CSB200-883 User Manual - IBT Technologies Inc.
Contents
1. Using attached mounting rail you can install CSB200 on wood drywall surface over studs or a solid concrete or metal plane Ensure the installer uses at least four M4 length 8mm screws to secure the system on wall Six M4 length 8mm screws are recommended to secure the system on wall Fasteners are not included with the unit and must be supplied by the installer The types of fasteners required are dependent on the type of wall construction Choose fasteners that are rated either Medium Duty or Heavy Duty To assure proper fastener selection and installation follow the fastener manufacturer s recommendations Wall mounting requirements Note Before mounting the system on wall ensure that you are following all applicable building and electric codes When mounting ensure that you have enough room for power and signal cable routing And have good ventilation for power adapter The method of mounting must be able to support weight of the CSB200 plus the suspend weight of all the cables to be attached to the system Use the following methods for mounting your system 11 Mounting to hollow walls m Method 1 Wood surface minimum wood thickness 38mm 1 5in by 25 4 cm 10in of high construction grade wood is recommended Note This method provides the most reliable attachment of the unit with little risk that the unit will come loose or require ongoing maintenance m Method 2 Drywall walls D2. 2 Components Front View Refer to the diagram below to identify the components on this side of the system amp PWR Il USB HDD RST ON OFF ON OFF The power switch allows powering ON and OFF the system RST The reset switch allows reset the system HDD The hard disk LED blinks when data is being written into or read from the hard disk drive PWR The power LED illuminated when system been power on USB The USB Universal Serial Bus port is compatible with USB devices such as keyboards mouse devices cameras and hard disk drives USB allows many devices to run simultaneously on a single computer with some peripheral acting as additional plug in sites or hubs SPK The stereo audio jack 3 5mm is used to connect the system s audio out signal to amplified speakers or headphones MIC The microphone jack is designed to connect the microphone used for video conferencing voice narrations or simple audio recordings Rear View Refer to the diagram below to identify the components on this side of the system USE LAI LAN mM IT 1111 oo bo COM1 2 Communication or serial port one is compatible with RS 232 interface VGA Video Graphic Array VGA port supports a VGA compatible de
3. CSB200 883 User Manual 2009 April V1 0 Copyright 2008 IBASE Technology INC All Rights Reserved No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of IBASE Technology INC IBASE Products and corporate names mentioned in this manual may or may not be registered trademarks or copyrights of their respective companies and are used for identification purposes only All trademarks are the property of their respective owners Every effort has been made to ensure that the contents of this manual are correct and up to date However the manufacturer makes no guarantee regarding the accuracy of its contents and reserves the right to make changes without prior notice Table of Contents Pu ad 220 41 SSR EEE PIERRE EEE PER eaneane en a tr tel Ad Ta at et r scene eee 6 Components nennen seine etes ass eecesns etes te dti ete tentes 7 Front View wiisccscichsvessedsdecsedessesbensssosssacesssesesdoctaeseaeedsudesesstessanss esis deseasesvosaudevassedsasestendess 7 Rear VA LS RER RE os d addeescsavoossd aceoseccas 8 SpeCIRCOtIO Me Ah nent raie ea Taaa 10 Mounting CSB200 to the Wall nantes 11 Wall mounting requirements ssesssssssssoosssseossseosssssossssoss
4. rywall over wood studs is acceptable Mounting to a solid concrete or brick wall Mounts on a flat smooth surface Selecting the location Plan the mounting location thoroughly Locations such as walkway areas hallways and crowded areas are not recommended Mount the unit to a flat sturdy structurally sound column or wall surface The best mounting surface is a standard countertop cabinet table or other structure that is minimally the width and length of the unit This recommendation reduces the risk that someone may accidentally walk into and damage the device Local laws governing the safety of individuals might require this type of consideration 12 Exploded view of the CSB200 883 assembly Parts description Part NO Description Part NO Description 1 Top Cover 2 SATAHDD 3 Base Chassis 4 SATA Cable 5 DC Jack Extension Cable 6 COM1 2 Extension Cable 7 VGA Extension Cable 8 IB883 9 ID737A 10 Mounting rail 11 VO wall panel 13 Driver Installation Please refer correspond mainboard user manual to install the driver properly BIOS Setup Please refer correspond mainboard user manual to configure BIOS setting 14
5. sssoosessosssssossessossesscssessooses 11 Selecting the location assaisonner aAA E NEANS RE EaR AA AEEA REAREN A E SAONE AEE a 12 Exploded view of the CSB200 883 assembly 13 Parts descriptiOn i ccisccdcssseesdecsseccinesbeestecdsnsesdusscciawcvessdacedtecdseaessescus rente nl tes done tete ns tee 13 Driver instalation sinistre 14 BIOS Setup asien Rena 14 Safety Information Your CSB200 883 is designed and tested to meet the latest standards of safety for information technology equipment However to ensure your safety it is important that you read the following safety instructions Setting up your system Read and follow all instructions in the documentation before you operate your system Do not use this product near water Set up the system on a stable surface or secure on wall with the provided rail Do not secure the system on any unstable plane or without the rail Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product Slots and openings on the chassis are for ventilation Do not block or cover these openings Make sure you leave plenty of space around the system for ventilation Never insert objects of any kind into the ventilation openings This system should be operated from the type of power indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company Use this product in environments
6. vice such as a monitor or projector The system default display output port DC IN The supplied power adapter converts AC power to DC power for use with this jack Power supplied through this jack supplies power to the system To prevent damage to the system always use the supplied power adapter DVI The Digital Visual Interface DVI port supports a high quality VGA compatible device such as a monitor or projector to allow viewing on a larger external display LAN The eight pin RJ 45 LAN port supports a standard Ethernet cable for connection to a local network USB The USB Universal Serial Bus port is compatible with USB devices such as keyboards mouse devices cameras and hard disk drives USB allows many devices to run simultaneously on a single computer with some peripheral acting as additional plug in sites or hubs KB MS You can connect PS 2 compatible device into this port directly or using Y cable to have PS 2 mouse port extension MS The PS 2 mouse port is use to connect PS 2 mouse KB The PS 2 keyboard port is use to connect PS 2 compatible devices such as keyboard MSR and scanner Specification System Mainboard B883 Construction Chassis Color Storage emperature Storage emperature Relative Humidity 172 W x 52 H x 113 6 D mm 80W DC adapter 0 C 45 C 32 F 113 F 20 C 80 C This specification is subject to change without prior notice 10 Mounting CSB200 to the Wall
7. with ambient temperatures between 0 C and 45 C If you use an extension cord make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating Care during use Do not walk on the power cord or allow anything to rest on it Do not spill water or any other liquids on your system When the system is turned off a small amount of electrical current still flows Always unplug all power and network cables from the power outlets before cleaning the system If you encounter the following technical problems with the product unplug the power cord and contact a qualified service technician or your retailer gt The power cord or plug is damaged gt Liquid has been spilled into the system gt The system does not function properly even if you follow the operating instructions gt The system was dropped or the cabinet is damaged Lithium lon Battery Warning CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions NO DISASSEMBLY The warranty does not apply to the products that have been disassembled by users Accessories CE ET a Power Cord x 1 b M B Manual x 1 D c Driver CD x 1 QVYVGVSYSYVS SVs Vy amp d Power Brick x 1 e Mounting Rail Screw x 4 f Mounting Rail x
Download Pdf Manuals
Related Search