User's Manual
Contents
1. wy REMOTE KEYPAD RKD500 T RKDS500 ANALOG WAY USER S MANUAL Chapter 1 INTRODUCTION 1 1 SUPPLIED EQUIPMENT e 1 REMOTE KEYPAD RKD500 T or RKD500 e Power supply e Remote cable DB9 M F 3 m 10 ft e update cable DB9 F F 0 9 m 3 ft e 2 white labels to rename the input selection buttons e User s manual 1 2 GENERAL INFORMATION The Remote Keypad is a control device for the Octo Vue Series Octo Vue FX Octo Vue Fade amp Octo Vue It s also compatible with switchers of the Octo amp Quattro Series Provided with a LCD screen a T Bar and a lot of direct touch control the Remote Keypad offers a complete control of the device at which it is connected The Remote Keypad is compact easy to use and easy to connect via its RS232 communication port or via its optional LAN communication port The Remote Keypad can be update and thus it can follow the progress of the controlled devices RKDS500 T only 1 3 REFERENCES amp OPTIONS REFERENCES DESIGNATIONS RKD500 T Remote Keypad with T Bar RKD500 Remote Keypad OPT LAN Optional LAN communication port 1 4 FRONT PANEL DESCRIPTION Fn Secondary function selection button gt Button blinking function active NOTE The Fn function will be inactivated after another push on this button or after doing an adjustment or automatically after 5 seconds delay INPUT SELECTION Pre selection of the 8 input sources 1 to 8 gt Button turns ON source2. another pre selection PREVIEW FRAME Frames selection gt Button turns ON FRAME displayed on the MAIN output gt Button blinking slowly FRAME displayed on the PREVIEW output PIP ADJUST WINDOW PIP window adjustment Button turns ON SOURCE PIP source adjustment Button blinking quickly POS Position adjustment of the PIP window or PIP source Button turns ON SIZE Size adjustment of the PIP window or PIP source Button blinking quickly H Horizontal adjustment of the PIP or logo Adjust with the knob 4 gt Button turns ON y Vertical adjustment of the PIP or logo Adjust with the knob 4 gt Button blinking quickly LOGO ADJUST 1 Logo 1 selection for adjusting the position on the MAIN or PREVIEW output depending on the PREVIEW MAIN button 2 Logo 2 selection for adjusting the position on the MAIN or PREVIEW output depending on the PREVIEW MAIN button ON OFF Displays ON or displays OFF the logos 1 amp 2 on the MAIN or PREVIEW output depending on the PREVIEW MAIN button VOLUME Volume adjustment of the MAIN output Adjust with the knob 4 gt gt Button turns ON Volume adjustment in progress MUTE Audio mute of the MAIN output Adjust with the knob Button blinking slowly Mute activated Button turns OFF Mute inactivated CONTROL 4 gt Allows to scroll thru the different menus in Control mode EXIT MENU Switches between Status and Control mode ENTER Validates a
3. displayed on the MAIN output gt Button blinking slowly source displayed on the PREVIEW output TAKE Allows to display the pre selected source onto the MAIN output with the selected effect T BAR Allows fading manually between sources EFFECTS Selection of the 6 USER effect presets NOTE USER presets 4 5 amp 6 can be selected only when Fn 1s active gt Button USER 1 USER 4 turns ON USER 1 selected gt Button USER 1 USER 4 blinking slowly USER 4 selected gt Button USER 1 USER 4 turns OFF USER 1 or USER 4 effect not available IMPORTANT The CUT FADE PIP and TITLE effects are available in SEAMLESS mode and only between the reference computer input and the other input PREVIEW MAIN Outputs selection for the adjustment gt Button turns ON PREVIEW output selected gt Button blinking slowly MAIN output selected This function can be selected only when Fn is activated REMOTE KEYPAD RKD500 T RKD500 PAGE 1 EDITION 01 07 1 4 FRONT PANEL DESCRIPTION continued FREEZE Freezes the MAIN or PREVIEW output depending on the PREVIEW MAIN button BLACK Display a black screen on the MAIN or PREVIEW output depending on the PREVIEW MAIN button gt Button turns ON FREEZE activated gt Button blinking quickly BACK activated NOTE The FREEZE will be inactivated after another push on the FREEZE button THE BLACK will be inactivated after another push on the BLACK button or after
4. ring the warranty period Analog Way will at its discretion repair or replace the defective unit including free material and labor This warranty does not apply if the product has been improperly installed or abused handled with improper care used or stocked in abnormal conditions modified opened damaged by fire war or Natural disasters Acts of God In no way shall Analog Way be responsible for direct or indirect loss of profit or consequential damages resulting from any defect in this product In case of any problem get the serial number of the unit a description of the problem and then call your authorized dealer REMOTE KEYPAD RKDS500 T RKDS00 PAGE 3 EDITION 01 07
5. selected item This function can be selected only when Fn is activated 1 5 REAR PANEL DESCRIPTION DC IN DC power connector RS 232 RS 232 communication port LAN Optional LAN communication port Chapter 2 CONNECTING 2 1 CONNECTING THE RKD500 WITH THE RS 232 PORT Turn OFF the controlled device rear panel switch of the Octo Quattro Connect the RS 232 connector DB9 female of the controlled device to the DB9 male connector of the REMOTE KEYPAD with the supplied DB9 M F cable Turn ON the controlled device rear panel switch NOTE The REMOTE KEYPAD is powered by the contolled device via its DB9 RS 232 connector Speed transmission 9600 bauds 8 data bits 1 stop bit no parity bit no flow control Pin out RECEIVE DATA Rx GROUND Gnd DB9 female Rear panel of the controlled device 2 2 CONNECTING THE RKD500 TO A NETWORK LAN Connect the power supply to a power outlet and to the DC IN connector rear panel Connect the REMOTE KEYPAD to your network according to your installation REMOTE KEYPAD RKD500 T RKD500 PAGE 2 EDITION 01 07 Chapter 3 UPDATING THE REMOTE KEYPAD The REMOTE KEYPAD can be updated thanks a COMPUTER PC via its RS 232 communication port only 3 1 CONNECTIONS Connect the RS 232 connector of the REMOTE KEYPAD to the SERIAL port of your COMPUTER with the update cable DB9 M M crossed cable Connect the power supply of the REMOTE KEYPAD to a power ou
6. tlet 3 2 UPDATE INSTRUCTIONS Open the file RKD500 Updater in Start gt Program gt ANALOGWAY gt RKD500 In the Port menu select the COM port connected to the device Click on START on the SOFTWARE Press the ENTER button of the RKD500 and connect simultaneously the DC plug of the power supply to the REMOTE KEYPAD DC IN connector The LCD screen displays Downloading and the upgrade will start Then you can release the ENTER button When the software displays Program operation completed disconnect the update cable and the DC plug Then connect again the DC plug to the RK D500 Click on the Quit button to close the update SOFTWARE NOTE The updater files are available on our web site hittp Avww analogway com OOO Chapter 4 TECHNICAL SPECIFICATIONS Power Supply 9 Vdc Storage Temperature 40 C to 70 C 40 F to 158 F Maximum ambient operating temperature lt 50 C lt 122 F Hygrometry 10 to 80 without condensation Dimensions RKD500 T W 220 x D 130 x H 102 mm W 8 9 x D 5 1 x H 4 Rackmount compatible 3U height 2U width RKD500 W 220 x D 130 x H 67 mm W 8 9 x D 5 1 x H 2 6 Rackmount compatible 3U height 2U width Weight 1 kg 2 2 Ibs Chapter 5 WARRANTY Analog Way warrants the product against any defects in material and workmanship for a period of three years from the date of purchase back to the factory In the event of any malfunction du
Download Pdf Manuals
Related Search