USER & INSTALLATION MANUAL
Contents
1. 5 Using a cloth hold the new light bulb and push securely into light socket 6 Return halogen light glass cover to the housing 7 Turn range hood ON to test light 13 SPECIFICATIONS MODEL SIZE KH 300 30 KH360 36 INPUT POWER 260W including the light VOLTAGE AMPERE 110 120V 60Hz 2 1A CONTROLS Electronic Control LIGHTING 12V 2x20W HALOGEN LIGHTS HOOD DIMENSION W x H x D KH 300 29 8 X 24 1 14 3 KH 360 36 X 24 1 14 3 WEIGHT lbs Net Gross KH 300 46 55 KH 360 55 64 SPEED Low Medium High Air Capacity cfm KH 300 KH 360 460 550 660 HOOD DIMENSIONS KH 300 8 3 9 0 14 ve F eT KH 360 ELECTRICAL DIAGRAMS Motor i TRANSFORMER YELLOW Switch cu ET TROUBLESHOOTING If you encounter any abnormal behavior try to troubleshoot it using the following instructions below Problem Solution Check whether the power is connected or not If it is connected check The unit does not turn on whether other lamps or home appliances which link to the socket are on or not Check the installation of the range hood and tighten the mounting base The range hood vibrates shakes when Check whether the ventilation door is completely open or not operating Check whether there is blockage within the exhaust pipe Check the oil screen If the oil screen hasn t been cleaned or changed in a long time it might be blocked by oil affecting the air exh2. THE FAN WHILE THE FAN IS OPERATING Cleaning Hood Surface 1 Use only mild soap or detergent solutions Dry surfaces using a soft cloth 2 If the stainless steel hood looks splotchy use a stainless steel cleaner to clean the surface of the hood Avoid getting cleaning solution onto or into the control panel Follow the directions of the stainless steel cleaner Caution Do not leave on too long as this may cause damage to the hood finish Use a soft towel to wipe off the cleaning solution gently rub off any stubborn spots Use a dry soft towel to dry the hood 3 DO NOT allow deposits to accumulate or remain on the hood 4 DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface 12 How to Clean the Baffle Filter The spring bracing in figure 9 firmly supports the oil screen on the hood Refer to figure 10 to remove the oil screen gently Use a sponge and warm soapy water to wash it and make sure it is completely dry before putting it back Figure 9 Figure 10 How to Replace the Light Bulb CAUTION HALOGEN LIGHT UNIT MAY BE HOT WAIT UNTIL THE UNIT IS COOL 1 Make sure all controls are off and the range hood is unplugged 2 Place a flat headed screwdriver into the groove of the halogen light glass covering and the housing 3 Pop out the halogen light glass covering 4 Gently pull out the defective light bulb and discard Light bulbs should be 12V 20W maximum
3. Kruger USER amp INSTALLATION MANUAL MODEL S KH 300 KH 360 CAREFULLY READ THIS USER MANUAL BEFORE USING CONTENTS READ AND SAVE THESE INSTRUCTION cc ceeeeeeeeeeeeeeeeeeeeeeaeeeeeeeeees 3 INSTAEEA HON EE 5 OPERATION UNENEE a hae ianatnnmemeeeies 11 SPECIFICATION EE 14 AOOD IMENSIONS E 14 ELECTRICAL DIAGRAMS iridtatwaviaiand teat a RTE 15 ROOM EOIN E 16 IMPORTANT SAFETY INSTRUCTIONS A WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE OBSERVE THE FOLLOWING To Reduce The Risk Of Fire Or Electric Shock Do Not Use This Fan With Any Solid State Speed Control Device 1 Installation work and electrical wiring must be done by a qualified person s in accordance with all applicable codes and standards including fire rated construction codes and standards 2 When cutting or drilling into a wall or ceiling be careful not to damage hidden electrical wiring and other utilities 3 Before servicing or cleaning the unit switch power off at the service panel and lock the service disconnection to prevent power from being switched on accidentally When the service disconnection cannot be locked securely fasten a prominent warning device such as a tag to the service panel 4 Don t get the power lines restructured stretched connected imposed with weights or pinched etc The power lines can be easily damaged leading to electrical shock or fire 5 It is prohibited to change the
4. aust Make sure the distance between the range hood and the cooking area is The range hood does not exhaust air properly 27 30 while an island range hood should be 30 36 inches Check whether there is blockage in the exhaust pipe Make sure the size of the exhaust pipe is appropriate for the range hood The power light is on but the Try switching the range hood on and off If it still doesn t work it may be motor does not work the fault of the motor or the operating system Check whether the light bulb is properly installed The motor is running but the power light does not work Try the light bulb in a working light bulb holder if the light bulb still doesn t work replace the bulb Notice Make sure the power supply to the range hood is cut off when operating The connection of the exhaust pipe isn t air tight Check the installation of the pipes Cold air gets into the house Check whether the ventilation door is installed and whether there is clamping stagnation in the installation site that makes the ventilation door not close completely letting in cold air as a result Caution For your safety all service and inspections should be conducted by trained and qualified professionals Make sure the unit is disconnected from power supply during maintenance 16
5. cooking 5 Use high settings on cooking range ONLY when necessary 6 Do not leave cooking range unattended when cooking 7 Use this unit only in the manner intended by the manufacturer 8 Before servicing switch power off at service panel and lock service panel if possible to prevent power from switching on accidentally What to Do In The Event Of a Range Top Grease Fire e SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT e NEVER PICK UP A FLAMING PAN You may get burned e DO NOT USE WATER including wet dishcloths or towels to extinguish a grease fire a violent steam explosion will result e Use a fire extinguisher ONLY if a You know you have a Class ABC extinguisher and you already know how to operate it b The fire is small and contained in the area where it started c You have already called the fire department d You can fight the fire with your back to an exit Based on kitchen fire safety tips published by NFPA CAUTION Important Observe all governing codes and ordinances For general ventilating use only Do not use to exhaust hazardous or explosive materials and vapors Do not run cord under carpeting Do not cover cord with throw rugs runners or any other coverings Do not route cord under furniture or appliances Arrange
6. cord away from high traffic areas and so it will not be tripped over Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society of Heating Refrigeration and Air Conditioning Engineers ASHRAE and your local code authorities To reduce the risk of fire use only metal ductwork Do not let children use the hood unattended The temperature of the environment for range hood use should not be higher than 40 C 4 INSTALLATION Unplug the appliance from the power supply before servicing NOTE This procedure will require 2 people for easier installation Please read all instructions carefully before installing 1 Ifyou are renovating your kitchen be careful to protect your range hood Volatile gases from building materials dust paint and coatings can corrode and tarnish the surface of your range hood Instead install your range hood after your kitchen renovation is complete 2 The stainless steel may have very sharp edges wear protective gloves when removing the range hood for installing cleaning or servicing 3 Be careful not to damage any hidden wire sets when drilling into a wall Unplug the range hood from the power supply before installation the main power box should be switched off 4 If it is needed to move the gas stove before installing the range hood switch off the gas valve entirely bef
7. increase or decrease with a range from 00 to 59 After setting the correct time wait for eight seconds or press the key to exit This function cannot be set while the motor is running On the control panel press xt to turn the light on Press xt again to turn the light off Se When the motor is running the Ze button will light up The default wind speed is high pies oe to decrease the power setting by one level The wind speed is a cyclic system Pressing Ze will change the wind speed under the delay off condition On the control panel press to turn on the range hood and start the motor Press again to set the range hood into a three minute delay off 11 CARE AND MAINTENANCE A WARNING UNPLUG THE APPLIANCE FROM THE POWER SUPPLY BEFORE SERVICING There may be a risk of fire if you do not clean the hood according to the instruction guide Protect the motor keys and other electrical components of the hood from water during cleaning DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods of time Many of these compounds contain chemicals which may be harmful to the surface of the range hood Rinse with water after exposure and wipe dry with a clean lint free cloth For optimal operation clean range hood and all baffle spacer filter oil tunnel oil containers regularly A SAFETY WARNING NEVER PUT YOUR HAND INTO THE AREA HOUSING
8. internal wiring of the range hoods without authorization it may result in abnormal functioning which may lead to personal injury Improper maintenance may lead to electric shock and fire Ducted fans must always be vented to the outdoors Clean all grease laden surfaces frequently To reduce the risk of fire and to disperse air properly make sure to vent air outside DO NOT vent exhaust air into wall spaces attics crawl spaces or garages NOTE If there is no invoice issued by the authorized agency or the damage of the components is due to misuse improper installation improper use improper handling negligence or other uncontrollable factors by our authorized agency warranty services cannot be obtained Any maintenance done without the consent of our authorized agency will make the warranty card invalid For any direct or indirect damage caused by our product such as personal property real property loss and personal injury due to the above mentioned misuse reasons our company will not be liable AA WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE 1 Never leave surface units unattended at high settings Boil overs cause smoke and grease spills may ignite Heat oils slowly on low or medium settings 2 Clean ventilation fans frequently Grease should not be allowed to accumulate on the fan or filter 3 Use proper pan sizes Always use cookware appropriate for the size of the surface element 4 Always use ventilation when
9. ll an outlet near the appliance e The farthest distance between the power line and the power socket should be no more than 59 Make sure the power line has a reliable power supply system refer to figure 8 e After installation range hood is ready for use Figure 8 Important the power cord should be replaced by professionals if damaged A GROUNDING INSTRUCTIONS This appliance must be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This appliance is equipped with a cord with a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly installed and grounded 10 OPERATION INSTRUCTIONS MODEL KH 300 KH 360 The range hood has three different power settings with a 3 minute delay off feature and two 12 volt 20 watt halogen lights The electronic control panel has four function keys clock lights fan speed and power control on off The extra bright LCD display screen shows the operation state at any time clearly iz D To set the time ea xt Ze these three pilot lights will turn on the LCD clock will flicker with eight seconds to set the hour Press xt or Sen and the time will increase or decrease with a range from 00 to 23 After setting the correct hour press the key within eight seconds the LCD clock will flicker Press xt or Sen and the minutes will
10. ore moving the gas stove 5 Always use a power socket with reliable grounding Half way links of the power line the use of extension cords and multi port wiring devices may lead to electric shock plugs and sockets overheating and fire Make sure the operation is done by professional electricians and strictly abide by the national and local electric laws and regulations Switch the power off and take measures to prevent the power switch from automatically tripping before wiring 6 To ensure a safe and smooth installation use our accessories for installation and make sure the expansion tube stays closely within the wall hole when installing it Do not make the drill hole too large doing so will cause the expansion tube to be loose which may result in accidental damage 7 Try to make the two sides of the range hood balanced when installing 8 If there are no abnormal occurrences during a qualified test run after installation read the instruction manual carefully and keep it in a safe place The following tools and materials are needed to finish the installation e Electric drill e Drill bit e Cross head screwdriver e Flat head screwdriver e Pencil and ruler to mark the position for installation Pre Installation Calculations Stand alone installation table 1 A Height of Floor to Counter Top Standard 36 B Preferred Height of Counter Top to Hood Bottom Recommended 2777 30 C Height of Hood D Height of Dus
11. rk four mounting holes and two security holes on the mounting surface of the hood then drill Firmly embed the expansion pipe refer to figure 3 2 Use across screwdriver to screw in 4 mounting screws Note the distance between the wall and screw is 10mm refer to figure 4 3 Hang the hood onto the installed screws with precise alignment to the mounting hole of the hood 4 Install the hood firmly onto the wall by tightening the four mounting hole screws 5 For safety it is necessary to drill in screws in the two security holes and make sure they are tightened Figure 4 Note make sure the hood has been installed firmly before letting go Piping system installation IMPORTANT TO REDUCE THE RISK OF FIRE USE ONLY METAL DUCTWORK 1 Attach the duct outlet to the range hood Aluminum or Steel Pipe 2 Attach the exhaust pipe to the duct outlet and use Duct Tape duct tape to firmly seal all the joints Air Outlet 3 If you are equipped with a chimney install the chimney according to figure 7 Power source needs to be within 1 5m to the unit Power Connection WARNING Improper grounding can result in the risk of electric shock Consult a qualified electrician if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded Do not use an extension cord If the power supply cord is too short have a qualified electrician insta
12. t Cover E Height of the Hood Installation F Height of Floor to Ceiling AA SAFETY WARNING THE HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES WHEN REMOVING ANY PARTS FOR INSTALLING CLEANING OR SERVICING Preparation before Installation NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING Determine the installation height of the range hood refer to figure 1 Gos G scker Ga te Lelio belaht If there is a gas stove under the range hood the minimum distance between the cooking area and the hood should be 30 If there is an electric stove under the range hood the minimum distance should be 24 to 30 Figure 1 e Determine the location of the exhaust pipe which discharges to the outside Refer to figure 2 A linear and short air outlet can make the range hood work more smoothly e Avoid using too long and too bent of an exhaust pipe the use of these pipes can affect the performance of the hood and even shorten the service life e Use duct tape to firmly seal the joints of the pipe make sure the exhaust pipe and the vent outlet are firmly connected Mounting holes Figure 3 Figure 2 Equipment installation e It is necessary to do turn on the range hood and do a test run to make sure it is working normally e Remove all protective film on the hood before installation 1 By using the reference of Figure 1 and the measured values on page 14 15 ma
Download Pdf Manuals
Related Search