User's Manual ETLOC-30 - 5 - pro DUCASE
Contents
1. 12 Red white 12V backup power source Yellow red and black wires must be always connected Connection of remaining wires is optional In case particular wires are not connected relevant functions of the system will not be active The output of external alarm can be connected to input of the GPS locator using white or orange cable AQ white cable INPUT alarm is activated by signal OV A1 orange cable INPUT alarm is activated by signal 12V The maximum current carrying capacity of the switching relay is 12V DC 5A While controlling an appliance with a higher current load use an auxiliary relay with appropriate technical parameters 3 Connect the GPS antenna and the cable connector to the unit GPS antenna must be placed horizontally and must not be obstructed from the top by metal parts 4 Switch car ignition ON and OFF The unit is ON now Wait approximately 2 minutes for the unit initialization completion The unit is ready to receive configuration SMS commands after that time Note The GPS locator allows connection of backup battery to the cable connector wires black and red white wire Charging of the backup battery is done automatically while driving We recommend to use gel battery 12V 1 3Ah The battery endurance is 30 to 60 hours depending on momentary operating mode of the GPS locator GPS locator MBE E ARES ODDOGOA View into the connector Red LED indicates GSM status LED blinking quick2. activated GPS alarm z 1 to 30 kilometers covered after GPS alarm This parameter is optional and will be activation It is 5 alarm SMS s in total within one activated GPS alarm automatically set to value N10 in case the parameter was not entered Default setting T5 N10 USER S MANUAL GPS locator First alarm SMS is sent immediately after GPS alarm activation and next alarm SMS s are sent every time after either set distance in kilometers is covered or set time in minutes Number of sent alarm SMS s within one activated GPS alarm is determined by parameter Nz The GPS alarm is automatically deactivated when all SMS s are sent However the set mode of protection is still active If the vehicle keeps moving new GPS alarm is activated 4 PIN code change Command format PIN xxxx yyyy Xxxx new PIN code yyyy new PIN code confirmation L Default setting 4321 4321 PIN 2828 2828 For security reasons we recommend to change the PIN code as soon as possible Example PIN code change from 4321 to 2828 5 Configuration of SMS text sent at GPS alarm activation Command format GTEXT xxxxx xxxxx your text of the message max 74 symbols Default setting Alarm Position and speed of your 4321 GTEXT They are car stealing your car The SMS with GTEXT will be sent to a preset telephone numbers after GPS alarm activation The GPS data will follow after this text in the alarm SMS Ex
3. 5759N 015d 048 9452E Okm h 10 09 10 10 08 01GMT 02 00h Lukoil Hradec Kralove Example Response to a position request Example Displaying the position on internet coordinates in the form of a link USER S MANUAL GPS locator 3 Relay controlling using SMS excluding alarm 3 1 Relay switching for unlimited time Command format SWITCH n n 0 unswitched relay n 1 switched relay 4321 SWITCH 1 The relay in the GPS locator can be switched using command SWITCH with parameter n so that particular devices in the vehicle can be remotely switched ON or OFF for unlimited time e g alarm Example Relay is switched sound 3 2 Relay switching for preset time Command format SWITCH xy x time for which the relay stays switched from O to 240 y time unit of the number entered by parameter x y s seconds y m minutes 4321 SWITCH 5m The relay in the GPS locator can be switched using command SWITCH with parameter xy so that particular devices can be remotely switched ON or OFF for limited time Example Command for switching relay for 5 f minutes After this time elapses the relay 3 3 Relay switching for time preset by automatically returns back to unswitched command RELAY mode Command format SWITCH In case you enter command SWITCH without any parameters the data preset by command RELAY are automatically accepted see p 6 4 Request f
4. NPUT protection mode it is 10 02 04GMT 02 00h necessary to have external car alarm installed which output is connected to input contact of the GPS locator INPUT protection sends SMS to authorized Example Alarm SMS GPS alarm telephone number in case that the condition for INPUT alarm activation on input contact of the GPS locator is met Note We recommend to have the external alarm connection done by a professional service Activation of protection INPUT protection is permanently active considering proper installation and connection of external car alarm with the GPS locator was done Deactivation of protection INPUT protection can be deactivated by disconnecting external alarm from input contact of the GPS locator INPUT alarm activation INPUT alarm is activated when external car alarm gets activated In case the GPS alarm was already activated the INPUT alarm will not be activated protection against cyclic communication with external car alarm Reaction to alarm One alarm SMS informing about car attact is sent after INPUT alarm is activated Such SMS may contain also information about a position of a car see configuration command ITEXT p 8 Alarm Your car was attacked Example Alarm SMS INPUT alarm USER S MANUAL GPS locator 2 Position SMS request Command format POSITION The GPS locator responds to POSITION command with one SMS containing GPS data The time in w
5. USER S MANUAL GPS locator GPS LOC USER S MANUAL GPS locator Contents Introduction GPS locator installation into the vehicle Configuration of the GPS locator Switch relay configuration at alarm activation 2 Entering of authorized phone numbers for alarm SMS and controlling of GPS higher level protection mode 3 Setting of time period for sending a current position information at GPS alarm ax ano gt A wo activation 7 4 PIN code change 8 5 Configuration of SMS text sent at GPS alarm activation 8 6 Configuration of SMS text sent at INPUT alarm activation 8 7 Configuration of SMS text sent as a response to a position request 9 8 Setting of alert call in case of alarm activation 9 9 Way of sending GPS coordinates in SMS s 9 10 Setting of confirmation message for SMS commands 10 11 Configuration identification 10 12 Reset renewal of factory default setting 10 User s functions of GPS locator 11 1 Thief protection 11 1 1 GPS protection 11 1 2 GPS higher level protection GPSS 12 1 3 INPUT protection 13 2 Position SMS request 14 3 Relay controlling using SMS excluding alarm 15 3 1 Relay switching for unlimited time 15 3 2 Relay switching for preset time 15 3 3 Relay switching for time preset by command RELAY 15 4 Request for remaining credit in pay as you go SIM card used in the GPS locator 15 5 Setting the GPS locator in STAND BY mode 16 Finding a vehicle position on internet maps 17 1 Findin
6. ample Setting of your own GTEXT 6 Configuration of SMS text sent at INPUT alarm activation Command format ITEXT xxxxx xxxxx your text of the message max 74 symbols 2 Default setting Alarm Your car was attacked 4321 ITEXT Car ame The SMS with ITEXT will be sent to a preset is activated telephone numbers after INPUT alarm is activated In case the ITEXT ends with symbol the GPS data will follow after the ITEXT in the alarm SMS Example Setting of your own ITEXT USER S MANUAL 7 Configuration of SMS text sent as a response to a position request Command format PTEXT xxxxx XXXXXx your text of the message max 74 symbols Default setting Position and speed of your car The SMS with PTEXT is sent as a response to a vehicle position request See below for the command POSITION to the telephone number used for sending the request This text will be in SMS always followed by GPS data 8 Setting of alert call in case of alarm activation Command format CALL x x 0 call function is OFF x 1 call function is ON Default setting 0 If the function is ON the first set authorized telephone number is automatically called after alarm activation This alert call is only warning the user about activated alarm We recommend not to accept the call the locator does not dispose of any voice functions 9 Way of sending GPS coordinates in SMS s Command format LINK
7. esponse 11 Configuration identification Command format CONFIG The GPS locator sends SMS with current Q O gt gt Q Cc o O gt Dv N Dv D n jo O gt n D as O Q O Z En O Q O 3 D gt a Authorized number INPUT and GPS alarm are sent IG CONFIG PHONE 4206021283261G 420777545674G 4207775456701 RELAY 10s IG PERIOD T3 N10 Authorized number GPS alarm is sent G Authorized number INPUT alarm is sent 1 Relay configuration Setting of period for sending SMS s at GPS alarm Setting of confirmation for processed SMS s 1 is ON GPS Call in case of alarm activation 1 is ON Sending coordinates in the form of a link 1 is ON Current relay mode 0 relay is unswitched Mode of GPS protection 0 is OFF Mode of GPS higher level protection 1 is ON Example Received SMS with a current configuration of GPS locator 12 Reset renewal of factory default setting Command format RESET setting After the command is sent initialization of 4321 RESET Example Reset renewal of GPS locator 10 factory default setting USER S MANUAL GPS locator User s functions of GPS locator User s functions of the GPS locator are controlled by commands sent as an SMS from your mobile phone to the GPS locator telephone number Command is always sent together with PIN code which defines authorized user s The PIN code i
8. g SMS s therefore it is essential to pay attention to rates for SMS services while choosing your mobile operator We recommend you to activate roaming on the SIM card just in case of localization of the vehicle abroad The GPS locator unit connects to a vehicle onboard power 12V DC We recommend you to connect the unit to a backup battery just in case the main power source is stolen or inactivated The GPS locator allows other functions which are described in details in this user s manual GPS locator installation into the vehicle The GPS locator is intended either for separate connection or as an addition to a car alarm 1 Push the releasing button and slide out the SIM card holder Insert the SIM card in the holder and slide back in the GPS locator together with the SIM card Note At first the SIM card needs to have PIN code protection deactivated The PIN code protection can be deactivated for example in a mobile phone 2 Connect particular wires from cable as seen on the aria right The cable connector must be disconnected from the GPS locator during wire connecting USER S MANUAL Pin 1 Brown Switching relay common contact COM Pin 2 Green Switching relay opening contact NO Pin 3 Blue Switching relay closing contact NC Pin4 White External alarm input AO Pin5 Yellow Input ignition Pin6 Orange External alarm input A1 Pin10 2x black Frame 12V backup power source Pin11 Red 12V Pin
9. g a vehicle position on server SATMAPS NET 17 Troubleshooting 18 USER S MANUAL GPS locator Introduction Dear customer thank you for purchasing our product lt is a modern and technologically advanced GPS locator This product will help you to secure and protect your vehicle car truck motorcycle caravan construction machine agricultural machine motorboat etc In case the guarded vehicle is stolen the GPS locator will send you a current position to your mobile phone Via mobile phone you can easily view the current map with vehicle position on the display This service of a displaying on a map is completely free of charge You can also view the position of a guarded vehicle via PC and website http www satmaps net free of charge The system consists of a GPS locator unit and a satellite GPS antenna The GPS locator unit is usually placed in a hidden and a difficult to approach place e g under a car dashboard SIM card of the GSM mobile operator is placed inside the GPS locator unit the GPS locator has its own telephone number It is possible to use a contract or a pay as you go SIM cards In case you decide to use a pay as you go SIM card you can check its remaining credit using your mobile phone Charging of the pay as you go SIM card can be done from your mobile phone or for example using ATM check possible options for a remote pay as you go SIM card charging with your GSM operator The system will communicate with you usin
10. hich the device responds depends on the fact if the GPS module is momentarily switched ON at least one GPS protection is ON or the car engine is ON and it can also depend on the strength of GPS signal reception In case the locator does not manage to detect valid GPS data within 5 minutes after receiving the request the device sends SMS Example Finding of momentary GPS position with last known data marked as OLD in case this position was detected after the device is switched ON 4321 POSITION Note The user can send the command POSITION request independently on the state of protections and on the state of activated alarms Position and speed of your car 50d11 2842N 015d49 7743E Okm h 10 09 10 0 08 02GMT 02 00h Default text setting change is possible by command PTEXT GPS coordinates displaying coordinates in the text form Speed of the vehicle GMT and time correction In case of setting the function LINK to value 1 function is switched ON the GPS locator sends rn ji H xample esponse to a position reques SMS with GPS coordinates in the form of a link to cootdinates in the text farm display the vehicle position on the internet 587 T ebe Kr lovehradeck 500 11 Cesk republika zm nit lokalitu P ibl it Odd lit GPS coordinates displaying PE coordinates in the Position and speed form of a link of your car http satmaps net 50d12
11. ly 1x per second LED blinking slowy 1x per 3 seconds The device is connecting to GSM network The device is connected to GSM network LED is not blinking The device is switched OFF Green LED indicates GPS status LED blinking quickly 1x per second LED blinking slowy 1x per 3 seconds LED is not blinking The device is trying to receive GPS data The device receives actual GPS data GPS module is switched OFF Functions of indication LEDs USER S MANUAL GPS locator Configuration of the GPS locator The GPS locator configuration is performed using instructions sent as an SMS from your mobile phone to the phone number of the GPS locator Command is always sent together with PIN code which defines authorized user s The PIN code is a four digit number which can be changed The PIN code is set by manufacturer to value 4321 symbols are used instead of PIN code in the text below The commands can be typed both in regular or capital letters In case the command is not sent in a correct form the GPS locator will send SMS with the text COMMAND ERROR In case the command is sent with incorrectly entered parameters the GPS locator will send SMS with the text key word ERROR 1 Switch relay configuration at alarm activation Command format RELAY xy z x time for which the relay stays switched 0 to 240 yz y time unit of the number entered by parameter x VS pees 4321 RELAY 30m G y m min
12. o the SMS e g 10 02 04GMT 02 00h if not only GMT time is shown e g 10 02 04GMT 1 2 GPS higher level protection GPSS This mode is identical with GPS protection mode but does not evaluate car ignition status GPS alarm gets activated every time when the vehicle starts moving Activation of protection GPS higher level protection is activated by ringing the GPS locator telephone number from authorized telephone number the GPS locator rings 2x and then rejects the call Deactivation of protection GPS higher level protection is also deactivated by ringing the GPS locator from authorized telephone number alarm deactivation is confirmed by immediate rejection of the call by GPS locator Deactivation must be done prior to any drive GPS alarm activation GPS alarm is activated when the vehicle starts moving USER S MANUAL GPS locator Reaction to alarm Alarm SMS s with the car position data are being sent during the whole alarm duration The total number of alarm SMS s depends on a momentary configuration see configuration command PERIOD The activated GPS alarm can be deactivated by ringing the telephone number of GPS locator from Alarm Position and authorized telephone number alarm deactivation is confirmed by immediate rejection of the call by GPS P ON cal locator By ringing you also deactivate the mode of GPS protection 015d49 7743E 20km h 1 3 INPUT protection 10 09 10 To be able to utilize I
13. on activation Default setting 1 Deactivation of protection The GPS protection can be deactivated using command GPS 0 There is no need to deactivate protection using any command before every single driving since protection is deactivated automatically after car ignition is set ON 4321 GPS 0 GPS alarm activation GPS alarm is activated when the vehicle starts moving while car ignition is OFF e g towing Example GPS protection deactivation USER S MANUAL GPS locator Reaction to alarm Alarm SMS s with a car position data are being sent during the whole alarm duration The total number of alarm SMS s depends on a momentary configuration see configuration command PERIOD The activated GPS alarm can be deactivated by ringing the telephone number of GPS locator from authorized telephone number alarm deactivation is confirmed by immediate rejection of the call by GPS locator Function of GPS protection stays active until deactivated by command GPS 0 Default text setting change is possible by command GTEXT GPS coordinates Speed of the vehicle Date 0 02 04GMT 02 00h GMT and time correction see the note below Note Example Alarm SMS GPS alarm The GPS locator shows GMT in the SMS s The GMT is a part of the GPS info Some GSM operators provide local time correction in relation to GMT If your GSM operator supports such service the GPS locator adds time correction info t
14. or remaining credit in pay as you go SIM card used in the GPS locator Command format CREDIT xxxxx xxxxx dialed number for info about remaining credit in the pay as you go SIM card Contact your GSM operator for the information 4321 CREDIT 104 The system will respond by message from your operator containing info about current credit in the SIM card This function is applicable only if a pay as you go card is used Example Command for getting info about current credit in a pay as you go SIM card 02 used in the GPS locator USER S MANUAL GPS locator 5 Setting the GPS locator in STAND BY mode Command format OFF In STAND BY mode the GPS locator is switched OFF and its power consumption is O mA STAND BY 4321 OFF mode is recommended to be used for long time car parking e g in winter time Example Command for setting in STAND BY mode Mode Description Power consumption Ready The device is ON and Max 20mA responds to all SMS Recommended maximum time for not commands GPS protection using driving the car is 6 weeks and GPS higher level protection are OFF GPS The device is ON and Max 40mA protection responds to all SMS Recommended maximum time for not commands At least one GPS using driving the car is 2 weeks protection is ON STAND BY _ The device is OFF and does OmA not respond to any SMS Recommended at long time parking commands of the vehicle The power consum
15. ption will be temporarily increased by 20mA when the relay is in the switched mode In STAND BY mode the GPS locator does not respond to SMS commands and ringing The GPS locator can be woken up from this mode by either switching car ignition ON or by signal on external input external alarm activation Under such conditions the protection mode set before STAND BY mode activation remains active The only limitation will be during protection against car towing away without either alarm activation or switching ignition ON USER S MANUAL GPS locator Finding a vehicle position on internet maps 1 Finding a vehicle position on server SATMAPS NET a Enter internet address www satmaps net to your internet browser b Type the GPS coordinates received by SMS in Latitude and Longitude fields Position and speed c Click the button Show position on map and wait for showing era iis Of yourcar _ a on a map 50d11 2842N 015d49 7743E _ Ok T 10 09 40 10 08 p2GMT 02 00h SATMAPS er Please enter GPS coordinates in the suli format as in received SMS ae Latitude Longitude ee ew Show position on map Example 50d11 2785N rt 015049 7612E Position and speed of your car 50d11 2785N 015d49 7612E Okm h 08 04 10 14 12 47GMT 01 00h USER S MANUAL PROBLEM The device does not switch ON The device does not log in GSM network red LED is blinking in interval 1x pe
16. r Check whether appropriate GPS protection was activated GPS 1 GPSS 1 e Check whether the GPS antenna is properly connected and placed Check whether entered telephone numbers for sending alarm SMS s are correct Check whether the GPS antenna is placed horizontally and is not obstructed from the top by metal parts of the vehicle The device dispose of a sophisticated algorithm for activation of GPS alarms In very rare cases an activation of false alarm may occur which does not have to be caused by defect of the device or wrong installation This situation might happen in garages and close to high buildings where the device can receive for longer time bad or reflected GPS signal Please contact your dealer the device can be set to its default factory setting including the PIN only by a manufacturer
17. r second The device does not respond to SMS commands The device responds to SMS commands but does not respond to ringing from authorized telephone number The device does not activate GPS alarm False GPS alarm Forgotten PIN code of the device GPS locator Troubleshooting SOLUTION Check the connection of power supply wires and wire input ignition and switch car ignition ON Check whether the SIM card is properly inserted Check availability of GSM operator signal Check whether inserted SIM card has disabled PIN code protection After successful logging the red LED must blink in interval 1x per 3 seconds e Check whether the device is switched ON and logged in GSM network The logging in the GSM can be also verified by ringing the device e Make sure that commands are entered in correct format with valid PIN code In case you use a pay as you go SIM card make sure that the SIM is still active and that there is enough credit for sending SMS s e After the device is switched ON it is necessary to wait for device initialization completion it can last up to 2 minutes before first command can be sent Previous SMS command must be processed before next SMS command can be sent e Check the validity of entered authorized telephone number including a country code by using command CONFIG Verify whether the authorized telephone number has CLIP service activated identification of a calling numbe
18. s a four digit number which can be changed The PIN code is set by manufacturer to value 4321 symbols are used instead of PIN code in the text below The commands can be typed both in regular or capital letters In case the command is not sent in a correct form the GPS locator will send SMS with the text COMMAND ERROR In case the command is sent with incorrectly entered parameters the GPS locator will send SMS with the text key word ERROR 1 Thief protection The GPS locator can be used for protection either separately or together with external alarm Modes GPS protection and GPS higher level protection can be used if the GPS locator is used without car alarm Mode INPUT protection can be used in addition to the two above mentioned modes if external car alarm is connected to the GPS locator 1 1 GPS protection The GPS protection activates alarm if the vehicle starts moving while the car ignition is OFF This is protection against towing the car away We recommend to keep this kind of protection permanently ON This protection does not need to be deactivated before driving The GPS protection sets 4321 GPS 1 itself automatically OFF for the time of driving after car ignition is set ON Activation of protection The GPS protection is activated using command GPS 1 If the protection is activated the car will be automatically protected every time after ignition is set OFF Example GPS protecti
19. ter z is optional If this phone number is entered without this parameter it means that SMS s will be sent to this phone number from both INPUT alarm and GPS alarm the value IG is set automatically Up to 3 telephone numbers can be assigned All entered authorized numbers can control GPS higher level protection mode by ringing the GPS locator number see below The telephone numbers must be entered in international format so the number must always begin with the symbol Note Authorized telephone numbers must have identification of calling number CLIP activated In case this function is not active function of GPS higher level protection cannot be controlled and it is not possible to control the GPS locator by ringing The first authorized number set by command PHONE is called in case of INPUT alarm or GPS alarm activation Condition for calling the first authorized number is activation of this function by a command CALL 3 Setting of time period for sending a current position information at GPS alarm activation Command format PERIOD xy Nz x determines whether next alarm SMS will be sent after a certain time or distance covered 4321 PERIOD D4 N5 x D Distance after distance covered Km x T Time after a certain time minutes y determines the number of kilometers or minutes y 1 to 60 z determines the number of alarm SMS within one Example The SMS will be sent after each 4
20. utes z determines under what circumstances the relay Sa will be switched relay will be switched when INPUT alarm is activated z G relay will be switched when GPS alarm is Example The relay will be switched for 30 minutes at GPS alarm activation activated z G relay will be switched when both INPUT and GPS alarm are activated Parameter z is optional If the command RELAY is entered without parameter z the relay will be switched in both INPUT alarm and GPS alarm activation the value IG is set automatically Default setting 1s IG This command sets the time for which the relay will be switched at alarm activation or while sending the command SWITCH without parameter 2 Entering of authorized phone numbers for alarm SMS and controlling of GPS higher level protection mode Command format PHONE aaaz bbbz cccz VA aaa first authorized number in international format 4321 PHONE 420777 bbb second authorized number in international 200333 42060266688 format 8G ccc third authorized number in international format Example Two authorized phone numbers are entered Only SMS s at GPS alarm activation will be sent to the number 420602666888 USER S MANUAL GPS locator z determines whether alarm SMS to this phone number will be sent during INPUT alarm or GPS alarm INPUT alarm SMS will be sent to this number only z G GPS alarm SMS will be sent to this number only Parame
21. x x 0 sending GPS coordinates in the text form x 1 sending GPS coordinates in the form of a link which shows the vehicle position on the internet Default setting 0 If this function is ON the GPS locator sends a message with GPS coordinates in form with a link Now the user can just click on the link contained in SMS and view the position of the vehicle on internet maps Note If you want to use this function your mobile phone must be connected to the internet and must support the web browser function The service of displaying a vehicle position on the map is completely free of charge GPS locator 4 4321 PTEXT Your car is right here Example Setting of your own PTEXT 4321 CALL 1 Example The function of alert call is ON 4321 LINK 1 Example Command for sending GPS coordinates in the form of a link which shows the vehicle position on the internet is ON USER S MANUAL GPS locator 10 Setting of confirmation message for SMS commands Command format CONFIRM x x 0 confirmation messages OFF x 1 confirmation messages ON Default setting 1 4321 CONFIRM 1 If the confirmation message function is ON after successful command processing the GPS locator sends SMS with the text command OK to the E telephone number sending original command The ample Function of confirmation SMS is confirmation SMS is not sent at the commands where there is a different SMS r
Download Pdf Manuals
Related Search