User Manual
Contents
1. Adjustment Hole Button Head Adjustment Swingaway Screw Threaded Rivet Hole footrest shown Footplate Cam Lock Lever Footplate Assembly Assembly Inside of Swingaway Front Riggin BANAR Eme Outside of Swingaway Front Rigging FIGURE 3 Adjusting Footplate Height Bolt In Place Invacare Tracer EX2 Wheelchair 32 Part No 1110546 Fixed Frame l 2 5 3 Remove impact guards and or calf strap if necessary Loosen but do not remove the bolt and locknut that secure the lower footrest assembly to the upper footrest support Reposition the lower footrest assembly to the desired height Securely tighten the bolt and locknut Repeat this procedure for the other footrest if necessary Replace impact guards and or calf strap if necessary Raising Lowering Elevating Legrest Assembly A WARNING Ensure hands and fingers are clear of elevating legrest mechanism before pushing release lever to lower the elevating legrest Otherwise injury may occur due to pinch points The wheelchair user s leg MUST be supported by an assistant before attempting to lower legrest To raise the elevating legrest the assistant should hold the support tube and raise the elevating legrest until the desired height is obtained To lower the elevating legrest perform the following A Support user leg with one hand B Push release lever downward with other hand C Gently lower user leg down and rest2. Repeat STEPS 1 2 for opposite crossbrace Reverse STEPS 3 to assemble the upper mounting hardware Reverse STEPS 1 4 in Removing Lower Mounting Hardware DETAIL A REMOVING LOWER Crossbrace MOUNTING HARDWARE MOUNTING HARDWARE Rear Seat Guide nos Crossbrace Locknut Insert Tube Hex Screw Wheelchair Frame Front Seat Guide FIGURE 7 Adjusting the Seat Width Fixed Frame Part No 1110546 43 Invacare Tracer EX2 Wheelchair 8 REAR WHEELS 8 Rear Wheels WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 8 1 Replacing Repairing Rear Wheel Tire A WARNING Replacement of the rear wheel tire MUST be performed by a qualified technician As with any vehicle check the wheels and tires periodically for cracks and wear Replace if damaged 8 2 Removing Installing Rear Wheels A WARNING Only a qualified technician may change the size of the rear wheel or the seat to floor height If changing the size of the rear wheel or a change in the seat to floor height is desired this procedure MUST be performed by a qualified technician Make sure both rear wheels are the same size and are installed into the same respective mounting hole before using the wheelchair otherwise injury may occur Permanent Axles WARNING This procedure MUST be performed by a qualified technician If replacing
3. Part No 1110546 63 Invacare Tracer EX2 Wheelchair Part No 1110546 Rev H 6 13 Invacare Corporation USA One Invacare Way Elyria Ohio USA 44036 2125 800 333 6900 www invacare com Canada 570 Matheson Blvd E Unit 8 Mississauga Ontario L4Z 4G4 Canada 800 668 5324 Yes you can
4. make sure that the footplates are in the upward position ALWAYS use the handrims for self propulsion Invacare recommends that a non folding device be installed to keep the wheelchair from being folded when left unoccupied in a public place DO NOT operate on roads streets or highways DO NOT allow children to play on or operate the wheelchair DO NOT operate on soft surfaces such as sand grass or gravel DO NOT overtighten hardware attaching to the frame This could cause damage to the frame tubing Hand Grips WARNING ALWAYS check hand grips for looseness before using the wheelchair If loose and or worn replace IMMEDIATELY When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water Verify that grips are dry prior to use Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly Failure to observe this warning may result in injury to the user or bystanders If the wheelchair is exposed to extreme temperature above 100 F or below 32 F high humidity and or becomes wet prior to use ensure that the handgrips DO NOT twist on the handle Otherwise damage or injury may occur Invacare Tracer EX2 Wheelchair 12 Part 1110546 3 SAFETY Information for Healthcare Professionals Assistants A WARNING When assistance to the wheelchair user is required remember to use good body mechanics Keep your back straight and bend your knees w
5. against the legrest Part No 1110546 33 5 FRONT RIGGINGS Wheelchair Frame Footplate Assembly FIGURE 4 Adjusting Footplate Height Fixed Frame Release Lever FIGURE 5 Raising Lowering Elevating Legrest Assembly Invacare Tracer EX2 Wheelchair 5 FRONT RIGGINGS 5 4 Replacing Heel Loop For this procedure refer to FIGURE 6 on page 35 Pull the cam lock lever up to unlocked position Perform one of the following Footplates with Spring Buttons Detail A i Push in the release buttons and remove the footplate assembly from the front rigging support Bolt In Place Footplates Detail i Using a screw driver to hold the threaded rivet in position remove the button head screw from the threaded rivet ii Remove the threaded rivet and button head screw securing the footplate assembly to the front rigging support Remove the mounting screw spacer and locknut that secure the heel loop to the footplate Remove existing heel loop from slide tube Install new heel loop onto slide tube Install the mounting screw spacer and locknut to secure the heel loop to the footplate Tighten until the spacer is secure Insert the lower footrest assembly into the upper footrest assembly to desired height Perform one of the following Footplates With Spring Buttons Detail A L Ensure that the release buttons fully protrude from holes on both sides of the upper footrest suppor
6. and replace 3 Check all parts for proper adjustment A CAUTION As with any vehicle check the wheels and tires periodically for cracks and wear Replace if damaged Replace as recommended refer to Replacing Repairing Rear Wheel Tire Tube on page 29 and Replacing Repairing Caster Tire Tube on page 29 The rear wheels casters and tires should be checked periodically for cracks and wear and should be replaced by a qualified technician if damaged 5 Periodically adjust wheel locks in correlation to tire wear Refer to Adjusting Patient Operated Wheel Locks on page 55 Invacare Tracer EX2 Wheelchair 28 Part No 1110546 4 SAFETY INSPECTION TROUBLESHOOTING Tire wear is excessive if Pneumatic Tires there is missing tread or the tires are bald Urethane Tires there are cuts surface defects or the tires are loose on the rims Rubber Tires 30 or more of the tire has worn away Invacare recommends that tires and casters be replaced every five years Periodically check handrims to ensure they are secured to the rear wheels If loose have them tightened by a qualified technician Periodically check caster wheel bearings to make sure they are clean and free from moisture Use a Teflon lubricant if necessary Check upholstery for sagging rips or tears Clean upholstery with mild soap and water POND 0 Hand grips should be checked monthly for wear looseness deterioration Clean if desired Replace if loosenes
7. strongly recommends ordering the seat positioning strap as an additional safeguard for the wheelchair user The seat positioning strap is a positioning strap only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear strap MUST be replaced IMMEDIATELY With regards to seat chest positioning straps it is the obligation of the DME dealer therapists and other healthcare professionals to determine if a seat chest positioning strap is required to ensure the safe operation of this equipment by the user Serious injury can occur in the event of a fall from a wheelchair Invacare Tracer EX2 Wheelchair 14 Part No 1110546 3 SAFETY Stability All Models A WARNING The seat depth size position of the front casters size position of the rear wheels use of anti tipper model as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the seven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician The various seat to floor heights require specific settings depending on rear wheel size rear wheel position front caster size position and desired seat to floor angle These adjustments MUST be performed by a qualified technician When changes to the left hand column occur follow across the chartand N z N z e dee a x 5 m r
8. the same size rear wheel note the mounting position on the wheelchair frame for proper reinstallation of the new rear wheel Invacare Tracer EX2 Wheelchair 44 Part No 1110546 8 REAR WHEELS Remove the dust cap SA Frame only hex screw washer SA Frame only spacer if installed and locknut that secure the rear Axle Mounting Axle Rear Wheel P di Locknut wheel to the wheelchair frame Washer ae The spacer is used on wheelchairs with removable arms SA Frame Y only ONLY 2 Repeat STEP for the opposite rear wheel if desired Dust Cap 3 Toreinstall the rear wheel s onto the wheelchair reverse STEPS SA F 1 2 and torque locknut to 40 ft Ibs Ge 4 Adjust wheel locks Refer to Using Adjusting Patient Operated Wheel Locks on page 54 Wheelchair Frame me ONLY Spacer Wheelchairs with Removable Arms ONLY FIGURE Removing Installing Rear Wheels Permanent Axles Quick Release Axles If replacing the same size rear wheel note the mounting position on the wheelchair frame for proper reinstallation of the new rear wheel Push in the detent pin of quick release axle with wheel and pull the axle out through the opening in the center of the rear wheel and axle spacer Q Axle spacer is used only if wheelchair is equipped with conventional arms 2 Push in the detent pin of the quick release axle again and pull the axle out of the rear wheel 3 Repeat STEPS 1 2 for the opposite
9. NG As with any vehicle check the wheels and tires periodically for cracks and wear Replace if damaged If equipped check that the quick release axles lock properly Lubricate if necessary Check that there is no excessive side movement or binding in the rear wheels when lifted and spun Inspect rear wheels for cracked bent or broken spokes Ensure all spokes are uniformly tight Inspect handrims for signs of rough edges or peeling Inspect axle assembly for proper tension by spinning caster Caster should come to a gradual stop Adjust front casters forks bearing system if wheel wobbles noticeably or binds to a stop Ensure wheel bearings are clean and free of moisture Check headtube locknuts for tightness Inspect casters for cracks and wear Inspect front casters for cracked bent or broken spokes Ensure that casters are free of debris Clean upholstery and armrests with mild soap and water D CO CO D O CO O DO O OO UcOCU Check that all labels are present and legible Replace if necessary Inspect Adjust Weekly Q Ensure that the wheel locks prevent the wheelchair from moving when engaged Inspect tires for flat spots and wear Check pneumatic tires for proper inflation If equipped check that the quick release axles lock properly Lubricate if necessary Inspect rear wheels for cracked bent or broken spokes UUUU LU Ensure all spokes are uniformly tight Part No 1110546 25 Invacare Tracer EX2 Wheelchair 4 a a
10. Remove rear wheel and quick release axle from the wheelchair Refer to Removing Installing Rear Wheels on page 44 2 Depress detent pin in the quick release axle and slide axle through the rear wheel hub Axle Bushing Quick Release 3 Release detent pin ensuring that the detent balls are fully released 4 Increase or decrease end play by adjusting the locknut the end Detent Balls of the quick release axle Detent Pin WARNING A Locknut Make sure detent pin and detent balls of the quick release axles are fully released before operating the wheelchair Axle Spacer Conventional Arms Only Rear Wheel Hub Keep detent balls clean 5 Reinstall rear wheel onto the wheelchair Refer to Removing FIGURE 3 Adjusting Quick Release Axle Installing Rear Wheels on page 44 Part No 1110546 47 Invacare Tracer EX2 Wheelchair 8 REAR WHEELS 8 4 Replacing Rear Wheel Handrim A WARNING If the wheelchair is equipped with permanent axles this procedure MUST be performed by a qualified technician 1 Remove the rear wheel from the wheelchair Refer to Removing Rear Wheel Installing Rear Wheels on page 44 e Mounting Screw 2 Remove the mounting screws that secure the handrim to rear wheel 3 Remove the existing handrim Handrim 4 Secure the new handrim to the rear wheel with mounting screws Tighten securely A WARNING Make sure the dete
11. Rigging Support Adjusting Footplate Height Spring Button Invacare Tracer EX2 Wheelchair 5 FRONT RIGGINGS Bolt In Place This procedure applies to the swingaway front riggings and swingaway elevating legrest Remove the swingaway front rigging Refer Installing Removing Front Riggings on page 30 Lay the front rigging assembly on a flat surface to simplify this procedure Pull the cam lock lever up to the unlocked position Using a screw driver to hold the threaded rivet in position remove the button head screw from the threaded rivet Remove the threaded rivet and button head screw securing the footplate assembly to the front rigging support Adjust the footplate assembly height by aligning the desired adjustment holes in the upper front rigging support and lower footplate assembly From the outside of the swingaway front rigging insert the threaded rivet through both the front rigging support and the footplate assembly From the inside of the swingaway front rigging insert the button head screw through the appropriate adjustment hole and thread into the threaded rivet Using a screwdriver to hold the threaded rivet in position securely tighten the button head screw Torque to 32 in lbs Rotate cam lock lever down to locked position Repeat STEPS 1 9 to adjust the remaining footrest Front Rigging Support Button Head Screw _ Threaded Rivet Front Rigging Support
12. User Manual GO Invacare Tracer EX2 Wheelchair This manual MUST be given to the user of the product BEFORE using this product read this manual and save for future reference Yes you can 2013 Invacare Corporation All rights reserved Republication duplication modification in whole in part is prohibited without prior written permission from Invacare Trademarks are identified by and All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted Teflon is a registered trademark of DuPont Invacare Tracer EX2 Wheelchair 2 Part No 1110546 GENERAL LE Limited Warranty ENEE OVERVIEW Label Locatioris ptt tetti tt te tea a tero PEEL utes Component Identification ENEE Typical Product Parameters SAFETY General Guidelines Safety Handling of Wheelchairs eterne tentent SAFETY INSPECTION TROUBLESHOOTING Safety Inspection Checker lee E W FRONT RIGGINGS Installing Removing Front Riggings eene tnnt Adjusting Footplate Raising Lowering Elevating Legrest Assembly ENEE Repl cing Heel Eo6p iech ARMS Adjusting Armrest Removing Installing 5 Replacing Back Upholstery Replacing Seat Uphol
13. W LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE EXCLUSION AND LIMITATION MAY NOT BE APPLICABLE THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS Invacare Tracer EX2 Wheelchair 6 Part No 1110546 2 OVERVIEW 2 Overview 2 1 Label Locations NO WHEELCHAIR HAS BEEN APPROVED FOR USE AS A SEATING SURFACE WITHIN A MOTOR VEHICLE THIS LABEL IS FOR INFORMATIONAL PURPOSES ONLY LIABILITY ISSUES WERE NOT CONSIDERED IN THE ATTACHMENT OF THIS LABEL Serial Number Label located on X Brace that attaches at the left hip AUCUN FAUTEUIL ROULANT N A T APPROUV POUR TRE UTILIS COMME SI GE L INT RIEUR D UN V HICULE MOTORIS CETTE TIQUETTE NE PEUT TRE UTILIS E QU TITRE D INFORMATION ET N A PAS T AFFICH E ICI POUR DES RAISONS DE RESPONSABILIT LEGALE Crossmember WEIGHT CAPACITY Lower Frame 250 LBS 114 kgs Tube REFER TO OWNER S MANUAL P N 1111013 On all adjustable anti tippers ZNWARNING WARNING Do not operate without the anti Refer to the Owner s Manual tip tubes installed 7 AVERTISSEMENT a Senet NE PAS utiliser sans d abord Z NAVERTISSEMENT avoir install les antibascules No 1091552 Se r f rer au manuel de l utilisateur pour le r glage ad quat de l antibascule No 1091554 Part No 1110546 7 Invacare Tracer EX2 Wheelchair 2 OVERVIEW 2 Component Identification Back U
14. a SAFETY INSPECTION TROUBLESHOOTING Inspect axle assembly for proper tension by spinning caster Caster should come to a gradual stop Inspect front caster for cracked bent or broken spokes Ensure that casters are free of debris Inspect Adjust Monthly Oooo Oooo Ensure that the wheelchair rolls straight no excessive drag or pull to one side Check that the wheel locks DO NOT interfere with tires when rolling Check that the wheel lock pivot points are free of wear and looseness Inspect seat and back for loose or broken hardware Inspect seat positioning strap for any signs of wear Ensure buckle latches Verify hardware that attaches strap to frame is secure and undamaged Replace if necessary Inspect back cane hand grips for wear looseness deterioration Adjust front casters forks bearing system if wheel wobbles noticeably or binds to a stop Ensure wheel bearings are clean and free of moisture Check headtube locknuts for tightness Inspect Adjust Periodically m Cooooodno Inspect frame and crossbraces for loose or missing hardware Inspect for bent frame or crossbraces Check that wheel locks are easy to engage Inspect seat and backs for rips and sagging Check that there is no excessive side movement or binding in the rear wheels when lifted and spun Inspect handrims for signs of rough edges or peeling Adjust front casters forks bearing system if wheel wobbles noticeably or binds to a stop E
15. alling Replacing Front Casters Forks Invacare Tracer EX2 Wheelchair 9 FRONT CASTERS 92 Adjusting Forks properly tighten caster journal system and guard against flutter perform the following check Tip back of wheelchair to floor Pivot both forks and casters to top of their arc simultaneously Let casters drop to bottom of arc wheels should swing once to one side then IMMEDIATELY rest in a straight downward position Adjust locknuts according to freedom of caster swing Repeat STEPS C D until wheels swing once to one side then IMMEDIATELY rest in a downward position Test wheelchair for maneuverability gt Readjust locknuts if necessary and repeat STEPS 1 2 until correct 4 Snap dust cover over the locknut and stem 9 3 Replacing Front Casters WARNING 6 or 8 inch i A Fork d Locknut Make sure both front casters are the same size and are ME installed into the same respective mounting hole before Hel sasaw using the wheelchair otherwise injury may occur Se Note the mounting position on the fork assembly for 2 Washer proper reinstallation of the new front caster if applicable 1 Remove the hex screw washers and locknut that secure the front caster to the fork Q Washers are only used with 8 inch casters with e Ce Front Caster precision bearings 2 reinstall the new front caster onto the fork reverse step Washer if applicable FIGURE 2 Replacin
16. and servicing Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair To operate properly and safely your wheelchair MUST be cared for just like any other vehicle Routine maintenance will extend the life and efficiency of your wheelchair 41 Safety Inspection Checklist Initial adjustments should be made to suit your personal body structure and preference Thereafter follow these maintenance procedures Inspect Adjust Initially Q Ensure that the wheelchair rolls straight no excessive drag or pull to one side Inspect for loose or missing hardware on frame and crossbraces Inspect for bent frame or crossbraces Check that the wheel locks DO NOT interfere with tires when rolling Check that the wheel lock pivot points are free of wear and looseness Check that the wheel locks are easy to engage Ensure that the wheel locks prevent the wheelchair from moving when engaged Inspect the seat and back for rips and sagging Inspect the seat and back for loose or broken hardware Inspect the back cane hand grips for wear looseness deterioration Ensure seat postioning strap buckle latches Verify hardware that attaches strap to frame is secure and undamaged Replace if necessary Inspect tires for flat spots and wear 00 U D D D D E Check pneumatic tires for proper inflation Invacare Tracer EX2 Wheelchair 24 Part No 1110546 4 SAFETY INSPECTION TROUBLESHOOTING WARNI
17. at Positioning Strap as an additional safeguard for the wheelchair user Remove the bottom back upholstery screw from the wheelchair Position the seat positioning strap half between the back cane and back upholstery Secure the back upholstery and seat positioning strap to the wheelchair with the existing back upholstery screw Ak HM Repeat STEPS 1 3 for the opposite side of the wheelchair Back Cane Back Upholstery Screw Back Upholstery Te Seat Positioning Strap FIGURE 3 Installing the Seat Positioning Strap Invacare Tracer EX2 Wheelchair 62 Part No 1110546 12 12 4 Installing the Wheel Lock Extension Handle A WARNING If the wheelchair is equipped with push to lock wheel locks elevating legrests and wheel lock extension handles the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side otherwise injury or damage may result Interference between the top of the elevating legrest and the wheel lock extension handle causes the wheel lock to disengage Q For this procedure refer to FIGURE 4 l Remove the existing rubber tip from the wheel lock handle Detail A 2 Install the extension handle over the wheel lock handle Detail B Detail Detail Wheel Lock Rubber Tip id Handle Wheel Lock Handle Wheel Lock Handle Wheel Lock Wheel Lock FIGURE 4 Installing the Wheel Lock Extension Handle
18. ate swingaway front rigging assembly outward 3 Lift the swingaway front rigging assembly off the hinge pins Invacare Tracer EX2 Wheelchair 30 Front Rigging Release Lever M Front Rigging Hi o gt d Assembl inge S gt y Footplate Swingaway footrest shown FIGURE Installing Removing Front Riggings Part No 1110546 5 2 Adjusting Footplate Height Spring Button This procedure applies to the swingaway front riggings and swingaway elevating legrest l Remove the front rigging assembly Refer to Installing Removing Front Riggings on page 30 Q Lay the front rigging assembly on a flat surface to simplify this procedure 2 Pull the cam lock lever up to unlocked position The elevating legrest has two sets of release buttons one set above the other Each set will be visible one at a time allowing finer footplate height adjustment 3 Push in the release buttons and reposition the footplate assembly to the desired height 4 Ensure that the release buttons fully protrude from holes on both sides of the front rigging support Rotate cam lock lever down to locked position Repeat this procedure for the other footplate if necessary 7 Reinstall the swingaway front rigging assembly Refer to Installing Removing Front Riggings on page 30 Part No 1110546 3l Adjustment Holes Cam Lock Lever 5 FRONT RIGGINGS Swingaway footrest shown FIGURE 2 Release Button Front
19. available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as owner s manuals service manuals or instruction sheets supplied with this product or optional equipment If you are unable to understand the warnings cautions or instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur A qualified technician MUST perform the initial set up of this wheelchair Also a qualified technician MUST perform all procedures specifically indicated in the manual ACCESSORIES WARNINGS Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE Check all parts for shipping damage and test before using In case of damage DO NOT use Contact Invacare Carrier for further instruction Invacare Tracer EX2 Wheelchair 10 Part No 1110546 Anti tippers 3 SAFETY WARNING Anti tippers are specific to the different seat to floor angles and or seat to floor heights Refer to the chart in this section of the manual for correct usage and adjustment If these requirements cannot be achieved DO NOT use the w
20. ch Seat Depth Seat Upholstery Wheelchair Frame FIGURE 2 Replacing Seat Upholstery Part No 1110546 Adjusting Seat Depth A WARNING 7 SEAT AND BACK The seat depth size position of the front casters size position of the rear wheels use of an anti tipper model as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the seven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician Remove the existing seat upholstery from the wheelchair Refer to page 38 If adjusting the seat depth of the wheelchair the seat upholstery MUST be changed as well Remove the two plug buttons from the ends of the crossbraces that are towards the front of the wheelchair The two plug buttons will be used in the ends of the seat extensions Install the two seat extension tubes into the ends on the crossbraces Line up the rear mounting hole of the seat extension tube with the second mounting hole from the end of the crossbrace Install the two seat extension spacers onto the two seat extension tubes Install the new seat upholstery onto the wheelchair Make sure to line up the mounting holes in the seat extension tubes and seat extension spacers with the new seat upholstery Refer to page 38 Install plug buttons into the ends of the seat extension spacers Part No 1110546 Phillips Screws RA a
21. ch could result in personal injury or property damage See the information below for definitions of the signal words A DANGER Danger indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in property damage or minor injury or both IMPORTANT Indicates a hazardous situation that could result in damage to property if it is not avoided Gives useful tips recommendations and information for efficient trouble free use Part No 1110546 5 Invacare Tracer EX2 Wheelchair GENERAL 1 2 Limited Warranty PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner Coverage under this warranty will end upon any such subsequent sale or other transfer of title to any other person This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants the side frames and cros
22. ducts to our factory without our prior consent LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE THE WARRANTY SHALL NOT APPLY TO NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE OR LIMITATION OF HO
23. e Seat Upholstery Crossbrace Seat Extension Spacer Second Mounting Plug Hole from End Button Rear Mounting Hole w Seat Extension Tube FIGURE 3 Adjusting Seat Depth Invacare Tracer EX2 Wheelchair 7 74 Adjusting the Seat Width Swingaway Front Riggings For this procedure refer to FIGURE 4 FIGURE 5 on page 41 and FIGURE 6 on page 42 When adjusting the seat width of the wheelchair the back and seat upholstery MUST be changed If applicable the headrest pillow and headrest upholstery MUST be changed as well Remove the existing back and seat upholstery from the wheelchair Refer to Replacing Back Upholstery and Replacing Seat Upholstery on page 38 Remove the four button screws and locknuts that secure the two pivot links to the wheelchair frame and crossbraces 3 Remove the two button screws locknuts and crossbrace saddle that secures the bottom of the crossbrace to the wheelchair frame Repeat for other crossbrace 4 Remove the hex screw coved washers washers and locknut that secure the two crossbraces together See Detail Note the orientation of the coved washers washers and locknut for assembling the new crossbraces See Detail B 5 Assemble the two new crossbraces together with the existing hex screw coved washers washers and locknut Securely tighten Refer to Detail B for hardware orientation 6 Determine the correct pivot link and mou
24. eaching as the wheelchair may tip over DO NOT attempt to reach objects if you have pick them up from the floor by reaching down between your knees DO NOT lean over the top of the back upholstery to reach objects behind you as this may cause the wheelchair to tip over Forward Position the front casters so that they are extended as far forward as possible and engage wheel locks Backwards Position wheelchair as close as possible to the desired object Point front casters forward to create the longest possible wheelbase Reach back only as far as your arm will extend without changing your sitting position FIGURE Backwards Invacare Tracer EX2 Wheelchair I8 Part No 1110546 3 SAFETY Coping With Everyday Obstacles Coping with the irritation of everyday obstacles can be alleviated somewhat by learning how to manage your wheelchair Keep in mind your center of gravity to maintain stability and balance Tipping A WARNING DO NOT tip the wheelchair without assistance When lowering the front casters of the wheelchair Do not let the wheelchair drop the last few inches to the ground This could result in injury to the occupant and or damage to the wheelchair When tipping the wheelchair an assistant should grasp the back of the wheelchair on a non removable non detachable part Inform the wheelchair occupant before tipping the wheelchair and remind him her to lean back Be sure the occupant s feet and hands are clear
25. efer to the procedure that is checked gt to maintain the proper 2 gt amp xE stability safety and handling of the wheelchair ir TE Ta b og sl 2 lt YP LI z lt LI CASTER SIZE e vi vi Y vi CASTER POSITION vi e vi vi vi vi WHEEL SIZE vi vi vi Y Y WHEEL POSITION vi vi vi Y vi ANTI TIPPERS vi vi vi vi H vi USER CONDITION vi vi vi vi vi H Weight Limitation WARNING The Tracer EX2 has a weight limitation of 250 pounds 114 kg Part No 1110546 15 Invacare Tracer EX2 Wheelchair 3 SAFETY Weight Training WARNING A Invacare does not recommend the use of its wheelchairs as a weight training apparatus Invacare wheelchairs have not been designed tested as a seat for any kind of weight training If occupant uses said wheelchair as a weight training apparatus Invacare shall not be liable for bodily injury or damage to the wheelchair and the warranty is void Wheel Locks WARNING DO NOT attempt to stop a moving wheelchair with wheel locks Wheel locks are not brakes If the wheelchair is equipped with push to lock wheel locks elevating legrests and wheel lock extension handles the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side otherwise injury or damage may result Interference between the top of the elevating legrest and the wheel lock extension handle causes the wheel lock to disengage Engaging the w
26. eld in place when pushed Part No 1110546 55 Invacare Tracer EX2 Wheelchair 10 ANTI TIPPERS WHEEL LOCKS Bolt and Wheel Lock DETAIL is inch Chg inch Locknut Handle Pneumatic Tires Wheel Lock Shoe Wheel Lock LLL Tire Wheel Lock Shoe Mounting Positions Rear Wheel FIGURE 4 Using Patient Operated Wheel Locks Invacare Tracer EX2 Wheelchair 56 Part No 1110546 l SEAT TO FLOOR 11 Seat to floor WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur The seat to floor height is not adjustable for the Tracer EX2 wheelchair with the fixed frame option FF This procedure applies to the EX2 wheelchair model with swingaway footrests only Changing Seat to Floor Height WARNING The seat depth size position of the front casters size position of the rear wheels use of an anti tipper model as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the seven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician Seat to floor heights have specific positions depending on rear wheel size rear wheel position front caster size and front caster position These adjustments MUST be performed by a qualified technician If changing the seat to fl
27. ement 12 OPTIONS When loading the crutch cane carrier ensure items are securely placed into the base Also ensure that there is no interference with folding the wheelchair the rear wheels or the swing back arms Strap MUST be securely fastened while carrying items NEVER insert or remove items while wheelchair is moving 2 Position the base parallel to the step tube A CAUTION Base should be parallel to step tube to avoid bending spokes when folding the wheelchair 3 Securely tighten the locknut that secures the base to the step tube of the wheelchair 4 Remove the upper back upholstery screw and washer Align the strap with the back upholstery screw mounting hole Reinstall the back upholstery screw and washer and secure the strap to the wheelchair 7 The base cleans easily with any chrome or glass cleaner The strap can be cleaned with mild soap and water Part No 1110546 61 Slide the clamp with the base attached over the end of the step tube of the wheelchair Ensure the base is towards the inside of the wheelchair Step Tube 27 Ss Locknut p 6 FIGURE 2 Installing Crutch and Cane Carrier Invacare Tracer EX2 Wheelchair 12 12 3 Installing the Seat Positioning Strap A WARNING ALWAYS wear your positioning strap Inasmuch as the Seat Positioning Strap is an option on this wheelchair You may order with or without the seat restraint Invacare strongly recommends ordering the Se
28. etail See Detail B FIGURE 5 Adjusting the Seat Width Swingaway Front Riggings Part No 1110546 41 Invacare Tracer EX2 Wheelchair 7 SEAT AND BACK DETAIL B Coved Washers Washer Washer Coved Washer Washer lt Hex Screw Crossbraces DETAIL A Coved Washers Wheelchair Frame Z DETAIL CROSSBRACE HARDWARE STEPS 4 5 N Washer Crossbrace Saddle FIGURE 6 Adjusting the Seat Width Swingaway Front Riggings 42 Part No 1110546 Invacare Tracer EX2 Wheelchair 7 Fixed Frame Removing Lower Mounting Hardware 2 3 4 Remove the existing back and seat upholstery from the wheelchair Refer to Replacing Back Upholstery page 38 Q If adjusting the seat width of the wheelchair back and seat upholstery as well as the crossbraces MUST be replaced Remove the four screws and locknuts that secure the insert tube to the lower wheelchair frame Remove the inserts from the rear of the wheelchair Remove the hex screw and locknut that secure the two existing crossbraces together Removing Upper Mounting Hardware um kHz DETAIL REMOVING UPPER While pushing down on the rear seat guide pull up the front seat guide until the front seat guide releases from the wheelchair frame Pull the crossbrace away from the rear seat guide
29. front and rear until the front and rear armrest release buttons snap into the arm sockets Ensure armrest is locked securely in the arm sockets by gently lifting up If not locked repeat STEPS 1 2 Armrest im D Armrest Release Button Armrest Release Button Rear Arm Socket In FIGURE 2 Removing Installing Armrests Part No 1110546 37 Invacare Tracer EX2 Wheelchair 7 SEAT AND BACK 7 Seat and Back WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 71 Replacing Back Upholstery 1 Remove the eight mounting screws and washers that secure the existing back upholstery to the back canes 2 Remove existing back upholstery from the back canes 3 Securely tighten the new back upholstery to the back canes with the phillips screws and washers 7 2 Replacing Seat Upholstery l Remove the eight phillips screws and washers that secure the existing seat upholstery to the crossbraces 2 Remove the existing seat upholstery from the crossbraces 3 Ensure positioning of seat positioning strap if used Refer to Installing the Seat Positioning Strap page 62 4 Install new seat upholstery by reversing STEPS 1 2 Invacare Tracer EX2 Wheelchair 38 Washers n d eee Mounting Le Screws CU Washers FIGURE I Replacing Back Upholstery Mounting Screw 6 in
30. g Front Casters Invacare Tracer EX2 Wheelchair 50 Part No 1110546 10 ANTI TIPPERS WHEEL LOCKS 10 Anti tippers Wheel Locks A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 10 1 Installing Adjusting Anti Tippers Q For this procedure refer to FIGURE on page 52 A WARNING Anti tippers are specific to the different seat to floor angles and or seat to floor heights Refer to the chart in this section of the manual for correct usage and adjustment If these requirements cannot be achieved DO NOT use the wheelchair Contact a qualified technician If changing the seat to floor height with or without a change to seat to floor angle the correct anti tippers MUST be used to maintain Ze to 2 inch ground clearance If so equipped anti tippers MUST be attached at all times Inasmuch as the anti tippers are an option for 0 or 3 on this wheelchair You may order with or without the anti tippers Invacare strongly recommends ordering the anti tippers as a safeguard for the wheelchair user Anti tippers MUST be fully engaged and release buttons fully protruding out of adjustment holes ALWAYS use anti tippers When outdoors on wet soft ground or on gravel surfaces anti tippers may not provide the same level of protection against tipover Extra caution MUST be observed when traversing such surfaces Ensure both ant
31. hair has been designed to remain upright and stable during normal daily activities as long as you DO NOT move beyond the center of gravity Virtually all activities which involve movement in the wheelchair have an effect on the center of gravity Invacare recommends using seat chest positioning straps for additional safety while involved in activities that shift your weight Part No 1110546 17 Invacare Tracer EX2 Wheelchair 3 SAFETY DO NOT lean forward out of the wheelchair any further than the length of the armrests Make sure the casters are pointing in the forward position whenever you lean forward This can be achieved by advancing the wheelchair and then reversing it in a straight line Many activities require the wheelchair owner to reach bend and transfer in and out of the wheelchair These movements will cause a change to the normal balance the center of gravity and the weight distribution of the wheelchair To determine and establish your particular safety limits practice bending reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair Proper positioning is essential for your safety When reaching leaning or bending forward it is important to use the front casters as a tool to maintain stability and balance Reaching Leaning and Bending WARNING A DO NOT shift your weight or sitting position toward direction you are r
32. heel locks may not prevent the wheelchair from moving on all floor surfaces including those that may be wet or slick ALWAYS exercise caution when transferring into or out of the wheelchair Wheelchair Tie Down Restraints A WARNING Wheelchair users should NOT be transported in vehicles of any kind while in wheelchairs As of this date the Department of Transportation has not approved any tie down systems for transportation of a user while in a wheelchair in a moving vehicle of any type It is Invacare s position that users of wheelchairs should be transferred into appropriate seating in vehicles for transportation and use be made of the restraints made available by the auto industry Invacare cannot and does not recommend any wheelchair transportation systems Invacare Tracer EX2 Wheelchair 16 Part No 1110546 3 SAFETY Wheelchair User A WARNING As a manufacturer of wheelchairs Invacare endeavors to supply a wide variety of wheelchairs to meet many needs of the end user However final selection of the type of wheelchair to be used by an individual rests solely with the user and his her healthcare professional capable of making such a selection 3 2 SafetylHandling of Wheelchairs Safety and handling of the wheelchair require the close attention of the wheelchair user as well as the assistant This manual points out the most common procedures and techniques involved in the safe operation and maintenance of the wheelchair It is i
33. heelchair Contact a qualified technician If changing the seat to floor height with or without a change to seat to floor angle the correct anti tippers MUST be used to maintain a 16 to 2 inch ground clearance If so equipped anti tippers MUST be attached at all times Inasmuch as the anti tippers are an option for 0 or 3 on this wheelchair You may order with or without the anti tippers Invacare strongly recommends ordering the anti tippers as a safeguard for the wheelchair user Anti tippers MUST be fully engaged and release buttons fully protruding out of adjustment holes ALWAYS use anti tippers When outdoors on wet soft ground or on gravel surfaces anti tippers may not provide the same level of protection against tip over Extra caution MUST be observed when traversing such surfaces Ensure both anti tippers are adjusted to the same mounting hole Part No 1110546 II Invacare Tracer EX2 Wheelchair 3 SAFETY General Warnings A WARNING To determine and establish your particular safety limits practice bending reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair Avoid storing or using the wheelchair near open flame or combustible products Serious injury or damage to property may result DO NOT stand on the frame of the wheelchair DO NOT use the footplate as a platform When getting in or out of the wheelchair
34. henever tipping the wheelchair or traversing curbs or other impediments When learning a new assistance technique have an experienced assistant help you before attempting it alone Lifting WARNING DO NOT attempt to lift the wheelchair by any removable detachable parts Lifting by means of any removable detachable parts of the wheelchair may result in injury to the user or damage to the wheelchair Ramps Slopes Inclines and Obstacles WARNING DO NOT traverse climb or go down ramps or slopes greater than 9 DO NOT attempt to move up or down an incline with a water ice or oil film DO NOT attempt to ride over curbs or obstacles Doing so may cause your wheelchair to tip over and cause bodily harm to you or damage to the wheelchair NEVER leave an unoccupied wheelchair on an incline DO NOT attempt to stop the wheelchair while on a sloped surface Part No 1110546 13 Invacare Tracer EX2 Wheelchair 3 SAFETY Repair and Service Information A WARNING Unless otherwise noted all service and adjustment should be performed while the wheelchair is unoccupied After ANY adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may result Seat Positioning Straps WARNING ALWAYS wear your seat positioning strap Inasmuch as the seat positioning strap is an option on this wheelchair you may order with or without the seat positioning strap Invacare
35. i Tippers Al e 2 inch clearance between the bottom of the anti tipper wheels and the ground floor MUST be maintained at all times Place the wheelchair on a flat surface If adjusting anti tippers on recliner models ensure back canes are in the upright position before making 9 adjustments 0 2 the release buttons on the wheeled portion of the anti tipper and slide it up or down to the desired adjustment hole 3 Check to make sure that the release buttons are fully engaged in Release Buttons adjustment holes 4 Ensure both anti tippers are adjusted to the same height Measure the distance between the bottom of the wheels and the gr und floor FIGURE2 Adjusting the Anti Tippers 6 Ifthe distance between the bottom of anti tipper wheels and the ground floor is not to 2 inches repeat steps 2 5 until the distance is l to 2 inches 7 Ifthe l to 2 inch distance cannot be achieved a different model may be required Contact an Invacare dealer or qualified technician Part No 1110546 53 Invacare Tracer EX2 Wheelchair 10 ANTI TIPPERS WHEEL LOCKS 10 2 Using Adjusting Patient Operated Wheel Locks Using Patient Operated Wheel Locks A WARNING DO NOT attempt to stop a moving wheelchair with wheel locks Wheel locks are not brakes If the wheelchair is equipped with push to lock wheel locks elevating legrests and wheel lock exte
36. i tippers are adjusted to the same mounting hole Part No 1110546 5 Invacare Tracer EX2 Wheelchair 10 ANTI TIPPERS WHEEL LOCKS Installing Anti Tippers To ensure the correct model anti tipper is used refer to chart below Measurements for anti tippers are approximate and are taken with extension tube in bottom hole position ANTI TIPPER MEASUREMENTS IN INCHES T Anti Tipper Height Bottom MODEL SEAT TO FLOOR LENGTH HEIGHT MODEL PART NO Position HEIGHT IN INCHES TRACER 17 d to 19 d 13 35 1360 1058836 d 2 Anti Tipper TRACER 21 12 3 9758 1086190 lt q EX2 FF 14 Pee Flat Surface tubing 2 Ensure that the release button of the anti tipper fully protrudes out of the hole in the bottom of the wheelchair frame tubing 3 Place the wheelchair on a flat surface Anti Rattle 4 Measure the distance between the bottom of the anti tipper wheels Anti Tipper and the ground floor Wheels Al d to 2 inch clearance between the bottom of the Anti Tipper anti tipper wheels and the ground floor MUST be maintained at all times Release Buttons Frame Tubing 5 the distance between the bottom of anti tipper wheels and the FIGURE Installing Anti Tippers ground floor is not 5 to 2 inches adjust anti tippers Refer to Adjusting the Anti Tippers on page 53 Invacare Tracer EX2 Wheelchair 52 Part No 1110546 10 ANTI TIPPERS WHEEL LOCKS Adjusting the Ant
37. ight WARNING Make sure the height adjustment lever is in the locked position before using the wheelchair l Unlock the armrest by flipping the height adjustment lever on the top front of the armrest to the up horizontal position Locked Vertical Height Adjustment Lever 2 Adjust the armrest to one of five positions Armrest Q Height adjustment lever MUST be in the unlocked position when placing armrest into the arm assembly 3 Lock the armrest by pressing the height adjustment lever into the a down vertical position when the desired armrest height is achieved 33 4 Repeat STEPS 1 3 for the other armrest SN Unlocked Horizontal FIGURE 1 Adjusting Armrest Height Invacare Tracer EX2 Wheelchair 36 Part No 1110546 6 2 Removing Installing Armrests A WARNING 6 ARMS Make sure the height adjustment lever is in the locked position before using the wheelchair Removing Armrest Push down on armrest to ensure it is fully seated in front and rear sockets STEP prevents the release buttons from hanging up on the sockets during removal Press in the armrest release button at the front and rear of the armrest 2 3 While pressing in the armrest release buttons remove the armrest from the arm sockets by pulling straight up Installing Armrest l 2 3 Position the armrest just above the front and rear arm sockets Push arm down evenly at the
38. ld be pulled up and over the curb DO NOT return the front casters to the ground until the wheelchair has been pulled backward far enough for the front casters to clear the edge of the curb Roll the wheelchair backward and slowly lower the wheelchair in one continuous movement Turn the anti tippers so the anti tip wheels are facing down FIGURE 3 Method 2 Wheelchair Without Step Tubes Stairways WARNING Extreme caution is advised when it is necessary to move an occupied or unoccupied wheelchair up or down the stairs Invacare recommends that if possible the user be removed from the wheelchair prior to moving Invacare recommends using two assistants and making thorough preparations Make sure to use only secure non detachable parts for hand held supports Follow this procedure for moving the wheelchair between floors when an elevator is not available Moving Up Stairs If necessary rotate the anti tippers so the wheels are facing up 2 One assistant positioned behind the wheelchair securely grasps a non removable non detachable part of the wheelchair for leverage and tilts the wheelchair back to the balance point After the wheelchair has been tilted back to the balance point the assistant behind the wheelchair backs the wheelchair up against the first step 4 second assistant positioned in the front of the wheelchair with a firm hold on a non detachable part of the framework lifts the wheelchair up and on
39. move a wheelchair between floors Serious bodily injury may occur Transferring To and From Other Seats A WARNING Before attempting to transfer in or out of the wheelchair every precaution should be taken to reduce the gap distance Turn both casters parallel to the object you are transferring onto Also be certain the wheel locks are engaged to help prevent the wheels from moving Part No 1110546 21 Invacare Tracer EX2 Wheelchair 3 SAFETY A CAUTION When transferring position yourself as far back as possible in the seat This will help prevent damaged upholstery and the possibility of the wheelchair tipping forward This activity may be performed independently provided you have adequate mobility and upper body strength Position the wheelchair as close as possible alongside the seat to which you are transferring with the front casters pointing parallel to it Remove or flip up the armrest Engage wheel locks Swing away or remove front rigging Shift body weight into seat with transfer During independent transfer little or no seat platform will be beneath FIGURE 5 Transferring To and From Other Seats you Use a transfer board if at all possible Unfolding and Folding Wheelchair WARNING A ALWAYS keep hands and fingers clear of moving parts to avoid injury DO place hand or fingers on the underside of the seat frame rail when opening or closing the wheelchair DO NOT sit or transfer into the wheelchair unles
40. mportant to practice and master these safe techniques until you are comfortable in maneuvering around the frequently encountered architectural barriers Use this information only as a basic guide The techniques that are discussed on the following pages have been used successfully by many Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual Invacare recognizes and encourages each individual to try what works best for him her in overcoming architectural obstacles that they may encounter However all warnings and cautions given in this manual MUST be heeded Techniques in this manual are a starting point for the new wheelchair user and assistant with safety as the most important consideration for all Stability and Balance A WARNING Be aware that carrying heavy objects on your lap while occupying the wheelchair may adversely affect the stability of the wheelchair resulting in serious bodily injury to the user damage to the wheelchair and surrounding property This wheelchair has been designed to accommodate one individual If more than one individual occupies the wheelchair this may adversely affect the stability of the wheelchair resulting in serious bodily injury to the user and passenger and damage to the wheelchair and surrounding property To assure stability and proper operation of your wheelchair you MUST maintain proper balance at all times Your wheelc
41. nsion handles the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side otherwise injury or damage may result Interference between the top of the elevating legrest and the wheel lock extension handle may cause the wheel lock to disengage Position wheelchair on a flat level surface to perform this procedure Ensure the wheelchair is not moving before engaging the wheel locks Detail A for instructions Push to Lock Refer to Detail for instructions Pull to Lock 2 Disengage the wheel locks by reversing the directions in STEP Detail A Push To Lock Detail B Pull To Lock Push wheel lock handle away from 8 the tire to disengage wheel lock Pull wheel lock Bush wheel lock Pull wheel lock handle toward the handle backward Da 27S handle forward away tire to disengage Me Li lt from the tire to wheel lock engage wheel lock engage wheel lock Unlocked Position Unlocked Position Wheel Lock Wheel Lock Locked Position Locked Position FIGURE 3 Using Patient Operated Wheel Locks Invacare Tracer EX2 Wheelchair 54 Part No 1110546 10 ANTI TIPPERS WHEEL LOCKS Adjusting Patient Operated Wheel Locks 10 lI WARNING DO NOT attempt to stop a moving wheelchair with wheel locks Wheel locks are not brakes If wheel locks do not hold the occupied wheelchair in place con
42. nsure wheel bearings are clean and free of moisture Invacare Tracer EX2 Wheelchair 26 Part No 1110546 a a a a 42 Troubleshooting Inspect casters for cracks and wear Ensure that casters are free of debris Clean upholstery and armrests with mild soap and water Check that all labels are present and legible Replace if necessary 4 SAFETY INSPECTION TROUBLESHOOTING Chair Chair 3 Sluggish Turnor Casters Squeaks and Looseness Solutions Veers Wheels Performance Flutter Rattles Chair Right Left Check tires for correct and x x x x equal pressure x x x x Check for loose nuts and bolts x x x Check caster headtube angle Check that rear wheels are equally spaced away from seat x x frame Part No 1110546 27 Invacare Tracer EX2 Wheelchair 4 SAFETY INSPECTION TROUBLESHOOTING 4 3 Maintenance Maintenance Safety Precautions A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or damage may result Replace any labels that are missing worn or torn Refer to Label Locations on page 7 for a listing of the labels and their locations A CAUTION DO NOT overtighten hardware attaching to the frame This could cause damage to the frame tubing Suggested Maintenance Procedures Before using your wheelchair make sure all nuts and bolts are tight 2 Check all parts for damage or wear
43. nt pin and detent balls of the quick release axles are fully released and protruding out of the hole before operating the wheelchair Keep detent balls clean 5 Reinstall rear wheel to the wheelchair Refer to Removing Installing Rear Wheels on page 44 6 Repeat STEPS 1 5 for the opposite rear wheel if necessary FIGURE 4 Replacing Rear Wheel Handrim Invacare Tracer EX2 Wheelchair 48 Part No 1110546 9 Front Casters 9 1 Soy Dn WARNING 9 FRONT CASTERS After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur Installing Replacing Front Casters Forks WARNING Make sure both fork caster assemblies are the same size before using the wheelchair otherwise injury may occur Q This procedure can be performed if replacing the exact same size front caster Remove the dust cover Remove the locknut and nylon washer that secures the fork to the caster headtube Drop the fork assembly out of the caster headtube If caster tire tube replacement is desired refer to Replacing Front Casters on page 50 Slide the new fork assembly into the caster headtube Reassemble by reversing STEPS 1 3 Repeat STEPS 1 6 for the opposite fork assembly Adjust the forks Refer to Adjusting Forks on page 50 Part No 1110546 49 e Dust Cover a Locknut m Nylon Washer Caster Headtube Fork Assembly FIGURE Inst
44. nting hole to use with the desired seat width 7 Secure the pivot links to the crossbraces and wheelchair frame with the four button screws and locknuts Securely tighten Position crossbrace saddle on wheelchair frame using the washer on the underside of the wheelchair frame as a reference See Detail for proper positioning of the crossbrace saddle 8 Reinstall the two button screws locknuts and crossbrace saddle that secures the bottom of the new crossbrace to the wheelchair frame Refer to Detail B for hardware orientation Repeat for opposite crossbrace Securely tighten 9 Install the new back and seat upholstery onto the wheelchair Refer to Replacing Back Upholstery page 38 and Replacing Seat Upholstery on page 38 Invacare Tracer EX2 Wheelchair 40 SEAT WIDTH PIVOT LINK 16 INCH 18 inch 18 INCH inc pud J mE Zi Ns DL uiae DO NOT USE 20 INCH 20 inch 22 INCH Ne We DO NOT USE FIGURE 4 Adjusting the Seat Width Swingaway Front Riggings Part No 1110546 7 Crossbrace STEPS 4 5 Km Button Screw STEPS 2 7 Pivot Link STEPS 2 7 Locknut Locknut STEPS 2 7 STEPS 2 7 Button Screw STEPS 2 7 e os 6 2 Button Screw addle STEPS 38 ton Screw STEPS 3 8 Tw 5 2 7 Locknu Crossbrace Saddle heelchair STEPS 3 8 STEPS 3 8 Frame See D
45. of all wheels and or pinch points After mastering the techniques of tipping the wheelchair use one of the following methods to tackle curbs short stairs etc Method Wheelchair With Step Tubes Place foot on the step tube and begin to tilt the wheelchair toward you Apply a continuous downward motion until the balance point is achieved and the front casters clear the curb At this point the assistant will feel SRS a difference in the weight distribution Roll the wheelchair forward and slowly lower the front of the wheelchair f one continuous movement onto the sidewalk Push the wheelchair d forward until the rear wheels roll up and over the curb WS Step Tube FIGURE 2 Method Wheelchair With Step Tubes Method 2 Wheelchair Without Step Tubes This method requires two assistants The second assistant should be positioned at the front of the wheelchair lifting upward on a non removable non detachable part of the wheelchair frame when lifting the wheelchair and stabilizing the wheelchair when the wheelchair is being lowered to the ground Part No 1110546 19 Invacare Tracer EX2 Wheelchair 3 SAFETY The first assistant should stand the sidewalk and turn the wheelchair so that the rear wheels are against the curb Turn the anti tippers so the anti tip wheels are pointing up The wheelchair should be tilted back to the balance point and in one continuous upward movement the rear wheels shou
46. oor height the correct anti tippers MUST be ordered to maintain m to 2 inch ground clearance For this procedure refer to FIGURE on page 58 Refer to the following chart in FIGURE to determine mounting positions for front casters forks and rear wheels for the desired obtainable seat to floor height Remove the rear wheels from the wheelchair Refer to on page 44 If necessary replace the front casters and forks with the casters and forks indicated in the chart Refer to Replacing Front Casters on page 50 Reinstall the rear wheels onto the wheelchair in the mounting position indicated in the chart Refer to on page 44 Adjust anti tippers according to new seat to floor height Refer to Installing Adjusting Anti Tippers on page 51 Part No 1110546 57 Invacare Tracer EX2 Wheelchair II SEAT TO FLOOR 8 INCH FRONT CASTERS SEAT TO FLOOR HEIGHT FRONT CASTER REAR WHEEL SIZE REAR WHEEL IN INCHES MOUNTING POSITION MOUNTING POSITION 17 24 inch 19 Bottom 24 inch Bottom DETAIL A DETAIL B 8 INCH FORK REAR WHEEL MOUNTING POSITIONS MOUNTING POSITIONS ADULT HEMI FRAME STYLE Top Top Middle Bottom 3 Bottom FIGURE Changing Seat to Floor Height Invacare Tracer EX2 Wheelchair 58 Part No 1110546 12 Options WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 12 1 In
47. pholstery Seat Upholstery Rear Wheel Wheelchair Frame Rear Wheel Axle Front Caster Handrim Wheel Lock Invacare Tracer EX2 Wheelchair 8 Part No 1110546 2 2 Typical Product Parameters 2 OVERVIEW Tracer EX2 Overall Width Permanent Arm 231 4 251 4 27 inches Removable Arm 24114 261 4 281 4 inches Overall Depth with Front Riggings 3 17 8 inches Seat Width 16 18 or 20 inches Seat Depth 16 inches Seat to Floor Heights with 24 inch Wheels Adult SA Frame ol inches Adult FF Frame 21 inch Hemi SA Frame E 17 5 inches Back Height 16 inches Weight Approx Permanent Arm Removable Arm 36 pounds SA Frame 37 pounds FF Frame 36 pounds SA Frame Shipping Weight Approx Permanent Arm Removable Arm 451 pounds SA Frame 46 15 pounds FF Frame 45 s pounds SA Frame Weight Limit 250 pounds 114 kg The seat to floor heights are based on urethane tires These heights can vary inch due to tire wear and manufacturing tolerances Weights based on 18 inch wide wheelchair without front riggings Weights will vary depending on how the wheelchair is equipped Part No 1110546 9 Invacare Tracer EX2 Wheelchair 3 SAFETY 3 Safety The safety section contains important information for the safe operation and use of this product 3 General Guidelines A WARNING DO NOT use this product or any
48. rear wheel 4 reinstall the rear wheel onto the wheelchair reverse STEPS 1 3 Q Make sure axle spacer is between rear wheel and wheelchair frame if wheelchair is equipped with conventional arms Part No 1110546 45 Invacare Tracer EX2 Wheelchair 8 REAR WHEELS WARNING Make sure the detent pin and detent balls of the quick release axle are fully released before operating the wheelchair The detent balls MUST be protruding past the inside of the rear wheel axle bushing for a positive lock Detail A Keep detent balls clean Invacare recommends inserting quick release axles with the detent pin to the inside of the wheelchair to prevent accidental release during contact activities 5 Ifthe detent balls are not protruding past the inside of the axle bushing or there is too much side to side movement of the rear wheel assembly refer to Adjusting Quick Release Axle on page 47 DETAIL A Axle Bushing Detent Axle Mounting Positions t BALLS petent Ball Pin Zug AND PIN Conventional Arms Only JONES Wheelchair Frame Inside of Quick Release Rear Wheel Wheelchair om eser Axle Outside of E i Wheelchair FIGURE 2 Removing Installing Rear Wheels Quick Release Axles Quick Release Axle Invacare Tracer EX2 Wheelchair 46 Part No 1110546 8 REAR WHEELS 83 Adjusting Quick Release Axle I
49. s it is fully open and the seat frame rails are fully seated into the side frame H blocks Invacare Tracer EX2 Wheelchair 22 Part No 1110546 Unfolding Tilt the wheelchair toward you raising the opposite wheel and caster off the ground floor Place your hand on the top of the seat rail closest to you where the seat upholstery is attached Point your fingers and thumb to the inside of the wheelchair Press downward on the top of the seat rail until the wheelchair is fully open and the seat rails are fully seated in the H blocks Engage both wheel locks open the footrest legrest for clearance and transfer into the wheelchair Refer to Transferring To and From Other Seats on page 21 Folding Hammock or Sling Seat Models 2 3 Swing footrest legrest in locked position to front of wheelchair Pivot footplates upward to vertical position With both hands grasp the middle of the seat upholstery at the front and back edge and lift up Continue to close the wheelchair by grasping the armrest furthest from you and pulling the armrest towards you Part No 1110546 3 SAFETY Press DOWN on Seat Rail FIGURE 6 Unfolding and Folding Wheelchair FIGURE 7 Folding Hammock or Sling Seat Models 23 Invacare Tracer EX2 Wheelchair 4 SAFETY INSPECTION TROUBLESHOOTING 4 Safety Inspection Troubleshooting Every six months or as necessary take your wheelchair to a qualified technician for a thorough inspection
50. s members of this product when purchased new and unused to be free from defects in materials and workmanship for a period of five 5 years from the date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty Invacare warrants the upholstered materials seat back and armrests of the arm assembly and remaining components of this product when purchased new and unused to be free from defects in materials and workmanship for a period of thirteen 13 months from date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty If within such warranty periods any such product shall be proven to be defective such product shall be repaired or replaced at Invacare s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address at the bottom of this page Provide dealer s name address the product model number date of purchase indicate nature of the defect and if the product is serialized indicate the serial number Do not return pro
51. s or deterioration is found Replacing Repairing Rear Wheel Tire Tube WARNING Replacement of solid urethane tires is not recommended If the solid urethane tire needs repaired Invacare recommends replacing the complete wheel assembly Replacing Repairing Caster Tire Tube A WARNING Replacement of solid rubber tires is not recommended If the solid rubber tires need replaced Invacare recommends replacing complete caster assembly Part No 1110546 29 Invacare Tracer EX2 Wheelchair 5 FRONT RIGGINGS 5 Front Riggings WARNING A After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 5 1 Installing Removing Front Riggings Installing Turn the front rigging assembly to the side 2 Install the hinge plates on the front rigging assembly onto the hinge pins on the wheelchair frame When performing STEP 3 it may be necessary to pull release lever toward front of chair to assist the front rigging to lock in place 3 Push the front rigging assembly towards the inside of the wheelchair until it locks into place Q The footplate will be on the inside of the wheelchair when locked in place 4 Repeat this procedure for the other front rigging assembly 5 To release the front rigging push the front rigging release lever inward rotate front rigging outward Removing Push the front rigging release lever inward 2 Rot
52. stalling Amputee Bracket Q For this procedure refer to FIGURE on page 60 12 OPTIONS Refer to the following chart or FIGURE to determine the mounting position of the amputee bracket SEAT TO FLOOR BRACKET AXLE SPACER POSI SIDE OF BRACKET MOUNTING POSITION TION ON BRACKET WHEELCHAIR ON WHEELCHAIR ADULT A DOWN RIGHT TOP ADULT B DOWN LEFT TOP HEMI B UP RIGHT BOTTOM HEMI A UP LEFT BOTTOM Q A and B are stamped on the sides of the amputee bracket 2 Install the amputee bracket the wheelchair frame to the position determined in STEP I Make sure the axle spacer is pointing towards the outside of the wheelchair 3 Install the two hex screws and locknuts that secure the amputee bracket to the wheelchair 4 Install the rear wheels onto the wheelchair Removing Installing Rear Wheels on page 44 Part No 1110546 59 Invacare Tracer EX2 Wheelchair 12 Bracket Adult Right Axle Spacer Toward Outside of Wheelchair Hemi Left Invacare Tracer EX2 Wheelchair Locknuts Rear View of Amputee Bracket N Hex Screws Eo FIGURE Installing Amputee Bracket 60 Bracket B Adult Left Axle Spacer Toward Outside of Wheelchair Hemi Right Part No 1110546 12 2 Installing Crutch and Cane Carrier A WARNING Check base weekly to ensure proper plac
53. stery Adjusting Seat Depth n ttr EAR Adjusting the Seat Width estes REAR WHEELS Replacing Repairing Rear Wheel Tree Part No 1110546 CONTENTS Invacare Tracer EX2 Wheelchair CONTENTS Remioving Installinig Rear Wheels u u u u u aaa aaaea a A E Ea E Dee snn EES 44 Adjusting Quick Release Axle d Replacing Rear Wheel Flandrim e ee e tt RR cR Dp eo assed 48 FRONT CASTERS 49 Installing Replacing Front Casters Forks 49 Adjusting Forks 50 EEN deu 50 ANTI TIPPERS WHEEL LOCKS 51 nstalling Adjusting AntieTippersuu D 51 Using Adjusting Patient Operated Wheel Locke 54 SEAT TO FLOOR 57 Changing Seat to Floor Height ua reete darte i decente terere 57 OPTIONS 59 Installing Amputee Brackets REC es 59 Installing Grutch and Gane Carrier rn eu e E e DEIN NOH VH asia NS DER rin epe dyes obest eee et 6l Installing the Seat Positioning Strap tre t tite e RE Ree ORE RUE UAR EU E Dn e Ma ED Hee ER EB 62 Installing the Wheel Lock Extension Handlen 63 Invacare Tracer EX2 Wheelchair 4 Part No 1110546 GENERAL General 1 1 Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices whi
54. t Bolt In Place Footplates Detail i From the outside of the swingaway front rigging insert the threaded rivet through both the front rigging support and the footplate assembly ii From the inside of the swingaway front rigging insert the button head screw through the appropriate adjustment hole and thread into the threaded rivet iii Using a screwdriver to hold the threaded rivet in position securely tighten the button head screw Torque to 32 in Ibs Rotate cam lock lever down to locked position Invacare Tracer EX2 Wheelchair 34 Part No 1110546 5 FRONT RIGGINGS DETAIL A DETAIL B Footplates with Spring Buttons Bolt in Place Footplates Front Rigging Support Front Rigging Support Button Head Screw Front Rigging Support Threaded 0 Rivet A Footplate Assembly Adjustment Adjustment i Inside of Swingaway Holes Front Rigging Cam Lock ever Footplate Assembly Footplate Cam Lock Lever h Assembly Outside of Swingaway Front Rigging Cam Lock Mounting Screw Spacer Heel Loop Slide Tube Footplate Assembly Locknut Footplate FIGURE 6 Replacing Heel Loop Part No 1110546 35 Invacare Tracer EX2 Wheelchair 6 5 6 Arms A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 6 Adjusting Armrest He
55. tact a qualified technician otherwise injury or damage may occur Q If wheels are pneumatic before adjusting the wheel lock assemblies ensure that the tires are inflated to the recommended psi on the side wall of the tire Position wheelchair on a flat level surface to perform this procedure Ensure the wheel lock is in the open unlocked position Loosen the bolt and locknut that secure the wheel lock assembly to the wheelchair frame Reposition the wheel lock so that when engaged the wheel lock shoe embeds the tire inch Chg inch for pneumatic tires and holds the occupied wheelchair in place when pushed Securely tighten the bolt and locknut attaching the wheel lock to the wheelchair frame Engage the wheel lock Measure the distance the wheel lock is embedded into the tire as shown in Detail A Q wheel lock adjustment should embed the wheel lock shoe at least Ue inch ene inch for pneumatic tires into the tire when engaged Repeat the STEPS 1 6 until the wheel lock shoe embeds the tire d Clic inch for pneumatic tires and holds the wheelchair in place when pushed Repeat STEPS 1 7 for the opposite wheel lock If the measurement of 1 8 inch 3 16 inch for other tires cannot be achieved remove the bolt and locknut that secure the wheel lock to the wheelchair frame and mount the wheel lock in the remaining mounting position Repeat STEPS 1 8 Engage both wheel locks and ensure the occupied wheelchair is h
56. to the next stair above and steadies the wheelchair as the assistant behind the wheelchair places one foot on the next stair above and repeats process 5 wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway Invacare Tracer EX2 Wheelchair 20 Part No 1110546 6 3 SAFETY If necessary rotate the anti tippers so the wheels are facing down Moving Down Stairs 2 6 If necessary rotate the anti tippers so the wheels are facing up One assistant positioned behind the wheelchair securely grasps a non removable non detachable part of the wheelchair for leverage and tilts the wheelchair back to the balance point After the wheelchair has been tilted back to the balance point the assistant behind the wheelchair rolls the wheelchair up to the edge of the first step The second assistant positioned in the front of the wheelchair with a firm hold on a non detachable part of the framework lowers the wheelchair down and on to the next stair below and steadies the wheelchair as the assistant in the rear places one foot on the next stair below and repeats process The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from stairway If necessary rotate the anti tippers so the wheels are facing down FIGURE 4 Stairways Escalators A WARNING DO NOT use an escalator to
Download Pdf Manuals
Related Search