Operating Instructions - MAMA
Contents
1. T 787 9e From Fault Code 33 e Beginning with operating mode OFF LED1 all 5 LED light up shortly one after another named as run light 1 x e fault code flashes during 6 sec operating mode is displayed during 10 sec The table shows the run light followed by the LED combination code of the indi vidual faults Fault Display flashing LED 1x 43 45 49 e ojojo y4 e e y4 e jo y4 e e y4 s T787m1e Operating Instructions SLIDEDOOR T 787e 21 Explanation of Fault Code and Trouble Shooting NOOO FR WD 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 43 45 49 Door lock faulty gt possibly intervene by manual lock disengagement Calibration run gt wait until door is closed Battery operation mains failed Light beam 1 faulty Light beam 2 faulty Light beam 3 faulty Light beam 4 faulty possible reasons transmitter receiver cable or power module faulty e safety beam not properly aligned cable not properly shielded In operating mode OFF safety beam interrupted longer than 10 sec Operator type not defined or processor failure Emergency off is activated gt reset push button and select operating mode OFF Motor overheated gt call for assistance Power module faulty or shut down No movement encoder cable motor or belt faulty possi2. Emergency Off Function Check e Activate the emergency off a push button The door is switched to manu al operation and the door leaves 7 can be moved manually If the system is equipped with a emer ren gency opening facility rubber spring the door leaves will open e Reset emergency off push button and choose operating mode OFF The door reacts the same way as on power on Emergency Opening Emergency Opening Monitoring System Rubber Spring Check e Simulate a mains failure disconnect mains plug or switch off main system switch the door leaves should be opening independent of the selected operating mode The rubber spring must be replaced during the annually maintenance see section 5 1 thus after a serviceable time of one year Do not increase the tension of the rubber spring after this time this could lead to excess elongation Checking the System for Traces of Excessive Wear Check Check the system for traces of wear If there are excessive deposits of rubber toothed belt steel or aluminium door wing drive support on the ground around the system contact a qualified TORMAX dealer so that the system may be given a thorough check Operating Instructions SLIDEDOOR T 787e 19 6 Trouble Shooting The microprocessor control system TCP 101 performs a self diagnosis continually and displays faults by means of periodically flashing combinations of LEDs
3. all other operator types IP 22 Ambient temperature range 20 C to 40 C Designation of drive CE TUVUL cUL only TEP TLP and TSP with respective certificate Equivalent continuous sound level lt 70 dB A 7 2 Warranty Deliberate or malicious damaging of system components and staining of system parts as well as alterations to the drive or control system by a third party will result in the loss of all warranty 7 3 Options The following options are available within others e Electromagnetic lock four point lock manual disengagement night duty lock e Emergency power supply emergency opening closing facility emergency opening monitoring system e Panel lock various activators people counter interface to a building facility man agement system Additional functions are programmable e g bell contact hold up locking code lock etc please contact your TORMAX dealer 7 4 Disposal At the end of its useful lifetime this system is to be disposed of according to the relevant national regulations We recommend that you contact a company special izing in waste disposal The contents of this manual are subject to technical changes Operating Instructions SLIDEDOOR T 787e 23 kk IK TO R M AX Your first Choice in Door Automation AUTOMATIC TORMAX SLIDEDOOR TORMAX SWINGDOOR TORMAX FOLDDOOR TORMAX REVOLVEDOOR Manufacturer Consultation sales installation repair and service TORMAX CH 8180 B lach
4. key switches hand switches etc 8 Operating Instructions SLIDEDOOR T 787e Motion detector self checking safety Key switch Control panel eos _ eny Hand switch Push button outside ar a _ Safety beams ee ne e N ee s 2 necking Safa mS Emergency off button e EEE a interior Normal Operating Mode AUTO Function If an opening activator is activated the door opens stops for the duration of the hold open time and closes again If the motion detector or a safety beam scanner recognizes a person while the door is open it remains open If a person moves within the range of the motion detector in direction of the closing door the door reopens immediately The door system may only be operated if all safety relevant devices see section 2 3 are installed and functional Monitoring The TORMAX TCP control systems supervise numerous functions of the door and display malfunctions on the control panel see Fault Diagnosis Diagram in section 6 2 Shutdown in Case of Fault The door must be placed out of operation whenever malfunctions occur that may influence the safety of people Make sure that faults and deficiencies are eliminated at once Doors may be returned to service only after the malfunctions have been corrected repaired o
5. Z rich Phone 41 0 44 863 51 11 Fax 41 0 44 861 14 74 Homepage www tormax com E Mail info tormax com TORMAX is a division and a registered trademark of Landert Motoren AG
6. and understood the operating instructions prior to performing any work Mechanical and electrical work on the door system and the control system may only be performed by our trained specialists or by fitters after consulting our trained spe cialists All other persons are prohibited from performing any repairs or alterations on the system Labels Notices on doors and control devices must be easily legible clearly understandable and of durable quality If instructions are necessary for assuring the safety of people marking of escape routes and for servicing these instructions must be provided on the system 2 3 Safety Devices Self Checking Safety Beams Light Scanners In accordance with an accomplished risk analysis TORMAX allows for correspond ing safety facilities in conjunction with the control system for this operator type for the protection of people and damage prevention to property These facilities must correspond to the current state of technology and comply with the Machinery Direc tive 98 37 EC the CEN and CENELEC standards as well as the corresponding state specific regulations TORMAX allows for the installation of max 2 self monitoring light beams in the doorframe or 2 presence sensors for optimal safety Function Every interruption of the light beam of a photocell or scanner causes the immediate termination of a closing action If after 1 minute the light beam is still interrupted for example on a faul
7. mode can be avoided Example 1 The AUTO mode has been selected Now the door is to remain fully open e Press the DOWN key in brief succession 3 times gt the door opens completely after approximately one second If after pressing the DOWN key once you wait longer than one second before press ing the key repeatedly until the OPEN mode is reached then the AUTORED mode is activated during the interval and the door will stay open at reduced opening width Example 2 The OFF mode is active and the door is closed The closing speed is to be changed without opening the door e Press the DOWN key four times in rapid succession and then immediately press both keys simultaneously for one second e Adjust closing speed as described in section 4 2 After the input press both keys again for one second gt now the LED OFF lights up again indicating that the operating mode has not been changed during the adjustment process Operating Instructions SLIDEDOOR T 787e 15 5 Maintenance The responsibilities of maintenance personnel must be clearly defined AN Keep hands and other body parts away from moving devices Spare parts must comply with the technical requirements of the manufacturer Use genuine spare parts exclusively 5 1 Periodic Maintenance Maintenance Interval The maintenance interval is determined under consideration of the frequency of use of the system However checking and maintenance must be performe
8. on the control panel For fault analysis and fault removal proceed according to the following fault diagnosis diagrams 6 1 Fault Diagnosis Diagram 1 Check control panel Electric mains is interrupted Fuse blown or Code lock is active enter code Is any LED lit up at the control Trigger software reset Fault occurs again see fault diagnosis diagram 2 Can you change the operating mode Panel lock is active or Code lock is active Yes Door system or auxiliary devices gt faulty T 787 8e 20 Operating Instructions SLIDEDOOR T 787e 6 2 Fault Diagnosis Diagram 2 With the occurrence of a fault the corresponding fault code is displayed on the control panel in flashing LED combinations form alternately with the display of the active operating mode Fault Code 1 to 30 e Fault code flashes during 6 sec operating mode is displayed during 10 sec The table shows the LED combinations code of the individual faults flashing LED 12345 67 8 9 10111213 14 15 1617 18 19 20 21 22 23 24 25 26 27 28 29 30 ae lt e e jo o o je o e o o o je o Je jo axe ejo ejo ele e ele ejo ele e exm lt RMX oojoo o ojojo elelele ojojo om _ oojo ojojo ojo e ojojo ojo oi V e o o ojo ojo ojojo ojo oj ojo
9. ans of the rubber spring installed into the operator opening emergency open ing or closing of the door leaves emergency closing on mains failure are en sured Operating Instructions SLIDEDOOR T 787e 5 2 Safety 2 1 General Safety and Accident Prevention Regulations Please read the operating instructions carefully prior to installation or commission AN ing especially the following notes relating to safety and adhere to them at all times Damage to the unit and personal injury may result if these instructions were not carefully followed Pay particular attention to the specially marked notes in this manual for an explana tion of the symbols please refer to chapter 1 TEP TLP and TSP Sliding Door Operators with UL cUL Certificate These products are Underwriters Laboratories Inc UL listed and cUL certified for the Canadian marketplace and therefore comply with the requirements of the Na tional Electrical Code NEC and the Canadian Electrical Code CEC Installations intended to meet UL and cUL requirements must be followed as described in the instruction provided herein These are minimum standard requirements Where local codes exceed these requirements they must be followed as well Preventing General Hazards and Possible Damage to This Equip ment Keep fingers away from all moving parts e Verify that the power selection switch is set to the correct voltage before start up e The power supply cable flexib
10. bly door blocked Battery failure or signalling device faulty Failure of night duty lock gt possibly intervene by manual lock disengagement Door in reversing mode door encountered an obstacle gt wait until door is closed Panel key UP gives contact longer than 1 min panel or cable faulty Panel key DOWN gives contact longer than 1 min panel or cable faulty Burglary alarm gt reset by means of key switch or system reset Activator 1 gives contact longer than 1 min Activator 2 gives contact longer than 1 min Activator 3 gives contact longer than 1 min Activator 4 gives contact longer than 1 min possible reason e activator or cable faulty Safety beam 1 interrupted for more than 1 min Safety beam 2 interrupted for more than 1 min Safety beam 3 interrupted for more than 1 min Safety beam 4 interrupted for more than 1 min possible reasons safety beam or cable faulty optical components possibly dirty Key switch gives contact longer than 1 min possibly key turned External closing reversing External opening reversing Free wheeling mode Support request system needs maintenance gt call for assistance System is ready for automatic system configuration 22 Operating Instructions SLIDEDOOR T 787 e 7 Additional Notes 7 4 Technical Data Mains voltage 115VAC 108 125 V 230 VAC 198 264 V Frequency 50 60 Hz Power consumption min max TPC 51 51LC 4 W 160 W TCP 101 14W 240 W Protective class TEPIP65 IP 65
11. d at least once a year by an authorized technician Requirements Concerning Maintenance Personnel Authorized technicians are persons who have adequate knowledge in the discipline of power operated doors based on their vocational training and experience and who are acquainted with the relevant accident prevention regulations guidelines and generally recognized rules of that technology to such an extent that they can ap praise the safe working condition of power operated doors These persons include for example authorized technicians of the manufacturing or supplying company and experienced technicians of the system operator Authorized technicians have to submit their expertise objectively from the point of view of accident prevention and not influenced by other e g financial perspec tives Maintenance work on electrical parts and cables must be performed by an electrical fitter who must work in accordance with the relevant regulations system either by unplugging the mains plug or through securing the main system For all work a clear separation must be created between mains supply and drive AN switch in position off Extent of Maintenance Work The extent of maintenance work is shown in the System Test Book The inspection results are to be entered in the System Test Book by the authorized technician together with date and signature 16 Operating Instructions SLIDEDOOR T 787 e gt gt 5 2 Inspections by the System Operato
12. document has validity for automatic TORMAX door systems with TCP control systems of types TCP 51 TCP 51LC or TCP 101 This concerns to the following door systems with control system TCP 51 Drive TEP Drive TEP IP65 Drive TKP Drive TSP Drive TOP with control system TCP 51LC Drive TLP with control system TCP 101 Drive TXP Explanation of Symbols In these instructions we have designated all passages concerning your safety with this symbol This symbol warns of electrical voltage Text passages in grey background must be absolutely observed for sound op eration of the system Disregard may cause material damage Operating functions that are marked by the accompanying symbol correspond to the basic settings however the fitter can reprogram them This symbol marks optional components which are not installed in all systems Languages These instructions are available in various languages Please ask your TORMAX dealer Applicable Documents Please refer also to the system test book which contains a list of checks that need to be performed during the periodic maintenance see also section 5 1 The system test book is located at the corresponding door system System test T 879 e Operating Instructions SLIDEDOOR T 787e 3 Warnings of Dangerous Electrical Voltages or Current e Be sure the electrical power is disconnected and locked out when working on the operator unit e Install the electrical cables and power only a
13. fter the mechanical installation to the unit is done Turn on the power to the operator unit only after all internal cables are connected Do not connect cables while the unit is powered e Always use appropriate tools for installation and repair Correct Application The TORMAX operator has been designed and manufactured according to the state of the art engineering and the recognized safety related regulations and is intended exclusively for the operation of automatic TORMAX doors Operators corresponding to IP 22 in the protective system may only be installed at the inside of buildings if no additional protective measures are provided Any other use is considered non permissible and may result in injuries to the user or third parties The manufacturer will not be liable for damages resulting from incor rect application The risk of such non permissible applications must be borne solely and entirely by the operator of the door system Basic Precautionary Measures Careful Behaviour Do not use the system in other than technically perfect condition Make sure that faults which could impair safety are eliminated immediately by professionals The following are consequences of incorrect application of the door operator or the door system Danger of the user s or a third party s injury or loss of life e Risk of damage to the system or associated equipment Relevant Instructions The operating service and maintenance conditions
14. ing of the door The door must not close too early l T 787 2 T 787 3 Operating Instructions SLIDEDOOR T 787e 17 A Check e Approach the door slowly side ways along the door leaves The door must open T 787 4 Manually Operated Opening Activators Push Button Key Switch Check e Initiate corresponding activator briefly The door opens and recloses after the set hold open time has elapsed e Initiate opening activator for around 20 sec C gt i T 787 1 The door opens and stays open When the impulse is released the door closes only after the hold open time has elapsed Checking the Safety Devices Safety Beams Light Scanner Check e Interrupt the light beam by hand When the door is open it should not close during at least 1 min If the door is closing it must immediately reopen Electronic Reversing Check 1787 5 e Place an obstacle sponge rubber block or similar between the door wings with out interrupting the safety beams or light scanners When the door encounters an obstacle it reopens the overrun distance in the area subject to jamming is max 25 mm When the prolonged hold open time has elapsed the door closes but at reduced speed 18 Operating Instructions SLIDEDOOR_ T 787e A a N D gt 40cm A
15. le cord should be entered at the end side that is close to the input power supply plug It should not be routed through doorways window openings walls ceilings floors etc The power supply cable flexible cord should not be attached or otherwise secured to the building structure It should not also be concealed behind walls etc e Never allow the power supply cable flexible cord to become entrapped in moving parts of the operator door or system The power receptacle must be of the grounding type It is very important that the unit will be properly grounded e To reduce the risk of electrical shock this equipment has a grounding type plug that has a third grounding pin This plug will only fit into a grounding type outlet If the plug does not fit into the outlet contact a qualified electrician to install the proper outlet Do not change the plug in any way 6 Operating Instructions SLIDEDOOR T 787e 2 2 Organizational Measures Doors are to be operated and maintained in such a way that the safety of the user maintenance personnel or third party is guaranteed at all times Should any fault occur on the safety devices i e safety beams they may not be bypassed to maintain the automatic door functions Working on TORMAX Door Systems The person operating checking or maintaining door systems must have the relevant operating instructions present Personnel charged with duties on the door system must have read
16. ng mode AUTO Tr Time reduced Hold open time with reduced opening width active in operating mode AUTORED The hold open time is to be set so that even slower users have enough time to pass through the door On the other hand the hold open time is to be kept short in order to minimize energy loss in winter Significance of Indications Limit Values UP key faster flashing shorter hold open time minimum 0 sec DOWN key slower flashing longer hold open time maximum 10 sec Operating Instructions SLIDEDOOR T 787e 13 Reduced Opening Width Pr Pr Position reduced Position of the open door with reduced opening width operating mode AUTORED If energy loss is to be minimized in winter or if for other reasons a reduced opening width is desired it is infinitely variable between a minimum of 20 cm per leaf and the full opening width Significance of Indications UP key faster flashing gt smaller opening width DOWN key slower flashing wider opening width If the operating mode AUTORED is set before the optimization of the reduced open ing width the door leaves move to the desired opening width simultaneously with the variation in the rhythm of flashing Speeds Vo and Vc Vo Velocity open Opening speed Vc Velocity close Closing speed Depending on the weight of the door a reduced speed is necessary in the closing direction the regulations in the relevant country must be observed in order t
17. o minimise hazards to persons If necessary the speed is limited or the parameter is blocked by the installation engineer i Normally a high opening speed is desired to avoid slowing down the flow of people Significance of Indications UP key faster flashing higher speed DOWN key slower flashing lower speed Limit Values Speed per leaf cm sec TEP TLP TXP TRI A TOP TSP TKP Opening Minimum 30 30 30 30 Maximum 80 80 80 70 Closing Minimum 20 20 20 20 Maximum 50 50 50 50 14 Operating Instructions SLIDEDOOR T 787 e 4 3 Specifics of Operation Code Lock The control panel can be protected against unauthorized manipulation by means of a code lock Changing Operating Mode or a Parameter Setting When Code Lock is Active Enter code preprogrammed by the authorized technician This may be the standard code 3 x UP 3 x DOWN 3 x UP or a user specific code e Immediately adjust desired settings This is only possible during a limited period of time after this time has elapsed the LEDs are automatically switched off and the control panel is interlocked again Skipping Operating Modes The desired mode is selected by pressing the UP or DOWN key once or multiple times The respective LED lights up immediately the operating mode however be comes active only after one second Thus by pressing the key rapidly in succession the undesired activation of an operating
18. oor into operation again press one of the keys UP or DOWN for 5 seconds or e Activate emergency off gt the door leaf can now be moved manually at the control panel fault code 10 is indicated see section 6 2 To put the door into operation again reset emergency off button and select op eration mode OFF or e Disconnect mains plug gt the door is brought to a halt by braking afterwards the leaves can be moved manually Software Reset Calibration Run Triggering a reset of the door control system e Press one of the keys UP or DOWN of the control panel for 5 seconds gt the door executes a calibration run the control system moves the door leaves slowly to open position to find the end stops after the hold open time has elapsed the door closes again During this procedure the fault code 2 is indicated at the control panel see section 6 2 10 Operating Instructions SLIDEDOOR_ T 787e 4 Control Panel Operation The most important element for the system operator is the TORMAX control panel with the following options e Selection of operating mode determines the behaviour of the door gt section 4 1 e Setting of parameters optimizing the motion process gt section 4 2 e Code lock control panel interlock gt section 4 3 e Manual operation free wheeling gt section 3 4 e Reset calibration run gt section 3 4 e Fault indication flashing LED gt chapter 6 Some functions may be inhibited o
19. r Extent of Inspections The inspection must be performed periodically but not less than once every 3 months The system operator of an automatic door has to periodically check the functioning of the automatic door and the safety devices Thus an early recogni tion of functional faults or of mutations to the system that diminish safety is ensured If deficiencies are found during the periodic checks ensure that these are repaired immediately by an authorized TORMAX dealer address see at back of these instruc tions When performing these inspections consider always the possibility of a malfunction of the system No parts of the body may be used for functional checks if there is not enough free space available instead use as a substitute a suitable object from wood rubber or similar material The maintenance work to be performed by the system operator requires only a minimum of time but is essential for the safe and faultless functioning of the system This work include Checking the Opening Activators Select operating mode AUTO Automatically Operated Opening Activators Radar or Infrared Motion Detector Contact Mats etc Check Hi 4 e Passing through the door in a normal manner M The door opens and recloses et when the set hold open time has elapsed Check Slow approach appropriate to an IN 4 EEE elderly person pause for around 5 sec before reaching the door Normal open
20. r limited due to door specific adjustments per formed by the authorized technician Control Panel Symbol for operating mode LED Door parameter Operating Mode aN Lf Door closed and locked OFF ia se P hur Automatic operation AUTO 4a X m lt To Automatic operation with 3 reduced opening width AUTORED 4 m m lt Shop closing mode EXIT lt 4 Q m lt ys DOWN Door remains open OPEN lt T 787 30e TORMAX Pr TORMAX OMATIE Door Parameter Tr Hold open time with reduced opening width To Hold open time with full opening width Pr Reduced opening width Vo Opening speed Vc Closing speed Operating Instructions SLIDEDOOR T 787e 11 4 1 Selecting Operating Modes Setting Operating Mode The continuously illuminated LED indicates the currently active operating mode e Press UP or DOWN key till desired operating mode is indicated on the panel An operating mode is only valid if the LED has been lit up for at least 1 second Operating Mode OFF Door closed and locked In the operating mode OFF the door is closed and cannot be opened by the opening activators except by a key switch The door leaves are blocked and also locked if a lock is fitted The opening activators will immediately be deactivated if the operating mode OFF H is selected while the door is still open However safety beams and light scanners remain functional which ensures that the door will not close if a person is within
21. r the hazard eliminated e g set operating mode to OPEN or separate operator from mains supply The escape function of doors serving as emergency exits must not be impaired Damage Components that no longer ensure the required safety standard due to wear or tear must be replaced or repaired by a qualified TORMAX dealer Operating Instructions SLIDEDOOR T 787e 9 3 3 Operation in Case of Mains Failure On mains failure the door is brought to a halt by braking afterwards the leaves can be moved manually Emergency Opening Emergency Closing Opening emergency opening or closing emergency closing of the door leaves on mains failure are ensured by storing mechanical energy rubber spring installed into the drive unit Battery Module The emergency power supply permits continual operation of our automatic doors during a limited time On power recovery the system switches immediately back to mains operation and the batteries are recharged again For more detailed information see Operating Instructions of your battery module 3 4 Manual Operation and Software Reset Manual Operation Free Wheeling There are several feasibilities if by way of exception the door should be moved manually e Press one of the keys UP or DOWN of the control panel for 10 seconds gt the automatic operation is then switched off and the door can be moved freely at the control panel fault code 43 is indicated see section 6 2 To put the d
22. set to default values when the system is commissioned It can however at any time be adapted to individual requirements The parameters are shown on the control panel by letter pairs Tr To Pr Vo Vc With each parameter detailed description see later on a specific door behaviour can be optimized Select parameter Tr To Pr Vo or Vc to be adjusted by means of UP or DOWN key corresponding LED lights up e Press both keys UP DOWN simultaneously for one second gt the LED flashes to indicate that the optimization can be performed e Adjust respective parameter by pressing the UP or the DOWN key once or sev eral times If for example the movement is to be faster the UP key is pressed The flashing frequency as well changes accordingly e If no key is pressed within 60 seconds the adjustment process is terminated automatically and the settings remain unchanged e To store the new parameter setting press both keys UP DOWN again simultane ously gt now the LED is again continuously illuminated The new setting is now in effect All other settings e g acceleration and braking distances are optimized by the mi croprocessor and may only be changed by authorized technicians Hold Open Times To and Tr The hold open time is the time during which the door stays in the open position from the time the sensors no longer receive any signals To Time open Hold open time with full opening width active in operati
23. specified by the manufacturer are to be observed TORMAX drive units must only be maintained and repaired by trained specialists who are aware of any possible danger that may occur In addition to the operating instructions the generally accepted legal and otherwise relevant rules relating to accident prevention and to occupational medicine in the country where the door system is installed are also applicable The manufacturer is exempted from any liability for damages caused by unauthorized alterations of the system 4 Operating Instructions SLIDEDOOR T 787e Electronic Reversing During the opening and closing actions the door movements are monitored by a sensitive electronic circuit Function If the door hits an obstacle during closing then it reopens remains open somewhat longer and closes again with reduced speed If the door hits an obstacle during opening it reverses and runs in closing direction for a few cm stops for a while and closes with reduced speed The door will open if an activator is in operation Emergency Off Function installation according to local regulations Function The activation of the emergency off button causes an immediate stop of the door The door leaf can then be moved manually at the control panel fault code 10 is in dicated see section 6 2 until the emergency off push button is reset and the oper ating mode OFF is selected Emergency Opening Emergency Closing Function By me
24. t then the door continues to operate in a safety mode that is with a slow closing speed Operating Instructions SLIDEDOOR T 787e 7 3 Operation 3 1 Commissioning Switching On e Switch on mains supply mains plug or main system switch At the control panel PANECO press key UP or DOWN to select the desired oper ating mode the corresponding LED lights up If the door is locked or in the operating mode OFF the door presses briefly against the close position In any other operating mode the door performs a calibration run to find the end stops The LED AUTO flashes during this process o 1 OFF ae lt i uP AUTO ecm 3 TORMAX AUTORED 4m em lt TORMAX EXIT 4 Q lt 5 Vv DOWN OPEN 4 gt lt T 787 30e Re Commissioning If the door has not been operated for a longer period it must be checked prior to re commissioning according to section 5 2 and repaired if necessary so that the safety of people is ensured at all times 3 2 Normal Duty Operation The TORMAX door operator ensures the automatic opening and closing of the door By selecting an operating mode at the control panel the behaviour of the door can be affected by the system operator Activation The activation of the door takes place through opening activators automatically or manually e Automatically by means of sensors motion detectors contact mats etc e Manually by means of push buttons
25. tO KIO TORMAX AUTOMATIC Operating Instructions for Automatic TORMAX Doors with Control System TCP 51 TCP 51LC or TCP 101 Table of contents 1 2 2 1 2 2 2 3 3 3 1 3 2 3 3 3 4 4 4 1 4 2 4 3 5 Introduction Safety General Safety and Accident Prevention Regulations Organizational Measures Safety Devices Operation Commissioning Normal Duty Operation Operation in Case of Mains Failure Manual Operation and Software Reset Control Panel Operation Selecting Operating Modes Optimizing the Course of Motion Specifics of Operation Maintenance 5 1 Periodic Maintenance 5 2 6 6 1 6 2 7 7 1 7 2 7 3 7 4 Inspections by the System Operator Trouble Shooting Fault Diagnosis Diagram 1 Fault Diagnosis Diagram 2 Additional Notes Technical Data Warranty Options Disposal First Edition 3 92 Update 6 94 8 96 11 97 4 99 10 00 3 05 We are printing on environment friendly paper bleached without chlorine The companies Landert Motoren AG and Landert GmbH are certified according to ISO 9001 2 Operating Instructions SLIDEDOOR T 787 e gt gt FE 1 Introduction Addressee Status The following instructions are directed at the system operator and user of an auto matic TORMAX door system It is assumed that the system was installed and tested by professional persons i e it is ready for operation Applicability This
26. their range Operating Mode AUTO Automatic operation AUTO is the main operating mode Upon a door opening command the door opens automatically to full opening width stays open until the hold open time To has elapsed and closes again Operating Mode AUTORED Automatic operation with reduced opening width This mode is useful in winter to reduce loss of energy In operating mode AUTORED upon a door opening command the door opens au tomatically to a reduced opening width stays open for the hold open time Tr and then closes again If a sensor detects a person approaching from the opposite direction during opening the door opens a little wider to provide passing space for people cross traffic Operating Mode EXIT Shop closing mode In this mode the door opens only through the motion detectors fitted inside the build La ing However as long as the door is not fully closed the external motion detector causes also a reversal of the door movement The opening width depends on the previously selected operating mode AUTO or AUTORED Operating Mode OPEN Door remains open The door opens immediately and stays open The opening width depends on the previously selected operating mode AUTO or AUTORED 12 Operating Instructions SLIDEDOOR_ T 787 e 4 2 Optimizing the Course of Motion Adjusting Parameters The door parameters and therefore the course of motion is automatically
Download Pdf Manuals
Related Search