TT31 Transponder Installation Manual
Contents
1. Trig Avionics Limited TT31 Transponder Installation Manual 00455 00 12 ADS B Compliance 27 March 2012 Issue AM TT31 transponders with software version 3 1 and above include support for Extended Squitter ADS B out which is compliant with DO 260B The TT31 is a BIS ADS B transmitter 12 1 ADS B Parameters Supported The following table lists the ADS B parameters that are transmitted by the TT31 transponder when connected to an appropriate GPS receiver Parameter SPI Barometric Altitude Quality Indicator NIC Latitude Airborne Position Longitude Quality Indicator NIC Latitude Surface Position Longitude Surface Ground Speed Surface Ground Track Aircraft Identification Airborne Ground Velocity Geometric to Barometric Altitude Difference Geometric Vertical Speed Squawk Code Emergency Status BDS Register 0 5 Emergency Indicator SS Se 0 5 0 5 0 5 0 5 gt gt 6 1 Quality Indicator NACp NACv and GVA Quality Indicator SIL and SDA 6 5 6 5 6 5 5 Surface Length Width Surface Antenna Offset gs 6 6 5 In all cases uncompensated latency due to the transponder is less than 10 milliseconds Analysis of the system latency should add this to the latency of the GPS system and the transmission time of the position data from the GPS to the transponder to determine the overall latency 12 2 FAA 91 227 Compliance The TT31 transponder can be connected to the fol2. 9 Suppressin 10 standby Swich lu isvoce e ussvpe A Oroua B AlimdeBa C AlitudeBo D altiudect E alimdeBr F Ident Switch In H alitdecs ly altiudead K alimdeaz L aliwdeca M alitudear LN Do Not Connect The following diagram shows the connector orientation as it would be fitted to the mounting tray Wiring Side Transponder Side Trig Avionics Limited Page 9 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 4 2 Secondary Interface Pinout Pin Signal Direction Ground aa TIS Traffic Out GPS Position In Reserved Audio Mate In 6 Altitude Alert Ground B Audio Output c Output Reserved LE Reserved r Reserved Wiring Side PinA 5 4 3 Orientation Diagram To assist in connector orientation the following example shows a typical set of connections This diagram shows the expected connector positions when viewed from the transponder side of the tray looking into the tray from the front In the example shown the aircraft uses a 14 volt lighting bus a parallel altitude encoder a DME with simple suppression output a GPS with serial position output and a simple lamp for the altitude alerter This example is representative of a simple fixed gear 14 volt aircraft DME Optional Antenna Power In Suppress D4 Lighting Altitude Alert GPS Position Ground Page
3. Vibration 8 0 Aircraft zone 2 type 3 4 5 to category S level M Equipment at strike off level 3 also tested for aircraft zone 2 type 1 Helicopters to category U level G Explosion 9 0 Equipment identified as Category X no test required Waterproofness 10 0 Equipment identified as Category X no test required Fluids Susceptibility 11 0 Equipment identified as Category X no test required Sand and Dust 12 0 Equipment identified as Category X no test required Fungus 13 0 Equipment identified as Category X no test required Salt Spray 14 0 Equipment identified as Category X no test required Magnetic Effect 15 0 Equipment tested to Category Z Power Input 16 0 Equipment tested to Category B Voltage Spike 17 0 Equipment tested to Category B Audio frequency conducted susceptibility 18 0 Equipment tested to Category B Induced signal susceptibility 19 0 Equipment tested to Category AC Radio frequency susceptibility 20 0 Equipment tested to Category T Radio frequency emission 21 0 Equipment tested to Category B Lightning induced transient susceptibility 22 0 Equipment identified as Category XXXX no test required Lightning direct effects 23 0 Equipment identified as Category X no test required Icing 24 0 Equipment identified as Category X no test required Electrostatic Discharge 25 0 Equipment identified as Category X no test required Fire Flammability 26 0 Equipment identified as Category C Page 30
4. transponders and DME systems and between transponders and collision avoidance systems The TT31 provides two styles of mutual suppression interface on the 24 way connector The Suppress input on contact 9 is typically used in aircraft with simple DME systems and no other suppression requirements It is an input only and is active whenever the input is greater than approximately 5 Volts The Suppress I O on contact 4 is an ARINC compatible suppression bus interface which acts as both an input and an output The TT31 will assert this signal when it is transmitting and can be suppressed by other equipment that asserts the signal The TT31 will drive approximately 24 Volts on the output independently of supply voltage and will treat the input as active whenever the bus has greater than 10 Volts 5 5 4 Altitude Inputs and Output The TT31 can use either a parallel Gray code altitude input or serial RS232 altitude input Both of these interfaces are on the 24 way connector If the altitude encoder you are using offers both we recommend using the RS232 serial input Serial formats allow a higher resolution altitude representation that can be used by Mode S interrogations whereas parallel Gray code format can only represent altitude to the nearest 100 feet You must choose between serial or parallel formats you should NOT connect both If a parallel encoder is connected the TT31 will always use that as the altitude source even if a serial encod
5. 7 2 BNC Comnector aii il fac 16 5 8 TRAY BNC CONNECTOR ASSEMBLY TT 17 6 INSTALLATION SETUP AND TEST ssososssoooocooooco0oo0o0o0oosocoosovsrocorersonsrsresrorerosrsrorsrosrsreronrsrsrosrsn 19 6 1 CONFIGURATION ITEMS T as 19 6 1 1 Aircraft Address Programming sss sese eee eee 19 6 1 2 VERS quawkCode ie 19 6 1 3 VER FUSHKEID Sa as 19 6 1 4 Airspeed Category Linda ais A hae OTTS Tt aE aaa 20 6 1 5 ALICIA COOL LT Aa 20 6 1 6 SQUAt S WIEN OUTCE tii drid dd tds ds 20 6 1 7 TIS OUD UE aia cha os saa sags NASN sass ias aora VASSA NAN ANNA NR aiii aii 20 6 1 8 OPSINPUE SA A SNES bar SRA EN Se ek Se ates Sees 20 6 1 9 GPS TIS Lind Speed oil A A A A 20 6 1 10 GPS System Certification LeVel sissisesessssesssssrsbobsssossssssossnb nrdbnsiosssrnsnanstnsssrisnennendansirses 20 OL IIS GPS NA CV ia 21 6 1 12 Aircraft Length and Wid ness Renaat arer RT ERO RST OTER ENRERE RG RT RET 21 6 113 GBSAntenna O Seta SS 21 6 1 14 ADS B Receiver Options erosi ieo n aa eR aE ri EAE aE aE siare 21 OLAS Audio Volume diia 21 6 1 16 LCD Dim TT 21 OLA LOD LTE jasa 22 6 2 TESTITEMS oesi eer E EAEE da sede AE da subdue ch cates id fa a es n N r r va E id EEEE 22 6 2 1 Interface Check bean uses soleadas dilatada 22 6 2 2 Altit de Check arieni E A E EEEa 22 6 2 3 PAQNENG BUS sa a a de A a E eta 22 6 2 4 GBS Interfase ates 22 7 POST INSTALLATION CHECKS oossssseoooossoocoococsssocscocoosossonorsrororersroresrorosrsrsrorrsrorosrsreronrsrsrosn sn 23 8
6. Ki a E ae 6 4 4 REQUIRED ITEMS nn vre teen vsctnssevdtssden eve rsn adde ese sa Cae sae Tags E ua Pau ea Sage bu NAS tiders ter 6 5 INSTALLATION AA ON 8 5 1 UNPACKING AND INSPECTING EQUIPMENT ss sccccccecsesessscecececeessueceeceeceeseneaeeeesceesenseaeeeeeeeenes 8 32 MOUNT Gi 8 5 3 COOLING REQUIREMENTS cccccccscssssscccecececsensnaececececsessnaececececsensnaeaeeececeessaeaecececsenensnaeseeeeeenes 8 5 4 ELECTRICAL CONNECTIONS orense EERE 8 5 4 1 Primary Interface Pinout oui ie e asi iei E DRN re nacen rra cnn ESEE 9 5 4 2 Secondary Interface POM sss esse essen 10 5 4 3 Orientation Did gram sssrinin eTa A Eea EA ATA EAR ESEN Ea a e 10 5 5 INTERFACE DETAI Scania i 11 5 5 1 DOWETINpDUE orrai na bs cottages E ERIA EE eaS E E REEE 11 D2 Lighting TET A da 11 5 5 3 Mutual Suppression iii a ea iaa desata 11 5 5 4 Altitude Inputs and Output sss sss esse eee 11 5 5 5 Squat Switeh INPUT rereana Sas ayia E EE E E R EEA E EE rr EN 12 5 5 6 Ident S witch Input ii EN 12 5 5 7 External Standby Mpt cicccescosdsind vast sss iii 12 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 5 8 A di aT 12 5 5 9 Altitude Alerter Output ica 12 9 310 GPS Position Input A ip id 13 IDII STIS Traffic OUI pits ricas ti a e A 13 5 0 MOLEX CRIMP TERMINALS iasan aE R EEA E E E R 13 If ANTENNA INSTALLATION enire eeir e Eaa a K Ea A A AE AEE EASE 14 5 7 1 Antenna Cable A ar a A di E eR dE 14 5
7. NORMAL OPERATION segar azereg ezer azereg eirs ezerest 24 8 1 OVERVIEW escri ee r ea ra cena tii 24 8 27 DISPLAY tds 24 il Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 8 3 MODE SELECTOR KNOB 00s00sesecvevevsveveveveesvevevevevevsvscsvevevevsvevevecsvevevevevevsvssevevevevevevsvsvsvevss 24 8 4 PUSH BUTTONS f l yess amp obeests It BAER r sera os ev Sabet A SA Beas Boa oe 25 8 5 CODE SELECTOR NOBIS a a ee Rs Ss 25 8 6 FLIGHT TIMER 3 s doh seuss de ed seueebdv scones 25 8 7 STOPWATCH voces secs an acces hake a aa eg OE aig ad ag od eo ibs 25 8 8 ADS B POSITION MONITOR ccccccccccececececececececececececececececececececscececececececececececececececececececess 25 8 9 ATTITUDE MONITOR 4 a A A di 26 8 10 WARNINGS occoccccccncnononononononononononononononononononononononononnnnnonnnononnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnonnnannnnnnnnnanos 26 O TT FAULT ANNUNOIA TION ta cc 26 8 12 LOW TEMPERATURE OPERATION eee 26 9 CONTINUED AIRWORTHINESS sccccssssscssssscccssssccccssscccssssccccssseccccssscscsssscescssseccscssssecees 27 10 LIMITED WARRANTY s ssec0 0 ss ssss osss0s05685s600d508s0s0 60808s8808s0800600860080250040 0s805s0 0seed sssnosssasssses 28 11 ENVIRONMENTAL QUALIFICATION FORM ssssccsssssccsssscccsssscccsssscccessssccccsssessees 29 12 ADS B COMPEIANGE rnnr 500042 6d000000558 000 6d800000 EE EAEN rS Nie 31 12 1 ADS B PARAMETERS SUPPOR
8. ONE INPUT TO THE LIGHTING BUS DEPENDING ON LINE VOLTAGE LAMP SHOWN AS EXAMPLE OF POSSIBLE ALERTER INSTALLATION OTHER OPTIONS ARE POSSIBLE gt Be ie Trig Avionics Limited TT31 Transponder Installation Manual 00455 00 This page intentionally left blank Trig Avionics Limited
9. OUT DIMENSIONS FOR gt BEHIND AIRCRAFT PANEL MOUNT o mM a S 2 me 160 30 I o g CUT OUT DIMENSIONS FOR Y FRONT AIRCRAFT PANEL MOUNT t top1 10 70 240 75 M 36 62 11 20 04 016 PLACES i IR g 2 N y i l 9 left1 N 177 80 200 ALLOWANCE FOR AIRCRAFT PANEL THICKNESS All dimensions in millimetres Trig Avionics Limited Page 33 TT31 Transponder Installation Manual 00455 00 14 Basic Interconnect Diagram Oo Lu Q Z O a op Z lt Oc E AN Lu Q O m E E Oc E Ground Lighting 14V Lighting 28V Suppress I O Squat Switch Serial Alt Out Serial Alt In Suppress In Ext Standby 11 33V DC 11 33V DC Ground Ext Ident Alt D4 Alt B4 Alt B2 Alt C1 Ground TIS Output GPS Input Reserved Audio Mute Alt Alert Ground Audio Audio Reserved Page 34 Coax gt gt MUTUAL SUPPRESSION BUS O OTHER TRANSPONDER L QA LAMP 3A CIRCUIT BREAKER 1A T J 33V PARALLEL ALTITUDE ENCODER CIRCUIT BREAKER GPS POSITION SOURCE SERIAL ALTITUDE ENCODER or ADC AA DME TRAFFIC DISPLAY AUDIO PANEL 27 March 2012 Issue AM NOTES ALL WIRES SHOULD BE 18 24 AWG ONLY CONNECT ONE ALTITUDE DATA SOURCE EITHER A SERIAL ENCODER PARALLEL ENCODER OR ADC WHEN USING DATA FROM AN ADC IT SHOULD BE CONNECTED TO THE SERIAL ALT IN AS SHOWN CONNECT ONLY
10. aircraft can receive traffic information To limit channel congestion these services are only provided to aircraft equipped to receive them The transponder reports what receivers are installed in a periodic status message enter the receiver status here 6 1 15 Audio Volume The altitude alert function includes an audio alert This configuration item lets you adjust the audio volume output from the transponder using the rotary knob Whilst you are turning the volume control the transponder will periodically output a test signal to verify the settings 6 1 16 LCD Dim Point The LCD backlight illumination is controlled automatically by the ambient light sensor Depending on the amount of light spill in the cockpit and the brightness of other adjacent avionics displays it may be necessary to adjust the darkest setting of the backlight to best match other equipment and to improve the cockpit appearance Note it is only practical to do this in pitch darkness since that is the in flight environment that you are trying to reproduce If you are working in a hangar with any other lighting it may be better to leave the setting in the mid range Trig Avionics Limited Page 21 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 6 1 17 LCD Brightness The actual maximum brightness of the LCD cannot be increased with this control What it controls is the rate at which the lighting increases in brightness as the ambient light
11. heat on the connector body Page 16 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM e Slide heat shrink tubing forward flush to connector and heat to shrink the tubing e Complete the assembly by installing the bushing over the centre contact and fitting the cap Solder the cap in place in at least two places 00242 00 Trig Avionics Limited Page 17 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM When the BNC is prepared feed it through the TT31 mounting tray and attach the washer combination in the following order e Wave washer p n 00317 00 e Plain washer p n 00241 00 e Circlip washer p n 00242 00 The Circlip washer should be fitted with a set of Circlip pliers The two Molex connectors should be passed through the openings in the rear of the tray and then mounted firmly to the tray from the inside using the four M3 screws supplied Page 18 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 6 Installation Setup and Test The TT31 uses a simple setup system to program important system parameters including the Mode S address In the original factory configuration the setup screen is the first thing that runs when you switch on the transponder If the transponder has already been configured and you want to access the setup screen again simply hold down the FUNC button while s
12. operating in flight mode either ON or ALT Press the FUNC button to display the Flight Timer 8 7 Stopwatch The stopwatch can be used as a convenient timer Press the FUNC button to display the stopwatch Pressing ENT will reset and start the timer Pressing ENT again will stop the timer 8 8 ADS B Position Monitor The ADS B position monitor is available on aircraft equipped for ADS B position output It provides a convenient way of verifying that valid position information is being received by the transponder by displaying the current calculated position If a valid position is displayed the transponder will be transmitting that position to ADS B participants If no position is available the position will be Trig Avionics Limited Page 25 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM displayed as dashes and the transponder will NOT be transmitting ADS B position information 8 9 Altitude Monitor The Altitude Monitor activates an audio annunciator or annunciator light depending on installation when the aircraft pressure altitude differs from the selected altitude by more than 200 feet Press the FUNC button to display the altitude monitor enable screen Pressing ENT toggles the altitude monitor at the current altitude When altitude monitoring is in use a small deviation pointer appears adjacent to the altitude display on the transponder 8 10 Warnings There are two warning messages that can be d
13. supplies RS232 output levels and runs at 9600 bps no parity The output format is always Icarus Trimble Garmin format If the altitude source is a parallel encoder the serial output is reported every 0 5 seconds if the source is a serial encoder the output simply repeats the input reports each report delayed by up to 10 milliseconds from the corresponding input report 5 5 5 Squat Switch Input The Squat switch input allows the transponder to automatically switch between Airborne and Ground modes of operation The squat switch will also automatically start and stop the flight timer The input will be asserted when the voltage to ground is pulled below approximately 4 Volts The operating mode of the squat switch can be programmed during setup to allow for active low or active high logical behaviour For aircraft with no squat switch this input should be left open circuit and the setup mode programmed for Not Connected 5 5 6 Ident Switch Input The Ident switch input on the 24 way connector allows the IDENT function to be selected using a remote switch The input is active low and will be asserted when the voltage to ground is pulled below approximately 4 Volts 5 5 7 External Standby Input This input when held low places the transponder in Standby mode It should be used to switch between transponders in an installation with two transponders The input is active low and will be asserted when the voltage to ground is pull
14. 10 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 5 Interface Details 5 5 1 Power Input The power supply can be 11 33 Volts DC no voltage adjustment is required Contacts 11 and 12 on the 24 way connector are both available as power inputs This is for compatibility reasons only internally the two are connected together and in most installations only one need be connected to the power supply Use a 3 Amp circuit breaker for power supply protection to the TT31 5 5 2 Lighting Bus Input The TT31 will adjust the brightness of the front panel switch lighting according to the voltage on the lighting bus input Two lighting bus inputs are provided on the 24 way connector to accommodate aircraft with 14 Volt or 28 Volt lighting systems When the lighting bus operates at 28 Volts connect the bus input to contact 3 and leave contact 2 unconnected When the lighting bus operates at 14 Volts connect the bus input to contact 2 In this case contact 3 can be left unconnected but for backwards compatibility may also be grounded instead with no effect If no lighting bus input is detected the TT31 will automatically control the front panel lighting based on the ambient light sensor 5 5 3 Mutual Suppression Mutual suppression allows two or more transmitters on adjacent frequencies to inhibit the other transmitters when one is active to limit the interference effects It is commonly used between
15. 2 VFR Squawk Code When the pilot presses the VFR button a pre programmed code will replace the current squawk code The code is set up next the choice of code will depend on the normal location of the aircraft In the USA the VFR squawk code is 1200 In most parts of Europe the VFR squawk code should be set to 7000 Enter the 4 digit squawk code using the rotary knob and the ENT button 6 1 3 VFR Flight ID The default Flight ID for an aircraft not on an IFR flight plan should be the aircraft registration Enter Trig Avionics Limited Page 19 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM the aircraft registration using the rotary knob and the ENT button Note that the aircraft registration is loaded as letters and numbers only There are no dashes or other punctuation marks and no spaces can be inserted When you enter a space it finishes the data entry and moves to the next item 6 1 4 Airspeed Category Mode S transponders can transmit their maximum airspeed characteristics to aircraft equipped with TCAS This information is used to help identify threats and to plan avoiding action by the TCAS equipped aircraft The airspeeds are grouped in ranges using the rotary knob select the range that corresponds to the aircraft 6 1 5 Aircraft Category To assist ATC tracking of aircraft an aircraft category can be transmitted by Mode S transponders Using the rotary knob select the aircraft category that mo
16. 25 Watts minimum at antenna after allowing for 0 5dB connector losses and 1 5dB cable losses 6M75 V1D 1030 MHz 74dBm 3dB 3 1 1 Approved Deviations The TT31 ADS B function is certified to ETSO C166a which references DO 260A as the applicable standard the TT31 implements DO 260B which has replaced DO 260A The TT31 ADS B function is certified to FAA TSO C166b which references DO 260B but also refers to the environmental standard DO 160F and indirectly refers to the transponder standard DO 181D The TT31 transponder certification was carried out to DO 160E and DO 181C DO 181D introduced a new requirement in section 2 2 8 6 response in the presence of CW carrier wave interference The TT31 was designed prior to this requirement and behaves differently to DO 181D The TT31 will report a FAULT message if CW interference is experienced and will not reply Although this is different to the new requirement this behaviour mitigates the impact of CW interference since the pilot will be able to see that ATC replies are not being sent 3 2 Physical Specifications in Tray Specification Characteristics 40mm 1 57 160mm 6 30 239mm 9 4 2 8lbs 1 35Kg Page 4 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 3 3 Installation Approval The conditions and tests required for the TSO approval of the TT31 Mode S Transponder are minimum performance standards It is the re
17. Mode S Transponder ltems Your TT31 Mode S transponder includes the following items Unit Description Part Number TT31 Mode S Transponder 00220 00 01 TT31 Mounting Tray 00231 00 TT31 Documentation Kit 00233 00 TT31 Installation Kit 00223 00 4 2 Installation Kit Your TT31 installation kit includes the following items Unit Description Part Number 12 way double sided crimp housing 00032 00 connector 24 way double sided crimp housing 00033 00 connector Crimp Terminal Female 18 24 AWG 00236 00 Screw Pozidrive Pan Head M3x12mm lg 00422 00 Connector Co axial Panel Mount Right 00239 00 Angle Blind Mate Circlip 7 16 External 00242 00 Washer 7 16 Plain Stainless Steel 00241 00 Washer 7 16 Crinkle Beryllium Copper 00317 00 4 3 Documentation Kit Your TT31 documentation kit includes the following items Unit Description Part Number TT31 Transponder Installation Manual 00455 00 TT31 Pilots Operating Manual 00454 00 4 4 Required Items Additional items you will require but which are not in the TT31 package include e Antenna and fixing hardware The TT31 is compatible with any transponder antenna approved to ETSO C74 or 2C112 e Altitude encoder You require an encoding altimeter or a blind encoder with either parallel Gray code or RS232 serial output For best results and simpler installation an encoder with a serial output is recommended e Cables You need to supply and fabricate all req
18. Page 15 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 72 BNC Connector This section describes the technique for attaching the antenna cable to the supplied blind mate BNC connector If a low loss cable is needed that has too large a dielectric diameter to fit the supplied blind mate BNC connector a short length up to 150mm or 6 inches of smaller cable may be used with suitable mating connectors to adapt to the transponder connector e Strip back the coax cable to the dimensions in the table as shown in the diagram below Slide 25 mm 1 inch of heat shrink tubing over the cable Heat Shrink Tubing _ p Dimension Cut size Cut size mm inches A 12 7 0 5 B 6 4 0 25 3 2 0 125 e Insert the cable into the connector the inner conductor should align with the centre contact the inner shield should be inside the body of the connector and the outer shield should be outside the body Outer Shield ee Inner Shield e Solder the centre conductor to the centre contact aligning the conductor with the slot in the contact Avoid excess solder heat on the centre BNC conductor pin e Solder the inner shield to the inside of the connector body by applying a soldering iron to the body and running solder into the gap Try to avoid excess solder heat on the connector body e Solder the outer shield to the outside of the connector body Avoid excess solder
19. S position input is an RS232 input to the transponder The ADS B features are optional no GPS is required for normal Mode S Elementary Surveillance The TT31 GPS input can recognise the following protocols e Industry standard Aviation protocol e NMEA 0183protocol e Freeflight and NexNav GPS proprietary protocols e Garmin ADS B protocol The interface speed can be selected between 4800 9600 and 19200 bps Some of the protocols listed above may not contain all the required data for a compliant ADS B message depending on the intended airspace regulations For further information refer to Section 12 ADS B Compliance of this manual 5 5 11 TIS Traffic Output The TIS traffic output supports the display of uplinked Traffic Information Service messages It is an RS232 output on the 12 way secondary connector The TT31 TIS output can drive the Trig proprietary traffic protocol and can also support the format used by certain Garmin handheld displays including the 495 496 695 and 696 Note TIS is a Mode S uplink service that is provided by some US approach radars TIS coverage is limited to the coverage areas of those radars There is no TIS provision outside the USA 5 6 Molex Crimp Terminals The Molex connector contacts should be wired with wire of 18 24 AWG The contacts are compatible with a wide range of crimp tools Ensure that the contact has been crimped using both the conductor crimp and the insulator crimp Conducto
20. TED esse 31 122 FAA 91227 EOMPLIANGE avestooiev toseerveetind ver a ES 31 12 35 AME 20 24 COMPIETANGE iii 32 12 4 AUTOMATIC AIR GROUND DETERMINATION sees ee eee 32 12 5 ADS B SUPPORT sss 32 13 INSTALLATION DRA WINGS 5vvsss ss0008ssas0sssssss so8ov0s0s 538ss0 sso0ss0s0veseosssgosssvo dssedesssovsssessnsonskese 33 14 BASIC INTERCONNECT DIAGRAM cssscccssssccesssscccsssccccssssccccssccscsssaccscssssececsseecees 34 Trig Avionics Limited iii TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM This page intentionally left blank iv Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 1 Preface 1 1 Purpose This manual describes the physical and electrical characteristics and the installation requirements for a TT31 Mode S Transponder 1 2 Scope This document applies to the installation of the TT31 Mode S Transponder At the publication date of this manual the software version identifier for the TT31 is 3 1 and the FPGA version identifier is 231006a The software and FPGA versions are subject to change without notice 1 3 Changes from Previous Issue Changes from Issue AL to Issue AM are Section 5 5 4 Addition of Shadin air data computer ADC compatibility Section 5 5 11 Addition of GARMIN ADS B protocol compatibility Section 12 Additional GPS units listed for ADS B compliance Section 14 Wiring Diagram updated to make pin identific
21. TRIG TT31 Mode S Transponder Installation Manual 00455 00 AM 27 March 2012 Trig Avionics Limited Heriot Watt Research Park Riccarton Currie EH14 4AP Scotland UK Copyright Trig Avionics Limited 2012 This page intentionally left blank TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM CONTENTS Ie PREFACE sa iissicskcnsiissscsssncsscnnssess aiie N N E EN A EN E E A 1 1 1 PURPOSE e ranea a e E iia i 1 1 2 SCOPE suda 1 1 3 CHANGES FROM PREVIOUS ISSUE soiin nei e e aa a a E AE RERE 1 1 4 DOCUMENT CROSS REFERENCES sees eee 1 A NAS O 2 2 1 TT3T DESCRIPTION cocos loro oponen cid obabi R E A ham eigen aii 2 22 INTERFACES NN 2 3 TECHNICAL SPECIFICATIONS e e esesesesesesesesesesososososososososososososososesosososososososesososososososossosose 4 3 1 REGULATORY a ii EE 4 3 1 1 Approved Deviations sisirain niinn iaia DNR sans delas die cial 4 3 2 PHYSICAL SPECIFICATIONS IN TRAY ccssscccssssececsssceceessececssseeeecsececsssaececsesaececseseecsesaeeecneaaess 4 3 3 INSTALLATION APPROVAL sisyccisiitvassssisncosdceceashessteds idatneb onan E E A E E OaE E NATER RATES 5 3 4 NON TSO FUNCTIONS e 5 4 UNIT AND ACCESSORIES SUPPLIED e esersrerererorcrcscreroresesorerorororeroeororerossrorseesoroeoesosososeseee 6 4 1 TT31 MODE S TRANSPONDER TEMS cesccessseceseeecsecesceecsneceneeceaeceseeeceaeceeeecsaeeeeneecsaeesenters 6 4 2 NENA AAA aa a a i aaa RE EE TE AEE ITEE 6 4 3 DOCUMENTATION
22. Transponder Installation Manual 00455 00 27 March 2012 Issue AM Because the ETSO for ADS B was published later than the ETSO for transponders it refers to a later edition of the environmental standard ED 14E DO 160E rather than ED 14D DO 160D The following form provides the environmental data in DO 160E format The two tables are equivalent Nomenclature TT31 Mode S Transponder Part Number 00220 XX ETSO C166a Manufacturer Trig Avionics Limited Address Heriot Watt Research Park Riccarton Currie Scotland EH14 4AP Conditions DO 160E Description of Conducted Tests Temperature and Altitude 4 0 Equipment tested to Categories A4 C4 Low temperature ground survival 4 5 1 55 C Low temperature operating 4 5 1 20 C High temperature operating 4 5 3 55 C High temperature short time operating 4 5 2 70 C High temperature ground survival 4 5 2 85 C Loss of Cooling 4 5 4 Cooling air not required 70 C operating without cooling air Altitude 4 6 1 35 000 feet Decompression 4 6 2 8 000 to 35 000 feet in 15 seconds Overpressure 4 6 3 15000 feet Temperature Variation 5 0 Equipment tested to Category C Humidity 6 0 Equipment tested to Category A Operational Shocks 7 2 Equipment tested to Category B Crash Safety 7 3 Equipment tested to Category B and extended to use test levels for Helicopters
23. ation clearer 1 4 Document Cross References 00454 00 TT31 Mode S Transponder Operating Manual AE Trig Avionics Limited Page 1 27 March 2012 Issue AM TT31 Transponder Installation Manual 00455 00 2 Introduction 2 1 TT31 Description The TT31 Mode S panel mount transponder is an ED 73B Class 1 compliant Mode S level 2es datalink transponder with support for extended squitter elementary surveillance and SI codes The TT31 is also a DO 260B Class B1S compliant ADS B out participant The TT31 meets the relevant environmental requirements of ED 14D and is certified to ETSO 2C112b ETSO C166a TSO C112 and TSO C166b The TT31 transmitter power output is nominally 240 watts and the transponder runs from either 14 volt nominal or 28 volt nominal DC power supply with no configuration changes required The TT31 transponder responds to both legacy Mode A C interrogations and to Mode S interrogations from both ground radar and airborne collision avoidance systems In all cases the interrogations are received by the transponder on 1030MHz and replies are transmitted on 1090MHz In the Mode S environment S stands for Select and a Mode S interrogator can selectively address a single transponder This allows accurate position plotting with lower reply rates which in turn reduces frequency congestion and interference As a side benefit power consumption by the transponder may be reduced and simple datalink services can be supported
24. e altitude in hundreds of feet When non standard atmospheric conditions apply this may not match the altimeter indicated altitude but will be correctly displayed by the ATC radar 8 3 Mode Selector Knob The left hand knob controls the power to the transponder and the operating mode OFF Power is removed from the transponder SBY The transponder is on but will not reply to any interrogations GND The transponder will respond to Mode S ground interrogations from surface movement radar ON The transponder will respond to all interrogations but altitude reporting is suppressed ALT The transponder will respond to all interrogations When airborne the transponder should always be set to ALT unless otherwise directed by Air Traffic Control When you are taxiing on the ground the transponder should be set to GND unless your installation includes a gear squat switch Aircraft installations that include a gear squat switch will automatically select GND on landing Page 24 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 8 4 Push Buttons IDENT Press the IDENT button when ATC instructs you to Ident or Squawk Ident This activates the SPI pulse in the transponder replies for 18 seconds IDENT will appear in the display FUNC Pressing the FUNC button provides access to the flight timer stopwatch and altitude monitor function When the aircraft is ADS B equipped pressing FUNC al
25. ed below approximately 4 Volts 5 5 8 Audio Output The Audio Output is on the 12 way secondary connector The Audio Output is a balanced two wire audio output that can be connected to an unswitched input on the aircraft audio panel Audio output is up to 10 Volts peak to peak across the pair when driving a 600 Ohm load actual level can be adjusted at installation see Section 6 Note The audio pair is not a true transformer balanced output both pins are actively driven If the audio panel input is single ended then only one of the output pins should be used together with a local ground pin the other audio output should be left floating The Audio Output carries the traffic alert messages for TIS and the altitude audio annunciator used by the altitude monitor function 5 5 9 Altitude Alerter Output The TT31 includes an altitude monitor function that can alert the pilot to altitude deviations in cruise flight The altitude alerter output on the 12 way secondary connector is switched to ground when the altitude deviation is detected and can be connected to a warning light or sounder to warn the pilot The output is an open collector transistor and can sink up to 1 Amp DC The switched voltage should not exceed 60 Volts Page 12 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 5 10 GPS Position Input The GPS position input is required to support ADS B functionality The GP
26. er is also connected The parallel encoder inputs are active when the voltage to ground is pulled below approximately 4 Volts The TT31 includes internal isolation diodes which prevent the unit from pulling the encoder lines to ground when the transponder is switched off The TT31 can therefore share the altitude inputs with other devices without needing external isolation Parallel output altitude encoders intended for operation below 30 000 feet may not have a signal connection for D4 In an aircraft with a service ceiling below 30 000 feet input D4 will never be active and can safely be left unconnected Trig Avionics Limited Page 11 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM The serial encoder input uses RS232 input levels The communication should be 9600 bps no parity The TT31 will correctly recognise either Icarus Trimble Garmin format altitude data or RMS format altitude data Refer to the encoder documentation to determine jumper settings as appropriate The TT31 can also accept Shadin family Format G Format S and Format Z air data protocols which supply both altitude and airspeed information The airspeed information can be used to provide an automatic air ground determination for an ADS B installation The TT31 includes a serial altitude output which repeats the altitude received on the encoded input either parallel or serial for connection to a GPS or other equipment The serial output
27. he VSWR e To prevent RF interference the antenna must be physically mounted a minimum distance of 3 feet from the TT31 Mode S transponder Electrical connection to the antenna should be protected to avoid loss of efficiency as a result of the presence of liquids or moisture All antenna feeders shall be installed in such a way that a minimum of RF energy is radiated inside the aircraft 5 7 1 Antenna Cable The TT31 is designed to meet Class 1 requirements with an allowance of 2 dB for loss in the connectors and cable used to connect it to the antenna Excessive loss will degrade both transmitter output power and receiver sensitivity Allowing 0 25dB loss for the connector at each end of the antenna cable assembly leaves an allowance of 1 5dB maximum loss for the cable itself An acceptable cable e Has less than 1 5dB loss for the run length needed e Has a characteristic impedance of 50 Ohms e Has double braid screens or has a foil and braid screen Once the cable run length is known a cable type with low enough loss per metre that meets the above requirements can be chosen Longer runs require lower loss cable NOTE Low loss cable typically uses foamed or cellular dielectrics and foil screens These make such cables especially prone to damage from too tight bends or from momentary kinking during installation Once kinked these cables do not return to full performance when straightened The following table is a guide to the maximum u
28. increases This allows the brightness to be matched to other avionics displays during light level changes as far as possible 6 2 Test items 6 2 1 Interface Check The Interface Check screen displays the current state of the external IDENT external STANDBY and external GROUND inputs Exercise these inputs to confirm the correct behaviour 6 2 2 Altitude Check The Altitude check displays the current state of the altitude inputs Individual Gray code lines are shown to assist in fault tracing 6 2 3 Lighting Bus The lighting bus check displays the voltage on the lighting bus to assist in verifying the correct operation of the lighting bus 6 2 4 GPS Interface The GPS interface check provides a simple confidence check that the transponder is receiving data on the RS232 input Note that this check does not attempt to decode the received data it is intended only to provide a quick wiring check in the hangar To assure that the interface is fully operable the aircraft should be tested with the transponder in normal operating mode with the GPS receiver operating correctly and a ramp test of the transmitted parameters completed Page 22 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 7 Post Installation Checks Post installation checks should be carried out in accordance with your certification requirements These checks should include Mode S interrogations to verify correct address
29. isplayed on the transponder Warning messages can be cleared by pressing the ENT key on the control panel If the transponder has been configured for ADS B operation but a suitable position fix is not available a warning message is displayed to indicate that ADS B capability has been lost The transponder will continue to operate normally If there is a problem with the antenna installation a warning message may be displayed Depending on whether this is an intermittent problem the message may recur when cleared The transponder may still be replying to interrogations but there can be no assurance that ATC is receiving those replies 8 11 Fault Annunciation Tf the transponder detects an internal failure or a hard fault with the antenna installation the screen will indicate FAULT and a brief statement of the problem No replies will be made to interrogations when a fault is detected 8 12 Low Temperature Operation The TT31 is certified for correct operation at temperatures down to 20 Celsius At low temperatures however the display performance will be impaired The aircraft cockpit should be warmed to allow normal operation of the transponder before takeoff Page 26 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 9 Continued Airworthiness Other than for periodic functional checks required by the regulations the TT31 Mode S transponder has been designed and manufactured to allow o
30. lowing GPS units to form the basis of a 14 CFR 91 227 compliant ADS B installation Trig Avionics Limited Page 31 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM e Freeflight 1201 amp 1204 WAAS GPS Sensors e NexNav MINI amp NexNav MAX WAAS GPS Sensors e G in GNS 400W S00W_seri For installations seeking certification to 91 227 or other applicable standards additional compliance information is available on request from Trig Avionics Limited 12 3 AMC 20 24 Compliance The TT31 transponder can be connected to the following GPS units to form the basis of an AMC 20 24 compliant ADS B installation e Freeflight 1201 amp 1204 WAAS GPS Sensors e NexNav MINI amp NexNav MAX WAAS GPS Sensors e Garmin GNS 400W 500W series For installations seeking certification to AMC 20 24 or other applicable standards additional compliance information is available on request from Trig Avionics Limited 12 4 Automatic Air Ground Determination The TT31 can report ADS B surface and airborne messages The ADC or squat switch inputs can be utilised to determine air ground status as explained in section 5 12 5 ADS B Support If you require additional information and data to support an ADS B installation then please contact support trig avionics com Page 32 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 13 Installation Drawings 137 10 o CUT
31. n condition maintenance This means that there are no periodic service requirements necessary to maintain continued airworthiness and no maintenance is required until the equipment does not properly perform its intended function When service is required a complete performance test should be accomplished following any repair action Repairs should only be carried out in accordance with Trig Avionics Limited service procedures Trig Avionics Limited Page 27 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 10 Limited Warranty Trig Avionics Limited warrants our products to be free from defects in materials and workmanship for a period of two 2 years from the date of installation by an authorised dealer This warranty covers repair and or replacement at our option of any parts found to be defective provided such defects in our opinion are due to faulty material or workmanship and are not caused by tampering abuse or normal wear All warranties are F O B Trig Avionics Limited Heriot Watt Research Park Riccarton Currie EH14 4AP Trig Avionics will not accept or pay for any charges for warranty work performed outside our factory without prior written consent This warranty applies only to products in normal use It does not apply to units or circuit boards defective due to improper installation physical damage tampering lightning or other electrical discharge units with altered serial numbers or units
32. n the transponder If the position indications are all dashes then either the GPS position is not valid or the GPS interface is not correctly configured Whenever a valid position is received by the transponder and the transponder is in any mode other than Standby ADS B Extended Squitters should be observed on the transponder test set Where installed verification of the TIS output A Mode S test set with TIS capability should be used with the transponder in ALT mode traffic should be shown on the attached display Trig Avionics Limited Page 23 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 8 Normal Operation 8 1 Overview On the front panel is an amber backlit LCD display flanked by a rotary mode selector knob OFF SBY GND ON and ALT and a continuously rotating knob used for code and data entry Ident Active Reported Reply Flight ID Enter Back Button Mode Altitude Indicator and Squawk Button Button E Ea Mode Function Light VFR Flight ID Squawk Code Knob Button Sensor Button Button Knob 8 2 Display The display shows the operating mode of the transponder the reported pressure altitude and the current squawk code and Flight ID The reply indicator is active when the transponder replies to interrogations The pressure altitude is displayed as a Flight Level which is the pressur
33. nd width wingspan in metres and will calculate the appropriate size code for transmission 6 1 13 GPS Antenna Offset The GPS antenna offset is used together with the aircraft length and width to manage taxiway conflicts A typical GPS installation does not report the geographic position of the centre of the aircraft or even the tip of the nose of the aircraft instead it usually reports the location of the actual GPS antenna not the GPS receiver In normal flight operations this distinction is of no practical importance at all but if ADS B is used to manage taxiway conflicts a significant offset in antenna position could mean that the aircraft is not in the same place as the ADS B reported position Although primarily intended for position correction on large transport aircraft General Aviation aircraft can also have a significant offset For example if the aircraft has a long tail boom and the GPS antenna is on the top of the tail the GPS position could be 15 feet or more from the nose of the aircraft Enter the position of the GPS antenna relative to the nose of the aircraft The position is stored and transmitted to the nearest 2 metres great accuracy in measurement is not required 6 1 14 ADS B Receiver Options In the USA there are two ADS B channels 1090ES and UAT and there is an ADS B based traffic information service called TIS B The ADS B ground stations relay this information between the two channels so that suitably equipped
34. oes not need to be kept away from other devices for this reason e Avoid sharp bends and placing the cables too near to the aircraft control cables e Secure the mounting tray p n 00231 00 to the instrument panel via the six 6 mounting holes in the tray It is important that the tray is supported at the rear two mounting holes as well as the front four e Check that the locking mechanism is correctly oriented by unscrewing the locking screw if required e Slide the TT31 transponder into the secured mounting tray e Lock the TT31 transponder into the mounting tray using a 3 32 Allen key taking care not to over tighten the locking screw 5 3 Cooling Requirements The TT31 Mode S transponder meets all applicable ETSO requirements without forced air cooling Attention should however be given to the incorporation of cooling provisions to limit the maximum operating temperature of each unit when the TT31 is installed in a typical panel or rack The reliability of equipment operating in close proximity in a rack can be degraded if adequate cooling is not provided 5 4 Electrical Connections The TT31 has two Molex edge connectors one with 24 contacts which is the primary interface and a second connector with 12 contacts which carries signals to support ADS B and uplinked TIS traffic A single coaxial connector attaches to the antenna The only feature of the current TT31 that depends on the second Molex connector is the altitude ale
35. programming Verification of the reported altitude using a static tester For aircraft using parallel Gray code encoders the test should include a range of altitudes up to 6 800 feet 14 800 feet or 30 800 feet depending on the service ceiling of the aircraft these altitudes correspond to code changes which are not otherwise tested at lower altitudes Where installed verification of correct squat switch ground airborne indications In an aircraft with a squat switch setting the Mode switch to ALT when the aircraft is on the ground should leave the transponder in GND mode when the aircraft becomes airborne the mode should switch automatically to ALT Interrogations to verify the receiver sensitivity A Mode S transponder should have a minimum triggering level MTL of between 77 dBm and 71 dBm Failure to meet this requirement usually indicates antenna or coaxial cable problems Interrogations to verify the transmitted power A Class 1 installation should have no less than 125 Watts at the antenna and no more than 500 Watts Failure to meet this requirement is also generally due to antenna or wiring issues Where installed verification of the GPS position source and ADS B outputs In an aircraft with a configured GPS pressing the FUNC button on the transponder front panel in normal operation will display the ADS position monitor With the aircraft outside the hangar for good GPS reception the aircraft position should be displayed o
36. r Crimp Insulator Retaining Crimp Tab Once crimped the contacts should be slotted into the rear of the connector shell Push the contact in until the retaining tab clicks into place Tug gently to confirm the contact is locked in place The contacts can be easily removed using the Molex removal tool or equivalent This is pushed gently into the connector shell from the side opposite from the wire entry and lifts the retaining tab from the stop allowing the contact to be eased out by pulling on the wire Trig Avionics Limited Page 13 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 7 Antenna Installation The antenna should be installed according to the manufacturer s instructions The following considerations should be taken into account when siting the Antenna e The antenna should be well removed from any projections the engine s and propeller s It should also be well removed from landing gear doors access doors or others openings which will break the ground plane for the antenna e The antenna should be mounted on the bottom surface of the aircraft and in a vertical position when the aircraft is in level flight e Avoid mounting the antenna within 3 feet of the ADF sense antenna or any COMM antenna and 6 feet from the transponder to the DME antenna e Where practical plan the antenna location to keep the cable lengths as short as possible and avoid sharp bends in the cable to minimise t
37. raft zone 2 type 3 4 5 to category S level M Equipment at strike off level 3 also tested for aircraft zone 2 type 1 Helicopters to category U level G Explosion 9 0 Equipment identified as Category X no test required Waterproofness 10 0 Equipment identified as Category X no test required Fluids Susceptibility 11 0 Equipment identified as Category X no test required Sand and Dust 12 0 Equipment identified as Category X no test required Fungus 13 0 Equipment identified as Category X no test required Salt Spray 14 0 Equipment identified as Category X no test required Magnetic Effect 15 0 Equipment tested to Category Z Power Input 16 0 Equipment tested to Category B Voltage Spike 17 0 Equipment tested to Category B Audio frequency conducted susceptibility 18 0 Equipment tested to Category B Induced signal susceptibility 19 0 Equipment tested to Category A Radio frequency susceptibility 20 0 Equipment tested to Category T Radio frequency emission 21 0 Equipment tested to Category B Lightning induced transient susceptibility 22 0 Equipment identified as Category XXXX no test required Lightning direct effects 23 0 Equipment identified as Category X no test required Icing 24 0 Equipment identified as Category X no test required Electrostatic Discharge 25 0 Equipment identified as Category X no test required Trig Avionics Limited Page 29 TT31
38. repaired by unauthorised persons or in violation of Trig Avionics Limited service procedures Trig Avionics Limited assumes no responsibility for any consequential losses of any nature with respect to any products or services sold rendered or delivered Page 28 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 11 Environmental Qualification Form Nomenclature TT31 Mode S Transponder Part Number 00220 XX ETSO 20112b Manufacturer Trig Avionics Limited Address Heriot Watt Research Park Riccarton Currie Scotland EH14 4AP Conditions DO 160D Description of Conducted Tests Section Temperature and Altitude 4 0 Equipment tested to Categories A1 C1 Low temperature ground survival 4 5 1 55 C Low temperature operating 4 5 1 20 C High temperature operating 4 5 3 55 C High temperature short time operating 4 5 2 70 C High temperature ground survival 4 5 2 85 C Loss of Cooling 4 5 4 Cooling air not required 70 C operating without cooling air Altitude 4 6 1 35 000 feet Decompression 4 6 2 8 000 to 35 000 feet in 15 seconds Overpressure 4 6 3 15000 feet Temperature Variation 5 0 Equipment tested to Category C Humidity 6 0 Equipment tested to Category A Operational Shocks 7 2 Equipment tested to Category B Crash Safety 7 3 Equipment tested to Category B and extended to use test levels for Helicopters Vibration 8 0 Airc
39. rter In simple installations it is therefore possible to omit wiring for the second connector altogether The Molex edge connector used in the TT31 is similar to the connector used on the KT76A and KT78A transponders and the common signals on the primary connector use the same contact positions and are electrically compatible The antenna connector is also compatible Providing that the wiring is appropriately installed it is intended that you can upgrade a KT76A or KT78A installation to the TT31 without any connector rewiring Before doing that however you MUST check that the wiring for the existing transponder is in good condition Page 8 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 4 1 Primary Interface Pinout Pin Signal Direction Ground E Lighting 14V Input Lighting 28V Suppress I O Bi directional Squat Switch In Serial Alt Out Serial Alt In Altitude D4 Suppress In Standby Switch 11 33V DC ee 11 33V DC hee Ground El Altitude B4 Altitude B2 Altitude C1 Altitude B1 Ident Switch In Altitude C4 Altitude A4 Altitude A2 Altitude C2 Altitude Al N Do Not Connect These signals are different to the KT76A KT78A pinout on the KT76A and KT78A these signals are not usually connected in the aircraft a oroma 2 Lighting av la Lighting 28v a Suppress vo 5 Squat SwitehIn 6 Seriaramom 7 Seran Alta s Amwdepa
40. sable lengths of some common cable types Actual cable loss varies between manufacturers there are many variants and the table is therefore based on typical data Use it as a guide only and refer to the manufacturer s data sheet for your specific chosen cable for accurate values Max Length Max Length Insertion Loss MIL C 17 Cables Electronic Cable in Metres in Feet dB metre at Specialists Type 1090MHz 2 54 8 4 0 59 M17 128 RG400 3 16 10 4 0 47 3C142B 3 81 12 6 0 39 M17 112 RG304 Page 14 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 25 17 3 0 29 M17 127 RG393 311601 6 42 21 1 0 23 311501 8 22 26 11 0 18 311201 12 59 41 3 0 12 310801 Contact Electronic Cable Specialists on 1 414 421 5300 or www ecsdirect com for their data sheets When routing the cable ensure that you e Route the cable away from sources of heat e Route the cable away from potential interference sources such as ignition wiring 400Hz generators fluorescent lighting and electric motors e Allow a minimum separation of 300mm 12 inches from an ADF antenna cable e Keep the cable run as short as possible e Avoid routing the cable round tight bends e Avoid kinking the cable even temporarily during installation e Secure the cable so that it cannot interfere with other systems Trig Avionics Limited
41. so provides access to the ADS B position monitor VFR Pressing the VFR button sets the transponder to the pre programmed conspicuity code Pressing the button again restores the previous squawk code FLT SQ Pressing FLT SQ alternates the primary display between squawk code and Flight ID ENT The ENT button enters a digit in the code selector BACK The BACK button goes back to the previous digit in the code selector 8 5 Code Selector Knob The right hand knob is used to set squawk codes and the Flight ID The FLT SQ button selects which will be updated Turning the knob will highlight the first digit on the display and the digit can be changed as required Press the ENT button to advance to the next digit When ENT is pressed on the last digit the new squawk code or Flight ID will replace the previous value If the code entry is not completed within 7 seconds the changes are ignored and the previous code restored 1200 VFR code in the USA 7000 VFR code commonly used in Europe 7500 Hijack code 7600 Loss of communications 7700 Emergency code The Flight ID should correspond to the aircraft call sign entered on your flight plan If no flight plan is active the aircraft registration should be used as your Flight ID Use only letters and digits If the Flight ID is less than 8 characters long entering a blank character will end it 8 6 Flight Timer The Flight Timer records the time for which the transponder has been powered on and
42. sponsibility of those desiring to install this transponder on or within a specific type or class of aircraft to determine that the aircraft operating conditions are within the TSO standards The transponder may be installed only if further evaluation by the user installer documents an acceptable installation that is approved by the appropriate airworthiness authority 3 4 Non TSO Functions The TT31 Mode S Transponder contains the following non TSO functions e Stopwatch and Flight Timer The transponder provides a simple stopwatch and flight timer function displayed on the front panel e Altitude Monitor The Altitude Monitor activates an audio annunciator or annunciator light depending on installation when the aircraft pressure altitude differs from the previously selected altitude by more than 200 feet e Altitude Repeater This is a serial altitude output that can connect to a GPS or other device needing serial altitude data this allows the transponder to act as a repeater for the altitude input instead of requiring a second altitude encoder The operation of each of these functions is described later in this manual The non TSO functions defined in this section are not part of the TSO approval The non TSO function data included in this section is approved under 14 CFR 21 305 d Trig Avionics Limited Page 5 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 4 Unit and Accessories supplied 4 1 TT31
43. st closely matches the aircraft the transponder is installed in 6 1 6 Squat Switch Source The Squat switch input allows the transponder to automatically switch between Airborne and Ground modes and to automatically start and stop the flight timer The sense of the squat switch input can be selected using the rotary knob If the squat switch input is not connected the Not Connected option must be selected 6 1 7 TIS Output If the aircraft has a Traffic Information Service TIS compatible display connected to the transponder select the appropriate interface protocol using the rotary knob Note TIS is a Mode S uplink service that is provided by some US approach radars TIS coverage is limited to the coverage areas of those radars there is no TIS provision outside the USA 6 1 8 GPS Input If a GPS is connected for ADS B position reporting select the appropriate interface protocol using the rotary knob 6 1 9 GPS TIS Line Speed If a GPS input or TIS output has been configured you should select the appropriate line speed using the rotary knob Traffic displays using the Garmin protocol run at 9600 bps Panel mount GPS units with Aviation format outputs generally also run at 9600 bps NMEA GPS units generally run at 4800 bps Freeflight 1201 and NexNav 3101 GPS receivers generally run at 19200 bps Note The TIS output and GPS input speeds are not separately controlled on the TT31 Not all combinations of GPS input and TIS ou
44. such as ADS B It is however crucial to the reliable operation of the system that each aircraft has a distinct Mode S address The Mode S address is allocated by the registration authority for the aircraft and must be set when the TT31 is installed 2 2 Interfaces At the rear the transponder has two Molex style connectors and a single antenna connector for blind mating with the corresponding connectors in the mounting tray The interfaces provide the following services Parallel altitude input Serial altitude input Serial altitude output Ident input Standby input On ground input Lighting bus input DME Suppression Input Suppression bus I O Audio output Audio mute input Altitude alert output GPS Input Page 2 Connection to an external altitude encoder using parallel Gray code Connection to an external RS232 altitude encoder Using serial altitude data allows the transponder to report altitude with 25 foot resolution Connection to a GPS or other device needing serial altitude data this allows the transponder to act as a repeater instead of requiring a second altitude encoder External IDENT switch input External standby input for dual transponder installations Allows automatic flight ground mode switching for aircraft with a squat switch Used to adjust the backlight and switch lighting intensity Input to limit interference between DME interrogations and transponder replies suppresses
45. tput will be usable if the external devices operate on fixed bit rates and are different to each other 6 1 10 GPS System Certification Level An important metric for ADS B ground system behaviour is the SDA or System Design Assurance level It is intended to reflect the probability that the GPS position source is providing erroneous information and is based on the certification standard that was used by the GPS vendor This will be indicated in the form of a letter code A to D on the data plate or installation documentation for the GPS in accordance with the standards DO 178B and DO 254 for example DO 178B level C If Page 20 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM both standards are reported but at different levels use the lower standard higher letter 6 1 11 GPS NACy Another metric that the ADS B ground system uses to help it track the aircraft is NACv NACv is the Navigational Accuracy Category for velocity and is a design feature of the GPS receiver It represents the error bound for velocity that the GPS may report in acceleration deceleration or turning manoeuvres You can find this information from your GPS installation manual 6 1 12 Aircraft Length and Width On the ground ADS B transmits encoded aircraft size information which is used by ATC to identify taxiing routes and potential conflicts When configured for ADS B the TT31 will ask for the aircraft length a
46. transponder whilst active ARINC compatible suppression bus signal used in aircraft with more sophisticated suppression needs both an input to and output from the transponder Optionally used by the altitude monitor function Toggle function to mute the audio output Output used to signal altitude deviations when optional altitude monitor function is used Connection to a GPS supplying position input for ADS B position reporting Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM TIS Output RS232 output for connection to traffic display Trig Avionics Limited Page 3 TT31 Transponder Installation Manual 00455 00 27 March 2012 Issue AM 3 Technical Specifications 3 1 Regulatory Specification Compliance FCC Identification Applicable documents Software Power Requirements Altitude Humidity Operating Temperature Transmitter Frequency Transmitter Power Transmitter Modulation Receiver Frequency Receiver Sensitivity Characteristics ETSO 2C112b TSO C112 Class 1 Level 2es ETSO Cl66a TSO C166b Class BIS VZI00220 EUROCAE ED 73B EUROCAE ED 14D RTCA DO 160D EUROCAE ED 14E RTCA DO 160E RTCA DO 181C RTCA DO 260B ED 12B RTCA DO 178B Level B 10 33 Volts DC Typical 6 3Watts 14Volts 35 000 feet 95 50C for 6 hours 85 38C for 16 hours Tested to Category A in DO 160D 20C to 55C 1090MHz 1MHz 240 Watts nominal 1
47. uired cables Guidance on cable types is Page 6 Trig Avionics Limited TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM given in section 5 below e Fixings To secure the transponder tray to the airframe you will need at least 6 flat head screws and six self locking nuts If the aircraft does not have existing mounting provisions you may need to fabricate additional brackets to support the transponder tray To support the optional ADS B features a GPS receiver with an appropriate serial output is required To support the optional TIS features a display with an appropriate serial input is required Trig Avionics Limited Page 7 TT31 Transponder Installation Manual 27 March 2012 00455 00 Issue AM 5 Installation 5 1 Unpacking and Inspecting Equipment Carefully unpack the transponder and make a visual inspection of the unit for evidence of any damage incurred during shipment If the unit is damaged notify the shipping company to file a claim for the damage To justify your claim save the original shipping container and all packaging materials 5 2 Mounting The TT31 Mode S transponder must be mounted rigidly in the aircraft panel The following installation procedure should be followed remembering to allow adequate space for installation of cables and connectors e Select a position in the panel that is not too close to any high external heat source The TT31 is not a significant heat source itself and d
48. witching on the transponder and the setup system will run The script will prompt for the following configuration items e Mode S Address e VER Squawk Code e VFR Flight ID Registration e Aircraft Maximum Airspeed e Aircraft Category e Squat switch source if fitted e GPS position source if fitted and ADS B parameters s TIS output format if used e Audio Output Volume e LCD Dimming Settings It will then run some simple installation diagnostics including an external interface check a check of the altitude encoder interface and a check of the lighting bus input All the programming is accomplished using the right hand rotary knob and the ENT BACK and FUNC buttons Make all input selections using the rotary knob Pressing the ENT button accepts the current input and advances to the next input item Pressing the BACK button allows you to change something you have already entered Pressing the FUNC button moves directly to the next screen 6 1 Configuration Items 6 1 1 Aircraft Address Programming The Mode S Address is a 24 bit number issued to the aircraft by the registration authority for the aircraft These addresses are usually written as a 6 digit hexadecimal number although you may also encounter one written as an 8 digit octal number The TT31 only understands the hexadecimal format so you must first convert an octal number to hexadecimal Enter the 6 digit aircraft address using the rotary knob and the ENT button 6 1
Download Pdf Manuals
Related Search