OPERATING INSTRUCTIONS
Contents
1. www fineprint cn CONNECTING THE TOOL TO AN AIR SUPPLY 1 Determine if the tool needs oil and if necessary place two drops of oil in the AIR PLUG 72 as shown in Figure 2 If you are using an automatic in line oiler check and add oil ifnecessary 2 Turn the compressor on and set the regulator to the proper pressure for the size and type of fastener being used 3 Connect the tool to the air supply see Setup for air supply connection recommendations LOADING THE FASTENERS 1 Depress the LOCK 60 to release the MOVABLE MAGAZINE 51 and pull the magazine out fully as shown in Figure 3 2 Place a full clip of the specified type and size fasteners on the FIXED MAGAZINE 54 up to 100 fasteners may be loaded in the magazine 3 Push the MOVABLE MAGAZINE ASSEMBLY forward until it is locked FIXED MAGAZINE UNIT MOVABLE MAGAZINE UNIT Figure 3 OPERATING THE TOOL Test the driving depth in a sample piece of wood before using If the fasteners are being driven too far or not far enough adjust the regulator to provide less air pressure or more air pressure 1 Connect the tool to the air supply Make sure the air pressure is in correct range denoted in section of SPECIFICATIONS 2 Load fastener as above the direction given in the section called LOAD THE FASTENER 3 Hold the Body 23 and press the Drive guide 44 to work surface be sure the tool is straight and then gently depress the Trigger 38 t2. 2 Clean drive channel of front 4 USE SAFETY GLASSES Safety glasses should conform to ANSI Z87 1 specifications Before operating plate wear safety glasses against flying debris from the front and side Safety glasses should be worn when loading e ac a hose ad compressor operating unloading or servicing this tool ings 4 Worn or dry O ring on piston 4 ii O ring or lubricate 5 USE EAR PROTECTION The working area may be exposed to high noise levels that can lead to hearing 5 Cylinder cap seal leaking 5 Replace seal damage 6 NEVER USE OXYGEN COMBUSTIBLE GASES BOTTLED GASES OR HIGH PRESSURE Fasteners are jammed 1 Joint guider is worn 1 Replace joint guider COMPRESSED GAS AS A POWER SOURCE FOR THIS TOOL The tool may explode and cause 2 Fasteners are wrong size or damaged 2 Use the recommended and seriousinjury send fastenerls 7 DRESS SAFELY Protective gloves and nonskid footwear or safety shoes are recommended when working 3 Magazine or front plate screws are loose ri c Li pr with and operating this tool Don t wear loose clothing or jewelry They can get caught in moving parts Also 4 Blade in piston assembly is damaged Gii p i wear a protective hair covering to prevent long hair from getting caught in the tool Tool will not drive 1 Worn blade in piston assembly 1 Replace piston assembly 8 DONOTFIRE INTO HARD MATERIALS Do not attempt to shoot toward hard or brittle material such down tight 2 Lack of power
3. 10023321 CONTENTS SPECIFICATIONS SAFETY WARNINGS amp CAUTIONS UNPACKING SETTING CONNECTING THE TOOL TO ANAIR SUPPLY LOADING THE FASTENERS OPERATING THE TOOL REGULAR MAINTENANCE TROUBLE SHOOTING EXPLODED VIEW DRAWING PARTS LIST PDF SAPAEH pdfFactory Pro UGUBARKGUE www fineprint cn EXPLODED VIEW DRAWING E Pl xu om dA llo s Dg T LN T m Bu E E inn de Re UE 4 E um lu A ae TROUBLE SHOOTING READ ALL INSTRUCTIONS BEFORE OPERATING THE TOOL STOP USING THE TOOL IMMEDIATELY IF ANY OF THE FOLLOWING PROBLEMS OCCUR SERIOUS PERSONAL INJURY COULD OCCUR ANY REPAIRS OR REPLACE MENTS MUST BE DONE BY A QUALIFIED PERSON OR AN AUTHORIZED SERVICE CENTER SUMMARY ONLY You will need the instructions for the safety warning and cautions assembly instructions operating and maintain ing procedures exploded view drawing and parts list Keep your invoice with these instructions Keep the instruc tions and invoice in a safe and dry place for future reference PROBLEM PROBLEM CAUSE SOLUTION Air leaking at 1 O ring in trigger valve is damaged 1 Check and replace O ring SPECIFI
4. 2 Adjust to adequate air as concrete steel or tile pressure P 3 Slow cycling and loss of power 3 Check cylinder ap sping for 9 WHEN OPERATING TOOL keep the proper footing and balance to avoid damage resulting from losing balance broken coils or reduced length Check if exhaust port of cylin 10 CHECK DAMAGED PARTS Before using tool carefully check if there is any part damaged der cap is restricted 11 REPLACE PARTS AND ACCESSORIES Only allow the use of the same replacement parts while servicing Approved accessories and replacement parts are available 12 KEEP ALERT Watch what you are doing Use common sense Do not operate any tool when you are tired 4 1 PDF AEH pdfFactory Pro RARA GE www fineprint cn PDF 13 STORE THE TOOL When not in use tool should be cleaned fully assembled and then stored in a dry location to reduce rust For safety keep out of reach of children 14 OUTDOOR EXTENSION CORDS When air compressor is used outdoors use only rounded jacket ex tension cords intended for outside use See manufacturer s manual for the AWG required for the compressor s amperage draw 15 PAY ATTENTION TO AIR HOSE AND THEIR CONNECTIONS Don t trip over hoses Make sure all connections are tight 16 AFTER LOADING THE FASTENERS never point the tool at yourself or bystanders 17 USE THE CORRECT AIR CONNECTOR The connector on the tool must not hold pressure when the air supply is disconnected I
5. CATIONS Trigger area 2 Trigger valve head is damaged 2 Check and replace trigger 3 Trigger valve stem seal or O ringisdam 3 Check and replace trigger F 7 aged valve stem seal or O ring Minimum Operating Air Pressure 60 PSI Airleaking between Damaged bumper Check and replace bumper Maximum Operating Air Pressure 100 PSI body and drive guider Stapler Length Range 3 8 1 4 Air leaking between 1 Screw loose 1 Tighten screws Stapler Size 19 Gauge body and cylinder cap 2 Damaged gasket 2 Check and replace gasket Stapler Capacity 100 AirInlet 1 4 NPT Blade driving fastener 1 Worn bumper 1 Replace bumper Air Consumption 3 8 CFM too deeply 2 Air pressure is too high 2 Adjust the air pressure Tool Weight 3 59 Ibs Runs slowly or has 1 Insufficient oil 1 Lubricate as instructed power loss 2 Insufficient air supply 2 Check air supply SAFETY WARNINGS amp CAUTIONS i spring in di cap iva E is i 1 KEEP WORKING AREA CLEAN Cluttered areas invite injuries t port E t TEE ce eee 2 DON T ALLOW CHILDREN AT THE WORKING AREA Don t let them handle the tool 3 DONOTOPERATE THIS TOOLIF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS Read Tool skips a fastener 1 Worn bumper or damaged spring 53 1 Replace bumper or pusher warning label on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there spring is any doubt do not attempt to operate 2 Dirt in drive guider
6. PDF 4 pdfFactory Pro amp PARTS LIST Refer to the Exploded View Drawing for the location of parts listed below _pescrieron mm pescremon scaEwwen 37 was sose 38 TRIGGERSSEMBY EXHAUSTCO MER 3 WASHER SCREW M5 20 WASHER SPRING WASHER 5 OBLIQUEBLOCK ae 38 39 a CYLINDERCAP SCREW M4 25 GASKET DRIVEGUIDE SPRING 45 LIMITEDBLICK era s TRIGGERPIN SCREW M4 16 VALVESEAT SLIDEPLATE 10 O RING 15 7 2 BUSHING SCREW DRIVEGUIDE SPRING PIN 2 5 12 MOVABLEMAGAZINE O RING 38 8 3 1 VALVE 1 B 1 12 3 14 STOPPEDWASHER 15 COLLAR FEEDERSHOE O RING 50 5 2 5 SPRING O RING28 3 3 FIXEDMAGAZING PISTONASSEMBLY NUTM4 CYLINDER 56 MAGAZINGPLATE O RING 36 3 2 5 SCREW M4 6 O RING 35 3 2 5 SCREW M4 14 BUMPER SPRING PIN BOY so mw ovium 0 0 0 a rox 8 5 sarecupe sovune seernes 6 wmr 5 27 sartRACKET 64 sroPrEpscREW 28 29 SEAL 66 NUT O RING 15 1 9 68 SOFTGRIPSLEEVE TRIGGERVALVEGUIDE o ce ORINGSSLS 70 ENDCAP 000 00 SPRING 71 WASHER4 TRIGGERVALVESTEM 72 AIRPLUG SPRING O RING 33 5 3 5 7 8 9 42 43 44 47 48 49 50 51 52 53 54 55 57 58 59 2 www fineprint cn OPERATING INSTRUCTIONS 18G FIOORING STAPLER MODEL
7. fthe wrong fitting is used the tool can be charged with air after being disconnected and still be able to drive a fastener 18 WHEN CONNECTING THE AIR The tool may possibly fire the fasteners as soon as you plug it in to air hose Therefore remove all the fasteners before connecting to the air 19 DO NOT DEPRESS THE TRIGGER WHEN LOADING 20 IF THE FASTENERS ARE JAMMED Disconnect the tool from the air and remove the jammed fasteners WARNING The warning caution and instructions explained in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that COM MON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO THIS PRODUCT BUT MUST BE SUPPLIED BY THE OPERATOR UNPACKING When unpacking check and make sure that all the accessories are included If anyone is missed or broken please call seller for help Refer to the follow lists Stapler S3 Hex Key S4 Hex Key AirTool Oil Operatinginstruction Teflon Tape SETTING Your air tool is fully assembled when you receive it Before using it attach the air line and desired air system accessories See Figure 1 for the recommended accessories and connection order Be sure the air hose is depressur ized when installing or removing adapters to the air line QUICK STAPLER CONNECTOR OILER FILTER AIR SUPPLY E AIR HOSE REGULATOR Figure 1 2 4 pdfFactory Pro amp
8. o drive the fastener 4 Lift the tool off the work surface REGULAR MAINTENANCE 1 Frequent but not excessive lubrication is required for best performance Oil added through the airline connection will lubricate internal parts An automatic airline oilier is recommended but oil may be added manually before every operation or after about 1 hour of continuous use Only a few drops of oil at a time are necessary Too much oil will collect inside the tool and be blown out during the exhaust cycle ONLY USE PNEUMATIC TOOL OIL Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seal in the tool 2 Use a small amount of oil on all moving surface and pivots 3 Dirt and water in the air supply are major causes of pneumatic tool wear Use a filter oiler for better perfor mance and longer life The filter must have adequate flow capacity for the specific application Consult the manufacturer s instructions for proper maintenance of your filter 4 Keep tools clean for better and safer performance Use nonflammable cleaning solutions CAUTION Such solutions may damage O ring and other tool parts only if necessary DO NOT SOAK 3
Download Pdf Manuals
Related Search