Fina 320B
Contents
1. Ink Air Filter Channel j Assitant gt Print Head A Ink Tank Valve Filter Floating Switch Air Filter Ink Pump OutPut Input Pump Light Data Signal Pressure Signal Air Pump Main Tank Power Chart 8 2 1 Ink supply and cleaning system diagram 8 3 Working Principle of Positive Pressure Cleaning When you press clean button the cleaning signal will be transfer to assistant board and drive the air pump and ink pumps air pump starts running and transfers air pressure to valve the air pressure raises and transfers to assistant ink tanks through air channels With pressure got from the air pump ink will be purged through the head and nozzles At the same time ink pump pumps ink to assistant ink tanks from main ink tanks provides ink for print heads cleaning SB FINA320B User s Manual 8 4 Operation Description of automatically Positive Pressure Cleaning Flash plate Switch handle Cleaning roller Waste Ink Tank Waste ink tube Summary The automatically Positive Pressure Cleaning have two mode 8 4 1 Auto clean One cycle of auto clean process have below steps Air pump work waiting 50 seconds cleaning roller go up Print carriage go left Waiting and Print carriage Cleaning roller End lt flush go right go down The total time of the auto clean process spend 80 seconds The LCD will display BUSY and there2. is still 2 Heat Heat Heating status displays Status Status The LCD display details as below FH Menu eat Status FH Pre P H Tem 00 00 00 Offline Set 00 00 00 Item Tem displays actual temperature Item Set displays setup temperature FH means front and rear heater Pre means middle plate heater FINA320B no this option P H means print head heater FINA320B User s Manual 3 Cleaning Firing The LCD display details as below Tool 1 Firing 2 Jam Test offline 3 Clean Post 4 Home Post 5 Clean Offline 6 Clean heavy Press ENTER key to execute the operation Busy flashes on the LCD P Hs spray downward to prevent nozzle clogs The LCD stops flashing after firing finishes Press ENTER key again to execute P H firing one more time if necessary The volume of ink fired should be set in submenu Firing Vol under menu Print Para Press ENTER key to execute the operation of test printing Press ENTER key to execute the operation of moving P H carriage to left Clean capping position and waiting for cap the print head Post Home Post Press ENTER key execute the operation of returning the P H carriage to original position Clean Press ENTER key execute the operation of a total auto clean process one time Please see 8 4 1 for detail Clean Press ENTER key execute the operation of a total auto heavy clean process one heavy time Please see 8 4 2 for detail 220 FINA320B User s Manual
3. VIII iii I 1141444711 AR R Va VaVaVAVaVaVAVAVAVA LM i 1142447272 EE A 1414447744 HU A i 174447744 ET 3 111124147442 HH VAVAVAVAVAVAVAVAVAVA d na KIR 310204244444 Trt th A VIZIZ ZIZZ ZZ ZZ T AAA 2 amp o EN N N N N N N N N NININ NIN USA PESOS SS TAS KSS ASS SAS KSS ASS SAS SAS SAS AS SAS ASS ss FE ee llow e enta ag m N N SS N N RR N 2 VA Le EA 7 Va a 2 N Z z OR VI E WA Fr BA 2 7 7 Va 7 zZ z 7 2 FINA320B User s Manual 24 With 3PASS 4PASS 6PASS 8PASS mode We use the normal iamge for feeding compensation You should reduce the feeding compensation number if there is some blank in the image and add the feeding compensation number if there is overlap in the image ATTENTION The feeding compensation is different for different media CHAPTER 11 MAINTENANCE 11 1 Daily Maintenance Daily maintenance is very important for normal workstation of the printer Daily maintenance includes OMaintenance after each printing 4 Erasure dried ink from print head surface with flush solution 4 Restore the jammed nozzles before next printing Each 8 hours 4 Oil the print head rail and clean the dust from it once each 8 hours O Daily work Check waste ink tank cleanup if necessary Check the waste ink groove on the startup position and clean it if necessary Che
4. 3 1 3 How to connect the print head cable 1 Insert one end of print head cable on the PH control board and the other end of print head cable is inserted to the print head CAUTION The connector of the print head and the data cable only have one direction Please confirm the direction is true before you insert the date cable to the print head connector Or else it will cause the damage of the print head O x FINA320B User s Manual Please connect all of the 8 print head cable based on the right picture PH Control Board2 PH Control Boardl K4 K3 K2 Kl Y4 Y3 Y2 YIJ Mi M3 M2 Ml C4 C3 C2 Cl DUUDUUUUUDODODUUUUTL PH Carriage Chart 3 3 Connection of print head cable 11 FINA320B User s Manual 3 2 Attention before Turning on the printer 1 In order to clean print head easily please prepare following items e Flush solution e Non woven fabric 2 In order to inspect temperature and humidity of printing environment please prepare relative measurers Requirement for environment e Temperature 20 C 30 C e Humidity 40 80 3 Power supply e You may select AC 110V or 220V for different countries or regions e Control power supply AC 100 240V 50 60HZ e Heating power supply AC 100 OR 240V 50 60HZ AC 100 V optional e Feeding power supply AC 100 OR 240V 50 60HZ AC 100 V optional Please choose the type of power shown on the printer in case of damage to the printer e Ma
5. FINA320B N Warning Change those parameters becarelly o Chart 10 5 Warning dialog box After pressing Yes you can see the dialogue box Chart 10 6 Important setup Important Setup Vertical Compensation o 0 l Ingore Horizontal Space Ingore Vertical Space Feed Compensation jn Ok 54 FINA320B User s Manual 1 Parameter of nozzle installation Adjust the head position and overlapping of four colors Vertical space the vertical space between print heads of all kinds color It s used for emendating vertical space overlapping of all kinds color print heads Horizontal space the horizontal space between every print head It s used for emendating overlapping of four colors The print head range chart lists as below la Ug D ey ey do 05 K3 Kl Y3 Y1 M3 M1 C3 C1 PH Carriage Chart 10 7 Print head range chart 2 BID Rectangle To adjust the BID rectangle tolerance value Generally modify BID rectangle value first in BID adjust If the difference is not big adjust here 3 Ignore horizontal and vertical deviation No adjustment Only for inspect printer status 4 Feed Compensate Used to adjust the feeding on the Y direction The amount of feeding is different with different Pass After adjusting it can correspond relevant rectangle automatically by different printing mode and media types 200 E FINA320B User s Manual 10 3 Print h
6. User s Manual lt EN gt FINA320B 600001810 Version 1 0 FINA320B User s Manual Thank you very much for purchasing our printer In order to use this printer correctly and safely and understand this product s capability please read this manual carefully The manual includes equipment structure description technical parameters operation manual safety information and application of software etc This manual is subject to change without notice 9 Contents here in contained are believed to be correct however please contact us if you find any error or something not clear enough September 2007 Version 1 0 FINA320B User s Manual Clean Post FINA320B User s Manual Chapter 1 Safety information Before use your FINA320B Digital Printer Hereafter refer to printer please read following safety information Pay attention to the cautions on the Printer 1 1 Important Safety Information e Do not block the hole on the cover e Do not insert any object into the Printer groove Don t let any kind of liquid splash into Printer e Only use the power supply according to the label You may choose either AC 110V or 220V for different countries and regions e Connect all the equipment to a properly grounded socket Avoid the socket in the same circuit with copy machine or air conditioner e Avoidto using the socket controlled by the wall switch or by auto timer e Please keep Printer away f
7. Assistant ink bottle Y 4 Assistant ink bottle K 5 Safety bottle Chart 7 3 4 Assistant ink tanks 42 FINA320B User s Manual Chart 7 3 5 Assistant board 7 4 Function Description 1 This system work automatically and control several pumps to supply ink simultaneously When printer is power on ink pump starts automatically to pump ink to assistant ink tanks from main ink tanks 2 The system works with perfect alarm and protection function If any problem occurred in any pump it will alarm and indicate which one is in trouble on the LCD and the troubled one will not affect others Ink filter switches get signals through serial ports 4 It is easy to connect it to other systems All floating switches signals can be input by serial port or parallel port 5 Main controller consists of micro CPU which can check signals using software to filter out the false ones which is helpful to make system work more reliably 43 FINA320B User s Manual Ls The ink pumping limit is controlled by intelligent control system of main control board in case that the electric circuit will cause ink supply shortage 7 5 Operation Description Note Please read descriptions carefully for ink supply system cleaning system and Ink Control system before starting the following operations 1 As soon as the printer s connected with power system detects floating switch signal automatically and drives ink pumps to pump ink
8. Auto Print heads Cleaning and Capping system Print head Height 2 5 mm 4 5 mm above media adjustable Operation Platforms Multi operation platforms Window2000 XP etc USB2 0 interface Window2000 NT XP etc Normal FINA RIP support multiform third party RIP AC100 Ek 240V 50HZ 60HZ Working Environment Temperature 20 C 28 C Humidity 40 70 Printer Size Weight Net Weight 3900mm L X 870mm W X 1100mm H 330KG Gross 4500mm L X 925mm W X 1200mm H 368KG Media Feeding Auto Media Feeding amp Take up system Take up is OPTIONAL The parameters above are subject to change without notice FINA320B User s Manual CHAPTER 3 EQUIPMENT ASSEMBLY AND ADJUSTMENT 3 1 Assemble Printer 3 1 1 How to install the dry blower assy T MEE FINA320B User s Manual 3 1 2 How to install the print head D FINA320B User s Manual Print Head cable In tube Print head clamp Out tube Method and Steps a Insert Xaar130 600 print head to the print head frame downwards at first b Insert the print head fixing dowel to the corresponding dowel hole for fixing print head c Put the 2 screws with the Xaar130 600 print head on screw holes which is on the upper and nether middle part of the frame d Tighten the 2 screws and draw the fixing dowel out of the frame e Put the sheeting between the two print head and fixed with screws which is 2 5 10
9. 4 Print Print Post The LCD display details as below Para Menu Print Pos mm Offline 0298 Number string XX XX flashed on the LCD Here press and gt key to move the cursor position over the number string and press f or Y key to increase or reduce the value of the flashing number Press ENTER to save the number as print position Images and test print start from this position Here press key combination FUNC f or key to move the media forward or backward press key combination FUNC key to move the P H carriage to printing position It will tell the position set well or not Press any key to return the P H carriage to original position Bi dir Adj Press ENTER key and the LCD displays as below Menu 2 Bi dir Adj Offline 0050 This function is used to adjust bi direction printing to ensure bi direction printing quality 29 FINA320B User s Manual Print This function is used to adjust the scan speed of the P H carriage The LCD Speed displays details as below Print Speed Offline Press f or key to select from the 3 options High scan speed will reduce printing quality Low scan speed will increase printing quality but reduce printing speed The suggestion is Norm Feed The LCD displays details similar to Print speed Norm flashes as the default Speed option Press or key to select from the 3 options The suggestion is Norm Firing Vol XXXX flashes
10. on the LCD Pressf or Y key to increase or reduce the value by 1 The default value of Firing Vol is 20 This value is the firing volume of P Hs for auto spray and printing after cleaning that means all nozzles are unclogged Flash Numbers are used for flash mode setting Mode 0 stands for P H does not flash during printing The LCD displays details as below 6 Flash Mode 0030 When the value is 1 it stands for pint head flashing in original position after printing 1Pass When the value is 2 it stands for pint head flashing in original position after printing 2Pass When the value is 30 it stands for print head flashing in original position after printing 30Pass The biggest value can reach to 30 30 FINA320B User s Manual PH Volt This function is used to set Voltage of P Hs The LCD displays details as below Set Menu 1 PH 1 Voltage 2 PH 2 Voltage 3 PH 3 Voltage Offline 4 PH 4 Voltage 5 PH 5 Voltage 6 PH 6 Voltage 7 PH 7 Voltage 8 PH 8 Voltage 9 PH 9 Voltage 10PH 10Voltage 11PH 11 Voltage 12PH 12Voltage 13PH 13Voltage 14PH 14Voltage 15PH 15Voltage 16PH 16Voltage 17PH 17Voltage 18PH 18Voltage In this printer print head 1 2 3 45 stand for C color print head print head 5 6 7 8 stand for M color print head print head 9 10 11 12 stand for Y color print head print head 13 14 15 16 stand for K color print head Go on pressing ENTER the LCD shows 1 PH 1 Voltage 0068 Offline 0137 3
11. the route switch 21 Sub tank provide ink to print head 22 Ink filter Filter impurity in ink 23 Ink pump provide ink from main tank to sub tank 24 Valve Automatically control the air route 25 Current leakage protector Prevent electric leakage of heating board 26 Printer Interface USB2 0 interface provide the data communication to printer and computer 27 Heating Power Socket Provide power for heater 28 Power Socket Provide power for printer 19 FINA320B User s Manual 220 FINA320B User s Manual CHAPTER 5 USAGE AND MAINTAINS OF PRINT HEAD 5 1 Usage of Print head J Print head Out tube 4 Ink tube cap ee Fitting Chart 5 1 Print head 1 Flush humectants out of print head To moisturize print head lots of humectants are injected into the head before it is used The humectants must be flushed out for the first using Before fix the head on the print head frame do the steps as follows Joint a filter on the In tube of the head and then joint an injector which fills with flush solution on the filter Inject 10 20 ml flush solution to the head to eject the humectants inside Then fill the head with flush solution to dissolve the humectants completely within 5 10 minutes Finally flush the head with about 30ml flush solution to eliminate the humectants completely Make sure to operate on a stable and clean platform Cautions a Clean platform for c
12. value once set by the technician Set the biggest distance in scanning direction Printer It s better not to change this value once set by the technician Width 34 FINA320B User s Manual 6 Engineer Press ENTER to execute the operation The LCD displays details as below Set Moving Test Moving Test Offline 0000 And P H carriage moves back and forth to simulate printing but P H not spray It s used for mechanical test The number on the LCD indicates times the P H carriage moves back and forth Reset the parameters to default setting Default Press key combination of FUNC ENTER to execute the operation Se It had better not to execute this operation except for the technicians It is used for speed test of Y motion Y Test It had better not to execute this operation except for the technicians Speed X Test It is used for speed test of X motion Speed It had better not to execute this operation except for the technicians EF value setting Each Xaar130 head has its own EF value Manufacture always provides a standard EF value which is captured under standard condition Users input this value at column Voltage Usually the printing effect is good The value is marked on the head User should write down the EF value before you install the PH then put the value into the setting of the main board See menu tree print pare PH Volt set If the voltage is too high it produces the satellites and i
13. 0 4 Print setting dialog box This function is to set the printing parameter print mode uni direction BID and the color of ink Note Usually the four colors should all be selected Only when the engineer adjusts the position of head one certain color is chosen to modify the printing parameter P H QTY This software support 4 and 8 print head optional PRINT MODE There are 6 modes for choosing Test mode 360 360 dpi 360 720 dpi 360 1080 dpi 720 720 dpi 720 1080 dpi 720 1440 dpi Test mode Horizontal printing precision is 360 dpi Printer will print 360 dpi precision once at feeding direction 360 360 Printing precision is 360 dpi Printer will print 180 dpi precision two times at feeding direction 360 720 Printing precision is 360 dpi Printer will print 180 dpi precision four times at feeding direction 360 1080 Printing precision is 360 dpi Printer will print 180 dpi precision six times at feeding direction 720 720 Printing precision is 360 dpi and print twice Printer will print 180 dpi precision four times at feeding direction 720 1080 Printing precision is 360 dpi and print twice Printer will print 180 dpi precision six times at feeding direction 720 1440 Printing precision is 360 dpi and print twice Printer will print 180 dpi precision eight times at feeding direction 10 2 3 Printer Parameter Setting Pressing Printing parameter setting it shows warning as below Ga FINA320B User s Manual
14. 0V Chart 9 1 System diagram 9 3 Functions 1 To keep the front heating board in auto constant temperature With advanced protective functions to avoid over heating leakage etc The line will be cut off automatically if a certain line s temperature is over 70 C As soon as the temperature lowers it will resume heating Over heating will not occur when the entire input signal is cut off 3 The system can work independently and can be easily transplanted It should be optional to select the input voltage from AC110V to 220V 4 The heating system is controlled by advanced intelligent microprocessor it has features of heating up quickly controlling temperature accurately and saving energy 5 Inner heaters are used It is easy to install with no extra space needed and longer lifetime 48 FINA320B User s Manual 9 4 Working Process and Characteristics 1 Users can amend the temperature of front heater from LCD 2 Heating power supply is independent from control power supply Please turn on the heating power before turning on the power for the printer Once the power is on the system heats up automatically to set temperature and keeps the temperature at the set value Without turning on power for printer the heating system will not work However there is still AC 220V inside machine 3 Temperature detector lies on the right sixth pressure roller Print media should cover this region when printing 4 After p
15. 1 a FINA320B User s Manual 5 Select ink curves and ink curves shows relations between voltage and Application i temperature 9 Ink Curve 0019 Offline Xr 3s EP LCD displays details as below O 0 0 0000 1234 The name of ink curve indicates as below 1 SK Stands for SKIEO print head Xr Stands for Xaar print head Sp Stands for Spectra print head 25 Stands for 200 dpi print head Stands for 300 dpi print head Stands for solvent based ink type O Stands for oil based ink type U Stands for UV ink type 4 ink name The ink curves are different with different ink types For using Xaar130 print head and solvent ink in this printer so the ink curve showing on the LCD lists as upper PH Heater The LCD display details as below Menu PH Temp Offline 0025 Used for setting temperature bedplate XXXX flashes on the LCD Press or Y key to increase or reduce the value of temperature And the bigger value is the higher temperature is 32 FINA320B User s Manual Front The LCD display details as below Heater Menu FH Temp Offline 0025 Used for setting temperature of front and rear bedplate XXXX flashes on the LCD Press ft or Y key to increase or reduce the value of temperature And the bigger value is the higher temperature is The LCD display details as below Menu FH Temp er Offline 0025 Used for setting temperature of middle bedplate XXX
16. FINA and the model as 320B 3 Click the Printer setup Set the relevant value in the following dialogue box Print Setup Print Heads 16 x Wave Form Line M Color C M ColorM M ColorY WM ColorK Print Mode Test Mode Media Mediao y Ok Cancel Note Details of the functions above and others referred to the FINA RIP Manual 37 FINA320B User s Manual 11 Click Printing Project to print 12 LCD displays as below when printing PRINT PROJECT LINE TOTAL XXXX FINSH XXXX RIP READY XXXX RIP ready lines 13 If clogging appears during the printing press ONLINE for a longer time 3s to pause printing for print head cleaning After cleaning press ONLINE to go on printing Cleaning procedure during printing If you find print heads clogged during printing press and keep ONLINE button to pause printing Select Auto clean in menu and press ENTER key the system presses ink 2 seconds and stops 1 second automatically Then cycles once The pressing ink time in the whole process is 4 seconds Scrub the head surface with a clean stick after ink not dropping from print holes After accomplishing cleaning 5 or 10 minutes later Press ENTER key to continue printing Press ESC key to cancel the printing Do not switch mode from ONLINE to OFFLINE until printing cancel shows up on computer 14 Press ONLINE when the printing is all finished Then the printer is under the Offli
17. Pipeline 26 27 28 Chart 4 7 Print Interface 17 FINA320B User s Manual Parts on the printer include 1 Control Panel Set up and execute function and mode 2 Infrared Drier Overseas option fittings expedite the print media drying 3 Media take up sensor control the media take up motor run or stop 4 Media take up motor Take up Roller driver 5 Media feeding motor Feeding Roller driver 6 Media auto manually feeding switch switch auto to manually or reverse 7 Media auto manually take up switch switch auto to manually or reverse 8 Direction switch Control the CW CCW direction for media feeding 9 Print Head localizer fix the Print Head 10 Y raster strip Take count of print head horizontal moving so as to insure of Y direction image precision 11 Y drive strap Drive print carriage horizontal moving 12 Pinch Roller Press media and make media smoothly 13 Printing Platform Platform for printing 14 Press Roller Control Pole Control press roller up down for media feeding 15 Flash Plate handle Control the flash plate up or down position 16 Clean roller Clean the print head for auto clean 18 FINA320B User s Manual 17 Capping assy Keep the print head wet when not use the printer 18 Capping handle Control capping assy up down for keep the print head wet 19 Power Switch Turn on off printer 20 Manually Valve Control
18. X flashes on the LCD Press or Y key to increase or reduce the value of temperature And the bigger value is the higher temperature is FINA320B no this function le FINA320B User s Manual Media Press ENTER to execute the operation the LCD displays OFF means the Detect function is switch off when the printer is waiting OFF function switch off Press or Y key to switch on the function ON function switch on Pull up the press pole and then pull it down the LCD displays details as below Media Detect Star 0000mm Lenth 0000mm Press ENTER key to start media edge detecting Press ESC to cancel the operation After detecting OK displays means the detecting is successful and saves the result as print position which should add the value of offset set at below step Error displays means the detecting is failed and the value of print position does not change This function is optional Margin XXXX flashes on the LCD Press f or Y key to increase or reduce the value This value added to the value of media detecting is saved as the value of print position This function is optional Fan XXXX flashes on the LCD Press f or Y key to increase or reduce the value of Volocity Fan Volocity And the bigger value is the higher Fan Volocity is Clean Post Set the distance from original position to cleaning position P H moves to cleaning position and waiting cap the P H It s better not to change this
19. ck the sponge on the wet keeping frame clean or replace it if necessary 4 Clean feeding and take up rollers with PM acetate Skid on the rubber roller will cause error code from service and impact print quality 4 Do normal clean for the printer everyday O Weekly work 4 Clean the dust on the surface of fans on dry board Assemble them after ensure clearness of the leafages 4 Check pump route if there is any loose OMonthly work Clean the filters ofC M Y and K Check the tension of straps Clean dust in the power tank Oyearly work Replace ink filters 66 FINA320B User s Manual Blower the dust on power tank with compress air Clean the ink supply routes Clean the liguid pumps for ink supply Oil the gears of feeding and take up motors Check whole circuit if there is any loosen or broken Repair it in time if necessary Check if there is any tear on the tube and wire in the towline set and replace it if necessary 11 2 Maintenance of print head Always keep the surface of print head wet with flush solution If the printer is left unused the print head must be dropped with flush solution and covered with fresh keeping polyethylene films to keep it wet 1 Moisturizing of print head If the printer is left unused for 2 day and above do as below to keep the print head wet tire Dip the unwoven fabric with flush solution Di Cover the unwoven fabric on the surface of print hea
20. d 3 Wrap the print head unit with fresh keeping polyethylene film 4 Cover the wet keeping frame the print head 2 Unload print head Do as follows when you are going to unload print head 1 Pump out ink from print head and clean it with flush solution Des Power off the printer and plug out power line from socket 3 5 Check static on the machine with a multimeter and release the static if necessary 4 Loosen the Up Left and Right screws and take out the right screw SA Take out the print head and put it on an unwoven fabric soaked with flush solution 3 Assemble print head 1 Power off the printer and plug out power line from socket 2 Check static on the machine with a multimeter and release the static if necessary 3 Loosen Up and Left bolts take out Right bolt and fix the print head to the frame Put on Right bolt and tighten Up Left and Right bolts properly 4 Connect the data cable to print head connect board one by one 5 Check the connection of data cables to eliminate wrong connection Caution If the data cable is wrong connected the print head will damage when power on 11 3 Maintenance for ink supply system The ink supply system is a very important Maintenance for ink supply system is also very important The ink supply system includes main ink tank system and assistant ink tank system with filters to separate the ink from the open air So cleanness of environment is primary condition to place the pri
21. d need cleanness with flush solution timely when they are smeared by ink Warning Ink supply integration box should clean by authorized personnel only Improper operation will result in ink supply system troubles 11 4 Maintenance for other parts 1 Lubrication for print head rail As normal regulation user should add lubricating oil to print head rail daily and never use compound oils 1 Add a few lubricating oil on a cotton fabric and move the print head to original position Brush the print head rail with the cotton fabric to create an average oil layer on the rail 2 Power the printer and move the print head unit left and right repeatedly dos Erase the oil smear on the both ends of the rail Erase the oil drops on the rail again before printer running o 2 Feeding and take up rollers Oil the gears of media feeding and take up rollers monthly to avoid rust 68 FINA320B User s Manual err24 err23 err22 err21 Wrn20 Wrn19 err16 err15 err14 err13 err12 errll err10 err9 err8 err7 err6 err5 err4 CHAPTER 12 ERROR MESSAGE user not match aux ink supply board error rtc ink supply board error time out will time out Heating not complete Original Position Sensor not connect cfgrom err aux ink supply board ver err FPGA main board ver err se anti counter is not correct se error between command and action is large Y raster not connect Y raster direction of conter is different fr
22. ead adjustment with TRY Software adjustment have 4 steps Two print heads one color adjustment four color overlap horizontal and vertical BID overlap Feeding compensation adjustment It should be used SmallGrid126 group file to adjust these parameter under the TEST Mode Below is the detail steps 1 Select Open File load the file C try SmallGrid126 group Chart 10 8 SmallGrid126 group 2 Adjust the 4 color overlap Open TRY and go into the print setup dialog Select the corresponding quantity of print head eight or twelve or sixteen and corresponding color Cyan is the benchmark color The four color overlap is beginning with cyan Print Setup Print Heads 16 Wave Form Line M Color C FT Cc lor M Color Y F Color K Print Mode Test Mode T BiDirection Media Median More Ok Cancel 56 FINA320B User s Manual 10 3 1 Vertical adjustment for two PH with one color Select cyan line mode in the print setup dialog print below picture SmallGrid126 group wae NNNNNNNNNN IIS RSS I SS line Third PH fourth PH and second PH are in the same line So you should adjust the vertical compensation for the first PH minus number the first PH printing line will move left directi
23. is no other operations in this process 8 4 2 auto clean heavy One cycle of auto heavy clean process have below steps Air pump work waiting 55 seconds cleaning roller go up Print carriage go left gt Waiting and Print carriage Cleaning roller End 4 flush go right go down The total time of the auto clean process spend 85 seconds The LCD will display BUSY and there is no other operations in this process 8 5 Operation Description of manually capping system 46 FINA320B User s Manual Capping shelves went onto print state when turn the capping handle on the right estate A Capping state Capping handle Caution The Capping shelves onto print state when you put the Capping handle inside Please put the capping handle on the print state before you turn on the printer or else the printer can not finish self diagnoses Please move the print carriage to clean position and put the capping handle on the capping state before you turn off the printer or else the print head will be clogged 4T FINA320B User s Manual CHAPTER 9 HEATING SYSTEM 9 1 Summary This heating system include Pre heater middle plate heater P H heater and it can adjust temperature based on different media material and temperature It can adjust the temperature automatically to keep temperature constant Customer can have satisfactory printing effect 9 2 Working Diagram ssistant board d operation plate or 22
24. ke sure the printer is well grounded e Itis better to use UPS stable voltage power 4 Requirement for computer In order to avoid problems caused by computer please choose high quality computer or brand computer such as DELL or IBM etc 3 3 Port of Printer USB 2 0 Installation Connect printer s USB and computer s USB directly Find driver for USB at USB Instal File Try Setup under printer s driver 3 4 Connect With Power 1 After all the parts installed move printer to its working area and clean up the package 2 Connect power cables including power for printer and heater printing data cable Protective switch only works for heater s power Usually this switch should be at status of On switch on above far from red point 3 After finishing turn on power The Auto ink supply system runs to pump ink from main ink tanks to Sub ink tanks 4 Feed in media and printer enters waiting status 5 Then go in test printing Observe ink drop If not good clean print head again L2 FINA320B User s Manual CHAPTER 4 EQUIPMENT STRUCTURE AND ACCESSORIES The main components charts of FINA320B Printer list as below Chart 4 1 Control interface and Infrared Drier 13 FINA320B User s Manual 14 FINA320B User s Manual 13 16 T5 e FINA320B User s Manual 18 16 19 17 20 21 FINA320B User s Manual 23 24 Chart 4 6 Pumps and
25. llation Place e Put printer at a horizontal and stable place with enough space otherwise the Printer may not work properly e Don t leave Printer at a place where temperature and humidity change severely Avoid direct sunlight strong light or heat FINA320B User s Manual e Avoid shaking or vibrating e Keep sufficient room around printer for air circulation e Place printer nearby the wall socket so that it is easy to connect or disconnect the power supply 1 5Warning Caution and Attention Warning Must obey in order to ensure personal safety e Caution Must obey in order to protect the machine e Attention Contain some important and useful information about operation FINA320B User s Manual CHAPTER 2 TECHNICAL PARAMETERS 4500mm 925mm f C 1200m BEL ad Chart 2 1 Printer Outlook and dimension FINA320B User s Manual Product Mode FINA320B Xaar 130 600 DPI 8 12 16 Speed and output Print Mode Media Transmission Auto Media Feeding amp Take up system Take up is OPTIONAL 50kg Roll PVC Flex Vinyl window film polyester ei Max Printing Width 3250 mm Display LCD display with 8 key panel self diagnosis available Ink Type Eco solvent and Solvent base ink main ink tank volume Main features Auto Media heating Pre heater middle plate heater P H heater Infrared Drier OPTIONAL
26. n keys 1 Operation via control panel key Scroll the menus for selection reduce or increase the values on LCD gt key Move the cursor position over the number string on LCD 2 When the printer is waiting I key Move the media forward and backward lt key Move the p h carriage to cleaning position for cleaning and move it back to original position after cleaning 24 FINA320B User s Manual 2 Function keys 1 ONLINE Switch the printer online and offline press down and hold it for several seconds to pause printing Waiting Online 2 ES eturn to up level menu 3 ENTER Confirm and execute the operation 4 FUNC Shift to special function Combine with key to test print when the printer is waiting 3 Basic operation After power on the printer the system executes X and Y motion test and p h test Booting gt System gt Y Motor V1 20 gt X Motor Check gt Print head After self test the system moves the p h carriage back to original position The LCD displays printer model and version number and then shift to basic operation menu shown as below That stands for the printer is ready 1 Ink Status 2 Heat Status 3 Cleaning Tool Offline 4 Print para 220 2 FINA320B User s Manual 6 1 2 Menu structure Menu structure includes main menus and sub menus Main menus followed by s have sub menus inside Submenus follo
27. nance as 100 50 and 10 Print the color blocks under test mode and check the print result If the print result is normal which means no ink break and no ink spots on the mediums the printer can work normally B FINA320B User s Manual Chart 5 2 color blocks for test printing 5 2 Maintenance of Print head 1 Ink replacing Flush the print head with the original ink first and then flush it again with new flush solution which matches the new ink 2 Print head cleaning If low guality printing takes place a positive pressure cleaning is proper for the head After positive pressure cleaning scrub the head surface with a dry clean stick to stop ink streaming from the nozzles Be sure not to use a stick with flush solution to scrub the head surface otherwise the flush solution will be siphoned into the nozzles 3 Moisturize print head Use wet keeping frame to moisturize the head if the printers is left unused The print head moisturizing method of this printer displays as follows adhere a clean non woven fabric with some flush solution on the print head and wrap it with a fresh keeping polyester film o FINA320B User s Manual CHAPTER 6 BASIC PANEL OPERATION 6 1 Menu Structure of Control Panel ONLINE ESC ENTER FUNC gt 3 3 Se gt SS 1 LCD 2 Function Keys 3 Direction Keys Chart 6 1 Control Panel 6 1 1 Function description of the keys 1 Directio
28. ne mode Note To cancel printing operation usually do in RIP If you want to cancel printing directly on the printer press ONLINE button after the menu printing cancel appears in software 38 FINA320B User s Manual CHAPTER 7 INK SUPPLY SYSTEM 7 1 Summary This ink supply system can control automatically several pumps at the same time and provides protect function Isolated ink supply system is easy for operation 7 2 System Diagram Sub tank Ink tube Print Head Floating switch Filter l 5 Output a Input o Buzzer Signal for Pump light floating switch Pump Ink light Interface signal a Main Tank Power Chart 7 1 Ink supply and cleaning system Diagram 7 3 Structure The ink supply and cleaning system consist of ink tanks ink pumps print filters sub tanks print head control board and etc The components charts displays as below 39 FINA320B User s Manual Ink cartridge C 2 Ink cartridge M 3 Ink cartridge Y 4 Ink cartridge K Chart 7 3 1 Ink tanks 40 FINA320B User s Manual 1 Ink pump C 2 Ink pump M 3 Ink pump Y 4 Ink pump K 5 Air pump Chart 7 3 2 Ink pumps 1 Ink filter C 2 Ink filter M 3 Ink filter Y 4 Ink filter K Chart 7 3 3 Ink filters 41 FINA320B User s Manual 1 Assistant ink bottle C 2 Assistant ink bottle M 3
29. nk supply is easy to break If the lt FINA320B User s Manual voltage is too low the printing line is not straight and easy to have an angle Besides ink volume is small and output color is light Therefore every head has its optimal EF value When adjusting you can adjust the EF value one by one Usually user needn t to adjust EF value Note When install print head select the 2 with same or similar EF value for 1 color or it will cause different color of front and rear print heads 6 3 Printing Steps On normal condition the steps are as follows 1 Power on the printer 2 Turn on the computer Note It is recommended to turn on the printer before computer Otherwise the connection may fail 3 Install media put down the press bar Clean the head and start the self diagnosis till no nozzle clogging 4 Press ONLINE 1 Ink Status 2 Heat Status ONLINE 3 Cleaning Tool MODE OFFLINE 4 Print para Offline mode Online mode Chart 6 2 Online and offline Mode 5 Trim the pattern for printing and save it in computer 6 Open RIP 7 Create new file 8 Read the pattern for printing 9 Adjust the position size property and resolution of the pattern 10 Printer setting 1 Select File Printer setup Dialogue box shows as below 36 FINA320B User s Manual m H3Temp H Temp Ready 250 PM y Chart 6 3 Printer Setup dialog box 2 Select the type of printer as
30. nter 1 Main ink tank system Main ink tank system consists of main ink tanks filters liquid pumps and waste ink tanks 67 FINA320B User s Manual Maintenance includes 1 Clean the main ink tanks especially air filters monthly 2 Clean or replace filters of ink and flush solution per half year 3 Clean around the main ink tank system weekly 2 Assistant ink tank system Assistant ink tank system consists of assistant ink tanks safety tanks and trilateral valves Ink drops get together on the floaters in assistant ink tanks and dry to shape small balls on the top of sensors which will impact the sensitivity of sensors To clean the floater do as follows 1 Pump out ink from ink tubes by operating on clean control panel 2 4 Unload the 4 assistant ink tanks from the back of print head unit Bx Loosen and take out bolts from the cover boards of assistant ink tanks and then take the cover boards and floaters 4 Clean the floaters and assistant ink tanks with unwoven fabric and sponge soaked with flush solution Ensure the floater switch move smoothly and then dry floaters and assistant ink tanks ST Reload floaters in assistant ink tanks and assemble assistant ink tanks on the back of print head unit The safety tank also needs cleanness timely The method is same as assistant ink tank except for the 2 air filters in addition The trilateral valves in the ink supply system are also very important an
31. om motor Motor Board Error ErSt_InkAOverflow ErSt_InkSOverflow ErSt_InkTimeOut ErSt_InkPressure 69
32. on and plus number the first PH printing line will move right direction For this picture you should put plus number 4 in the Para setting dialog number 4 is just a sample you should set repetitious then get the correct number Horizontal Compensation fp n mn m be fo jn j lt l l gt TI NNNNNNNNNNN ON N N N N N N N N N NNN NNN N NNN N NIN NI NI NIN NINI NI NI N NNN N N NN INI N N N NA N N NIN N FINA320B User s Manual Print Heads 16 Wave Form Line Y Color C Print Mode Test Mode l BiDirection Media Median y More Ok Cancel 2 Printing SmallGrid126 group file NN NNNNNNNRNNRN N N N N NN N N NN N NN S Heron fis NNNNNNNNNNNN NN NNNNNNNNNN NNNNNNNNNNNNN NNNNNSSNNNSIN Verti al line The horizontal line and the vertical line of the two color is not in the same line So you should adjust the horizontal compensate and the vertical compensate parameter for this two color and let the two color in the same line 59 FINA320B User s Manual From this picture you can see the magenta horizontal line is a little bit upper than cyan So you should adjust the horizontal compensate for magenta PH Plus number magenta line will go down Minus number magenta line will go up For this picture you should put plus number 2 in the Para setting dialog number 2 is just a sample you sh
33. onvenient operation b Don t touch the surface of head and socket with hand c Clean the filter with flush solution d Connect a tube on the exit of the head to prevent ink flowing into the socket 21 FINA320B User s Manual e Don t touch the surface of head with other objects f Be careful to distinguish In tube and Out tube of the head g Eject flush solution from the nozzles with strength no more than 0 3 kg It is better to hold the injector with single hand and push it with the same thumb 2 Extrude air from the print head After fixing the head on the head frame be cautious of the in tube and out tube Remove the Cap from the Out tube positive pressure clean to fill the head with ink till ink streams out from nozzles During the process air is extruded completely from the head 3 Moisturize print head surface After extruding air from the head cover the Cap on the Out tube Positive pressure clean again until ink streams out of the nozzles then scrub the head surface with a dry clean stick to form a protecting layer of ink on the head surface The ink on the surface will stream into the nozzles because of negative pressure Notes Never scrub the head surface when head surface is dry for that will orient air into the nozzles and shape bubbles in the pipelines and affect the printing guality 4 Test printing Design some color blocks as 20x20cm with some image operating software and set color lumi
34. ould set repetitious then get the correct number Vertical Compensation K X M E o 0 CM o After set the parameter Print again then get the below picture N NN N N NIN NININ lt 4 Horizontal line VAVAVAVAVA VAVAVAVAVA TM AL A V ML A AA VAVAVAVAVA LAVA VAVAVAVAVA VAVAVAVAVAVA VA 27 A A A7 2 VAVAVAVAVAVA AAA AAA PAL AA YA A AA _ SAN yA PS Z y A A EA f JAAA F N N VA JE MWO W Y E A m ME MW AM A VAVAVAVAVAVA Wa E V JE M J Vo A N N N N N N NIN EA NNNNINININ W N Vertical line N It is ok for horizontal line then you should adjust the vertical line for the two color print heads From this picture you can see the magenta vertical line is a little bit right than cyan So you should adjust the vertical compensate for magenta PH Plus number magenta line will go right Minus number magenta line will go left For this picture you should put minus number 4 in the Para setting dialog number 4 is just a sample you should set repetitious then get the correct number 60 ZT VA TT y TM ZZA PATAS AA E ADA VA VA EEE bi 1447740 1 AZ AA aa aa ae VAVAVAVAVAVA VAVAVAVAVAVA VAVAVAVAVAVA VAVAVAVAVAVA VAVAVAVAVAVA VAVAVAVAVAVA LONAS VAVAVAVAVAVA VAVAVAVAVAVA VAVAVAVAVAVA LIT FINA320B User s Manual 62 ob B SSs 1515 g
35. rinting make sure to turn off the two powers 49 FINA320B User s Manual CHAPTER 10 SOFTWARE OPERATION 10 1 Installation of APRINT Software 10 1 1 Installation of RIP a Insert RIP CD into computer s CD ROM b Run APRINT RIP exe c Follow the instruction to finish the installation 10 1 2 Installation of printer driver Ja Insert installation CD into CD ROM b Run setup exe under directory of Try Setup Aprint V5 13 c Follow the instruction to finish the installation Note Please use the default directory for the installation 10 2 Application Of Printer Driver Note The driver program is only for engineer to adjust the print head for normal operation 10 2 1 Enter TRY 1 Click Start Program Try enter Try system 2 Open TRY and not necessary 50 x FINA320B User s Manual CHART 10 1 TRY main window 3 First choose the type of printer Click Printer menu choose the item of FINA320B T LEE TUN NINE HE M RIH i BM BE E BE A E E Chart 10 2 Machine type list 4 Then open File to adjust some settings E E FINA320B User s Manual BID test group Hinter group EZ LINE group nallGrid126 group overlap 360 group SmallGrid group overlap 600 group VMOverlap group overlap 1080 group VSOverlap group l SmallGrid126 group Chart 10 3 File menu 10 2 2Print Setting Print Setup 02 FINA320B User s Manual Chart 1
36. rom the latent source of electromagnetic disturbance For example loudspeaker or wireless phone If you use additional cable please make sure that total amperage of the equipment connecting with cable shall not exceed the amperage of the power supply Moreover the amperage of all equipment connecting with wall socket does not exceed the amperage of the wall socket Do not use damaged Electrical Power wire e Do not repair Printer by yourself e Shut off the power and ask experienced technician for help if the following situations occur Power cable or plug is damaged Liquid splashes into printer Printer falls down or broken Printer cannot work properly or change in property 1 2 Caution When Using Printer e Don t use your hand to move print head otherwise the printer will be damaged e Always use power switch to turn On off the printer Before shutting down the Printer do not pull out Power Supply wire or Data Wire e Before moving the printer please make sure the print head is fixed at original position 1 3 Guide When Using Ink Cartridge e Keep ink away from children Do not let the children drink or touch e Ifink spills on the skin please wash with soap and water If ink splashes into eye please wash with water immediately e Do not shake the ink cartridge in case ink leak is caused Please keep surrounding clean when you replace a new ink container It helps you improve printing quality 1 4 Choosing Printer Insta
37. to assistant ink tanks if it found ink not enough Warning 3 displays on the LCD 2 When ink channel lacks of ink system will start the pump automatically and indicator lighten After the floating switch senses the ink the pump will continue to work for a little period and then stop and the indicator light extinguishes 3 When ink in assistant tanks is used out or other reasons cause some pump running overtime the system will alarm voice a straight buzz and Err5 displays on the LCD Press ENTER key on control panel to refill ink and cancel alarming 4 When safety tank is full system will alarm as short buzz and Err6 displays on the LCD Then you should empty the safety bottle 7 6 Intelligent Detection Function Intelligent detection function for ink supply system is implemented by collecting floating switch signal with high frequency By using concept of probability the signal is regarded as effective if probability of floating switch signals is higher than a set value for example 80 Therefore wrong act of floating switch can affect the system s stability much less and accordingly system s anti disturbance improves 44 FINA320B User s Manual CHAPTER 8 CLEAN AND CAPPING SYSTEM 8 1 Summary This printer adopts automatically positive pressure cleaning and manually capping system You may execute cleaning before printing during printing or idle for a long time 8 2 System Diagram
38. wed by s have no lower level inside Main menu includes items as below gt 1 Ink Status 2 Heat Status 3 Cleaning Tool 4 Print para R 5 Application 6 Engineer Set Press T Y key to scroll the menus upward and downward Press ENTER to unwrap submenus For example while the arrow points to 1 Ink Status press ENTER to unwrap the submenu LCD displays details of submenu M1 as below Ink Status M1 ChACMYKcm Offline On the LCD M1 stands for this submenu under main menu No 1 Here press ESC key it returns the display to main menu Arrow points to the first line on the LCD Scroll the submenus by pressing ff and key same as main menu The submenu followed by a means has no lower submenu inside Press ENTER key to execute the operation Here press ESC key operation will be canceled 26 FINA320B User s Manual 6 2 Function Description in Details 1 Ink Ink status displays Status Ink The LCD display details as below Status ChAC Menu Ink Status MYK ChACMYK Rn __ Offline Al Item Ch stands for ink channels A means all channels Item Rn displays ink supply status of corresponding channel Item AL displays ink lack alarming of corresponding channel Press ENTER to refill ink and cancel alarming For 4 colors and 8 print heads supplying ink and no safety tank in this printer one of C M Y K on the LCD flashes in low ink status and A
Download Pdf Manuals
Related Search