USER'S MANUAL
Contents
1. We recommend shutting the Soft water inlet stopcock in case of prolonged absence due to vacation travel etc E BOLT B RUBBER SEAL C FLAT WASHER D LOCKING WASHER HOSE CONNECTION ON STOPCOCK HOSE FITTING INSTRUCTIONS The hose A goes past the surface of the rubber seal B in order to preventirregular cuts compromising the seal DETAIL A After fitting the hose A position the rubber seal B the flat washer C the locking washer D and the bolt E Now tighten the screw E manually as it will be responsible for closing the locking washer D fostering the necessary fixing of the hose so there are no leaks DETAIL A The appliance can be installed on a counter top or wall mounted according to your convenience fig 2 For proper operation a cool dry and well ventilated location sheltered away from sunlight indoor use should be chosen We recommend that you do not install it fitted into a cabinet or wall without proper precautions regarding ventilation In any of the installation options make sure of the perfect leveling of the appliance Brackets for wall mounting and 8mm bushings S8 used in wall installation are dimensioned to support your purifier during conditions of use without vertical overload For your safety make sure the location chosen is suitable to support the weight of the appliance in conditions of use 17 kg and that there is no hydraulic an2. transport company for appropriate action 02 IMPORTANT NOTE MSoft cont Your Soft Water Purifier has a system with high filtration technology and it is in accordance with NBR Brazilian Standard 16 098 2012 This system was not designed to be used where the water is bacteriologically unsafe or of unknown quality The water must be drinkable i e treated by water supply utility company as per Ordinance No 2914 of the Ministry of Health For the best operation of your Purifier and a guarantee of the water supplied it is important to alert you to the use of Everest original filters The original filter comes packed in a sealed and personalized plastic bag along with an instruction card for filter change which has the Ejoresf G 3 Soft embossed logos onthe casing NA 03 TECHNICAL DATA SESOft rt MEOH 28x 30 5 x 370m 36x 27 5 x 37cm 39 5 x 30 5 x 37cm 39 5 x 30 5 x 37cm B Soft t nt GROSS WEIGHT EN ma i Tkg TREFROERANON WITH 22UITERSMOUR TSUITERS HOUR 22 UTERSMOUR SOUITERSIHOUR ERRONN PAG SEVES UPTO SERVES UPTO Seneeupro Steves UPTO ANO Waren arse SHS PEOPLE SO PEOPLE iS PEOPLE S PEOPLE COD WATER 4 2 LITERS 1 5 LITERS 2LITERS 2LITERS OOLING GAS Rida LOAD GAs 329 VOLTAGE 127V OR 220V 60HZ VOLTAGE aw asw asw 100w NOMINAL PRESSURE MINAN PRESSURE OR NE HYDRAULIC NETWORR 0 196MPa 20 meters of water column 0 029MPa to 0 392MPa 3 to 40 mot
3. used in this type of operation can cause internal damage to the unitand even contamination The material used in manufacturing the filter is not dangerous and can be disposed of in common garbage NBR 10004 2004 WATER INTAKE 2 10 HOW TO CHANGE THE 2 IN 1 FILTER MSoft tet To change the filter follow the procedures below 1 Close the water meter and open the room temperature and cold water taps to relieve the pressure inside the device 2 Disconnect the device from the electrical outlet 3 Exclusive to Star Slim and Plus models Loosen the plastic screw C one to two turns rotate the filter B anti clockwise using the fins F to disconnect it from its upper coupling A 3 1 Exclusive to the fit model 3 Remove the right side lid E loosen the plastic screw C one to two turns remove the water inlet pipe D rotate the filter B counterclockwise using the fins F ofthe filter body to disconnect it from the coupling Fig 4 4 Exclusive to Star Slim and Plus models Tit the filter B out of its compartment and pullit upward disengaging it from the input water tube D fig 3 4 1 Exclusive to the fit model Pull the filter A out of its compartment 5 Replace the filter 6 Screw iton in the reverse order from the previous items 7 Open the water meter check for leaks and remove at least twenty 20 liters of natural water to eliminate possible carbon particles We remind you that the carb
4. 3 TECHNICAL ASSISTENCE MASoftt tet Your Soft purifier will rarely have problems of and electrical or mechanical nature but if some irregularity occurs check under item 15 PROBLEMS AND SOLUTIONS for possible causes and corrections that can be adopted If the problem is not corrected contact your local Authorized Everest Dealer NI Note The Warranty does not cover the following items 1 Equipment installation 2 Assistance to households more than 30 km away from the Technical Assistance Center 3 Replacement of filter due to saturation 4 Replacement of external hoses connections stopcocks and pressure regulating valve used in the product installation 5 Calls without justification such as lack of water electricity etc 14 CERTIFICATION MSOFE tarat SAFETY n compliance with Ordinance No 191 of INMETRO from December 10 2003 which established requirements for construction and electrical safety for drinking fountains and purifiers etc the certification of these products became mandatory This process establishes the carrying out of tests in laboratories as well as the evaluation of the manufacturer s quality management system by a certifying body accredited by INMETRO Our cold and natural water purifiers SOFT STAR SLIM SOFT SOFT FIT and SOFT PLUS have been certified by Bureau Veritas and have the conformity identification seal established by INMETRO HEALTH The market for water purifiers has a specifi
5. USER S MANUAL Congratulations on choosing to live healthier lives Soft by Everest MSofty WATER PURIFIERS COLD AND ROOM TEMPERATURE _a Soft vy Everest WARRANTY CERTIFICATE v Soft OPs Cistar by Everest Osum JFit White Black 127V 60Hz 220V 60Hz 127V 60Hz 220V 60Hz Silver Silver C Cherry Cherry 127V 60Hz 220V 60Hz 127VI60H2 220V 60Hz CERTIFICATE N ABRIL2015 REV 150410 Suggestions Information and complaints Call 0800 024 0332 send a FAX 21 2591 4798 or by e mail everest everest ind br To expedite customer service please have the machine model the invoice and serial number at hand EVEREST REFRIGERACAO INDUSTRIA E COMERCIO LTDA RUA CARDOSO QUINT O 914 TOMAS COELHO RIO DE JANEIRO RJ CEP 21381 460 TEL 21 2597 0332 FAX 21 2591 4798 SAC 0800 024 0332 www everest ind br everest everest ind br White J Black 2 GIDE Everest Refrigera o Ind stria e Com rcio Ltd congratulates you for the choice you have made in purchasing your Soft Water Purifier In our industry everything was done so that your water purifier has the best performance for many years and your collaboration will be necessary first by reading this manual carefully and then using it as recommended below When you receive your Soft carefully check that itis in perfect condition If there is any damage or concerns please contact your dealer or the
6. a 100 mea manually regulating itself at an outlet pressure of 0 294 MPa 30 mca see nominal pressure Important Even in a water system with pressure within the maximum limit for your appliance 0 392 MPa or 40 mea we recommend that you check whether a sudden increase in water pressure water hammer could occur because this phenomenon can cause irreversible damage to the filter and the entire internal system of the appliance In this case the installation of a pressure regulating valve becomes necessary 4 REGULATING VALVE CONNECTION ADJUSTMENT Allows the installation of the pressure regulating valve which has a wall stopcock filter 5 FILTER METER HOSE CONNECTION It can be installed in a domestic wall filter water meter or anywhere else in your plumbing system 6 PRE FILTER Used to prevent premature saturation of the 2in 1 filter by excess sediment The Pre filter traps particles above 104 NA 07 ELECTRICAL CONNECTION MSoft ter This product complies with international safety standards The plug used allows your purifier to be grounded thus avoiding the occurrence of electrical discharges If the electrical installation is not in compliance the installation is carried out at the user s own risk The electrical outlet must be robust and unique tripolar Before connecting your device check that the voltage 127 or 220 V is in accordance with the plug Do not connect the appliance to extension cabl
7. ber that these precautions should be taken only during the installation of your appliance or when changing your water filter Once the water output of your device has been normalized connect it to the power outlet and wait approximately 60 minutes the time required for the device to freeze the water in its internal tank after this itis ready to be used Your Soft Water Purifier has a thermostat to control water temperature at an average of 8 C already preset at the factory The heating up of the cabinet in your machine is normal This heating up occurs due to heat exchange between the condenser and the cabinet For correct operation itneeds to be installed in a place with good ventilation The device makes sounds like the one when the ice tray turns this is normal and is caused by the layer of ice formed in the refrigerator evaporator as well as the compressor which produces the noise characteristic of an electric motor which means that the compressor is in operation NI Only for the Fit and Plus models These models are equipped with a mi better efficiency in the cooling system The operating noise of this mini and does not denote a problem NA 091 KNOW YOUR FILTRATION SYSTEM AI SESoft ema WHEN TO CHANGE THE FILTER Designed for use with drinking water i e treated by a water supply company your 2 in 1 filter aims to retain impurities contained therein as well as reduce chlorine odors and flavors to the water Int
8. c standard for assessing conformity NBR 16 098 2012 which evaluates the performance and efficiency of the appliances through tests performed in a laboratory accredited by INMETRO Brazilian National Institute of Metrology Quality and Technology The HEALTH seal of compliance features that Everest ensures the quality of the water that is supplied The performance and efficiency tests for the Soft Water Purifiers has the following classifications NI Performance Tests Particle retention Reduction of free chlorine C l gt 75 Bacteriological efficiency Not applicable The tests were performed according to NBR 16 098 2012 Pll gt 5a lt 15um A 15 PROBLEMS AND SOLUTIONS MSoft tort SYMPTOM PROBABLE CAUSE SOLUTION 1 No water coming Water stopcock closed or lack Check the water meter out of the nozzle of water or water supply Saturated filter Change the filter Check the water meter 2 Water outlet nozzle Partially closed water meter Correct the positioning of with small leak Choked water hose Saturated filter the water hose Low water network pressure Change the filter Obstructed nozzle Check Clean the nozzle fig 5 3 Device does not Electrical voltage output very Install voltage stabilizer chill or has low high or very low in this case minimum 200W output the compressor will give Check several successive sta
9. dior electrical pipework If there is doubt about the fulfillment of these conditions we do not recommend installing the product on the wall In any case the manufacturer its dealers and representatives disclaim any responsibility regarding the installation of this product on the wall For wall mounting use the template for drilling attach the brackets to the 8mm wall plugs S8 and the screws that came with the device using a 0 8mm or 5 16 concrete drill fig 2 Remove the rubber cap that protects the water hose and then suspend the Soft and fix it onto the brackets Let the machine move down gently making sure that the assembly is firmly in place TEAR FOR FITTING DEVICE S8 BUSHINGS WALL SUPPORT 4 06 OPTIONAL ITEMS MSoft taret 1 HOSE EXTENSION KIT Optional hose extension comprising 03 meters of double sided non toxic PE EVAhose 2 CONNECTION T 1 2 HOSE Allow the connection of your purifier at the point used for a tap 3 PRESSURE REGULATING VALVE Your Soft Water Purifier was designed to work in a water network with pressure from 0 029 MPa to 0 392 MPa 3 40 mea Pressures over 40 meters of water column cause damage to your equipment In this case it becomes necessary to install a pressure regulating valve which was developed especially for use in Everest water purifiers This valve can work in water networks with pressure up to 0 98 MP
10. ernally it has a cartridge produced in non toxic polypropylene by the Melt Blown system which consists in the overlapping of woven microfibers It has the characteristic of retaining impurities greater than 5u on OUTPUT os surfaca and roughout hs tiokness thereby giving it OF WATER J greater durability After filtration the water enters the activated carbon i stage which reduces chlorine odors and flavors to the water by the adsorption process This carbon is impregnated with colloidal silver whose bacteriostatic action inhibits the proliferation of microorganisms inside it Your filter has an average service life of 4 000 liters 9 12 months which may be reduced depending on the quality impurities chlorine content etc of the water used dally If the flow of water decreases appreciably or changes are observed in the taste or odor of the water this indicates saturation of the filter element and or the activated carbon making the changing of the filter necessary in any case Between 9 and 12 months for security reasons your filter should be replaced even if it has no changes as described above The reason for this is that the biofilm formed internally by trapped organic and inorganic impurities as well as the reduction in the bacteriostatic efficiency will compromise the quality of the water supplied Due to their construction characteristics the 2 in 1 filter does not allow backwash because the water
11. es or with other cables at the same outlet Allowable voltage range is For 127V between 100 and 140V For 220V between 198 and 242V Voltage outside the established limits may cause the compressor to blow which in this case will not be covered by warranty If the voltage is outside the established limits itwill be necessary to install a surge protector with an output not inferior to 200W 08 OPERATION NESOft teut Before connecting the appliance make sure that the electrical voltage supply is correct With the device connected to the water network it s time to fill up the water tank Place a container under the water outlet nozzle and open the natural water tap Due to the presence of fine particles of activated carbon from the filter at the beginning of the operation the water may be slightly cloudy This is normal and is caused by powdered activated carbon that forms during the shipping and handling of your appliance Let the water run out 20 liters until it is crystal clear and then open the cold water tap waiting for the water to come out clear The presence of micro bubbles of air in the water is normal and may last several days The carbon used in the filter is harmless to human health Note If a decrease is observed in water flow after the initial disposal remove the water outlet Nozzle and rinse it with water to remove small grains of carbon that may be obstructing the passage of water To remove the Nozzle see fig 5 Remem
12. mend shutting the water inlet and disconnecting your appliance from the electrical outlet 3 Upon return discard 2 liters of water from each of the taps 4 Whenever handling the water outlet nozzle do so with clean hands to maintain water quality The cleaning of the nozzle can be done with slightly dampened cotton with alcohol gel After cleaning the nozzle dry properly and remove any excess alcohol discarding a glass of water To access the inside of the Nozzle follow fig 6 Be careful not to loosen the two stainless steel screens Cleaning should be carried out if changes in the flow of the water outlet or accumulation of impurities are observed TO REMOVE THE WATER OUTLET NOZZLE ROTATE IT COUNTER CLOCKWISE AND PULL IT DOWN USE THE FIN FOR BETTER GRIP WHEN CARRYING OUT THE OPERATION N BOTTOM VIEW SIDE VIEW DISMANTLE THE EQUIPMENT FOR THE BEST ACCESS TO ALL PARTS WE SUGGEST THAT THIS CLEANING BE DONE BY AN AUTHORIZED TECHNICIAN SCREEN FIXING WASHER STAINLESS STEEL SCREENS NOBLE eri omr fig 6 5 We recommend that every 2 years the device be sanitized by an authorized technical assistant Important Discard 2 liters of water from any tap after cleaning 6 To clean the Drip tray remove it following the drawing below fig 7 1 PRESS THE LEFT PART OF 2 HAVING DONE THIS THE DRIP TRAY COVER TO PULL THE DRIP TRAY REMOVE IT TO RELEASE IT 1
13. on used in the filter is harmless to human health 5 Reconnect the device to the main power THE CHANGE OF THE FILTERING ELEMENT DOES NEITHER CAUSE ANY ANOMALY NOR IMPACTS THE FUNCTIONING OF THE COOLING SYSTEM OF YOUR PURIFIER 2 11 MAINTENANCE MSoft cont For external cleaning do not use abrasive substances soaps detergents chlorine caustic soaps alcohol or solvents They attack the paintwork on the casing and the plastic Clean your appliance only with a damp cloth and neutral detergent and dry it thoroughly Regularly clean the rear gas condenser with a soft brush or vacuum cleaner The change of the power cord should only be performed by the manufacturer Authorized Technical Service Network or by a qualified professional in order to avoid risks to the user and damage to your equipment Ifthere is a need to remove the front panel for any maintenance this operation can only be performed by the manufacturer or the Authorized Technical Service Network Z GBT Soft tone When cleaning the water tank to supply the water network always close the water inlet stopcock of your Baby Soft Purifier so there is no excessively dirty water getting in If this care is not taken the service life of your filter will be compromised 1 Itis recommended to discard the first glass of water daily from any one of the taps room temperature and cold 2 When there is prolonged absence vacation travel etc we recom
14. ors of water column TEWORRING SC a 42 C sft ELEMENT 4 000 LITERS RECOMMENDED FLOW 0 75 LITERS MINUTE NOPE DENCE 1 6 LITERS 2 LITERS 2 5 LITERS 2 5 LITERS FOR PANCIA TEST 4 000 LITERS 04 GET TO KNOW YOUR SOFT NESoft tes WALL BRACKET FILTER gt FITTING HOLES COMPARTMENT j COMPARTMENT COVER Nt WATER INLET HOSE G D as 14 EXTERNAL GAS THREAD FINISHING S surp c rn MESTE 2 1N 1 FILTER ReaR stoP CA A b t A NATURAL WATER TAP U lw f FILTER COMPARTMENT wear DEVICE FOR POINT WATER gre OF USE POU REMOVABLE APPLIANCE FOR DRIP TRAY INTERNAL USE IPX0 MM 05 INSTALLATION LOCATION MESOft tarat Your Soft Water Purifier has been provided with an installation kit consisting of 02 meters of non toxic plastic hose already connected to the device 01 Softwater inlet water meter 028 mm Bushings S8 with corresponding screws 01 set containing 2 brackets and one template for drilling Your Soft was provided with a non toxic hose and a water meter for hydraulic connection The use of any other type of hose should be avoided because those found on the market are generally toxic and there is a strong possibility of them causing the water to have an unpleasant taste Othe Soft water inlet water meter fig 1 may be installed at a hydraulic installation point installation
15. rest disclaims all responsibility and this Warranty is void if the equipment suffers damage from falls is linked to an improper water network or not compatible with the equipment by natural phenomena lightning landslides floods etc usage not in accordance with the instruction manual showing signs of misuse due to introduction of foreign objects or liquids inside it or has been tampered with repaired or adjusted by unauthorized third parties The Warranty will also be considered void if the Tax Invoice from the Purchase or this Certificate present erasures and or alterations All replaced parts shall be the property of rat The Warranty does not cover the following items Installation of the product Assistance to households more than 30 km away from the Technical Assistance Center Replacement of filt Replacement of external hoses connections stopcocks and pressure regulating valve used in the product installation Calls without justification such as lack of water electricity inadequate installations etc EVEREST reserves the right to change the specifications and designs of its products without notice due to technical improvements
16. rts Correct allowing greater without working air circulation Excess consumption of cold ee pa water specified by the model Everest Au at tem 3 TECHNICAL DATA Installation locations without air circulation usually fitted appliances Mini fan not working applies to Plus and Fit models 4 Water leak in the filter compartment Plastic screw not tight enough Check the tightness of 2 in 1 fiter not tight enough the plastic screw in the filer Check the tightness of the filter with the coupling 5 Water outside drinking standards Microbiological contamination Check the drinkability in the water network NOTE If any of the above items are verified by technical assistance the costs shall be borne by the user WARRANTY CERTIFICATE We guarantee this Eroraf device to be free from defects as regards materials and workmanship for a period of 03 three months by law plus 09 nine additional months granted by makinga total of 12 twelve months for the first user starting from the date of issue of the Tax Invoice provided it is used in normal and recommended conditions During the term of the Warranty we undertake to replace or repair free of charge any defective parts when examination reveals the existence of defects in material or workmanship Only authorized dealers in the attached list are allowed to carry out service under Warranty Eve
Download Pdf Manuals
Related Search