065-1195SFP User's Guide
Contents
1. COL Steady Connection has been made in full duplex mode FDX stands for FULL DUPLEX RX Steady Receiving data No reception TX Steady Transmitting data No transmission u 000 Ay 10 SIGNAMAX CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter Installation This chapter gives step by step installation instructions for the Converter Selecting a Site for the Equipment As with any electric device you should place the equipment where it will not be subjected to extreme temperatures humidity or electromagnetic interference Specifically the site you select should meet the following requirements e The ambient temperature should be between 32 113 degrees Fahrenheit 0 to 45 degrees Celsius relative humidity should be less than 95 percent non condensing e Surrounding electrical devices should not exceed the electromagnetic field RFC standards for IEC 801 3 Level 2 3V M field strength e Make sure that the equipment receives adequate ventilation Do not block the ventilation holes of the equipment power outlet should be within 6 feet 1 8 meters of the product Connecting to Power This Converter is a plug and play device Connect the supplied AC to DC power adapter to the receptacle at the back of the converter Attach the plug into a standard AC outlet with voltage range from 100 to 240 VAC Installing in a Chass2. available fiber types and spanning distances to be used in the same converter model The Link Fault Signaling function allows a link failure on either the 1000Base fiber optic connection or the 1000BaseT twisted pair Gigabit Ethernet connection to be propagated to a like device at the opposite end of the fiber optic channel This is useful when managed switches are used in a network so that a dropped link on either twisted pair connection or the fiber optic cable will be shown to the switch at the other end of the circuit for Spanning Tree Rapid Spanning Tree circuit reconfiguration by the connected managed switches It is switch defeatable for use during the initial circuit setup or if managed switches are not used The Gigabit Ethernet Media Converter fully complies with IEEE802 3ab 1000BaseT and IEEE802 3z 1000BaseSX LX Gigabit Ethernet standards In this manual you will find Product overview Features on the media converter Illustrative LED functions Installation instructions Specifications CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter Table of Contents Quick Start Guide ssssvvvvvvvnnvnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnns 2 Physical Description lt s ssssscccssssssssssssnsccessessssesssnseessesssss 2 Functional Description eesossvvvvensnnvvvennnvvsensnnnvesssnnnevsenen 3 FCC Statement BEES Es 4 Trademarks 5 IPRCTACC csissscccacscisscisssoosnssssssseseto
3. 14 F 158 F 10 C 70 C Humidity 5 95 non condensing Emissions FCC part 15 Class A CE Mark Class A Please consult our website at www signamax com for product information and specifications of currently available Signamax SFP modules 12 CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter Contact Information SIGNAMAX CONNECTIVITY SYSTEMS An AESP Company 16295 N W 13h Avenue Miami Florida 33169 U S A Phone 305 944 7710 Fax 305 949 4483 Sales 800 446 2377 Tech Support 800 446 2377 ext 201 Http www signamax com E mail info signamax com
4. SIGNAV AX CONNECTIVITY SYSTEMS Signamax Connectivity Systems Gigabit Ethernet SFP Media Converter Model 065 1195SFP 065 1195SFPI User s Guide SIGNAMAX CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter Quick Start Guide This quick start guide describes how to install and use the Gigabit Ethernet SFP media converter The converter introduced here provides a one channel media conversion solution Physical Description Product Overview D FR TRUSE CONRAN N 000 a S This Gigabit Ethernet SFP media converter is plug and play device Connect the supplied AC to DC power adaptor to the receptacle on the rear panel of the Gigabit Ethernet media converter and then attach the plug into a standard AC outlet with a voltage range from 100 to 240V AC DIP Switch DIP Up Default Setting Down switch Left hand The fiber port auto detects Forces the fiber port to full side full and half duplex duplex mode Right hand Disable LFS Enable LFS LFS side Link fault signaling function The 1000BaseT and 1000BaseSX LX Connectors The 1000BaseT me Connection Te The following lists the pinouts of the 1000BaseT port TP TP TP The 1000BaseSX LX Connection The SFP socket accepts standard Gigabit Ethernet Small Form factor Pluggable SFP modules of various types and spectra SIGNAMAX CONNECTIVITY SY
5. STEMS Gigabit Ethernet SFP Media Converter The Port Status LEDs LEDs State Indication Power Steady Power on power LNKC Steady TX port A valid network connection is established LNKC stands for LINK Copper No connection LNKF Steady FX port A valid network connection is established LNKF stands for LINK Fiber No connection FDX COL Steady Connection has been made in full duplex mode FDX stands for FULL DUPLEX RX Steady Receiving data No reception TX Steady Transmitting data No transmission Functional Description e DIP switch configuration for Link Fault Signaling enable disable and fiber auto force mode 1000 Mbps Auto Full duplex Auto Negotiation Auto MDI MDIX SFP socket for Gigabit fiber optic expansion Full wire speed forwarding rate 0 8A 12VDC external universal power supply e 32 F to 113 F 0 C to 45 C operating temperature range e Aluminum case e Supports wall mounting installations or can be used with the 065 1185 media converter chassis system SIGNAMAX CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter FCC Statement The FCC Federal Communications Commission restricts the amount of radio frequency emission and radiation coming from computer equipment The equipment introduced in this manual has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rul
6. duplex mode when two 1000BaseT and 1000BaseSX LX one channel media converters are connected to each other via fiber port The TX port auto detects full and half duplex The TX port supports auto MDIX for uplink purpose 8 SIGNAMAX CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter Packing List When you unpack this product s package you will find the items listed below Please inspect the contents and report any apparent damage or missing items immediately to your authorized reseller e The Media Converter User s Manual e ACto DC Power Adaptor SIGNAMAX CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter One Channel Media Converter Physical Ports 065 1195SFP 1000BaseT to 1000Base SFP Media Converter This converter provides one TX port and one Gigabit SFP socket The Gigabit SFP socket provides the option of using multimode singlemode or WDM singlemode fiber with the appropriate SFP module The TX port uses a RJ 45 connector and supports auto MDIX for uplink purposes Port Status LEDs The LED indicators give you instant feedback on the status of the converter LEDs State Indication Power Steady Power on power LNKC Steady TX port A valid network connection is established LNKG stands for LINK Copper No connection LNKF Steady FX port A valid network connection is established LNKF stands for LINK Fiber No connection FDX
7. es These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the interference at his her own expense Any changes or modifications not expressly approved by the manufacture would void the user s authority to operate the equipment CONNECTIVITY SYSTEMS 5 IG NAM b Gigabit Ethernet SFP Media Converter Trademarks Product names mentioned in this manual may be trademarks or registered trademarks of those products All trademarks or brand names mentioned are properties of their respective companies SIGNAMAX CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter Preface This manual describes how to install and use the 065 1195SFP Gigabit Ethernet SFP Media Converter The Converter introduced here provides a one channel media conversion solution This media converter supports a 1000BaseT to 1000Base connection multimode or singlemode fiber in a variety of light spectra and span lengths with a Link Fault Signaling function A variety of Small Form factor Pluggable SFP modules allow a wide choice of
8. is The 065 1195SFP Converter is designed to fit into any of the expansion slots on a Signamax 065 1185 rack mount chassis Unscrew the carrier from the desired expansion slot on the chassis Fit the converter onto the carrier When the converter is completely seated onto the carrier insert the carrier to the guide rails of the expansion slot Carefully slide in the carrier until it is fully and firmly fit the chassis Fasten the carrier to the chassis by the screws lt NOTE gt Never insert any converter into the chassis directly without using the supplied carriers The carriers allow secure and consistent placement of the converters into the chassis backplane without causing any damage 11 SIGNAMAX CONNECTIVITY SYSTEMS Specifications Gigabit Ethernet SFP Media Converter Applicable Standards IEEE 802 3ab 1000BaseT IEEE 802 3z 1000BaseSX LX Fixed Ports 1000BaseT to 1000BaseSX LX 1 TX port 1 Gigabit SFP socket Speed 1000 2000Mbps for half full duplex Forwarding rate 1 488 100pps for 1000Mbps LED Indicators 1000T to 1000SX LX Power TX RX FDX COL LNKF LNKC Dimensions 3 16 W x 4 3 D x 0 94 H 80 3mm W x 109 2mm D x 23 8mm H Weight 0 336 150 g Power External power adaptor 0 2A 12VDC Power Consumption 2 4 Watts Maximum Operating Temperature 32 F 113 0 C 45 Storage Temperature
9. ononsecsessaseseoonascesscesenen 6 Table OF Contents ise ss0cscssccsssccscsssscssecesavescsssesssecesecesss 7 IMEPOMUCHO MN sssecsssececssssssssssasscesssssssssesasscesssssssssssassseess 8 Product OVERVIEW siscissciscdiesssectiasctecdsesaseccsasecesscessenccsseseees 8 Product 8 Packing 9 One Channel Media Converter 10 Physical Ports onines 10 Port Status LEDS 10 Install tionsssinsssnsasdnmnmnnamnnsvnnn 11 Selecting a Site for the 11 Connecting to Power ccccssssssssssecccccssssssssssecssesssseees 11 Installing in Chassis sccccccsssssssssscccssssssssssssseeeeees 11 S DOCINICAGIONS a5 scsccscstscedececscedececsssdasacesesssosesedsseseseees 12 Contact Information 13 SIGNAMAX CONNECTIVITY SYSTEMS Gigabit Ethernet SFP Media Converter Introduction The 065 1195SFP Gigabit Ethernet SFP Media Converter provides one channel for media conversion between 1000BaseT and 1000BaseSX LX with a Link Fault Signaling function It can be used as a stand alone device or with the Signamax 065 1185 16 bay Rack Mount Chassis mountable in a standard 19 rack as shown below Product Overview OOM ASE ASX LAKE PAR ke 000 _ 104 TX RX FOX Produc
10. t Features One channel media conversion between 1000BaseT and 1000BaseSX LX using SFP modules a SFP socket is provided to accommodate Gigabit Ethernet SFP s Fiber media can be either multimode fiber singlemode fiber or WDM singlemode fiber Full wire speed forwarding rate Front panel status LEDs Used as a standalone device or with the Signamax 065 1185 rack mount chassis Hot swappable when used with the Signamax 065 1185 rack mount chassis A connection the TX port must be made before making a connection to the fiber port so that a link condition will be sensed on the fiber port whenever the media converter detects a link condition on the TX port There are two pins on the DIP switch of the 1000BaseT and 1000BaseSX LX one channel media converter gt Toggle up the pin on the left hand side to let the fiber port auto detect full and half duplex gt Toggle down the pin on the left hand side to force the fiber port to full duplex mode gt Toggle up the pin on the right hand side to disable the link fault pass through function gt Toggle down the pin on the right hand side to enable the link fault pass through function DIP Up Default Setting Down Notes Switch Left hand The fiber port auto Force the fiber port to full side detects full and half duplex mode duplex Right hand Disable LFS Enable LFS LFS Link Fault side Signaling function The fiber port should be forced to full
Download Pdf Manuals
Related Search