Operating Instructions UMB-Config-Tool
Contents
1. Status Hs Cancel CAC of loaded file DSE4 Clear target started Clear target succeed Programming target started After successful programming the Config Tool reports as follows Eg i Firmware update succeeded The device then operates with the new firmware Possible sources of error lf a firmware is selected which does not correspond to the sensor the error message Invalid Firmware Filename for this module is displayed When updating older ANACON UMB or older IRS21CON UMB the RS232 connection must be plugged directly into the module to be updated An lISOCON UMB cannot be updated using this procedure see page 22 Manual Update with HexLoad There is a plausibility check with the version number of the installed firmware and the version number of the firmware file A replacement of a newer firmware on a sensor with an older version is only allowed by a direct order from the manufacturer of the G Lufft Mess und Regeltechnik GmbH Fellbach Germany 16 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 module If you don t have the order and the module is damaged by the action the warranty is void tufft a G Lufft Mess und Regeltechnik GmbH Fellbach Germany 17 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Calibration of a VS20 UMB visibility sensor Start by creating a sensor list containing the VS20 UMB to adjust Example E2. timeout has to be specified to wait for the responses of the devices in the UMB setup The times given in the configuration dialog are ms For direct LAN connections to IP addresses values of 100 ms are sufficient For example targets with name resolution and GPRS connections require values up to 10000 ms Note Only the communication connection type raw is currently supported not Telnet emulation Note The set times are also considered for RS232 connections Configure TCP IP settings ol x Hostadress or hostname TCP Port 192 168 0 13 je000 Additional Timeout for slow connections to host TCP IP OF Cancel Creating a sensor list Menu Edit gt Sensors He ufft 4 oS G Lufft Mess und Regeltechnik GmbH Fellbach Germany Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 5 x Sensor Selection Type of Sensor ID WS 20 UMB 1 SayveE sit Delete Modify Configure Cancel E xit Update Channellist Firmwareupdate Sensor Selected Sensors Ho Type Address Channels Active Channels 1 VS20 UMB 03001 12289 40 0 Click Sensor to editremove Sensor Double Click Sensor to edit active channels Autoscan Verity Save to Disk Load from Disk Choose T ype of Sensor enter an ID and add it with Add to the list With Delete sensors can be deleted with Modify a sensor in the list can be modified The sensor show
3. are different from those in the device description of the sensor always the details in the operating manual for this sensor version counts see also channel list update a sensor The UMB Config Tool is single seat software It is not intended that multiple users use this software from the same directory at the same time The UMB Config Tool is able to create logfiles When these files are opened by other programs during the operation of the UMB Config Tool there might occur writing errors i o Errors when the UMB Config Tool tries to update them and the file will not update correctly Details to special functions for sensors can be found in the operating instructions of the sensor Installation UMB Config Tool Start Setup UMB_ Config_xxxxxxx EXE and follow the instructions of the installation programme The software is installed under C Lufft UMB Config as standard In MS Windows Vista and MS Windows 7 you must not install the software in the directories C Program Files or C Program Files x86 because these directories are specially protected system directories and the protection does not work well with the normal program function of this tool Start the application with Start gt Programme gt Lufft UMB Config gt Config Tool Installation paths Path Content Lufft UMB Config Application and INI files Lufft UMB Config Firmware Device firmware mot files Lufft UMB Config H
4. network requires a unique address Addressing takes place via a 16 bit address This is divided into a sensor class ID anda device ID To avoid address duplication the device ID s are assigned in ascending order per sensor class i e sensor type 2 station Sensors Sensor Selection Type of Sensor ANACON UMB ja Update Channellist Firmwareupdate Sensor ID Selected Sensors Delete Modify Configure o x Save E wit CancelE sit DO ime oes Channels Active Channel E w MM ost hm OS mo oS i a aA Click Sensor to editvremove Sensor IRS21CON UMB 0x1001 4057 IRS21CON UME Ox1002 4098 IRS21CON UME Ox1003 4099 R25 UMB Fi2o UMB YO20 UMB Y520 UMB ANACOM UMB ANACOM UMB ANACOM UMB ANACOM UMB Ox2001 81 93 Ox2002 91 34 Ox 3007 1 2269 Oxs002 1 2290 OvBOO1 245 77 OvbO02 245 79 Ox6003 245 79 Ox6004 24590 26 26 26 15 15 40 40 135 135 135 135 co m i E a a G ol o o o ro o o o Double Click Sensor to edit active channels Autoscan Verity Save to Disk Load from Disk ATTENTION When configuring new equipment please note that new devices always have the ID 1 If there are several sensors of the same type in a network it makes sense to configure the sensors individually with their corresponding ID s before commissioning the network Interface Settings The interface settings made by the UMB Config Tool relate to the specified sens
5. 3 4F 4F 2A 20 20 20 20 TS0OC N 7 Start the programming with F9 8 If programming is successful the message Job succeed is displayed then exit HexLoad 9 The module is now ready for operation with the new firmware Manual Update of IRS21CON UMB If it is necessary to update an ISR21CON UMB module manually proceed as in the case of Update ISOCON UMB where the name of the mot file must correspond to IRS21con_Vx_x mot 4 ufft 22 oS G Lufft Mess und Regeltechnik GmbH Fellbach Germany Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Manual Update of VS20 UMB R2S UMB and other UMB Sensors a a 8 9 Disconnect the power supply of the sensor from the ISOCON UMB Switch on the power supply of the ISOCON UMB module Connect the RS232 interface of the ISOCON UMB module to the PC Start HexLoad Programme Lufft UMB Config Hexload HexLoad exe Load the current mot file with File gt Open The file must have the following designation where xx specifies the version number e VS20 UMB vs20_release_Vxx mot e R2S UMB R2S_Release_Vxx mot e WSx UMB WSx_Release_Vxx mot e IRS31 UMB IRS31_Vxxx mot e ARS31 UMB ARS31_Vxx mot e VENTUS UMB Ventus_Vxx mot e V200A UMB Ventus_Vxx mot e NIRS UMB NIRS_Release_Vxx mot Connect the power supply of the sensor to the ISOCON UMB modul
6. D Since every Failed is repeated 2 times default setting that is altogether 131 queries If now AdditionalTimeoutInMSForSlowConnections IT oHost is set to 10s Autoscan takes about 25 minutes so choose the parameters carefully if the Autoscan function is to be used Lufft 21 GC G Lufft Mess und Regeltechnik GmbH Fellbach Germany Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Manual Update with HexLoad The following procedure must be applied if a sensor update using the Config Tool was interrupted or in the case of an ISGOCON UMB Update ISOCON UMB Disconnect the power supply and the connected sensor from the ISOCON UMB module Connect the RS232 interface of the ISOCON UMB module to the PC Start HexLoad Programme Lufft UMB Config Hexload HexLoad exe Load the current mot file with File gt Open This must have the file designation isocon_release_Vxx mot where xx specifies the version number Switch on the power supply of the ISOCON UMB module BTL_ISOCON_Vx must now be displayed in HexLoad in the Target window next to Application ee Do F HexLoad 3 00j _ O x File Edit wiew Target Options Window Help x Range E8000 FDFEF CRC Baudrate 19200 Application BTL IS0CON J1 Jun 6 2006 15 5 wt TO i Apin CPU BTL ersion BTL Y3 00 Address rm Tr F Fy ER AAA 0 3D 1 3D e 49 G3 4F 4
7. ID fi Linespeed 19200 Y Description visibilty sensor WS 20 UMB Protocal binary Timeout protocol change f min Output properties Measurement Setup Output mode 4 20m Average for visibility miri Failure current mA E Offset for visibility m Scaling 0 2000 m Border contrast Average for temperature min Offset for temperature C Calibration values DAC offset 63 95246 Calibration value 6201 97 754 Calibration status E DAC gain 163 11475 Calibration offset 0 00033 G Lufft Mess und Regeltechnik GmbH Fellbach Germany 6 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 After the values have been set store them on the device with Store profile on sensor iol x Select sensor to configure Load profile from sensor Jox3001 12289 Load profile from disk Store profile on sensor Store profile on disk Load ad date trom disk Clase With Store profile on disk a sensor configuration might be stored on a hard drive Stored configurations of sensors might be loaded with Load profile from disk Note In case of a service call a saved sensor configuration helps a lot more than one or more screenshots of the sensor configuration a ufft i y oS G Lufft Mess und Regeltechnik GmbH Fellbach Germany Operating Instructions UMB Config Tool Assigning Device ID s Status 08 03 2013 version 1 9 Each device in a UMB
8. Ss Max temperature CH 200 00 450 00 inactive AE ufft G Lufft Mess und Regeltechnik GmbH Fellbach Germany 10 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Here you are able to select the channels for query either through clicking the corresponding channel in the list or by using the Multiple channel action function with the channel numbers Example If channels 100 120 140 and 160 of the list above should be selected for query with the UMB Config Tool this could be done with the following settings Add channel from 100 Add channel to 160 Delta for channel 20 Multiple channel action Select channels and then click on Go Note If a channel mentioned in the operating instructions of a sensor is not shown in the sensor list the channel list of the UMB Config Tool for this sensor needs to be updated It is advised that you update the Firmware of the sensor before updating the channel list see chapter Firmware Updates The measurement is started in menu File gt Start measurement E Config Software UMB COM1 19200 B x File Edit Gptions Help To change the sampling rate of the software click Edit gt Sampling Rate A sample rate of 1s does not correspond to the UMB protocol In the case of missing answers of the sensor it can lead to erroneous presentation of the received values Attention The selected channels only affect the dat
9. UMB Config Tool Operating Instructions UMB Configuration Software Status 08 03 2013 Document version 1 9 G LUFFT MESS UND REGELTECHNIK GMBH POSTFACH 4252 70719 FELLBACH TEL 49 711 51822 0 FAX 49 711 51822 41 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Table of Contents Preface designated use 3 Installation UMB Config Tool 3 System requirements 3 Communication settings communication 4 Creating a sensor list 4 Configuring sensors 6 Assigning Device ID s 8 Interface Settings 8 Configuring ANACON UMB 9 Configuration of sensors operating in different protocols e g MODBUS SDI12 10 Query measurement values 10 Updating the channel list for a sensor 11 Firmware Update 13 Check current firmware status 13 Programme a Sensor Update 14 Possible sources of error 16 Calibration of a VS20 UMB visibility sensor 18 Resetting the rain quantities of WSx UMB 19 Resetting the service level of NIRS31 UMB 19 Miscellaneous 19 Manual Update with HexLoad 22 Update ISOCON UMB 22 Manual Update of IRS21CON UMB 22 Manual Update of VS20 UMB R2S UMB and other UMB Sensors 23 Version history Document Edited by Description of amendment version to 24012007 EES Taken from Shor Instructions VO2 and completed fa rece2007 Ees Syste requremenss sppremeried 3 10 02 2009 BR Adjustments for Software VLO Engis SSS r4 27102009 BR Adjustments for Software V1 1 English SSS 75 08 10 2010 BR Ad
10. a query in the UMB Config Tool They do not influence the query of channels in any other software Updating the channel list for a sensor Add the desired sensor to the measurement setup and make it to the selected sensor by clicking the list entry ea ufft G Lufft Mess und Regeltechnik GmbH Fellbach Germany 11 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 0 x Sensor Selection Type of Sensor ID DACONS UMB fi Save Exit Add Delete Modify Configure Cancel E xit Update Channellist Firmwareupdate Sensor Selected Sensors 1D Type Address Channels Active Channels 1 0 j DACONS UMB OxF001 61441 O A annasnnssnnnsnnssnnnnnnnnnnnnnnnnnnasnnnsnas Click Sensor to edit remove Sensor Double Click Sensor to edit active channels Autoscan Verify Save to Disk Load from Disk Then choose Update Channellist The UMB Config Tool now reads the channels from the desired sensor and sorts the new ones into the channellist During this operation no channels are deleted but descriptions and other information of the old channels are replaced by the newly read ones Also the Type of Sensor might be changed during this operation This process also works for up to now unused sensortypes However such sensors cannot jet be configured with the UMB Config Tool but querying measurement values works tufft 12 oS G Lufft Mess und Regeltechnik GmbH Fe
11. e The following test must now be displayed in HexLoad in the Target window next to Application e VS20 UMB BTL _VS20_V Th Project o x 0 x Hextile _vs20_release_VIY E8000 FOFEF COM Port CPU SE n OADIN BTL Yersion BTL 3 00 Baudrate 19200 application BTL v520 v3 D 6 2006 16 04 e R2S UMB BTL _R2S V Hexfile C R28 _Release_V3B Range E8000 FDFEF COM Port ee CRC Baudrate 19200 Application CPU BIL ersion BIL 3 00 Start the programming with F9 If programming is successful the message Job succeed is displayed then exit HexLoad 10 The module is now ready for operation with the new firmware Lufft 3 23 oS G Lufft Mess und Regeltechnik GmbH Fellbach Germany
12. esetting the rain quantities of WSx UMB With the menu point Extras gt reset WSx UMB rain sums the absolute values of the rain quantities in all connected WSx UMB are set back to 0 It is not necessary to establish a measurement setup with the WSx UMB It is however recommended to check if the command has been carried out successfully by reading out the respective values on the corresponding WSx UMB Resetting the service level of NIRS31 UMB After carrying out maintenance and replacing the reflector unit the sensor must be informed about this procedure using the UMB Config Tool In the menu under Options select the entry NIRS31 UMB NIRS31 UMB Service UME Config Tool File Edit Help Switch all sensors temporarily to UME Protocol R5232 special functions VS520 UMEB Callibration WSx UME reset rain NIRSS1 UMB NIRS31 UMEB Service Close Communication Port NIRS31 UMB check adaption ARS31 Pro UMB Reset Factory Default NIRS3S1 UMB generate statustile Confirm the performance of maintenance with OK MIRS31 UMIE Service The following works were camed out according to the manual W reflector unit has been replaced Cancel Important note Only use this function if maintenance was actually carried out and the reflector unit was actually replaced Miscellaneous Edit a Password entry allows the user to change in a different user group with advanced possibilities Parameter
13. exload Bootloader programme Lufft UMB Config Konfig Stored device configurations Copy the current device firmware into the firmware directory prior to installing firmware updates The UMB Config Tool can be uninstalled with Lufft UMB Config UNWISE EXE System requirements Windows 2000 XP Vista 7 32 or 64 Bit 10 MB free hard disk capacity A free serial interface COM for configuration diagnosis and firmware update Alternative TCP IP connection to the measurement setup for configuration and diagnosis Lufft Ge G Lufft Mess und Regeltechnik GmbH Fellbach Germany 3 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Communication settings communication The UMB Configtool works in principle with connections to the measurement setup with connection settings 19200 baud 8 data bits 1 stop bit no parity A different baud rate is only possible by editing the file ULSPS INI From UMB Configtool version 1 5 in addition to the direct serial connection to the measurement setup a connection using TCP IP is supported The TCP IP communication is enabled in the UMB Configtool by setting Edit gt Use TCP IP The measurement setup is connected to an RS 232 RS 485 to LAN WLAN adapter or similar device The UMB Configtool supports the connection to a host name or IPv4 address Because TCP IP connections as opposed to direct RS232 connections are affected by latency an additional
14. justments for Software V1 9 English SSS te 18 02 2011 BR integration of new sensors bugfix heater capacity Ventus UMB 1 7 08 08 2011 Integration of ARS31 PRO Smoothing operator for ft ARS31 adjustable Protocol switching functionality for sensors running in different protocols Coupling of IRS31 and ARS31 integrated Anacon New sensor CMPx integrated TCP IP support Centralized settings for WSx energy management 02 02 2012 Manual for UMB Config Tool V1 6 Updates for ARS31 Pro for actual state of development Updates for DPl awareness Units are shown for all adjustments when available Analogue outputs When the source channel is changed the range for the output is automatically adjusted Support for write protected sensor configuration files implemented Option to chose name path for sensor configuration files 1 9 08 03 2012 Extended NIRS31 UMB service functions Warning when trying to downgrade a firmware of a module BY G Lufft Mess und Regeltechnik GmbH Fellbach Germany 2 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Preface designated use The UMB Config Tool has been created for configuring commissioning maintaining calibrating and checking Lufft UMB sensors modules and systems lt is not designed for reading out and storing data permanently For the permanent data evaluation Lufft offers the software SmartViews When in the UMB Config Tool values or ranges of values are shown and these
15. llbach Germany Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Firmware Update Before implementing any update please check with Lufft concerning the current firmware status of the UMB products You must not program an older firmware into a module than the one which is currently installed without consulting Lufft over this issue Check current firmware status The current status of the firmware should be checked before updating the firmware To do so read the configuration under SensorConfig The current version of the software is shown under Rev firmware on the Info page Rsm Serlalnumber 001 0706 0007 000 8 Humber B0 Tested 70E Project number BOOZ Rev bom Rev schematic Rev hardware Rev firmware Rew contig Rev device Class id 40 corresponds to Version V4 0 Lufft L G Lufft Mess und Regeltechnik GmbH Fellbach Germany 13 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Programme a Sensor Update Before updating save the current device firmware mot file in the installation directory under Firmware e g C Programme Lufft UMB Config Firmware ATTENTION When updating ANACON UMB or IRS21CON UMB the RS232 connection must be plugged directly into the module to be updated Anacon UMB and IRS21CON UMB with production date from February 2009 on can also be updated over the bus ANACON UMB without frontside RS232 can on
16. ly be updated over the bus This requires at least one ISOCON UMB in the measurement setup ISOCON UMB have to be updated manually The corresponding instructions can be found the section Updating manually with HexLoad Open the sensor list under Edit gt Sensors if necessary regenerate the list with Autoscan or load a stored list with Load from Disk With Verify check whether the sensors available in the sensor list are also reachable on the network 2 Station Sensors _ O x Sensor Selection Type of Sensor ID WS20 UMB fi SaveE sit Add Delete Modify Configure Cancel E xit Update Channellist Firmwareupdate Sensor Selected Sensors ID pe os eres Botve Channel Ve20UMB Ox001 12289 40 0 1 IRS21CON UMB 0 1001 4097 26 0 1 ANACON UMB Ox6001 2457 135 0 Z ANACON UMB Ox6002 24578 135 0 1 A25 UMB 0s2001 8193 15 0 Click Sensor to editvremove Sensor Double Click Sensor to edit active channels Autoscan Verity Save to Disk Load from Disk Select the appropriate sensor from the sensor list the selected sensor is displayed in the Selected Sensors section VS20 UMB in the example The update process is started with Firmwareupdate Sensor The following window opens when this function of the Config Tool is used for the first time ea ufft G Lufft Mess und Regeltechnik GmbH Fellbach Germany 14 Operating Instructions UMB Config To
17. me in minutes set under timeout for protocol change in the sensor settings by UMB Configtool UMB telegrams e g Measurement acquisition configuration read write reset the timeout to the time set After a reset the sensor is running again in the configured protoco Note After a Store profile on Sensor the sensor is reset automatically by the UMB Configtool and then runs again in the configured protocol This functionality is available on the following products Sensor __ Firmware version or higher _ Version 1 2 o Version 1 2 Query measurement values The channel list of a sensor is opened by double clicking a sensor in the sensor list amp Select active Channels Chr Measurement Range active Click on Channel to toggle active 200 00 450 00 Add channel from 200 00 450 00 inactive 1 Add channel to 100 Act temperature CH1 Min temperature CH1 Max temperature CH1 200 00 450 00 inactive Avg temperature CH 200 00 450 00 inactive eE 328 00 842 00 active 1 iS 328 00 842 00 inactive Multiple channel action Select channels Act temperature CH1 Min temperature CH1 Max temperature CH1 320 00 842 00 Inactive Deselect channels Avg temperature CH1 328 00 842 00 inactive Deselect all channels Act temperature CH2 200 00 450 00 inactive Min temperature CH2 200 00 450 00 inactive o Gey Ged a Cy Cy CP THY THY THY THY Gf Cay Gay Of
18. n in Sensor Selection will be deleted or modified Configure starts the configuration of the sensors in the list Firmwareupdate Sensor starts the module for updating the firmware of the selected sensor Update Channellist reads the channel list from the connected UMB module sensor and inserts new channels into the existing channel list for this device Running Autoscan queries the network for existing UMB devices Verify checks if the devices in the list are responding to communication from the master With Save to Disk the sensor list including selected channels can be stored for later reuse Load to Disk A KA Lufft ioe G Lufft Mess und Regeltechnik GmbH Fellbach Germany 5 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Configuring sensors Select a sensor from the list by clicking it then click Configure You will get the following dialogue 10 x Select sensor to configure Load profile from sensor 0s3001 12289 Load profile from disk Store pratile on sensor Store profile on disk Load adj data tram disk Close The check box select sensor to configure allows to switch to another sensor of the measurement setup Load the configuration of the sensor with Load profile from sensor Adjust the values in the mask to suit your needs 10 x Main Info 520 UMB General properties Communication properties
19. oScanDeltaForFail 3 With Autoscan for each possible group by address 1 beginning a Verify command is sent If the device does not respond the next AutoScanDeltaForFail 1 addresses in ascending order are queried with Verify The queried groups are 1 to 14 group O is used for equipment spreading broadcasts group 15 are masters here the software itself Example Messurement setup with 1 device of group 2 Id 1 and 1 device of group 3 Id 2 AutoScanDeltaForFail is set to 3 List of queries addresses in Groupid ld notation 1 1 Failed 1 2 Failed 1 3 Failed 2 1 OK 2 2 Failed 2 3 Failed 2 4 Failed 3 1 Failed 3 2 OK 3 3 Failed 3 4 Failed 3 5 Failed 4 1 Failed 4 2 Failed 4 3 Failed 5 1 Failed 5 2 Failed 5 3 Failed 6 1 Failed 6 2 Failed 6 3 Failed 7 1 Failed 7 2 Failed 7 3 Failed 8 1 Failed 8 2 Failed 8 3 Failed 9 1 Failed 9 2 Failed Lufft 3 20 GC G Lufft Mess und Regeltechnik GmbH Fellbach Germany Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 9 3 Failed 10 1 Failed 10 2 Failed 10 3 Failed 11 1 Failed 11 2 Failed 11 3 Failed 12 1 Failed 12 2 Failed 12 3 Failed 13 1 Failed 13 2 Failed 13 3 Failed 14 1 Failed 14 2 Failed 14 3 Failed Thus 45 telegrams in order to find the 2 devices with this I
20. ol Select path to Hexload Program verwendete D Deskto p Eigene Dateien E Wa Arbeitsplatz Eea Dateiname r ung l Dateityp Hesload program ae Abbrechen we Under Hexload select the HexLoad exe file Status 08 03 2013 version 1 9 After this and on all future updates a window opens in which you select the relevant mot file for the update Firmware to update current active sensor Suchen in O Fimwae 0 e Fe W 0007 _RRS_Release_ 42 mot sai anacon_release_w11 mot Zuletzt isocon_release_V12 mot vermendete D Dezkto E Eigene Dateien Wr Arbeitsplatz Eeee Dateiname vs20_telease V1 6 mat ung l Dateityp Firmware file ad A Lufft he Lu G Lufft Mess und Regeltechnik GmbH Fellbach Germany 15 Operating Instructions UMB Config Tool The device is then programmed P HexLoad 3 04 File Edit View Target Options Window Help mimea Target Range CRC Application CPU BTL Version 7 Project Hextile COM Port Baudrate 520 RELEASE V16 MOT COMI 19200 Status 08 03 2013 version 1 9 O x 5 x E8000 FDFEF BIL _Y520_ 3 Jun 6 2006 16 04 M16C 26 64pin BTL 3 00 ah Current data D PROGRAMME LUFFT UMB CONFIG FIRMWARE 520 RELEASE Yie MOT i i Address OxE 8000 E 2 xd 3 18 45 68H F HH t6 C 4 ci FH YH C 28 Fi Programming ta 46 F4 42 GF F7 3 a BE Merat
21. or Attention Only change the interface settings if you are sure you have to and if you are aware of all the consequences of this change This change may not be reversed in a simple manner xe Ai o tufft G Lufft Mess und Regeltechnik GmbH Fellbach Germany 8 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Configuring ANACON UMB As the ANACON UMB is a universal measurement transmitter which can be operated with various analogue sensors this module must always be configured to the connected sensor before commissioning To do this connect the module to the power supply with no additional participants on the bus and connect to the PC via an RS232 cable 1 1 Load the current configuration via Load profile from Sensor as in the section Configure Sensor Select the connected sensor type in Measurement Setup under Channel 1 and Channel 2 51 x Main Info Anacon UM B General properties Communication properties ID i Linespeed RS232 fis Description measure moduleANACON U Protocol binary S Timeout protocol change 10 Meassurement Setup General Parameters Channel 1 Channel 2 Measurement category Unit temperature E Mas value Offset in Unit from Channel o o Jo 000 combi wind 8368 01 Overrange 2 Sensor powerup time ma combi wind 4 20mA extern 0 E J combi wind 4 20mA intern F Humber of samples for ave
22. rage 12 Average over G0 s Channel description charnel 1 lf necessary set the ID measurement interval and number of measurements for the min max and average values Meassurement intervall 3 Number of samples for average fi 2 Average over 60 s Then save the amended configuration in the module with Store profile on sensor under Main ATTENTION In the case of the temperature humidity sensor TFF 8160 TFF the values for C12 and C76 which are marked on the sensor head must be recorded under General Parameters General Parameters Channel 1 Channel 2 Altitude m 100 TFF C12 fi E25 TFF CFE fi 956 ae ufft G Lufft Mess und Regeltechnik GmbH Fellbach Germany 9 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 Configuration of sensors operating in different protocols e g MODBUS SDI12 lf sensors are permanently set to protocols other than UMB Binary or ASCII they must be changed first to the UMB protocol if you want to change the configuration with the UMB Configtool The procedure for doing this is as follows 1 Separate measurement setup from the supply voltage 2 In the UMB Configtool select Options gt Switch all sensors temporarily to UMB protocol 3 Connect the Measurement setup again to the supply voltage 4 After about 5 seconds or longer click Exit in the UMB Configtool The sensors can now be configured for the ti
23. s only adjustable by modifying the file ULSPS INI Settings Log Tl oFile 1 Writes the measurement values into a log file file name see LogFileName The column headers are formatted GroupID ID Channel see table of measurement values LogFileName Values I xt Basic file name for the log file Will be expanded by the current date The software creates a new file for every new date ie ufft G Lufft Mess und Regeltechnik GmbH Fellbach Germany 19 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 CreateDayFiles 1 The registered values are stored in daily files If the value is O they are all stored in one single file MaxRetriesForProtocolWhenFailure 2 Number of retries per command before a failure is reported AdditionalTimeoutInMSForSlowConnections ToHost 0 Time in ms which is waited additionally to the period of reply specified in the UMB protocol before for this instruction Timeout is produced The time specified in the protocol applies to direct 1 1 communication If the query is made e g by GPRS consider using 10000 ms corresponds with 10s here Note With 2 repetitions for each instruction see MaxRetriesForProtocolWhenFailure it takes 3x10s 30s before this instruction is rated as Failed Absolutely consider if an Autoscan is to be accomplished and or a measured value query is run with a short interval This setting will be adjustable in the TCP IP configuration dialogue Aut
24. station Sensors Sensor Selection Type of Sensor ID F25 UME il Save E xit Add Delete Modify Configure CancelE xit Update Channellist Firmwareupdate Sensor Selected Sensors type Address Channels Active Channels 1 R25 UMB 02007 8193 15 0 1 ANACON UMB Ox6001 24577 135 0 1 WS 20 UMB Ox5001 12289 40 0 Click Sensor to editvremove Sensor Double Click Sensor to edit active channels Autoscan Verity Save to Disk Load from Disk Then chose Save Exit Calibration gt VS20 UMB Run the calibration according to the description in the text field and like described in the manual from the calibration kit See picture below E Config Software UMB COM1 19200 Eile Edit Options Help Calibration Step G 0x3001 12289 i Calibration process S20 UMB Start e Step 1 C3 ally Required items Stop 1x Calibration kit visibility 8366 UKAL1 C4 The calibration procedure will take about 10 minutes When the calibration process is interrupted the S20 will not measure until reset or power off cs CE Press Start when you have all the equipment ready and you want to proceed s Press Stop to cancel 8 g Scattering coefficient Enter scattering coefficient here Lufft L G Lufft Mess und Regeltechnik GmbH Fellbach Germany 18 Operating Instructions UMB Config Tool Status 08 03 2013 version 1 9 R
Download Pdf Manuals
Related Search