USER GUIDE
Contents
1. O Wireless B Stow N Gom D KeyPee Vargus USER GUIDE Table of Contents Introduction 3 System Requirements 3 Installing the Battery 4 Connecting the Receiver and Installing the Default Drivers 5 Turning the Keypad On and Off 5 Establishing a Communications Link 6 Using the Keypad 7 Operating HINS uuu u uu u u yu 8 Power Management 9 Troubleshooting 10 Technical S pporl u u u uu u 12 Product Registration 12 VV TG uu ua um a 12 Regulatory Compliance 12 TARGUS WIRELESS STOW N GO KEYPAD Introduction Congratulations on your purchase of the Targus WirelessStow N Go Keypad The keypad is designed with a built in cavity to store the USB receiver eliminating the potential misplacement of the receiver and to provide ease of traveling with the keypad Package Contents In addition to this user guide this package contains e Wireless keypad e USB receiver e USB extension cable e 1 AA battery e Carrying pouch System Requirements Hardware e PC with an Intel Pentium processor or equivalent e USB 1 1 or 2 0 interface Operating System e Windows 98SE Me 2000 XP e Windows Vista Targus Wireless Stow N2. Go Keypad Installing the Battery Battery Cover Receiver O O Keypad back view 1 Remove the battery cover from the back of the keypad 2 Insert the supplied battery making sure that thepositive and negative ends match the polarity indicators inside the battery housing A NOTE WHEN REPLACING THE BATTERY YOU MAY USE ALKALINE OR OTHER 2 HEAVY DUTY NIMH BATTERY 3 Slide the battery cover back into position until it clicks firmly into place Targus Wireless Stow N Go Keypad Connecting the Receiver and Installing the Default Drivers To connect the receiver 1 Remove the receiver from the back of the keypad 2 Plug the USB receiver into an available USB port on your computer For Windows 98SE follow any on screen instructions to complete the default driver installation For Windows Me 2000 XP Vista the Found NewHardware or Auto detect of a HID device message will appear to indicate the installation of the default driver NOTE YOU MAY NEED TO ESTABLISH A COMMUNICATION LINK BETWEEN THE KEYPAD AND THE RECEIVER SEE ESTABLISHING A COMMUNICATIONS LINK Turning the Keypad On and Off 1 To power on the battery use the on off switch located on the back of the keypad 2 To power off the battery use the on off switch located on the back of the keypad This feature should beused when traveling to prevent power loss 3 To t
3. experienced radio TV technician for help Changes or modifications not authorized by the party responsible for compliance could void the user s authority to operate this product Declaration of Conformity Hereby Targus declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries All trademarks and registered trademarks are the properties of their respective owners All rights reserved Features and specifications subject to change without notice 2006 Targus Group International Inc and Targus Inc Anaheim CA 92806 USA 13 Margus Visit our Website at www targus com Features and specifications subject to change without notice 2006 Targus Group International Inc and Targus Inc AKP01US 410 0006 001B FC N2953
4. anty does not affect your statutory rights Regulatory Compliance This device complies with Part 15 of the FCC Rules Opera tion is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation 12 Targus Wireless Stow N Go Keypad FCC Statement Tested to Comply This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfer ence to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an
5. k off emulates the End key D NumLock on enters 2 on the display J NumLock off moves the cursor down one line of text NumLock on enters 4 on the display NumLock off moves one character to the left of the cursor position NumLock on enters 5 on the display NumLock off No function Targus Wireless Stow N Go Keypad NumLock on enters 6 on the display NumLock off moves one character to the right of the cursor position 7 NumLock on enters 7 on the display Home NumLock off emulates the Home key NumLock on enters 8 on the display NumLock off moves the cursor up one line of text 9 NumLock on enters 9 on the display PgUp NumLock off emulates the Page Up key NumLock on NumLock off NOTE THE NUMLOCK KEY ON YOUR COMPUTER WILL NOT AFFECT THE NUMLOCK 6 gt STATUS OF THE KEYPAD Operating Hints For optimal performance and RF reception e Place the receiver at least 8 inches 20 cm away from all electrical devices such as your monitor speakers or external storage devices e f necessary use the supplied USB extension cable to keep the receiver away from the computer Plug the receiver into the extension cable and the extension cable to the computer HESIN 6 MACAE Targus Wireless Stow N Go Keypad Power Management e To extend the life of your batteries power off the battery with the on off swi
6. n off any wireless devices and their base units that are near the keypad s receiver If you are using the keypad on a metal surface move it and the receiver to a non metal surface Metals such as iron aluminum or copper shield the radio frequency transmission and may slow down the keypad s response time or cause the keypad to fail temporarily Replace the batteries 11 Targus Wireless Stow N Go Keypad Technical Support For technical questions please visit US Internet www targus com support asp Australia Internet www targus com au Email infoaust targus com Telephone 1800 641 645 New Zealand Telephone 0800 633 222 Product Registration Targus recommends that you register your Targus accessory shortly after purchasing it Go to http www targus com registration asp You will need to provide your full name email address phone number and company information if applicable Warranty Targus warrants this product to be free from defects in materi als and workmanship for one year If your Targus accessory is found to be defective within that time we will promptly repair or replace it This warranty does not cover accidental damage wear and tear or consequential or incidental loss Under no conditions is Targus liable for loss of or damage to a devices nor loss of or damage to programs records or data nor any consequential or incidental damages even if Targus has been informed of their possibility This warr
7. tch located on the back of the keypad while traveling or when you re not using it e The keypad s power saving mode feature activates after 4 minutes of non operation To activate the keypad press the NumLock key Targus Wireless Stow N Go M Keypad Troubleshootins What do I do if the keypad does not work Make sure that the polarity of the batteries is correct The positive and negative ends of each battery must match the positive and negative connections in the battery housing Check that the receivers USB connector is firmly attached to the USB port on your computer Verify that the device drivers are installed Make sure you have established a communication link See Establishing a Communications Link When I use the keypad other wireless devices work more slowly or fail temporarily what should I do The keypad may cause interference with any cordless radio based device such as a telephone baby monitor or toy To reduce interference move the keypad s receiver and the base unit of the affected device as far away from each other as possible What do I do if the response time of the keypad is slow or it intermittently stops working Try one or more of the following Increase the distance between the receiver and the rest of your computer equipment 10 Targus Wireless Stow N Go M Keypad Increase the distance between the receiver and the base units of other wireless devices Tur
8. urn on the keypad press the NumLock key located directly above the number seven key 4 The keypad goes into sleep mode after 4 minutes of non operation To wake the keypad press the NumLock key Targus Wireless Stow N Go Keypad Establishing a Communications Link After your computer detects the USB receiver and the default driver software is installed you may need to establish a communications link between the receiver and the keypad before you can use it 1 Plug the receiver into your computer s USB port and turn on the keypad NOTE MAKE SURE THAT YOUR COMPUTER AND KEYPAD ARE TURNED ON ANDYOUR COMPUTER HAS DETECTED THE USB RECEIVER BEFORE YOU ESTABLISHA COMMUNICATIONS LINK Battery Cover On Off Switch VI Reset Button O O The LED on the receiver will flash for 30 seconds to indicate ID search mode Targus Wireless Stow N Go Keypad 2 During this time press and release the reset button onthe back of the keypad When a communications link is established the LED on the receiver will stop flashing You are now ready to use the keypad Using the Keypad Definition of the Keys NumLock on inserts a decimal point NumLock off deletes a number NumLock on enters 0 on the display NumLock off emulates the Insert key NumLock on enters 00 NumLock off inserts a comma NumLock on enters 1 on the display End NumLoc
Download Pdf Manuals
Related Search