Venmar 30635615 Power Brush User Guide (30042511A).indd
Contents
1. RECEPTACLE Lock Button e Lock Button Hose HANDLE RELEASE BUTTON Wand A00021 See Section 5 on page 7 for wand and hose compatibility table ADo 28 ma 2 HOW TO USE POWER BRUSH WAND CAUTION Always pick up hard or sharp objects by hand before using your power brush Items such as pins hairpins tacks crayons etc may damage the brush roll or may break the belt 2 1 WAND RELEASE The power brush is not recommended for use on bare floors Wand release pedal A on power brush allows you to quickly disconnect wand and switch to combination floor rug tool for use on bare floors 2 2 POWER BRUSH NECK RELEASE CAUTION Always unlock brush neck before use Push down power brush neck release pedal B to unlock brush neck Return the neck to the upright position for storage 00020 2 3 POWER BRUSH HEIGHT ADJUSTMENT The icons D refer to the carpet pile height Select height by depressing height adjustment pedal C to desired position Extra Low Low uu Medium or LLU High HEIGHT ADJUSTMENT LED INDICATORS The LEDs show the carpet pile covered by the selected height e g when LLLI High is selected all LEDs will be lit since this height covers all pile heights So if Extra Low is selected only the lowest LED will be lit Apooe8 2 4 WAND LENGTH ADJUSTMENT Extend E or shorten F the wand to comfortable2. Disengagebrushrollfromworn beltandextract the belt from motor shaft by a twisting motion in the enlarge area I specifically made for Ss that purpose Fic 4 Install new belt by reversing steps 8 to Q a J T L e glas L NOTE Toeasebeltreplacement startbyinserting o PL a po F mA F lt r one end around the motor shaft in the enlarged area I Insert brush roll through belt until belt is seated in its place Push down brush roll back in place SS 4 2 HOW TO CHANGE BRUSH ROLL Replace brush roll when brush roll brissles are worn to the base support bars level 8 Turn power brush over and using a Phillips no 2 screwdriver remove the 3 brush roll cover retaining screws Fic 1 and set aside 8 Remove brush roll cover Fic 2 Tofree brush roll from base start by sliding the belt side end and pull brush roll sideways 1 Oncedisengagedfromhousing liftbrushroll 2 out of its compartment Fic 3 Disengage brush roll from belt Discard worn brush roll 6 Insert new brush roll through belt until belt is seated in its place Push down brush roll back in place Finalise the installation by reversing steps 8 to 8 5 WAND AND HOSE COMPATIBILITY ADOO37 ADOO38 NOTE If your dual voltage hose is not compatible with your new 30635615 power brush please contact Venmar cus
3. CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE This warranty supersedes all prior warranties Warranty service is to be completed by an authorized Service Center designated by Venmar Ventilation ULC Where applicable in home service will be made available only in areas where a contracted service provider offers service If in home service is not available the product will be repaired or replaced at Venmar Ventilation s discretion by the nearest authorized service provider The unitremovaland reinstallation works are underthe customer responsibility and Venmar Ventilation ULC cannot be charged for them To qualify for warranty service you must a notify Venmar Ventilation ULC at the address or telephone number stated below b give the model number and part identification and c describe the nature of any defect in the product or part At the time of requesting warranty service you must present evidence of the original purchase date IF YOU NEED ASSISTANCE OR SERVICE For the location of your nearest Venmar Ventilation ULC authorized Service Center Dial Toll Free 1 844 670 2334 Please be prepared to provide Product model number e Date and proof of purchase The nature of the difficulty Venmar Ventilation ULC 550 Lemire Blvd Drummondville Qu bec J2C 7W9 www venmar ca Released March 2015 Product specifications subject to change without notice 8
4. work position by holding the wand grip G in one hand and sliding the upper section the one with the prongs with the other hand AD0023 2 5 EDGE CLEANER Brush extends full width for effective edge cleaning along both sides of nozzle To operate simply run cleaner along edge board Rubber bumper protects furniture and baseboards 4 2 HOW TO USE POWER BRUSH WAND cont p 2 6 ELECTRONIC CIRCUIT BREAKER The power brush is equipped with an electronic circuit breaker that protects the motor and the belt if a too large object is picked up accidentally If the power brush stops while vacuuming turn the power unit off using handle Release the power brush from the wand and turn it over to see if there is an obstruction When brush roll jam has been cleared press the reset button H and connect the power brush back to the wand Finally turn the power unit power brush back on If it fails to restart or continues to trip without any apparent reason the power brush must be serviced by an authorized service center ADOO30 3 CLEANING AND STORAGE A WARNING Disconnect electrical supply before servicing or cleaning the unit Failure to do so can result in electrical shock or personal injury from cleaner suddenly starting 3 1 CLEANING BRUSH ROLL In order to keep high cleaning efficiency and to prevent damage to your vacuum cleaner the brush roll must be cleaned every time the belt is
5. Z Ve rimRa ee DELUXE ELECTRIC POWER BRUSH MODEL 30635615 A FOR HOUSEHOLD USE ONLY A AB0008 HOMEOWNERS OPERATING INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Venmar Ventilation ULC Drummondville Qu bec 1 844 670 2334 Register your product online at www venmar ca 30042511A The instructions given in this booklet serve as a guide to routine maintenance To obtain the most satisfying years of service read through these instructions and keep them handy for future reference IMPORTANT SAFETY INSTRUCTIONS When using an electric appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THE POWER BRUSH WARNING A To reduce the risk of fire electric shock or injury 1 Always turn power off and unplug before cleaning or servicing the power brush 2 Do not pick up the following items Sharp objects flammable liquids hot ashes burning matches cigarettes etc 3 Never use connect or disconnect the power brush with wet hands 4 Do not use with damaged power plug or plug pins If the power brush is not working properly contact your local supplier or service agent The problem may be covered under the warranty 5 Do not put objects into the brush opening 6 Do not use with brush opening or air channel blocked Keep free of dust hair etc 7 Keep hair loose clothing fingers and all parts of body away from openings and moving parts 8 Never l
6. changed The brush roll must also be cleaned according to the following schedule VACCUM CLEANER USE CLEAN BRUSH ROLL Heavy used daily Every week Moderate 2 3 times per week Every month Light once a week Every 2 months Check and remove hair string and lint build up frequently in the brush roll and end cap areas Remove any dirt or debris in the belt path and in the brush roll areas 3 2 CLEANING HOUSING To keep the power brush housing clean it can be wiped with a damp cloth and a mild soap solution then thoroughly dried Never use any type of chemical as they can damage the housing 3 3 STORAGE Ensure that hose and power cord are disconnected from wall inlet before unplugging power brush 8 Disconnect hose handle from wand 6 Always keep hose neatly coiled when not in use When not in use the power brush should be stored in a clean dry place 4 MAINTAINING THE POWER BRUSH A WARNING Disconnect electrical supply before servicing or cleaning the unit Failure to do so can result in electrical shock or personal injury from cleaner suddenly starting 4 1 HOW TO CHANGE BELT 8 TurnpowerbrushoverandusingaPhillipsno 2 screwdriver remove the 3 brush roll cover retaining screws Fic 1 and set aside 8 Remove brush roll cover Fic 2 Tofree brush roll from base start by sliding the belt side end and pull brush roll sideways 1 Oncedisengagedfromhousing liftbrushroll 2 out of its compartment Fic 3
7. eave electric power brush unattended while it is plugged in 9 This is not a toy Do not let children play with power brush Children should be supervised when near the power brush 10 Use only manufacturer s recommended attachments 11 Do not use outdoors or on wet surfaces 12 Do not use to pick up water 13 Use extra care when cleaning stairs 14 Always check underside of product for any obstructions prior to use 15 Do not use without dust bag with 500VF model or permanent filter with 600 VF and 650VF models in place in power unit 16 Motor shaft can become hot during normal use To prevent burns avoid touching the motor shaft when servicing the drive belt 17 Keep your work area well lighted 18 When servicing or cleaning the unit it is recommended to wear safety glasses and gloves 19 Store your cleaner indoor in a clean dry area 1 HOW TO ASSEMBLE POWER BRUSH WAND HANDLE 8 Read important safety instructions before installing power brush 8 Ensure hose is disconnected from power supply before installing power brush 6 Push wand into power brush neck so that the Hose HANDLE lock button snaps in place Connect hose handle into wand quick connector and ensure that the prongs are aligned with the receptacle holes Push until lock button snaps in place RECEPTACLE Wann To Power BRUSH CONNECTION Quick CONNECTOR RELEASE a Power BRUSH NECK RELEASE WanD Grip Hose HANDLE
8. rvice NOTE The motor is permanently lubricated and sealed Do not oil the motor at any time 8 WARRANTY VENMAR VENTILATION ULC ONE YEAR LIMITED WARRANTY Venmar Ventilation ULC warrants to the original consumer purchaser of its products that such products will be free from defects in materials and workmanship for a period of one 1 year from the date of original purchase THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE During this one year period Venmar Ventilation ULC will at its option repair or replace without charge any product or part which is found to be defective under normal use and service THIS WARRANTY DOES NOT APPLY TO CONSUMABLES SUCH AS BELT OR BRUSH ROLL This warranty does not cover a normal maintenance and service or b any products or parts which have been subject to misuse negligence accident improper maintenance or repair other than by Venmar Ventilation ULC or an authorized representative faulty installation or installation contrary to recommended installation instructions The duration of any implied warranty is limited to the one year period as specified for the express warranty VENMAR VENTILATION S OBLIGATION TO REPAIR OR REPLACE AT VENMAR VENTILATION S OPTION SHALL BE THE PURCHASER S SOLE AND EXCLUSIVE RE MEDY UNDER THIS WARRANTY VENMAR VENTILATION ULC SHALL NOT BE LIABLE FOR INCIDENTAL
9. tomer service at 1 844 670 2334 to receive a free electrical cord part no CRD400 01 that will enable you to connect your new power brush to your hose IMPORTANT Do not return the brush to your retail store 6 SERVICE PARTS AA0002 Order Service Parts by Part No not by Key No REPLACEMENT PARTS AND REPAIRS In order to ensure your unit remains in good working condition you must use Venmar Ventilation ULC genuine replacement parts only Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of safety Any third party replacement part used may cause serious damage and drastically reduce the performance level of your unit which will result in premature failing Venmar Ventilation ULC also recommends to contact a Venmar Ventilation ULC certified service depot for all replacement parts and repairs 7 SERVICE INFORMATION To avoid unnecessary service calls check the belt and brush roll often Replace the belt if it is stretched or cracked Clean the brush roll bristles when they are wrapped with thread and hairs Build up could cause the brush to rotate unevenly The model number and serial number are indicated on the rating label located underneath the power brush Always refer to these numbers when inquiring about se
Download Pdf Manuals
Related Search