SAVE THESE INSTRUCTIONS OPERATING INSTRUCTIONS
Contents
1. 1 2 12 5mm e Long comb attachment number 5 cuts hair to 5 8 16mm e Long comb attachment number 6 cuts hair to 3 4 19mm e Long comb attachment number 7 cuts hair to 7 8 22mm e Long comb attachment number 8 cuts hair to 1 25mm e Left ear comb attachment lightly tapers over left ear e Right ear comb attachment lightly tapers over right ear Attach combs by them teeth up then snapping onto the bottom of the clipper blade To remove comb attachments place index finger and thumb as illustrat ed then pull out and up NOTE Never push or shove the clipper through the hair to make it move more quickly Professional experience shows that the clipper works most efficiently when it cuts through the hair at its own speed To begin cutting hair 1 The hair should be combed in its natural direction 2 Using the largest comb attachment trim sides from the bottom upward Hold clipper lightly against the hair with teeth of the comb attachment pointing upward yet flat against the head Gradually lift the clipper upward and outward through the hair trimming just a little at a time Repeat around sides and back of head If you want hair to be even shorter A Apply more pressure to the head with the comb attachment that is in place This takes a little practice of course OR B Just switch to a shorter comb attachment Remember it s better to leave too much hair2. than too little For longer hair on top use the barber comb and lift hair on the top of the head cutting over the comb Or hold the hair between the fingers and cut to desired length Always working from the front to the back of the head gradually cut the hair shorter by reducing the space between the comb or fingers and the head Comb often to check for uneven strands and to get rid of trimmed hair OUTLINING Outlining requires no attachments Comb hair into the desired style Position the clip per between the sideburns and the ear see above making sure the corner edge of the blade is against the hairline With the outline of the hair as your guide slowly move the clipper over around and behind the ears For the back of the neck and the sideburns hold the clipper upside down see above and holding it against the skin at the length desired move the clipper downward STOP COMB CHECK For best results do as the professionals do comb hair often and check clipping results as you comb This way you avoid uneven sides bangs neckline etc SHORT CUTS TO PERFECT FLAT TOPS CREW CUTS ETC Always cut from the back of the neck to the crown using the longest comb setting Hold the comb attachment flat against the head and slowly move the clipper up through the hair Use the same technique for the sides cutting from the bottom to the upper side of the head For the front to the crown cut the hair against the d
3. of charge for 36 months from the date of purchase if the appliance is defective in work manship or materials To obtain service under this warranty return the defective product to the service centre listed below together with your purchase receipt and 7 50 for postage and handling In the absence of a purchase receipt the warranty period shall be 3 years from the date of manufacture ANY IMPLIED WARRANTIES OBLIGATIONS OR LIABILITIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE 36 MONTH DURATION OF THIS WRITTEN LIMITED WARRANTY IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED WHATSOEVER This warranty gives you specific legal rights and you may also have other rights which vary from province to province SUPER 4 LITHIUM ION SERIES Full Power Cord Free Cutting SERVICE CENTRE 2013 CONAIR CONSUMER PRODUCTS ULC Hetrechen pooner 100 Conair Parkway For your safety and continued enjoyment of this product always read the instruction booklet carefully before using Model HC1100LIC Woodbridge Ontario L4H OL2 For more information on any Conair product call 1 800 472 7606 Visit our Web site www conaircanada ca Consumer Call Centre E mail Consumer_Canada Conair com 130N143231 IB 12316
4. IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances especially when children are present take basic safety precautions including the following READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER FOR HOUSEHOLD USE ONLY DANGER any appliance is electrically live even when the switch is off To reduce the risk of death or injury by electric shock 1 Unplug this appliance before cleaning 2 Do not place or store appliance where it can fall or be pulled into a tub or sink 3 Do not use while bathing or in a shower 4 Do not place in or drop into water or other liquids 5 Do not reach for an appliance that has fallen into water Unplug immediately For dry location use only Do not expose to liquid vapor or rain 6 Except when charging always unplug this appliance from electrical outlet immediately after using WARNING To reduce the risk of burns electric shock fire or injury to persons 1 This appliance should never be left unattended when plugged in Do not pull twist or wrap line cord around appliance 2 This appliance should not be used by on or near children or individuals with certain disabilities 3 Use this appliance only for its intended purpose as described in this manual Do not use attachments not recommended by the manufacturer Do not use an extension cord to operate this appliance 4 Never operate this appliance if it has a damaged cord or plug if it is not wo
5. NG Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment SAVE THESE INSTRUCTIONS OPERATING INSTRUCTIONS USER MANUAL Before using the Class 2 Power Supply read these instructions carefully Rated input voltage 100 240V AC 50 60HZz 0 2A Max Rated output 4 5 VDC 1000mA OPERATION 1 For dry location use only Do not expose to water 2 When not in use unplug unit completely 3 Unit will become warm during operation CAUTION 1 Dry location use only Do not expose to liq uid vapor or rain 2 Ensure jack is plugged into the trimmer unit before plugging the adapter into the outlet 3 Do not operate any appliance that has a damaged output cord or housing 4 Always unplug the unit before cleaning or when not in use 5 This power unit is intended to be correctly oriented in a vertical or floor mount position 6 Be sure voltage is in correct voltage before plugging in FEATURES e Cord or cordless operational clipper use corded for continuous power while plugged into the outlet or use cordless for total flexibility and control e Lithium ion technology with lightweight DC motor for powerful cutting action and sustained power performance e Precision engineered high grade hardened steel blades with unique super sharp cutting angle for smooth effortless cutting e Lightweight for eas
6. an hold the clipper in your hand and adjust the lever at the same time while you re clipping This taper lever eliminates the need in some situations for a comb attachment because it lets you gradually adjust the closeness of the cut For the closest cut and the shortest hair push taper lever up as far as it will go to level 1 To increase cutting length slowly push lever down If you push to the lowest position level 5 it will leave hair about the same length as the short comb attachment Because a different cutting edge is used in each setting the taper lever lengthens the life of your blades Packed in hair can slow down any clipper To remove hair without removing the blades do what the professionals do keeping the clipper on quickly push the taper lever back and forth from close to longer cut a few times lf you do this after every clipping especially with heavy hair cutting the blades should remain free of cut hair If clipper stops cutting and this action doesn t help check the blades If they ve become dull replace them For new blades send check or money order for 6 50 which includes postage and handling if 10 minimum is met to 2013 CONAIR CONSUMER PRODUCTS 100 Conair Parkway Woodbridge ON L4H OL2 NOTE Never pull on the clipper cord Never twist or wrap the cord around the clipper Lay it flat with the cord coiled up when not in use STORAGE When not in use your cli
7. ing light suddenly starts to flash rapidly the appliance is faulty If this happens please stop charging and remove the adapter from the outlet and contact our Customer Care Center for further advice see the Warranty section of the information booklet CORDED OPERATION e Ensure the appliance is switched off e Connect the adapter to the base of the appliance and plug the adapter into a suitable outlet e The red LED charging light will go on when the adapter is correctly inserted into the appliance and connected to an outlet e The appliance is now ready for use CORDLESS OPERATION e Insert the adapter into the base of the appliance plug into a suitable outlet e Unplug the adapter from the outlet once the green LED charging light goes on as the appliance is now fully charged OILING INSTRUCTIONS IMPORTANT It is highly recommended before each use to oil the blades with the oil provided This ensures optimum cutting performance For the first use you will need to use the oil supplied with the product Unscrew the cap and cut off the very end of the plastic tube with a pair of scissors to release the oil To oil the blades ensure that the unit is switched on Gently squeeze the oil tube and apply 2 drops of oil to the blades see FIG 1 2 and 3 Leave the unit on for a few seconds to allow the oil to thoroughly spread the length of the blades Switch off the unit and remove any excess oil by gently dabbing with a cl
8. irection in which it grows Then even it up with the sides For a flat top use the flat comb not the comb attachment Just cut hair on top of the head over flat comb see below USER MAINTENANGE INSTRUCTIONS CARE OF YOUR CLIPPERS IF YOU DETERMINE THAT BLADE ALIGNMENT IS INCORRECT Conaire hair clippers are carefully inspected to ensure that the blades are in perfect align ment Of course you will need to realign the blades after removal for cleaning or replace ment or if they should be knocked out of alignment How can you tell if blades need realigning Simply match them up point for point to conform with FIG 1 below Top Blade RHIAN T Si EANN FIG 1 To prevent the clipper from contacting the skin or cutting too closely make certain that the end top blade teeth are 1 32 to 1 16 back from bottom blade To Align Blades 1 Add two or three drops of Conair Lubricating Oil included 2 Turn clipper on for a minute to disperse oil evenly over blades then turn off 3 Unplug clipper and slightly loosen screws See FIG 2 4 Position the extreme left hand tooth of the top blade so that it either covers or appears on the left of the first small tooth on the bottom blade 5 Make sure that the big tooth on the bottom blade touches the extreme right hand tooth of the top blade ADJUSTABLE TAPER LEVER Just like professional clippers the Conair taper lever is positioned at your thumb You c
9. oth Be careful not to use too much oil and don t oil your clipper more than necessary as this could damage the motor Never attempt to oil the motor bearing as it is permanently lubricated KEEP OIL OUT OF REACH OF CHILDREN icone PA OIL BOTH AREAS N PRESERVING THE BATTERIES In order to maintain the optimum capacity of the rechargeable batteries the appliance has to be fully discharged approximately every 6 months Then recharge the appliance to full capacity again for 3 hours THE CONAIR GUIDE TO CUTTING HAIR AT HOME Before you start 1 Inspect your clipper Make sure it s free of hair and dirt properly oiled and running smoothly 2 Place a towel around the neck of the person whose hair is to be cut 3 Seat the person so that his or her head is at your eye level This gives you greater visibility and control 4 First comb hair until it s tangle free Then hold clipper in a comfortable grip Now you re ready to cut MEDIUM TO LONG CUT To begin cut only a small amount of hair until you become used to the length each attachment leaves the hair Try the longest attachment on the clipper first If you want a shorter cut you can then use shorter combs e Short comb attachment number 1 cuts hair to 1 8 3mm e Medium Short comb attachment number 2 cuts hair to 1 4 6mm e Medium Long comb attachment number 3 cuts hair to 3 8 9 5mm e Long comb attachment number 4 cuts hair to
10. pper should be disconnected allowed to cool and stored in a safe dry location out of reach of children Any other servicing should be performed by authorized service representative This appliance has no user serviceable parts This appliance is for household use Close Cut Longer Cut BATTERY DISPOSAL This appliance contains a lithium ion battery To protect the environment this appliance and its battery must be disposed of safely At the end of its life please take this appliance to a recycling center where the internal rechargeable battery should be removed by a professional and recycled separately For more information about the recycling of electrical and battery operated appliances please contact your local recycling or environmental protection office or your household waste disposal service For specific enquiries regarding the replacement of batteries in this product please contact our Conair Customer Care Line HC1100LIC CORD CORDLESS CLIPPER Stainless steel self sharpening TTT TTET blades A N CONTAINS LITHIUM ION a BATTERY MUST BE COLLECTED RECYCLED OR DISPOSED OF PROPERLY N Zi DO NOT DISPOSE OF IN THE MUNICIPAL WASTE Taper control High power motor On Off switch A QUICKCHARGE 3 hour full charge for 75 minutes of use or 20 minute quick charge for 10 minutes of use LIMITED THREE YEAR WARRANTY Conair will repair or replace at our option your unit free
11. rking properly or if it has been dropped or damaged or dropped into water Return the appliance to a service center for examination and repair 5 Keep the cord away from heated surfaces 6 Never drop or insert any object into any Opening on this appliance 7 Do not place appliance on any surface while it is operating 8 Do not use this appliance with a damaged or broken comb or with teeth missing from the blades as injury may occur Before use make certain blades are aligned properly 9 Do not use outdoors or operate where aerosol spray products are being used or where oxygen is being administered 10 Never operate the appliance with the air openings blocked or while on a soft surface such as a bed or couch where the air openings may be blocked Keep the air openings free of lint hair and other debris 11 Always attach plug to appliance first then to outlet To disconnect turn all controls to OFF then remove plug from outlet 12 Avoid skin coming into contact with moving blade 13 When using the appliance with its cord be mindful of tangles or kinks in the cord If the cord does become tangled during use turn the unit off and straighten cord before Operating again 14 Do not short the polarity output cord ensure jack is plugged into the unit before plugging the adapter into outlet 15 This power unit is intended to be correctly oriented in vertical floor mount position 16 CAN ICES 3 B WARNI
12. y handling during use e Taper control for custom settings e 3 hour full charge for approximately 75 minutes of use e 20 minute quick charge for approximately 10 minutes of use Also included are 10 comb attachments for different hair lengths including left and right ear taper combs barber scissors a barber comb with straight teeth styling comb with angled teeth a full length barber cape and a deluxe case for easy storage It also comes with lubricating oil a cleaning brush and a blade guard for easy maintenance and protection of the clipper blades INSTRUCTIONS FOR USE CHARGING THE APPLIANCE IMPORTANT Use only the adapter supplied with this appliance This clipper is easy to use but before you do anything you must take your time to charge the unit for 3 hours before its first use Even if you want to use it plugged in straight from an outlet this initial supercharge ensures optimum power performance to give smooth fast cutting every time Maximum battery capacity will be reached only after 3 Charging discharging cycles A full charge will provide approximately 75 minutes use When the clipper is about to run out of power the charging indicator will flash and you will have approximately 3 minutes of use remaining A 20 minute quick charge will provide approximately 10 minutes use The red LED light will go on when charging the appliance and the green LED light will go on when fully charged WARNING If the charg
Download Pdf Manuals
Related Search