[ Installation Manual ]
Contents
1. MODEL HEAT300 Installation Manual Contents AA AA AA AAP Features AA ANA AA NG Safety Instructions mana a anuna waa naaawa ana 14 Drawing ama aiai 7 Place for Personal Notes 1112sssss s1 1 2015 AMPIRE Electronics All rights reserved Ad Shipment e Universal heating elements 2x e Wire harness with relay e Switch 1 2 3 OFF with LED e Fuse holder with fuse e 4pcs of double side adhesive tape for installation e Installation manual and accessories e Black Mass Car Body e Red 12V KI 30 Charging Rate 5A e Yellow Ignition KI 15 e Grey Headlight 2015 AMPIRE Electronics All rights reserved Features e Set for 1 seat e Fast and steady heating elements e Heating elements for any seat geometry e Suitable for cloth and leather seat cover e 3 heating levels 30 C 35 C 40 C e Thermostat controlled system e Thermal protection e Installation under seat cloth or leather e Power supply 12VDC 5A max e Dimensions of heating elements 475 x 255mm D x W e Complete set incl switches and wire harness 2015 AM PIKE Electronics All rights reserved pr ay Safety Instructions 01 Pay utmost attention to this safety instruction to avoid damages or accidents with serious even life threatening injuries evoked by fires or electric shocks The installation has to be done by authorized workshops onl2. ditionally insulated Isolate the edges of cutouts with fabric adhesive tape Never cut the electrode while making a cutout be sure to keep a minimum space of 40 mm Page 17 Fig 2 Normally carbon fibers overlap a few millimetres besides heating mats avoid contact with any electroconductive seat components Take especially care of lateral metal wiring Apply the heating elements e g capable spray on glue without crinkles and fix well otherwise exists fire risk 15 See that heating elements not becomes damaged during installation as could be caused by pilot tools hog rings or seat frames 16 Before applying the heating mats the foam body has to be free of fat oil and silicone You receive full adhesive strength by sufficient surface pressure and curing time Normally it takes several hours Once installed don t remove the heating mats for re installation 17 Pay attention while running the cable to fix it carefully so that seats can be moved without problems the whole way 18 Avoid damaging cable isolation by sharp edges kinking or tensile stress Fig 1 19 Note down evading memory codes e g radio navigation and then disconnect battery before start working on the electrical system 20 Depending on seat and cover material the temperature varies on seat surface 21 In cases of failure or breakdown please control safety fuse first Fig 2 22 Explain function and instruct on safety befor
3. e handing over the customers car 2015 AMPIRE Electronics All rights reserved 2015 AMPIE Electronics All rights reserved 2015 AMPIRE Electronics All rights reserved 2015 AMPIRE ELECTRONICS All rights reserved Reprint is only permitted with a written authorization
4. y 02 Begin with checking if installation is possible a Installation is complex if not impossible with adhesive upholstered seats b Installation is not possible on seats with longitudinal ditches c Installation is not possible on seat with a central area width less than 270 mm edges have to end in front of lateral ditches 03 For installation on seats with occupation recognition follow instructions of vehicle manufacturer 04 For installation on seats with belt tightener follow instructions of vehicle manufacturer 05 For installation on seats with side airbags in backrest follow instructions of vehicle manufacturer a Seat cover and its seams have to stay unchanged 2015 AM PFIRE Electronics All rights reserved 06 07 08 09 10 11 12 13 14 2015 AM PIKE Electronics All rights reserved b Mount heating mat only on the central area of foam body Control connection scheme for checking that electrical system and wire cross section are suitable for additive current load Search a practical place for switches Use only original components included in delivery Never change width by cutting the mats long ways cut off only as shown Page 17 Fig 1 You can feet the mats through crosswise ditches but edges of cutouts have to end in front of these Heating mat must not contact any electroconductive seat components such as hog rings and seat frame unless it is ad
Download Pdf Manuals
Related Search