or trailers Therefore the battery must be filled with accumulator acid and charged charging current 1 10 of battery capacity see supplement of battery manufacturer Starter Switch The ignition start switch 33 for electric starter has 3 settings O Il Charging current off key removable Il Operation Ol Start position ignition key automatically goes into operating position I Warning Signal The warning signal sounds when ignition key is in position I and the engine is at a standstill and goes out as soon as the engine runs and the generator starts charging the bat tery 31 Battery It also goes out when the ignition key is in 33 Starter switch with ignition key position 0 or is removed 34 Trailer socket e 35 Flat plug type fuse holder If the warning signal sounds while the engine is running the engine lubrication is not in order immediately check engine oil level refill if necessary however if engine lubrication is in order agria Servicec Warning Do not set ignition start switch to O while the engine is running This can damage the charging regulator Fuse A fuse 35 is located be
14. cause Petrol engine does not run smoothly Petrol engine does not stop when set to stop Petrol engine output too low Diesel Engine Diesel engine does not start Misfirings in diesel engine Excessive temperature in diesel engine Misfirings at high speeds Engine frequently stalls in dle Speed control linkages clogged or jammed Defective engine stop line earth missing Air filter clogged Loose cylinder head or damaged gasket Poor compression Speed control lever set to min Safety circuit is not set to start position Fuel tank empty or poor fuel Fuel line or fuel filter clogged Electrical cable not connected to solenoid valve Clogged fuel line or fuel filter Injector nozzle or injection line clogged Wrong injection pressure Clogged fuel line or poor fuel Vent opening in fuel tank cap clogged Water or dirt in fuel system Air filter clogged Injector nozzle or injection line clogged Lack of engine oil Impaired cooling Injector nozzle clogged Wrong injection pressure Air filter clogged aqria Remedy Clean speed control linkages Check line and connection check ground contact Clean air filter Tighten cylinder head exchange gasket Have engine checked Move speed control lever to Half soeed Set safety circuit to start position Fill fresh fuel Clean fuel line or filter Check electric line Clea
15. during work danger agria Hydrostatic Tool Carrier 5900 Taifun 9 1 Safety Instructions For all works with the tool carrier in particular for turning the machine operator must keep the distance to the machine given by the steering handles Riding on the implement during operation or in transport is not permitted If clogging occurs in the implement shut off the engine and clean the implement with an appropriate tool In case of damage to the tool carrier or to the implement immediately shut off the engine and have it repaired If steering causes problems immediately bring the tool carrier to a halt and turn it off Have the malfunction removed without delay To prevent the tool carrier from sliding on slopes make sure it is secured by another person using a bar or a rope This person must stay at a higher position than the vehicle and at a safe distance from the attachment at work If possible always work across the Slope End of Operation Never leave the tool carrier unattended with the engine running Before you leave the tool carrier shut off the engine Then close fuel taps Secure tool carrier against unauthorized use If tool carrier is equipped with ignition key remove the key For all other versions remove spark plug connector 10 aqria Implements Only mount implements with the engine and PTO shut off Always use appropriate tools and wear gloves when changing implements
16. screen and oil cooler sJagria Servicec N N R N NI NN WAI Exhaust System and Governor Check exhaust system C 18 governor link governor rod and governor springs on a regular basis for plant trash and clean clean with a brush or compressed air If necessary Danger of fire results when exhaust system is dirty Check each time before you take up operation Carburetor Adjustment gt O gt aqriga Service EN Re adjusting Valve Clearance O gt agria Service AAAAAA II e FA agria Hydrostatic Tool Carrier 5900 Taifun 49 5 Maintenance agria Diesel Engine Apart from observing all operating instructions it is also important to pay attention to the following maintenance instructions A G Only do all maintenance work with the engine shut off and FF ignition key disconnected 0 When working on mowing knives wear safety gloves Engine Please note that only the special care and maintenance ofthe engine required for the tool carrier is described here all other maintenance of the engine am LO see operating Instructions Lombardini engine Cleaning the Cooling System After a long period of operation the cooling system may become clogged by dirt and plant trash Uninterrupted operation with a clogged cooling system causes the engine to heat up and become damaged Always check cooling air screen C 8 and free from dirt and plant trash taken IN
17. speed than necessary for the work in hand 20 agria High engine speed is harm ful to any engine and consid erably affects its durability This applies especially for no load operation Any overspeed have the engine roar can result in immediate damage Cooling System The cooling system is fan cooled Therefore keep screen at recoil starter and cooling fins of cylinder clean and free from sucked in plant trash Idling speed Always ensure that idling speed is adjusted correcty At low speeds and with the speed control lever set to idle the engine is supposed to run smoothly and without run out Air Filter The air filter purifies the air intake A clogged filter reduces engine output agria Hydrostatic Tool Carrier 5900 Taifun 3 Devices and Operating Elements p g Petrol Engine agmnia Speed Control Lever The speed control lever B 9 on the steering handle is for stepless setting of engine speed from min idle to max full throttle Engine Shut off Switch The tool carrier is equipped with an electric shut off switch B 3 On pressing the switch the ignition is turned off engine is shut off Position I Operation Position 0 Engine off The engine shut off switch also serves to shut off the engine in an emergency situation Set the switch to 0 for fast shut off Safety circuit The tool carrier is equipped with a safety circuit lever B 4 When releasing the l
18. system not in order blocked ventilation filter blocked cooling fins B 13 B 14 34 agria Hydrostatic Tool Carrier 5900 Taifun 4 Commissioning and Operation agria Commissioning Please note that durability and operational safety of the engine depend to a large extent on its breaking in Always allow a cold engine to warm up for some minutes and never run it at full throttle at the beginning For the first 20 hours of operation break in period do not use the petrol engine at full power respectively for the first 50 hours of operation regarding the diesel engine Make sure you check and maintain air filters regularly and use clean fuel Only use branded petrol respectively branded diesel ensure timely provision of winter diesel fuel see operating instructions for Lombardini engine Only use fresh clean petrol not older than 3 months and approved fuel cans to be purchased in special shops Rusty sheet metal cans or fuel cans not suited for petrol are not permitted For the first commissioning or after longer periods of no operation fill fuel tank to maximum to avoid starting problems AN lA Be careful when dealing with fuel Fuel is easily inflammable sm and explosive in certain conditions Do not refill in closed rooms o Before each fuel fill shut off the engine and wait until it has cooled off o Never refill close to open fire inflammable sparks or hot engine parts Do not smoke during filling
19. the positive terminal of the battery to the Note manufac positive output of the charging unit The negative turer s instruc Output is dealt with in the same way tions Only switch the charging unit on after the battery is connected 5 Recommended charging current 1 10 ampere of the battery capacity Ah For re charging use a charging unit with a constant charging voltage of 14 4 V If the acid temperature exceeds 45 stop the charging The battery is fully charged if the charging voltage no longer increases within a period of 2 hours Maintenance Keep the battery clean and dry Only wipe the battery with a moist cloth otherwise there is a danger of explosion Do not open the battery Never leave battery in uncharged state Avoid A sparking and open flames near batteries Careful when handling battery acid etching Only use specified fuses If fuses are too strong the electric system will be destroyed danger of fire agria Hydrostatic Tool Carrier 5900 Taifun 51 5 Maintenance Machine Transmission Transmission oil is also hydraulic oil When changing to Bio hydraulic oil HEES drain oil filling and twice rinse the system see after sales service information 3 50 h 600 h 1 Oil dipstick A 1 2 Sealing ring for oil dipstick 3 Sealing ring for drain screw 4 Drain screw A 24 5 Oil filter cartridge A 27 aqria O Check oil level in transmission each time
20. B Push roller guard 2 over wheel motors Note notch for brake lever Fasten with screws 4 and washers 3 agria Hydrostatic Tool Carrier 5900 Taifun 63 Varnishes Wear Parts agria agria Order No Fuel Stabilizer for Petrol Engine 799 09 Fuel stabilizer pouch 59 Varnishes 181 03 Spray varnish birch green spray tin 400ml 71298 Spray varnish red RAL 2002 spray tin 400ml 50968 Spray varnish black spray tin 400ml Glues for screw fastening 559 94 Glue medium LOCTITE 242 bottle 50 ml 559 95 Glue strong LOCTITE 270 bottle 50 ml 559 96 Glue ultra strong LOCTITE 638 bottle 50 ml Surface Sealing 50968 Surface sealing liquid LOCTITE 573 tube 250 ml Wear Parts Petrol Engine 71622 Air filter element 18 HP 640 88 Foamed preliminary filter 18 HP 101 445 Air filter element cyklone P82 1575 789 91 Fuel filter 100 102 Arr filter element 22 HP 71623 Engine oil filter cartridge 685 60 Spark plug Bosch FR8 DC CHAMPION RC12YC 759 28 Flat plug fuse 15A Diesel Motor 101 445 Air filter element cyklone P82 1575 101 444 Rain protection cap air filter 597 54 Engine oil filter 478014 Fuel Filter 759 28 Flat plug fuse15 A Transmission 009 16 O ring 16x22x1 5 oil dip stick and oil drain plug 52706 Oil filter cartridge Emergency Tyre Repair 713 13 Tyre repair gel Terra S bottle 11 Lists of Spare Parts 997 153 997 083 997 137 64 Tool carrier 5900 Bison Taifun Implements for 3400 5500 5900 Briggs a
21. Nm agria Hydrostatic Tool Carrier 5900 Taifun 55 5 Maintenance aqria Safety circuit Check safety circuit function each time you take up operation and each time you maintain the machine e With clutch engaged and upon release of safety lever B 4 the engine must automatically come to a stop e Check electric lines and connections and exchange if necessary gt agria Service Engine Shut off Switch Petrol Engine Check function of engine shut off switch each time you take up operation and each tim you do maintenance work e With shut off switch in position O the engine must come to a stop e Check electric lines and connections 2 agria Servicec Diesel Engine Check function of engine shut off switch each time you take up operation and each tim you do maintenance work e With shut off switch in position 0 the engine must come to a stop Check electric lines and connections 2 agria Servicec 56 agria Hydrostatic Tool Carrier 5900 Taifun 5 Maintenance 1 Hand lever 2 Retaining spring 3 Threaded end of cable 4 Adjusting pin aqria Adjustments on Levers Check clutch play or clutch adjustment each time you operate the machine If necessary re adjust especially after commissioning the machine during break in period and after exchanging clutch linings and brake pads Clutch A 3 5 mm Clutch play The Bowden cable must be placed in the hand lev
22. Prior to starting the works check shifting position Pay attention to the version Valve steering 13 LV13 or valve steering 15 LV15 Gi Coasting operation or towing up to max 4 km h Trailing is not permitted Hydraulic Steering With the hydraulic steering the inner wheel at the curve becomes slower up to the standstill the outer wheel at the curve keeps it velocity Steering eBy the steering movement at the steering handle the hydraulic steering is activated with running engine e Steering only during driving not upon a standstill e Ihe stronger the steering movement the quicker the hydraulic steering Locking the Hydraulic Steering By pulling and turning the shifting mechanism B 8 the hydraulic steering is locked and steering is realized by muscular strength When the lock is opened the hydraulic steering is connected again Use Operation at the slope Similar to a differential lock or for lifting out an implement agria Hydrostatic Tool Carrier 5900 Taifun 25 3 Devices and Operating Elements agria Central Brake To slow down or park the machine on hilly ground use the combined central parking brake Central Brake Swivel the eccentric lever B 2 backwards and up both drive wheels are braked Release the eccentric lever and the lever swivels back to the original position brake is released e Parking brake Swivel the eccentric lever B 2 backwards and up
23. and parts thereof For mounting and dismounting implements bring stand into proper position and ensure stability Secure tool carrier and implements against rolling off parking brake wheel chocks Beware of injuries while coupling implements Work with particular care Hitch implements as specified and only couple at specified points Secure tool carrier and implement against unauthorized use and rolling off when you leave the machine lf necessary install transport or security devices and secure Mowing Implement Handle with care Sharp blades of the cutter bar may cause injuries Remove knife guards only for mowing and refit immediately after work has finished For transport and storage always mount the knife guards Secure finger bars additionally with tension springs Do not transport the dismounted cutter bar without knife guards agria Hydrostatic Tool Carrier 5900 Taifun 1 Safety Instructions When mounting and dismounting the cutter bar make sure all blades are protected by the knife guards To exchange the knife and to mount dismount the knife driver make sure that you turn screws away from cutting blades For grinding the mowing knives always wear safety goggles and gloves Weights Fit weights properly and at specified points Maintenance Never carry out any maintenance or cleaning with the engine running Before you work on the engine always remove spark plug connector petrol
24. before you take the machine into operation and after every 25 operating hours oil dip stick and filling opening A 1 With the tool carrier parked in horizontal position the oil level must be between the max and min marks e Screw out oil dip stick clean with clean cloth and screw back in Take dip stick out again and read oil level refill transmission oil if necessary Refilling volume between min and max 1 Transmission oil filter change after the first 50 operating hours and then always after 200 operating hours Tilt machine forwards onto the connection flange Screw out oil filter A 27 and replace it for new filter wet the sealing ring with some oil Dispose of oil filter as directed Transmission oil change with simultaneous oil filter change after the first 50 operating hours and after every 600 operating hours while the engine is still warm O Keep oil filler plug A 1 and drain plug A 24 extremely clean as well as surrounding parts to prevent dirt from penetrating into the transmission e Open drain plug collect old oil in proper container and dispose of properly e Clean drain plug the drain plug has a magnetic core and therefore attracts metallic powder e Check sealing rings and exchange if necessary e Screw in drain plug with o ring and tighten e Fill in fresh transmission oil up to level mark max e For proper oil quantity and quality re
25. cate all lubrication points oil and let tool carrier run for a short time to press water out Apply grease generously to leave a grease ring around bearings to prevent water plant sap and dirt from penetrating Clean engine only with a cloth Avoid spraying with air com pressed water jets as water might leak into ignition and fuel system causing malfunctions 58 agria Hydrostatic Tool Carrier 5900 Taifun 5 Maintenance Storage For longer periods of no operation a Clean thoroughly Repair paint coat b Engine preservation Petrol Engine e Drain fuel completely or fill fuel tank and add fuel stabilizer agria no 799 09 Observe enclosed instructions Let engine run for approx 1 minute e Change the engine oil e Fill a tea spoon approx 0 031 of engine oil into the spark plug opening Slowly crank the engine O Reinstall the spark plug and set the piston to compression via the recoil starter pull the starter grip until resistance is felt valves are closed O Slowly crank the engine after every 2 3 weeks spark plug connector is removed Then set the piston to compression again Diesel Engine Change the engine oll For longer storage close exhaust pipe and air filter opening with crape or simi lar tape agria Hydrostatic Tool Carrier 5900 Taifun agria c Drive wheels Support drive wheels in such a way that tyres have no ground contac
26. ch does not decouple Clutch slips No wheel drive Excessive vibration Clutch lever misadjusted Clutch lever misadjusted Worn out clutch Clutch is not engaged Idle shift is operated Loosened attachment bolts aqria Remedy Check Ignition lock Check electrical cable to solenoid valve Check solenoid valve Clean air filter Tighten cylinder head exchange gasket Have engine checked Charge or replace the battery Replace fuse Check harness and E starter Charge or replace the battery Replace fuse Check harness and E starter Move start switch to TI Replace beeper Replace fuse Replace oil pressure switch Check harness Check regulator Replace fuse Check engine oil level refell if necessary Check harness Check regulator Check generator Adjust clutch free play Adjust clutch free play Exchange clutch disc Engage clutch using the clutch lever Activate hydraulic drive Tighten attachment bolts Page BM 71 51 x x 51 33 x 51 33 x 37 x 33 x x x 33 44 BM x x x 57 57 x 23 25 58 For this purpose contact your agria workshop BM see separate engie operating instructions 62 agria Hydrostatic Tool Carrier 5900 Taifun Screen fan Roller guard agria Kit Sreen fan Option Parts set 799 60 Recommendable for mowing use Roller guard Option Parts set 760 58 Assembly A Clip roller guard support 1 to draw spindle of wheel motors
27. ctane number 85 RON refer to fuel recommendations Fuel tank capacity abt 7 51 Fuel consumption 312 g kWh Fuel filter feul online Air filter Dry filter element with foamed preliminary filter Carburetor Horizontal float carburetor agria Hydrostatic Tool Carrier 5900 Taifun Noise level e In accordance with EN 12733 appendix B Noise level at operators ear Double knife drive L 90 5 dB A Rotary mower 80 L 91 2 dB A Safety Mulcher105 L 91 1 dB A e In accordance with 2000 14 EC appendix Ill part B chapter 32 lawn mower Acoustic power level Double knife drive L 103 8 dB A Rotary mower 80 L 106 3 dB A Safety Mulcher 105 L 106 4 dB A Vibration acceleration value In accordance with 2002 44 EC and EN 12733 on handlebar grip With Rotary mower Safety Mulcher EE a lt 2 9 M S Double knife drive a 4 67 m s Operability on Slopes Engine is suited for use on slopes with OU level at max upper level mark possible up to 45 inclination 100 17 2 Specifications Petro Engine agria Petrol Engine 22 HP Rated speed 3600 rom Manufacturer B amp S Type Vanguard 22 HP 356447 0175 a no load speed 4000 rpm Version
28. ctive ear plugs and solid shoes For operation with PTO powered attachments Switch on PTO using the PTO shifting mechanism B 7 O Pull Slightly clutch lever B S unlock pawl B 6 and slowly let go while pressing the throttle Carefully engage the clutch the exact 0 A position of the driving lever or the twist grip is not always reached the implement will possibly start directly Release the parking brake O Set driving speed with the driving lever B 10 or the twist grip B 12 or according to the conditions and requirements Changing the driving direction from forward to reverse Slowly move driving lever B 10 or twist grip B 12 to the rear bottom Proceed vice versa for direction change from reverse to forward Never leave tool carrier unattended with f Ai 7 LW A the engine running A Danger Zone xx A Keep out of the machine s danger zone ES AW _ during starts and operation 42 agria Hydrostatic Tool Carrier 5900 Taifun 4 Commissioning and Operation agria Petrol max 45 Diesel max 25 max 35 Mowing on Mowing on plain surfaces Slopes Note for Mowing After mowing or in case of grass clog ging O set driving lever to idle position The mower comes to a stop but not the knives thus freeing the cutter bar from grass 2 Set PTO shifting mechanism to po sition O Working on Slopes To prevent the tool carrier from slidi
29. ctrical starter automatic supplementary fuel at the start Battery 12 V 45 Ah Fuel Commercial diesel fuel min cetane rating of 45 refer to fuel recommendations FUEI TOF ee eege Coarse mesh strainer in filler neck Fine mesh strainer in fuel tank drain hole Fuel tank capacity abt 4 I Fuel pump Air filter Dry filter element with foamed preliminary filter and cyclone pre separator agria Hydrostatic Tool Carrier 5900 Taifun Ee Forced feed lubrication Ee Full flow oil filter externally Engine oil ee eet EE without oil filter approx 1 8 with oil filter approx 1 95 Multi grade oil at ambient temperature 15 to 45 C SAE 10W 40 API SC or higher at ambient temperature 25 to 15 SAE 5W 20 API SC or higher Noise level e In accordance with EN 12733 appendix B Noise level at operators ear Safety Mulcher L 85 7 dB A e In accordance with 2000 14 EC appenalx Ill part B chapter 32 lawn mower Acoustic power level Safety Mulcher 105 7 dB A Vibration acceleration value In accordance with 2002 44 EC and EN 12733 ON handlebar grip With Safety Mulcher a 2 08 M S Operability on Slopes Engine is suited for use on slopes with oil level at max
30. d cartidge if they are very dirty or damaged Cleaning preliminary air filter O Dispose cover O Carefully remove the preliminary filter from the cartridge Wash preliminary filter in detergent and water O Squeeze the preliminary filter in a clean cloth O Soak preliminary filter in engine oil O squeeze the preliminary filter in a clean absorbing cloth to remove spare oll Reinstall the preliminary filter on the cartridge Reposition the cover 46 agria Hydrostatic Tool Carrier 5900 Taifun 5 Maintenance Petrol Engine AQriad Cleaning air filter cartidge Clean preliminary air filter gt No O O Remove knurled nut and plate Carefully remove the cartridge in order to keep foreign objects out of the carburetor To clean the cartridge tap it carefully on a flat surface Do not use petroleum based sovlents which can cause wear of the cartridge Do not use compressed air because this can damage the cartridge Do not oil the cartridge Reassemble cartridge plate and knurled nut Assemble pre filter and cover gt No 0 O Cyclone Air filter e Clean air filter insert B always after 25 operating hours through careful tapping at one end Wash and dry the filter cover C Do not use compressed air to blow out dust of filter insert and do not treat with oil Change air filter insert after tapping out 3x and at the latest after every 100 operating
31. de mancheron les douilles ultra de mancheron HE CZ DD O OA O ID E Verifier d plomiracil des moteurs derouss rl Is H HA R gierte carburateur et III ww R gler Ta jeu des soupapes el II m Neroyerlaculasse JAU e ww Graisser le boulon arret de maneheron Wolf II RR Netoyer recteur ete v re III IT Haw Remplacer les durtes de carburant el III III We Ge AR a Remplacer le filtre carburant Remplacer le filtre carburant Car Graisser toutes les pieces mobiles 11 68 agria Hydrostatic Tool Carrier 5900 Taifun xcurpy y Uy x lt MN agria Only petrol engine Only diesel engine Item in lubrication chart page 66 resp 67 Each time before you take up operation After each cleaning especially with a high pressure cleaner At least once per year Checks and maintenance to be executed by operator Maintenance to be executed by professional workshop Maintenance should be carried out by your agria workshop See separate engine operating instructions After 2 years agria Hydrostatic Tool Carrier 5900 Taifun 69 Hydraulic Chart O YN O RA ON Transmission incl oil reservoir Hydraulic pump Valve steering Filter cartridge Lower handlebar with oil cooler Wheel motor left Wheel motorright Hydraulic hose left B Hydraulic hose left A Hydraulic hose right A Hydraulic hose right B Oilcooler 70 agria Hydrostatic Tool Carrier 5900 Taifun Designation
32. e install the comple te wheel motors M 1 to the front flan ge bolting template M 2 e Previously clean flange bolting tem plate e Do not unfix hydraulic lines and bow den cables e Tighten attachment bolts M 3 with 45 Nm agria Hydrostatic Tool Carrier 5900 Taifun 29 3 Devices and Operating Elements aqria Continuous portal axle adjustment option for article 5939 011 Adjustment to front or rear O Pull parking brake P O Release ball handle lever O Pull machine back or move machine forwardon steering spar Min clearance to attachment for drive wheels 20 mm O Pull ball handle lever O Ball handle lever must not point downward Press ball handle lever axially inward until it unlocks and turn upward 30 agria Hydrostatic Tool Carrier 5900 Taifun 3 Devices and Operating Elements aqria Mounting and Dismounting Implements Only mount and dismount implemens with engine off Mounting Implements e Ensure that coupling surfaces on tool carrier and implement are clean O For PTO driven implements set shift lever 4 on implement to position 0 Slide pegs 2 of base machine into hooks 3 of implement Fold both eye bolts 1 over coupling flange Note o Make sure flanges 5 are properly centred and flat fitted e Tighten cap nuts evenly For PTO driven implements Set shift lever 4 at the implement to T shifting takes place
33. e applies Accordingly check the tool carrier for road and operational safety each time you take up operation Only persons familiar with the tool carrier and instructed on the hazards of operation are allowed to use maintain and repair the tool carrier Young persons of 16 years or younger may not operate the tool carrier Only work in good light and visibility Operator s clothes should fit tightly Avoid wearing loosely fitting clothes Wear Solid shoes Note the warning and instruction signs on the tool carrier for safe operation Compliance is for your own safety When transporting the tool carrier on vehicles or trailers outside the area to be cultivated ensure that the engine is shut off 8 agria Hydrostatic Tool Carrier 5900 Taifun 1 Safety Instructions Careful with rotating tools keep at a safe distance Beware of coasting tools Before you start any maintenance or repair on them wait until tools have come to a complete Stop Foreign powered parts shear and crush Riding on the attachment during operation is not permitted Implements and weights affect the driving steering braking and tip over characteristics of the tool carrier Therefore ensure steering and braking functions are sufficient Match operating speed to conditions Do not change settings of governor High engine speed increases risk of accidents Working Area and Danger Zone The user is liable to third parties work
34. er support on bottom position Adjustment O Remove retaining spring 2 and remove cable end 3 and adjusting pin 4 out of bracket in hand lever Adjust the adjusting pin 4 to a play of X or idle is present in position 0 Screw adjusting pin in to reduce play screw out to increase play Place cable end and adjusting pin back into bracket and fit retaining spring 2 agria Hydrostatic Tool Carrier 5900 Taifun 57 5 Maintenance aq ria Twist grip shift Check for proper operation and adjustment when performing maintenance and adjust if necessary Seiting Set the twist grip shift on the Bowden cable adjustment screw so there is no play so that the marking point on the twist grip matches the 0 position of the pump and the pictograph Twist grip locking lever Setting the clamp Loosen threaded rod about 1 revolution with hex key Set locking lever so that es twist grip can turn a twist grip is clamped cannot turn General Maintenance O Every time You take up operation watch out for fuel and oil leakage repair if necessary 2 Regularly check bolts and nuts for tight fit and tighten them as necessary At least once a year and after cleaning Slightly grease all sliding and moving parts e g speed control lever lever bearing etc with bio lubricating grease and bio lubrication oll Cleaning After each cleaning spraying with water especially with air compressed water jets lubri
35. ever the ignition system is turned off engine is shut off O Stop position When releasing the lever the ignition system is turned off engine is shut off Beware engine keeps running due to centrifugal mass O Start position For starting the engine and for short breaks pull the clutch lever B 5 and lock with pawl B 6 Operating position To operate the machine press safety circuit lever B 4 A Do not fasten safety circuit lever The safety circuit lever also serves to shut off the engine in an emergency situation Release the safety circuit lever for fast engine shut off The lever automatically goes to STOP position agria Hydrostatic Tool Carrier 5900 Taifun 21 3 Devices and Operating Elements g g Diesel Engine QE Speed Control Lever The speed control lever B 9 on the steering handle is for stepless setting of engine speed from min idle to max full throttle Safety circuit The tool carrier is equipped with a safety circuit lever B 4 When releasing the lever the ignition system is turned off engine is shut Off O Stop position When releasing the lever the ignition system is turned off engine is shut off Beware engine keeps running due to centrifugal mass 2 Start position For starting the engine and for short breaks pull the clutch lever B 5 and lock with pawl B 6 O Operating position To operate the machine press safety circuit lever B 4
36. fer to chapter Specifications e Close filling opening with plug dip stick 52 agria Hydrostatic Tool Carrier 5900 Taifun 5 Maintenance aqria Oil cooler After mowing for longer periods of time clogging of plants and dust may occur in the cooling system Sustained operation with the cooling system clogged lets the transmission heat up and causes damage Petrol Engine Always check oil cooler C 21 22 and remove dirt and plants sucked in clean with a brush or compressed air Diesel Engine Clean fan system after every 100 hours of operation or at least once per year preferably before the season starts more often if heavily soiled Where possible combine cleaning with a cleaning of the engine cooling system Hydraulic hoses Check hydraulic hoses always after 200 operating hours or at least once per year for closeness and damage Brake Always after 200 operating hours or at least once per year check brake jaws and brake operating system for unhindered movement and efficiency Jagria Servicec Wheel Motors Always after 200 operating hours check for straight driving with the steering handle in neutral position Jagria Servicec Loading Belt Check loading Delt or damage before each use and each time You maintain the machine replace it not later than 10 years agria Hydrostatic Tool Carrier 5900 Taifun 53 5 Maintenance A 8 54 3 J B z 200 h J B 3 100h B aq
37. filter clogged Carburetor misadjusted Short firing intervals Incorrect idle mixture Firing interval too long defective spark plug Carburetor misadjusted Air filter clogged aqria Remedy Connect spark plug connector Set choke lever to position CHOKE Set engine shut off switch to I Set safety circuit to start position Fill fresh fuel Clean fuel line Clean adjust or exchange spark plug Dry and clean spark plug and start at full throttle Check line and connections Tighten attachment bolts Set CHOKE lever to operating position Fit connector tightly on ignition cable fix ignition cable retaining device fit connector tightly on spark plug Exchange fuel filter fill fresh fuel Exchange fuel tank cap Drain fuel and fill fresh fuel Clean air filter or exchange Re adjust carburetor Refill oil immediately Clean cooling fan screen clean internal cooling fins Clean air filter Re adjust carburetor Adjust spark plug Adjust carburetor Adjust or replace spark plug Re adjust carburetor Clean air filter agria Hydrostatic Tool Carrier 5900 Taifun Observe safety instructions Have all serious malfunctions on the machine or engine repaired by your agria workshop They have the proper tools Improper repairs can only add to the damage Page 37 37 37 35 48 48 48 97 48 46 47 BM 44 49 46 47 BM 48 BM 48 46 47 6 Troubleshooting Problem Possible
38. grey ws white 2 Magnet ignition system 3 Engine shut off switch 4 Switch in clutch lever e 5 Switch in safety circuit lever Connection at the engine 6 Generator 12 V 16A u 7 Regulator 12 V A Ignition system 8 Fuse 25A gt Safety circuit steering 9 Socket 12 V DIN 9680 A 10 Start switch Ignition system Start switch 11 Battery 12 E Starter 12 V C 2x ge Generator 13 Start relay gt Regulator 14 Beeper 17 Switch engine oil pressure E ro Regulator3 Start switch 18 Fuel Domp electrical optional 19 Stop valve in the carburetor only version 22 HP agria Hydrostatic Tool Carrier 5900 Taifun 73 Electrical Wiring agria Diesel Engine Nx25 Rx1 5 Mx1 5 1 Ignition lock Start switch 2 Regulator colour x cross section 3 E Starter 4 Battery colour 5 Alternator A white 6 Switch engine oil pressure B blue 7 Charge indicator C N pink black 8 Oil pressure indicator G yellow 9 Engine temperature indicator H grey 10 Temperature switch M brown 11 Fuse N black 12 Working hours counter R red 13 Solenoid valve V green 14 Switch safety circuit lever 15 Switch clutch lever 16 Fuse for Socket 17 Socket 74 agria Hydrostatic Tool Carrier 5900 Taifun Designation of Parts Diesel Engine Fig D Engine Lombardini 25LD425 Fuel tank Fuel tank cap Elektrical socket12 V DIN 9680 A Oil filler tube Muffler Battery Fuse for socket Cooling air screen Air fi
39. heel combination and Track Widths Q le Q O TA A YY ET TAY O rrr DO tz rs rer N CO OO OO ON CO CH _ amp dD DOMDODMOKRKR o OC YT e e YT YT r O st LOL O O O Ge N NI LO LO LO ID IND ID OSH E PR AU EU PE eee SAT sl XI si si si si si st 05 lou OU OU NH HN x E y CO OO OH CH SS GG gt SNS oA cow N N o o O o ojo Y LO IM ID O O ka V G A EE G lt 38 M lt a lt M lt fap O ch CO N gt _ Hz Mm ITS lt o lt st B fe fap O H PES E lt N gt d o lt lt O N or NP N EN NI CO NINI si Let le N O T il a NO O oO o OlOlo A ae Lo 10 amp A 0 lt E co a CH S LO x x ON CO Oo Oo ICI lt lt lt lt lo o ll el ojt re ee bas IS les olo el leck JE 2 818 8 5 8 SIL x r oO Oil x oO x ie NES NIS x N N N a Pel ott olo 1 agria Hydrostatic Tool Carrier 5900 Taifun 15 2 Specifications Clutch Single disc dry clutch Transmission coo Hydrostat Driving speeds FOTWATO io 0 7 0 km h Reverse 0 3 6 km h E 805 rom gear independent at 3600 engine rom direction of rotation clockwise looking on PTO constant in forward and reverse Steering Fully hydraulic steering handle Steering handle fixable with disconnection of the hydraulic system for manual stee
40. hours or when damaged Every time you take up operation discharge the air preliminary filter by squeezing the dust extraction valve D agria Hydrostatic Tool Carrier 5900 Taifun 47 5 Maintenance aq ria Petrol Engine Wire brush Spark Plug After every 100 operating hours remove soot from spark plug electrodes using a wire brush e check spark plug gap and set to amp 100 h 200 h 1 0 mm Exchange spark plugs after every 200 hours of operation Fuel Hoses Exchange fuel hoses every 2 years Leaking hoses must be exchanged immediately Fuel Filter Exchange fuel filter C 9 every year Note direction of flow 48 agria Hydrostatic Tool Carrier 5900 Taifun 5 Maintenance agria Petrol Engine Cleaning the Cooling System After mowing for longer periods of time clog ging of plants and dust may occur in the cooling system Sustained operation with the cooling system clogged lets the engine heat up and causes damage Clean engine only with a brush or compressed air Do not spray with water A TIN AR Wy C WA HA 7 e DET AN FF FR ANY PA HAH SG A A TFT ZT HI A Always check cooling air screen C 5 and remove dirt and plants sucked in Clean fan system after every 100 hours of operation or at least once per year preferably before the season starts Take off fan case and clean cooling fins on both cylinder and cylinder head in addition to the fins cooling air
41. ieing up towing away 2 agria Hydrostatic Tool Carrier 5900 Taifun Designation of Parts agria O yn i TA UU sA UI aC die el 7 By Sch Ze Fig A 5832 1 SE 24 ES 26 27 28 agria Hydrostatic Tool Carrier 5900 Taifun 3 Designation of Parts agria Fig A Fig DO Dna aka D Sch 13 14 Transmission hydraulic oil dipstick and filling opening Ball head for hood carrier front Idle speed shifting mechanism bypass Nameplate machine identification no Ball head for hood carrier rear Transmission venting plug Loading belt Steering handle locking bolt rollers Steering handle central screw Lower steering handle Steering bar Oil cooler only vers diesel engine Eye bolt with cap nut top PTO shaft Eye bolt with cap nut bottom Transmission oil drain screw Brake drum Wheel hub Oil filter cartridge Engine B Ball handle for lateral steering bar adjustment Eccentric lever for central brake Engine off switch Safety circuit lever Engine clutch engagement lever Pawl for engine clutch lever Connection mechanism for PTO shaft Operating mechanism for steering handle lock Speed adjusting lever Lever for stepless adjustment of driving speed and forward reverse driving Operating hour counter Twist grip for stepless adjustment of driving speed and forward reverse driving special equipment Control lamps only vers diesel engine Ignition lock on
42. ill any fuel use a proper filling device e g funnel In case of fuel spillage pull the tool carrier away from the spillage before you start the engine Make sure fuel is of specified quality Store fuel in approved cans only Liquids leaking under high pressure e g fuel can penetrate the skin and cause severe injuries Immediately see a doctor Store anti corrosive agents and Stabilizing liquids out of reach of children If sickness and vomiting occur see a doctor If fuel has contacted eyes rinse them thoroughly avoid inhaling of Vapours Read and instructions Before you dispose of opened and seemingly empty pressurised tins e g of assist starting liquids make sure they are completely empty Empty them in ventilated places safe from spark formation or flames If necessary dispose of tins in hazardous waste deposits Be careful when draining hot oil danger of burns observe enclosed Make sure oil used is of specified quality Storage is in approved cans only Dispose of oil greases and filters seperately and properly 12 aqria Hydraulic System The hydraulic system is subjected to high pressure When connecting hydraulic motors ensure the specified connection of the hydraulic hoses Hydraulic oil emerging under high pressure may penetrate the skin and cause serious injuries In case of injuries immediately consult a physician risk of infections Prior to works on the hydra
43. ill destroy the electrical system danger of fire Always cover positive pole with specified cover or terminal cap Persons having a pacemaker may not touch live parts of the ignition system when the engine is running agria Hydrostatic Tool Carrier 5900 Taifun aqria Explanation of protective covers mounted Before starting the engine bring covers in pro per position Warning Signs Before any cle 7 aning mainte FI nance and repair work shut off the engine and pull G spark plug connec EJ tor petrol engine resp ignition key diesel engine Do not work without Y With engine run ning keep at a safe distance from cut ting knife gt E E SY Do not touch mo ving machinery parts Wait until they have come to a complete stop With engine run ning keep at a safe distance kl Y ts dp When working with the machine wear individual protective ear plugs Wear protective gloves Wear solid shoes lalala 13 Specifications weie agria AA El St SE Dimensions a e axle displaced forwards Benzin Motor C h 20x8 00 10 00 10 EL an 21x11 00 8 250 663 760 270 167 1350 5 00 12 AS ee 50 12 ca 1010 ee 50 12 Diesel Motor o h 20x8 00 10 10 LEI ES 21x11 00 8 510 713 760 270 167 1350 5 00 12AS Ee 50 12 ca 1010 ee 12 14 agria Hydrostatic Tool Carrier 5900 Taifun 2 Specifications W
44. ine leave CHOKE lever in normal operating position O Set engine shut off switch B 3 to operating position I O Set speed control lever B 9 to 1 3 throttle Pull clutch lever B 5 and lock paw B 6 start position O insert key into ignition start switch C 33 and turn right to position TI e Warning signal sounds Start engine from a position outside the danger zone Turn ignition key further to the right to position START As soon as the engine starts let go ignition key it automatically moves back into position T e Or start manually with the reverse starter If the engine does not start and re start is necessary turn key back to position O to repeat start re start lock O Trailing is not permitted Once the engine has started let it warm up for some time Slowly push choke back into operating position if necessary agria Hydrostatic Tool Carrier 5900 Taifun 37 4 Commissioning and Operation x 30 sec Petrol Engine AG ria Shutting off Petrol Engine O se speed control lever to idle position and let engine run idle for approx half a minute O Set engine shut off switch to 0 Turn key back to position 0 battery charge indicator goes out O Close both fuel taps Secure tool carrier against unauthorized use disconnect key Engine shut off switch B 3 also serves as emergency off switch If necessary set s
45. ing within the tool carrier s working range Staying in the danger zone is not permitted Check the immediate surroundings of the tool carrier before you start it Watch out for children and animals Before you start work clear the area from any foreign object During operation always watch out for further objects and remove them in time For operation in enclosed areas ensure that a safety distance is kept to enclosures to prevent damage to tools aqria Operation and Safety Devices Before you start the engine Become familiar with the devices and operating elements and their functions Above all learn how to turn the engine off quickly and safely in an emergency situation Ensure that all protective devices are mounted and positioned to provide protection With no implement mounted make sure PTO shaft is covered with the protective cap Starting the engine Do not start engine in closed rooms The carbon monoxide contained in the exhaust fume is extremely toxic when inhaled Before you start the engine set all operating elements to neutral or idling position For starting the engine do not step in front of the tool carrier and the implement Do not use assist starting liquids when using electrical assist starting devices jumper cable Danger of explosion Operation Never leave the operators position at the steering handle while tool carrier is at work Never adjust the operating handles
46. ing the Petrol Engine Shutting off the Petrol Engine Starting the Diesel Engine Shutting off the Diesel Engine 41 ODErAaUON senora iad Danger Zone anan Working on Slopes 5 Maintenance Petrol Engine Engine ON nie AIM EEN Spark Plug occcccconcnccconcnccconnnns PUTO sonara Cooling System Exhaust and Governor Diesel Engine an00annananaanaann Ballery tee MACHINE nen Transmission Hydraulic Oil Steering Handle Valve Steering Safety circuit a Adjustments on Levers General Maintenance SOG ento 6 Troubleshooting Screen Fan Roller Guard Varnishes Wear Parts Hydraulic Hoses 000000000000aann Lubrication Chart Inspection and Maintenance Chart 68 Hydraulic Chart 70 Electrical Wiring 73 74 Conformity Declaration 77 Note fold out pages FIOS AP B aa 3 Fig C Petrol Engine 72 Fig D Diesel Engine 76 agria Hydrostatic Tool Carrier 5900 Taifun 5 Recommendations Lubricants and Anti Corrosive Agents Use the specified lubricants for engine and transmission see Specifications We recommend using bio lubricating oil o
47. le Gairfrais AIRA Has Nettoyer autour du pot d chappement x IK I TI Faso Nettoyer le r gulateur de r gime TARRO TUT TS Verifier To niveau dhuile moteuricompl ter DIS I KT E iasa a an Resserrer les crous ou goujons de roues Premiere vidange d huile moteur cae IIA memes SITTI CTT IL puis toutes les Premier nettoyage du filtre a l huile e ttt tt 5 S Page Nettoyer le filtre air cyclone Nettoyer le filtre air cyclone filtre air cyclone aS V iterio nic orale pra NG GG GG E DEE CES EE E EC A CU RER SSES Hg Resserrer les crous de moyeux de roues c les crous de Resserrer les crous de moyeux de roues de roues KI Remplacer le filtre huile b v 1 re fois ae ef Oe Premiere vidange d huile b v Ea MIEL V rifier la V rifier la sangle DOS RES ES les Graisser les glissi res de la soupape sid de la Graisser les glissi res de la soupape sid Nettoyer la bougie R gler l cartement des lectrodes Remplacer le filtre huile moteur ol Remplacer le filtre huile moteur ol filtre NUNG olga EE pt EES KA Nettoyer les deflecteurs les ailettes de refroidissement le refroidisseur a huile 49 50 plus tot si n cessaire et Graisser rouleaux de blocage mancherons rouleaux de Graisser rouleaux de blocage mancherons mancherons HEHE Remplacer la cartouche de filtre a air 46 47 51 plus t t si n cessaire Contr ler les douilles ultra
48. ll paragraphs in these operating instructions which affect your safety Pass all safety instructions to other users and operators Due Use The tool carrier is a hand controlled automatic single axle machine which can power and or pull various implements approved by the manufacturer Areas of application are for such as turning over the ground mowing grass and meadowland snow clearance and sweeping due use Any other type of operation is considered undue The manufacturer Is not liable for any damage resulting from undue use for which the risk lies with the user alone When the single axle tractor the tool carrier the multi purpose machine is used on public roads the local national road traffic rules must be observed e g reflectors lights The single axle tractor the tool carrier The multi purpose machine is not intended for use with a trailer on public roads or as as a tractor unit without implements Due use includes compliance with manufacturer s instructions on operation maintenance and repair Any unauthorized changes to the tool carrier render manufacturer liability null and void aqria General Instructions on Safety and Accident Prevention Basic Rule The standard accident prevention regulations must be adhered to as well as all other generally accepted rules governing operational safety occupational health and road traffic regulations For drives on public roads the latest traffic cod
49. lter Oil drain plug Oil dip stick Fuel pomp Oil filter Hydraulic oil cooler Engine no underneath E Starter agria agria Hydrostatic Tool Carrier 5900 Taifun 75 Designation of Parts Engine agria Fig D Engine Lombardini 25LD425 76 agria Hydrostatic Tool Carrier 5900 Taifun Conformity Declaration agria EG Konformit tserkl rung CE D claration de conformit EC Declaration of Conformity EG conformiteitsverklaring CF NL Wir Nous We Wij agria Werke GmbH Bittelbronner Str 42 D 74219 M ckm hl W rtt erklaren dass das d clarons que le produit herewith declare that verklaren dat het Produkt the product produkt Geratetrager Porte Outils Tool Carrier Werktuigdrager Taifun 5900 241 251 253 521 mit allen einschlagigen est conforme a toutes les conforms to all relevant voldoet aan de Bestimmungen der EG exigences respectives specifications of the desbetreffende bepalingen Maschinenrichtlinie selon la directive relative Directive on Machinery van de EG machinerichtlijn _ 2006 42 EG in aux machines 2006 42 CE 2006 42 EC 2006 42 EG Ubereinstimmung ist La machine est aussi De machine voldoet ook Die Maschine ist auch in conforme a toutes les It is also conform to all aan de desbetreffende Ubereinstimmung mit allen exigences respectives relevant specifications of bepalingen van het einschlagigen selon les directives CE following EC directives volgende EG richtlijnen Bestimmungen der suivantes 2004
50. lter and tank Or add a fuel stabilizer For further instructions refer to Engine Preservation aqria Diesel Engine This Diesel engine runs on conventional Diesel fuel of a min cetane rating of 45 Do not use Diesel fuel oil substitutes they may be harmful to the fuel system Fuel should be free of water or dust Winter operation To ensure reliable winter operation use winter diesel fuel to be purchased at fill ing stations At outside temperatures of below 15 C take the following additional precautions add commercial flow conditioners or add paraffine oil to depress diesel pour point Paraffine winter summer Oil diesel diesel fuel fuel pour point 50 app 31T app 25T 30 app 26T app 15T 10 app 20T app 9T As a last resort you can add up to 30 of regular petrol to avoid paraffine deposits However this has negative effects on consumption rate and performance see operating instruc LO tions Lombardini engine The Lombardini diesel engine can be operated to a limited extent using biofuel RME Rape methyl ester Care must be taken that the oil change intervals given in the operating instructions must be halved a reduction in operating performance of approx 10 should be expected agria Hydrostatic Tool Carrier 5900 Taifun 7 1 Safety Instructions Before starting the engine read the operating instructions and note Warning A This symbol marks a
51. ly set or changed with the forefinger or the thumb at the lever B 10 e he zero position is set when the marking at the driving lever is congruent with the 0 at the pictogram and is in contact with the spring detent e When turning the driving lever forwards the driving speed is steplessly increased forwards and accordingly backwards if the driving lever is turned backwards and down Twist grip shift model special equipment e The driving speed forward or reverse is steplessly set or changed with the twist grip B 12 O The zero position is set when the marking at the twist grip is congruent with the 0 at the pictogram e When swiveling the twist grip clockwise the driving speed is steplessly increased forwards When swiveling the twist grip anti clockwise B 12 Marking en speed is steplessiy increased O The locking lever can be used to prevent the twist grip from turning accidentally Locking lever locked y Locking lever unlocked 24 agria Hydrostatic Tool Carrier 5900 Taifun 3 Devices and Operating Elements agria Coasting Operation e he machine can be coasted without engine if the idle shift is opened position O e The idle shift A 3 is arranged at the right front of the tool carrier underneath the hood and can be operated by turning the shifting knob or shifting lever The hydraulic drive is activated again when the idle shift is closed position I
52. ly vers diesel engine 14 1 Flat plug fuse at the rear of the ignition lock housing only vers diesel engine agria Hydrostatic Tool Carrier 5900 Taifun Index Amount of Delivery u s 2 Recommendations LUDFRICANIS nee 6 Maintenance and Repair 6 EE 7 Designation Of Pa Susi sa 3 72 76 1 Safety Instructions 7 13 2 Specifications Dimensions aa 14 Wheel combination and Track Widths ET 15 Ee e 16 Petrol Engine 17 18 Diesel Engine anan aa 19 Noise Levels 17 18 19 Vibration Acceleration Value 17 18 19 Operation on Slopes 17 18 19 3 Devices and Operating Elements tee 20 Engine Shut off Switch 21 Ee 21 22 UI 23 gh LO APP po RO E o Renee ne et 23 ITANSMISSION escitas 24 Setting the Driving Speed and Direction 24 Coasting Operation 25 Hydraulic Steering 25 Central Brake narices 26 Steering Handle 26 Loading Bells neunten 27 FIXING Ee 27 Drive Wheels 27 28 A on tit 29 Axle Adjustment 29 Continuous portal axle adjustment 30 Mounting and Dismounting Implements u s 31 BALOT EE 32 33 Seite 32 Ignition lock 34 CONTO lamp Seran 34 agria 4 Commissioning and Operation Commissioning the Machine Start
53. mp Stratton Vanguard Engine agria Hydrostatic Tool Carrier 5900 Taifun Hydraulic hoses A Hydraulic hose B Hydraulic hose agria Hydrostatic Tool Carrier 5900 Taifun 65 Lubrication Chart Petrol Engine agria 8 J yearly amp B always after cleaning with a high pressure cleaner D S sg NY YY AS I XO N 3 O o E SO gt eng e SS Mei ps5 O 1g LI L tz K NPA VA A gt ee WK Se S WA NY WK G du LIN ON Z ANY IN R A 77 7 TI f y 07 d d MO DOAAA YY Y YY y e Ge ee A 66 agria Hydrostatic Tool Carrier 5900 Taifun Lubrication Chart aq ria Diesel Engine 10 11 Eemer O1 O GIS E SA KE TE Q w A E O GS SIR N QU O E fe N h e N A NO CO 7 Ges dE S IN G PN NJ NO LL 5832 26 27 WI NO fo NO Ol 8 J yearly amp B always after cleaning with a high pressure cleaner agria Hydrostatic Tool Carrier 5900 Taifun 67 Inspection and Maintenance Chart aqria Toutes les x h d utilisation A J V rifier le bon fonctionnement de l interrupteur de le bon fonctionnement de V rifier le bon fonctionnement de l interrupteur de de IK Il 56 EE Oe E V rifier le r glage dujeu du tever KILL BR Veriferlefilreaair TIR A Vider le pr ire du Are amp at cyclone IST Has Netioyer a gri
54. n behind the ignition lock and the socket are both secured by a 15 A plug in fuse Ignition lock This plug in fuse B 14 1 is located in the ignition lock housing For access open the cover on the ignition lock housing at the rear with a screwdriver O Socket This plug in fuse is located in the fuse box C 7 in the cable connection from the battery to the socket agria Hydrostatic Tool Carrier 5900 Taifun 33 3 Devices and Operating Elements p g Diesel Engine TI Ignition lock Starter switch 8 14 0 Engine off Engine Stop Operation O Engine starting position when the ignition key is let go it moves back on its own to the position T id Indicator lamps 8 13 green Engine operation in order Ensure that when the engine is running only the green indicator lamp continues to be lit up none of the red lamps may be lit If a red indicator lamp lights up stop the engine immediately look for the cause and clear it Oil pressure indicator red lights up if the engine poil pressure is not in order possibly through a lack of oil dirty oil filter Charge indicator red lights up if the battery charge is not in order connection cable defective fuse defective generator defective Engine temperature indicator red lights up if the temperature limit for the oil or the cylinder head is exceeded engine temperature too high possibly through a lack of oil engine cooling
55. n fuel line or fuel filter Clean injector nozzle or injection line Check pressure Clean fuel line fill fresh fuel Exchange fuel tank cap Drain fuel and fill fresh fuel Clean air filter Clean injector nozzle or injection line Refill engine oil immediately Clean fan grid clean internal cooling fins Clean injector nozzle Re adjust injection pressure Clean air filter agria Hydrostatic Tool Carrier 5900 Taifun Page 49 k x 46 47 x x 40 21 35 71 BM x BM BM BM 61 51 6 Troubleshooting Problem Possible cause Diesel engine does not stop when set to STOP Diesel engine output too low E starter does not Start Ignition lock damaged of engine off cable Solenoid valve not working Air filter clogged Loose cylinder head or damaged gasket Poor compression Battery is empty Fuse is defective Harness E starter damaged E Start Version Petrol Engine E starter does not Start No warning signal sounds when engine stops Warning signal sounds during operation Battery is empty Fuse Is defective Harness E starter damaged Start switch not activated Beeper is defective Fuse is defective Oil pressure switch damaged Harness is damaged Regulator is defective Fuse is defective Oil pressure too low Harness is damaged Regulator is defective Generator is defective Machine in General Clut
56. ng on slopes make sure it is secured by another person using a bar or a rope This person must stay at a higher position than the vehicle and at a safe distance from the attachment at work If possible always work across the slope Starting the Engine on Slopes If the engine comes to a halt while working and re start becomes necessary proceed as follows O Engage parking brake Move clutch lever and safety circuit lever to start position Re start engine If cleaning becomes G necessary during IT operation the engine must be shut off and the ignition key removed for safety reasons agria Hydrostatic Tool Carrier 5900 Taifun 43 5 Maintenance Petrol Engine dia Apart from observing all operating instructions it is also important to pay attention to the following maintenance instructions Please note G Only do all maintenance work with the engine shut off and ZI ignition key disconnected 0 When working on mowing knives wear safety gloves Engine Checking Oil Level O each time you take up operation and after 8 operating hours e only with engine shut off and in hori zontal position e Clean oil dip stick and surrounding parts e Unscrew oil dip stick clean it with a clean cloth and screw it in again Screw out dip stick and read oil level O In case oil level is below lower mark refill engine oil refer to Specifications until oil level reaches lower edge of oil
57. of Parts Fig C Engine B amp S Vanguard 18 HP 22 HP OONODAAWBNHA a Spark plug spark plug connector left Spark plug spark plug connector right Oil filler tube Oil drain plug Engine number Recoil starter cooling air screen Starter handle Oil dip stick Oil filter Fuel filter Oil pressure switch Fuel tank cap Fuel tank Fuel tap Muffler Air filter Choke lever Oil cooler hydraulic Oil cooler engine only 22 HP Battery Starter switch Socket Fuse holder with flat plug fuse agria Hydrostatic Tool Carrier 5900 Taifun Petrol Engine GAS IS 71 agria la 2 7 14 Petrol Engine Designation of Parts Fig C B amp S Vanguard 11 12 19 11 12 a me PA NG mm LE sing ve UY AG CT ge pa ON 1 N SEEN e fi Yr LR mo Co J N D Te P mi PAG OS AAO ON NEW AN 3 IN 5 N ESS ANA E E SAR J SN FRI PENN 5 EX 8 71 se N SE AOS AAA S X AS a7 JAULA E AOR D NA Ae gt E EEN A 2 A NOAH 17 dun CEC A D Ge A D MYO CH E a CC Q AO LOCA TH ech NG HERA e Ai dt E CON Oh Fri S889 A ARO X Hp 188 pi O Ko ALES EY WUE e OSS NCEE Co O SIA Mu WAH age se CX SON WITH O ITNA 3 Q OSAMA 0 N NS WOE Y N SSA WALA pt gt ROZ o Ce WAH 00 NELLY 00 NRL LO ART Q SSS Hydrostatic Tool Carrier 5900 Taifun agria 72 Electrical Wiring agria Petrol Engine bl blue or orange br brown ro red ge yellow sw black gr
58. r 5917 01 Traction cage wheels10 for 5 00 10AS 5917 541 isa Traction cage wheels 12 5 00 12 23x8 5 12 23x10 5 12 Drive wheel attachment and application see page 27 28 16 agria Hydrostatic Tool Carrier 5900 Taifun 2 Specifications agria Petrol Engine 18 HP Rated Speed 3600 rpm Manufacturer BAS Top no load speed 4000 rom Type Vanguard 18 HP 356447 0123 idling FRSE E 1750 rom Version Fan air cooled Engine oil 2 cylinder 4 stroke Filling quantity approx 1 7 l OHV engine petrol Multi grade oil BOTO ui 2 mm a en one gt Ja Ka Stroke 20 mm SAE 1 OW 40 API SE SF or higher Cubic capacity a 570 com at ambient temperature 25 to 15 C Output 13 2 KW 18 hp SAE 9W20 APESE SE or higher at 3600 rpm Lubrication system Max torque 33 Nm at 2600 rom Oil circulation lubrication Oil pressure Spark plug Bosch FR8DC IT the idle run min 0 35 bar CHAMPION RC 12yc Ol Wer een Filter cartridge Spark plug gap 1 0 mm Ignition Electr magnetic ignition contactless AI OAD sonarer eius 0 2 0 3 mm Radio remote screened as per VDE 0879 Valve clearance engine cold Intake and outlet 0 1 0 16 mm SIA HO nia Recoil starter Electrical starter 12V Dale Wai oda 12V 20Ah Generator 12V 192 W PUB cds Commercial petrol min o
59. r bio lubricating grease for open lubricating points or nipples as specified in the operating instructions We recommend using bio anti corrosive oil for preservation of machines and implements do not apply on painted external covers Oil can be brushed or sprayed on Anti corrosive agents are kind to the environment and degrade fast Using ecologically safe bio lubricants and bio anti corrosives you contribute to environmental protection and to the wellbeing of humans animals and plants aqria Maintenance and Repair The trained mechanics of your agria workshop carry out expert maintenance and repair You should only carry out major maintenance work and repairs on your own if you have the proper tools and knowledge of machines and internal combustion engines Do not hammer against the flywheel with a hard object or metal tools as it might crack and shatter in operation causing injuries and damage Only use suitable tools for pulling the flywheel 6 agria Hydrostatic Tool Carrier 5900 Taifun Recommendations Fuel Fuel This engine runs smoothly on commercial unleaded regular and supergrade petrol on leaded supergrade petrol and Aspen 4T petrol Do not add oil to petrol If for environmental reasons you use unleaded petrol make sure the fuel is drained completely when shutting down the engine for more than 30 days This is to prevent resin residues from depositing in the carburetor fuel fi
60. rdance with EN 12733 appendix B Noise level at operators ear Double knife drive L 91 5 dB A Rotary mower 80 L 91 1 dB A Safety Mulcher105 L 92 8 dB A e In accordance with 2000 14 EC appendix Ill part B chapter 32 lawn mower Acoustic power level Double knife drive L 104 2 dB A Rotary mower 80 106 4 dB A Safety Mulcher 105 L 108 8 dB A Vibration acceleration value In accordance with 2002 44 EC and EN 12733 on handlebar grip With Rotary mower Safety Mulcher EE EEN a lt 2 9 M S Double knife drive a 7 60 M S Operability on Slopes Engine is suited for use on slopes with oil level at max upper level mark possible up to 45 inclination 100 agria Hydrostatic Tool Carrier 5900 Taifun 2 Specifications a agria Diesel Engine 25LD425 Rated speed 3600 rpm _ Top no load speed 3800 rpm Manufacturer Lombardini TYPO oo eecccccccecsessseeesssesseeee Pr Ds anne SES Version Fan air cooled EUbrication 2 cylinder 4 stroke engine diesel direct fuel injection BONG ee 85 mm SHOKO ee 75 mm Cubic capacity 851 ccm Compression ratio 19 1 Output 14kW 19 hp at 3600 rpm Max torque 42 Nm at 2200 rom Slao ARA PE PARA Ele
61. ria Steering Handle Locking Bolt A At certain intervals lubricate at the grease nipple with Bio lubricating grease At least once per year and after cleaning with a high pressure cleaner Steering Handle Lock Always after 200 operating hours and always after cleaning with a high pressure cleaner apply some Bio lubricating grease to either side of the rollers A 8 for the steering lock Valve Steering C As from valve steering 15 Always after 100 operating hours and always after cleaning with a high pressure cleaner apply some Bio lubricating grease to either side of the sliding surfaces of the adjustment plate at the steering valve 15 Steering Handle Ultra Bushes Check condition always after 200 operating hours 9 aqria Service Steering Handle Central Screw Always after 200 operating hours re tighten central screw A 9 with 140 Nm and counter it again 2 agria Servicec agria Hydrostatic Tool Carrier 5900 Taifun 5 Maintenance agria Drive Wheels O When commissioning the tool carrier and each time you change wheels check and tighten wheel bolts and nuts after the first 2 operating hours with 100 Nm 10 kom Proceed likewise when doing maintenance work Check tyre air pressure regularly For smooth driving make sure that there is the same pressure in front and rear tyres respectively Wheel Hubs O Always after 50 operating hours retighten the hex nuts A 26 on the wheel hubs to 110
62. ring Steering handle height adjustable side adjustable without tools Oil for transmission and hydrostat optionally e Multi purpose oil SAE 10W 40 API SE SF or higher e Bio hydraulic oil Synthetic ester basis HEES Viscosity as per ISO VG 46 Purity class min 16 13 ISO 4406 e g ARAL Nine Vitam EHF 46 Ee Biohyd SE 46 A HE 46 e Plantohyd S 46 PANOLIN 22222000 HLP Synth 46 Filling volume at First TUNG E abt 7 01 OU CHANGO cascos abt 5 0 I Oil filter Screw type cartridge AW 14 agria Weights vers petrol engine Machine Empty weight with fuel tank filled up without with drive wheels 23x8 5 12 193 5 kg 225 5 kg with portal axle 5939 011 215 5kg 247 5 kg Weights vers diesel engine Empty weight with fuel tank filled up without with drive wheels 23x8 50 12 without portal axle 224 kg 253 kg with portal axle 236 kg 275 kg Tyres 23x8 5 12 wide track field tyre series equipment optionally O19O TAZ ua 5 00 10 field tyre 3490 411 5 00 12 field tyre 3490 511 20x 8 00 10 grass tyre 3490 611 21x11 00 8 terra tyre for this Terra Grip design track width adjusters are required B010 00 EE 2x9cm 5990 711 23x10 5 12 wide track field tyre Tyre air pressure at IA msn 1 5 bar OO EEN 1 5 bar SINIO AAA 0 8 bar 20X8 00 T10 ee 0 8 bar LOMO LE im mme 1 3 bar 28 LOS NA ah a re 1 3 ba
63. t Pneumatic tyres are quickly destroyed if left standing under load and unsuppor ted d Pull clutch Always park tool carrier with clutch lever pulled pawl locked in place Otherwise clutch problems may result due to e Parking To avoid severe corrosion to preserve the machine from at mosperic influences do not park the ma chine in humid rooms in rooms where fertilizer is stored in stables or adja cent rooms f Covering the machine Protect the machine with cloth or a simi lar cover 59 6 Troubleshooting A Problem Possible cause Petrol engine Petrol engine does not start Misfirings in petrol engine Excessive temperature in petrol engine Misfirings in petrol engine at high speeds Petrol engine frequently Stalls in idle 60 Spark plug connector not connected Choke is not operated Engine shut off switch is set to 0 Safety circuit is not set to start position Fuel tank empty or poor fuel Fuel line clogged Defective spark plug Engine too much fuel flooded engine Engine off line defective Inleaked air due to loose caburetor and suction line Engine running in CHOKE range Loose ignition cable Clogged fuel line or poor fuel Vent opening in fuel tank cap clogged Water or dirt in fuel system Air filter clogged Carburetor misadjusted Low engine oil level Impaired cooling Air
64. tween the regulator and electric starter to protect the regulator and generator from a short circuit induced from outside Replace the fuse if it is defective To do this open the fuse holder take out the battery beforehand ensure to provide another spare fuse in time 32 agria Hydrostatic Tool Carrier 5900 Taifun 3 Devices and Operating Elements Never leave battery in un A charged state Avoid sparking and open flames near batteries Careful when handling battery acid etching Only use specified fuses If fuses are too strong the electric system will be destroyed danger of fire OOO ooo A B 14 1 Diesel Engine AQnid Battery C 6 gt Note manufacturer s instructions The battery is supplied filled with acid of a density of 1 28 g ml and is loaded and ready to operate If it gives insufficient power to start re charge recommended charging current 1 10 A of the battery capacity Ah The engine can only be started when the battery is connected and in full working order Storing battery load battery store in a cool place or remove 3 vehicle negative clamp Check state of charge regularly and where necessary correct by re charging 57 Disposal Give up used batteries at the collection point store and transport in an upright position secure against tilting so that no acid can leak Never dispose of the battery in household waste Fuse The connectio
65. ulic system render the latter pressureless and shut down engine specialized workshop When searching leakages use suitable aids considering the risk of injuries specialized workshop Regularly check hydraulic hose lines for damage and ageing and replace them if necessary Only use original agria hydraulic hoses Tyres and Tyre Air Pressure When working on wheels make sure tool carrier is parked properly and secured against rolling off Any repairs are to be carried out by trained mechanics only and with the appropriate tools Regularly check tyre air pressure Excessive pressure may cause bursts agria Hydrostatic Tool Carrier 5900 Taifun 1 Safety Instructions Use appropriate tyre air pressure for operation with implements Re tighten attachment bolts of drive wheels or check tightness when doing maintenance work Electrical System and Battery When working on the electrical system make sure the battery is disconnected negative pole for tool carriers equipped with battery Make sure to connect battery properly first connect positive pole and then negative pole Disconnect in reverse order Be careful with battery gases explosi ve Avoid spark discharge and open flames near batteries Remove plastic cover if included to recharge battery to prevent highly ex plosive gases from building up Be careful when handling battery acid Only use specified fuses Stronger fuses w
66. upper level mark CONTINUOUS operation up to 25 inclination Alternating operation for a short period ida up to 35 inclination Specifications for engine see sepa rate operating instructions for Lombardini engine 19 3 Devices and Operating Elements The tool carrier agria type 5900 Taifun is a base power machine and is always operated with an implement mounted Therefore the machine is suited for all common applications in farming and forestry as well as for winter service Available implements e Front implements for mowing sweeping snow clearing and tilling gravel and salt spreading For a choice of further attachments refer to our price list Engine e The four stroke petrol engine runs on commercial petrol refer to fuel recommendations p7 Ignition System The engine is equipped with a contactless ignition system We recommend to have necessary check ups done by an expert only During the first 20 operating hours break in period do not use engine to maximum power Even after break in period never use engine at higher speed than necessary for the work in hand e The four stroke diesel engine runs on commrcial diesel fuel refer to fuel recommendations p7 See to using proper fuel in winter During the first 50 operating hours break in period do not use engine to maximum power Even after break in period never use engine at higher
67. witch to 0 to turn engine off For parking the machine for longer periods of no operation do not use engine shut off switch to shut off engine but close fuel tap and let engine run until it slowly comes to a complete stop This ensures carburetor to be empty and no resin residue to deposit 38 agria Hydrostatic Tool Carrier 5900 Taifun 4 Commissioning and Operation e p Diesel Engine QT Before starting the Engine O sufficient fuel is filled into the tank Air filter clean gt Check the engine oil level O Check transmission oil level 52 Check all bolts and nuts for tight fit 58 Only take machine into opera A tion with all protective devices mounted and positioned to provide protection Careful when starting the engine in closed rooms Ensure good ventilation and fast escape of exhaust fumes Exhaust fumes contain carbon monoxide which acts toxic when inhaled Do not touch the hot engine danger of burns agria Hydrostatic Tool Carrier 5900 Taifun 39 4 Commissioning and Operation e p Diesel Engine QE Starting Diesel Engine also see operating instructions for Lombardini engine O Set speed control lever B 9 to half speed 50 O Set safety circuit lever B 4 and clutch lever B 5 to start position insert key into ignition start switch and turn right to position T O Turn ignition key further to the right to position START

Hydrostatic Tool Carrier 5900 Taifun Operating Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents