Simon ><Ti User Manual - Johns Brothers Security
Contents
1. Version Event History The panel will keep a history of the most recent 40 events Press Show next to Event History to see them listed chronologically with the newest event at the top of the list Note If a appears in the Event History list the event was not sent to the central station Direct Bypass The panel will allow learned in sensors that are actively armed to be bypassed so that they will not cause an alarm when the panel is armed Press Select next to Direct Bypass and provide a valid access code to access this menu The list shows all of your sensors with their current state bypassed or not bypassed press the state to change it Panel Status Press the Listen next to Panel Status to have the panel speak the current status of the panel If the icon appears a trouble condition has occurred Press Clear to clear certain panel status messages Chime To enable or disable the chime feature 1 Enter the Status amp Settings menu and scroll to the Chime option 2 Press On or Off to modify the setting a gold icon indicates the option is selected 3 Press Close to exit the Status Settings menu Simon XTi User Manual 23 Note This menu option will not appear if chime sensors are not in your system Special chime To enable or disable the special chime feature 1 Enter the Status amp Settings menu and scroll to the Special Chime option 2 Press On or Off to modify the setting a gold icon in2. Sensor Instructions Minimum packets required Hardwire contact Door window Carbon monoxide alarm a Glassbreak a Motion sensor Smoke Key fob Simon XTi User Manual Open the hardwire contact Open the secured door or window Press and hold the Test Hush button approximately 5 seconds until the unit beeps two times and then release the button Test with an appropriate glass break sensor tester Avoid the motion sensor field of view for 5 minutes and then enter its view Press and hold the test button until the system sounds transmission beeps Press and hold the Lock and Unlock buttons simultaneously for 3 seconds 1 6 of 8 6 of 8 6 of 8 6 of 8 6 of 8 6 of 8 31 Sensor Instructions Minimum packets required Simon XT talking For sensor testing a 1 0 touch screen press and hold the 60f8 touch screen Y Emergency icon for 5 seconds For sensor testing a 1 1 or greater touch screen press the Settings gear icon scroll down and then press the RF Test icon a Not investigated for use by UL Note Refer to specific sensor installation instructions for complete operation and testing details Sensor testing notes e Conduct sensor test in all possible environmental conditions for example interior doors open and closed HVAC system on and off wireless music system turned on and off e Conduct sensor test whenever changes are made to the installation enviro
3. To enter programming mode Note Programming mode can only be entered if the system is disarmed 1 Enter the Status amp Settings menu 2 Scroll until Programming is listed press the Enter icon 3 Enter your master code and then press OK Note You have four seconds between number presses to enter the code or you will be returned to the home screen At this point you are in the Programming menu At this level the following submenus are accessible e Access Codes e Security e Phone Numbers e Siren Options e System Tests e Interactive Services Optional Ask your dealer for more information The sections below describe the options that you can program in each of the programming submenus Simon XTi User Manual 27 Access codes There are three types of access codes Master code The master code is your most powerful code and can be used for all user operations including programming The initial value of the master code is 123 1234 12345 or 123456 depending on the installer programmed access code length User codes 1 to 8 There are eight user codes which can be used for many user operations but not programming or bypassing sensors Initially all user codes are blank A user code can be deleted by pressing Delete while the code is being changed Duress code The duress code when used in place of another user code generates a silent duress alarm that is reported to the central monitoring station Initially th
4. walls roofs or areas blocked by a closed door Sensors may not detect smoke in other levels of the building Sensors may not warn in time when fires are caused by smoking in bed explosions improper storage of flammables overloaded electrical circuits or other hazardous conditions e f telephone lines are out of service Inadequate maintenance is the most common cause of alarm failure Therefore test your system at least once per week to be sure sensors sirens and phone communication are all working correctly Although having an alarm system may make you eligible for reduced insurance premiums the system is no substitute for insurance WARNING Security system devices cannot compensate you for the loss of life or property 34 Simon XTi User Manual Emergency planning Since an emergency is always unexpected you should develop plans to help prepare for a variety of emergencies Periodically discuss and rehearse emergency plans to include the following Understand how to use your security system Know the normal state of doors and windows open closed or locked Escape fast Do not stop to pack Use a different escape route if closed doors feel hot to the touch Crawl and hold your breath as much as possible to help reduce smoke inhalation during your escape Meet at a designated outdoor location Emphasize that no one should return to the premises if there is a fire Notify the fire department from a neighbor s ph
5. 1175C 910CSIXT Ringer Equivalence 0 2B Load Number 0 2 www utcfireandsecurity com or www interlogix com www interlogix com customer su pport Content ig o AAA A O 1 Using the Simon XTi security system ocococcconococoncncnnnonononnnononanacannnnononons 3 Panel CONTO Srl ASADA AAA 3 A ODOM a ee Ree ree 6 Home Sa tine 7 A oe aero nee oes RR RR ep RN 10 By DOSS INTO Se MS OM Suit rii 11 PUGS anel esta A A Dea Sele OS 12 CHIME Siune oem A AT 13 A ane o 14 Using anioftsite Phone sra aaa ici 14 RETOS a E nee een Pere 15 How your system COMMUNICARES ooocoonocconconnonconnoncnnnonononconoonnononnoos 17 E 17 A A A A 17 A cenminseaee ete 18 SUSTO CONT UIOLO jp RE a rA eE EEEE 21 Settings MENUS a Di 21 GOCE OPIO Sd ot 21 Mendaro 21 A A er ae iia nae Sits Ret reuse Sth 23 Direct eV A rt Mp E A Tn Mier Co 23 E AAA a R uni A caceee ti eitexs 23 A SC GUESS aa 23 SECO CINE rianan aaa a E E EE 24 VICE VOUTE se idea dd a a a 24 A A 24 ep e aca eRe or o a E OA 24 DETONA a sae ie irre E 25 COBROU nee 25 A OS 25 Settime Ana e e e a 26 EMI SNC Ni A apa 27 A E E 27 PROCON O qoesi esi rateio dice A id o e asia 27 A 30 Simon XTi User Manual TOA a 31 EA E AP a AAA RR Pre 31 COMES a 32 Central station COMMUNICOAtION sas a Se SYS ESRI NM Ae 33 Reference infOrmMaton iii neither chance calc 34 A anaana a E 34 Emergency PIAN NN O tt 35 Cleaning the tOUCh scr A 36 DISPOSTA ene Mes eat ST 37 Sensor and Module locations aaa t
6. amp Settings screen select Set Date Time 2 Enter master access code 3 From the Set Date Time screen press the first box to set hour and press SAVE 4 Press the second box to set minutes and press SAVE 5 Press a m p m box to toggle a m p m setting Set Date Time X CLOSE dde 12 oo am ee if fas To set the date 1 From the Set Date Time screen press the first box in the second row to set month and press SAVE 2 Press the second box to set day and press SAVE 3 Press the third box and enter the year and press SAVE 26 Simon XTi User Manual 4 Press CLOSE repeatedly to exit Emergency icon In an emergency touch the Emergency icon An Emergency screen appears See Emergency icon in Table 4 on page 5 You will see three icons Panic Police or Fire Select the appropriate icon Note If your system is connected to a security monitoring service the authorities will be notified This option may not be enabled Contact your dealer for details If you initiate an emergency alarm by mistake you can cancel the alarm by touching the red alarm icon Alarms on page 12 and entering your code within 30 seconds typical time limit contact your dealer for more information on your system configuration System tests This menu lets you run sensor and communication tests and initiate a phone call from the panel to Enterprise Downloader For more information see Testing on page 31 Programming
7. displays only on the Two Way Talking Touch Screen a These features have not been verified for use by UL Alarm sirens Exterior and interior sirens make three different alarm sounds on the premises each indicating a different type of alarm Sirens are programmed by the installer to time out and stop sounding after a specified time Simon XTi User Manual 17 Table 10 Siren sounds Function Fire Intrusion Emergency Interior and panel siren Temporal 3 Steady Fast on off Exterior siren Temporal 3 Steady Note Temporal 3 refers to a continuous pattern of three siren pulses then off for 1 5 seconds three siren pulses then off for 1 5 seconds Trouble beeps Your security system is able to automatically test itself for e Power failures e Low batteries e Sensor supervision e Communication trouble with the central monitoring station When your system detects one of the problems above six rapid beeps sound i minute until the trouble condition is corrected To stop the trouble beeps press and then press the icon or arm then disarm the system while the trouble condition exists Trouble beeps will resume 4 hours later unless the trouble condition is corrected Table 12 describes the trouble beep conditions Table 11 Trouble beep conditions Condition Description AE Power alure This condition if programmed by the installer occurs if your security system has been accidentally unplugged or if ther
8. indicated or press Bypass You will see the arming countdown message at the bottom of the screen You can press Cancel and enter your code to stop the arming process Figure 3 Pre arm screen 12 57p X CLOSE armsysteM A A Ke MOTION SENSORS ONLY AWAY ARM or DOORS amp WINDOWS ONLY ALL STAY AWAY ARM SETTINGS OPTIONAL Entry Silent delay ON OFF exit ON OFF To disarm level 1 1 Press PRESS TO DISARM 2 Enter your code when the keypad screen appears c 12 57p X CLOSE Enter Access Code The panel displays and speaks Disarmed and the panel beeps once To arm doors and windows level 2 1 Ensure that all doors and windows are closed q 2 Press Press DOORS amp WINDOWS ONLY STAY see Figure 3 above 4 Ifa code is required enter your code when the keypad screen appears The panel speaks Doors and Windows On and starts an exit delay and sounds exit beeps in groups of two until the exit delay expires To cancel arming press CANCEL ARMING on the countdown screen 8 Simon XTi User Manual CANCEL ARMING Arming In 60 To arm motion sensors level 3 a 1 Press 2 Press MOTION SENSORS ONLY AWAY see Figure 3 on page 8 3 Ifa code is required enter your code when the keypad screen appears The panel speaks Motions On starts an exit delay and sounds exit beeps in groups of three until the exit delay expires Note Depending on your configuration this
9. is sufficiently charged After the initial charge should the panel lose AC Power and experience a low battery condition the icon will appear and trouble beeps will sound unless silenced You can silence trouble beeps by e Arming or disarming the system or e Pressing the STATUS amp SETTINGS icon and pressing LISTEN next to Panel Status This will disable the sounder for 4 hours but the trouble indication will remain until the battery is recharged Contact your installer to replace your backup battery This system is intended to be checked by a qualified technician at least once every 3 years Panel controls The self contained panel provides the user interface for system operation and programming system functions Simon XTi User Manual Figure 1 Simon XTi controls a A N Y Note The touch screen in Figure 1 above is an example Your touch screen and system may be configured differently Table 3 below provides a description of the panel s graphical user interface and audio Table 3 Panel features Control Description Piezo siren Provides alarm beeps and status beeps Touch screen Provides a graphical user interface for programming and system operation Microphone Used to communicate with the central monitoring station after an alarm Speaker Provides voice output and sounds key beeps Designer template The designer template is the adhesive back
10. the settings specified by your installer Use this feature only when instructed by your installer or dealer To initiate a download 1 2 3 4 Enter the Status amp Settings menu Scroll until System Tests is listed Press Enter Enter your master code and press OK Press the System Download icon Simon XTi User Manual 33 Reference information This section provides information on system limitations emergency planning and smoke and heat detector locations It also provides a place to list your sensor and module locations and other programming values Alarm system limitations Not even the most advanced alarm system can guarantee protection against burglary fire or environmental problems All alarm systems are subject to possible compromise or failure to warn for a variety of reasons e f sirens are not placed within hearing range of persons sleeping in remote parts of the premises or if they are placed behind doors or other obstacles e f intruders gain access through unprotected points of entry or areas where sensors have been bypassed e f intruders have the technical means of bypassing jamming or disconnecting all or part of the system e f power to sensors is inadequate or disconnected e f freeze or any environmental sensors are not located in areas where the appropriate condition can be detected e If smoke does not reach a smoke sensor For example smoke sensors cannot detect smoke in chimneys
11. Simon XTi User Manual P N 466 2452 e REV A e 15MAR12 Copyright Trademarks and patents Manufacturer FCC compliance Contact information Customer support 2012 UTC Fire amp Security All rights reserved The Simon XTi name and logo are trademarks of UTC Fire Security GE and the GE monogram are trademarks of the General Electric Company and are under license to UTC Fire amp Security 9 Farm Springs Road Farmington CT 06034 4065 USA Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products UTC Fire amp Security Americas Corporation Inc 1275 Red Fox Rd Arden Hills MN 55112 6943 USA This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications FCC Part 15 registration number B4Z 910C SIMON IC 1175C 910CSIMO Part 68 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA FCC registration number US B4ZAK02B55910 Canada
12. ation on household fire warning is available at nominal cost from The National Fire Protection Association Batterymarch Park Quincy MA 02269 Request Standard No NFPA74 O Required smoke detector H Heat detector Indicates smoke detector is optional if door is not provided between basement and recreation rooms Use the following guidelines when drawing your floor plan Show all building levels Show exits from each room two per room are recommended Show the location of all security system components Show the location of any fire extinguishers Cleaning the touch screen If necessary use a soft lint free cloth to clear smudges on the touch screen do not use glass cleaner on the touch screen 36 Simon XTi User Manual Disposal Dispose of all equipment is accordance with local requirements Contact your installer for more information Sensor and module locations Use Table 15 below to list your sensor and module locations Table 15 Sensor and module locations Sensor number Sensor name Sensor type Location Example Front door Door window sensor Front door E E ESA E E e RO A N INININ IN DN Ri IR Ee Ese ese N PEB IN N P O S Q J D O0 BE A N R Oo Simon XTi User Manual 37 Sensor number Sensor name Sensor type Location 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Access codes Use Table 16 below to record you
13. blank at 2 00 am daily for 60 minutes Touch the screen to reactivate Calibration The touch screen should arrive with proper screen calibration This feature should only be used if there is a problem with your touch screen s calibration To calibrate the screen 1 From the Status amp Settings screen press SHOW next to Calibration Calibration SHOW 2 Touch the center of the cross using a soft fine point as it appears in each corner of the screen Calibration ri y center After the cross in the fourth corner bottom right is pressed the user will be returned to the Status amp Settings screen Help Press the Help icon to access a menu showing how to perform basic tasks on your Simon XTi 1 From the Status amp Setting screen press the HELP icon Help HELP Simon xTi User Manual 25 2 From the SYSTEM HELP screen choose the help topic to search LEMERGENCIA 12 57 X close SYSTEM HELP ARMING amp DISARMING SYSTEM UNDERSTANDING THE TOUCH SCREEN ADJUSTING VOLUME MISCELLANEOUS 3 Press and to scroll through help topics 4 Press CLOSE to return to the previous screen Set time and date If the panel loses both AC and battery power upon power restoral the system time will reset to midnight and the date will reset to 1 1 2000 indicating it has not been set correctly Time format is hour minute a m or p m Date format is month day year To set the time 1 From the Status
14. d trouble beeps Status beeps The panel sounds status beeps to alert you to various system events and conditions Note You may receive a different number of status beeps if you press the icons quickly Table 9 Status beeps Activity Beep response Doors Windows Motions Doors Windows and Motions Disarm Chime Special chime Trouble beeps No activity beeps Property asset management beep Y Exit delay and entry delay beeps sound two times every 5 seconds and two times per second during the last 10 seconds If silent exit is used the exit delay beeps will only sound twice when you arm and twice when the exit delay expires Exit delay and entry delay beeps sound three times every 5 seconds and three times per second during the last 10 seconds If silent exit is used the exit delay beeps will only sound three times when you arm and three times when the exit delay expires Exit delay and entry delay beeps sound four times every 5 seconds and four times per second during the last 10 seconds If silent exit is used the exit delay beeps will only sound four times when you arm and four times when the exit delay expires One beep Two beeps Three beeps Six beeps every minute Press Listen next to Panel Status to stop beeps for 4 hours Twenty beeps every minute for 5 minutes feature must be programmed by the installer The panel sounds one beep when an asset group sensor is activated information
15. dicates the option is selected 3 Press Close to exit the Status Settings menu Note This menu option will not appear if special chime sensors are not in your system Voice Volume From the Status Settings screen next to Voice Volume press the left arrow to lower the voice volume and the right arrow to raise the voice volume The bars between the arrows register the volume level No bars is off Four bars is loudest se A Beep Volume From the Status Settings screen next to Beep Volume press the left arrow to lower the beep volume and the right arrow to raise the beep volume The bars between the arrows register the volume level One bar is softest Four bars is loudest Beep lt gt Volume Brightness From the Status amp Settings screen next to Brightness press the left arrow to make the screen less bright and the right arrow to make the screen more bright The bars between the arrows register the brightness level One bar is least bright Four bars is brightest Brightness lt iiil gt 24 Simon XTi User Manual Default Screen From the Status Settings screen press MAIN or BLANK next to Default Screen To make options visible on a blank screen touch anywhere on the screen The screen will stay visible for two minutes before returning to blank mode if untouched The green AC power icon will blink when in BLANK mode Default Screen MAIN BLANK Note The touch screen will automatically
16. e duress code is blank The duress code can be deleted by pressing Delete while the code is being changed To add edit access codes 1 From the Programming screen press ACCESS CODES 2 To add or edit an access code press the white field next to the access code 3 Enter the new edited code on the numbered keypad and press SAVE 4 Press CLOSE repeatedly to exit menus Security The Security menu contains the Downloader Enable option This option determines whether your dealer can access the system remotely To program the download enable option 1 From the Programming screen press SECURITY 2 Press the Security icon 3 To turn on an option press L To turn off an option press M Note M indicates the option is turned on 4 Press CLOSE repeatedly to exit menus Phone numbers Phone number 4 is the only system phone number that you can change Therefore it is often used for voice reporting alarms to your phone and can be programmed for this purpose by the installer Note Certain system options must be programmed by the installer for voice reporting alarms to work properly 28 Simon XTi User Manual To add edit phone number 4 1 From the Programming screen press PHONE NUMBERS 2 To add or edit a phone number press the white field next to the Phone Number 4 3 Enter the new edited phone number on the numbered keypad and press SAVE To delete a phone number press DELETE 4 Press CLOSE repeatedly to exit m
17. e has been an AC power outage The Ba icon will appear in the top left corner of the screen display and trouble beeps start after 5 minutes If AC power is not restored within a programmed period of time 5 to 254 minutes the system will call the central monitoring station The backup battery if fully charged will last for 18 to 24 hours depending on the load applied to the panel with no AC power In a UL Installation a new fully charged battery will last 24 hours with the panel in normal standby condition and still sound an alarm 18 Simon XTi User Manual Condition Description System battery failure Restoration of power Sensor failure Sensor low battery Failure to communicate Sensor open Simon XTi User Manual This condition occurs if the eme cy backup battery has failed Trouble beeps will start and the il icon will appear in the top left corner of the STATUS amp SETTINGS screen If your AC power is not working your security system will shut down once the battery has failed If the condition does not clear after AC power has been restored and 24 hours have passed call your security system dealer This condition occurs after a complete loss of power AC and battery When power is restored the panel will return to the arming state with the same zones bypassed it had prior to losing power This condition occurs if a sensor is not communicating with the panel Trouble beeps will start You may need t
18. ed plastic template that covers the front of the Simon XTi panel Caution The designer template and its installation are integral parts to the reliability of the system Contact your security system installer to replace the designer template Main touch screen display While the panel is idle the screen displays 4 Simon XTi User Manual Table 4 Main screen icons EMERGENCY Time va M CECERECEE gt Access the emergency screen to select the appropriate emergency icon Panic Police or Firel The current system time Depicts the status of the AC power and backup battery A red power cord represents loss of AC power to the system A green power cord icon represents AC power to the system A red battery icon represents battery low A green battery icon represents a fully charged battery Note These icons only appear in red on the main screen if the backup battery is not fully charged or the AC power is not working correctly It is recommended that the backup battery be replaced every 3 5 years Contact your installer to replace the backup battery This yellow triangle indicates faults within the system Depicts monitored door status A green check indicates all monitored doors are closed A red exclamation point indicates one or more doors are open N A indicates your system is not configured to support door sensors Depicts monitored window status A green check indicates all monitored windows are closed A red exc
19. enus Sirens options The panel has two built in sound sources a piezo siren and a speaker The piezo siren makes alarm beeps and status beeps Fire and intrusion alarm beeps are always played at high volume while the volume of status beeps such as trouble or chime beeps entry and exit delay beeps or emergency alarm beeps is controlled by the Beep Volume in the Status and Settings screen The speaker emits the panel s voice and sounds beeps when a key is pressed The siren volume is also programmable The siren and built in speaker options consist of the following Panel piezo beeps Status beeps sounded on the siren This option determines whether the panel sounds nonalarm beeps To program piezo beeps 1 From the Programming screen press SIREN OPTIONS 2 To turn on panel piezo beeps press LJ To turn off press M Note MJ indicates the panel piezo beeps are turned on 3 Press CLOSE repeatedly to exit menus Panel voice Spoken phrases on the speaker and key press sounds from the speaker heard while controlling the system This option determines whether the panel speaks status messages and arming level changes To program panel voice 1 From the Programming screen press SIREN OPTIONS 2 To turn on panel voice press LJ To turn off press M Note M indicates the panel voice is turned on 3 Press CLOSE repeatedly to exit menus Panel piezo alarms Loud alarms on the siren This option determines whether the panel so
20. evel of authority is required to perform an action These codes allow you to activate system options customize panel operations and generate a silent alarm The default code is based on the code length 3 4 5 or 6 digit code determined at installation The code types are listed in Table 12 below Table 12 Code types Code Description Master code The master code is the main code used for panel operations The default code will be 123 1234 12345 or 123456 depending on the value set by the installer for code length User codes 1 through 8 These eight codes are supplemental user codes You can use these codes for panel operations such as disarming but not programming These codes can be any 3 4 5 or 6 digits depending on the code length Duress code Use the duress code to generate a silent duress alarm while disarming Note Any combination of invalid codes in excess of 40 key presses such as fourteen invalid three digit codes will cause a system access alarm The alarm locks all touchpads except key fobs for 90 seconds Menu navigation Each menu contains a list of options and or submenus Changing screens and navigating menus is accomplished by using the various on screen interactive icons When accessing menus such as Programming or System Tests the panel prompts you to enter an access code To continue enter your master code on the keypad and then press OK A gold icon indicates an option is selected Si
21. ey fob Press and hold Lock and Unlock for 3 seconds Control Panel Enter the Status Settings screen and press the Listen icon by Panel Status Telephone Press 0 Control panel Enter the Status amp Settings menu and scroll to Chime or Special Chime press On or Off to set the value Control panel Enter the Status amp Settings menu scroll to Direct Bypass Press ENTER enter your master code scroll to the sensor and then press BYPASSED or NOT BYPASSED to set the value Simon XTi User Manual 39
22. he chime option will not appear in the System menu Voice chime Your installer may have programmed the system to speak the sensor name or make a custom chime sound when a chime sensor is tripped The chime sound if programmed will be played in place of the standard chime beeps Simon XTi User Manual 13 Special chime The special chime feature allows you to install motion sensors in a patio or at the front door and be notified when someone is approaching those areas These motion sensors are not used for intrusion protection The panel will chime three times if the special chime mode is enabled Note If there are no special chime sensors in your system the special chime option will not appear in the System menu System status Press E and then press next to Panel Status no code is required to cause the system to speak the following types of information e Alarm conditions e Alarm history e Trouble conditions e Open sensors e Bypassed sensors o LISTEN BR nii The icon and GA icon have a A when an abnormal condition such as a trouble sensor exists in the system You can clear certain status entries from the system such as old alarm history by listening to the message or by pressing Clear next to Panel Status in the Status Settings screen Using an offsite phone This feature has not been verified for use by UL If enabled by the installer you can control your Simon XTi system remotely from an offsite phone T
23. he panel answers a phone call according to the dialing method programmed by your installer After a certain combination of rings and pauses the panel will answer the call with the voice prompt Enter Your Code You must enter the correct code to gain access If you are interacting with your panel and the panel hangs up on you the system is calling in a report to the central monitoring station or remote phone due to an action by you or someone at the security system site The actions listed in Table 7 below may be performed from an offsite phone Table 7 Phone controls Action Phone key presses Comments Disarm 1 System not already disarmed 14 Simon XTi User Manual Action Phone key presses Comments Arm doors and windows 2 Press 2 again to activate the no delay feature Arm motion sensors 3 Arm doors windows and 2 3 motion sensors Listen in to house 5 to listen in to the house When in this mode the user cannot Once in listen in to house the re enter the previous menu You following options are available must hang up and call back in to e Oor1tospeak the panel to perform additional e 30or6to listen functions e 7 to extend call Check status 0 Hang up 9 Key fobs Touchpads are used to control the security system from any location within or near your home Key fob If your installer programmed the key fob with no entry delay and you arm the system with the key fob you must disarm your system before e
24. ii 37 Access eodeSTaniaranerma nie tito 38 BIAS NEE O I TEE E E O o 38 Simon XTi system quick reference s ss sssssissssiissseiisssriissssrrisssrissssrrssrnrsss 39 Simon XTi User Manual Introduction The Simon XTi uses wireless technology to warn your family about intrusion carbon monoxide and fire The system communicates with a central monitoring station and sends voice messages to an offsite phone The security system uses sensors that communicate alarms to the control panel using radio waves The system is supervised meaning that the panel checks the status of each sensor to detect problems If the panel detects trouble it will notify you with displayed and spoken messages beeps and indicator lights A Simon XTi installation may include any of the devices listed in Table 1 below Table 1 Simon XTi system components Component Type Description Control panel Operates and programs your security system It communicates to you through displayed and spoken messages The panel can communicate to a central monitoring station and send voice messages to your offsite phone Touchpads Simon XT talking Controls the security system primarily from within the house touch screen and Simon XT Talking Touchpad Key fob This keychain touchpad controls the security system from within or near the outside of your home Sensors Indoor motion Detects motion in protected indoor area When motion is detected the panel may res
25. isarm the system activate a panic alarm to call the central monitoring station in an emergency check system status and turn system controlled lights on or off all while providing voice feedback The touch screen also provides trouble beeps entry exit beeps and alarm sounds Panic Police or Fire Key fobs are handy for simple arming and disarming control functions They are portable and can be carried offsite in a purse or pocket Touchtone telephones can be used to communicate with your system while you are offsite Ask your installer if you have this feature Note The default master code is 1 2 3 4 when the security system is shipped from the factory You should change your code after your system is installed Simon XTi User Manual Using the Simon XTi security system You can operate the self contained security system through several different methods Use the main screen icons to arm disarm the system when you enter or exit your home check system status and to determine which sensors are active Use the emergency screen to communicate with the central monitoring station to report emergency panic police or fire alarms From the home screen press the Status Settings E icon to program certain user features See System configuration on page 21 Note Upon initial installation the battery may not be fully charged for as long as 36 hours A low battery icon will be present and trouble beeps will sound until the battery
26. lamation point indicates one or more windows are open N A indicates your system is not configured to support window sensors Depicts motion detected by the motion sensors in your home A green check indicates no recent motion detected A red exclamation point indicates motion was detected within the last 10 minutes A typical use for this feature would be to have a touch screen in the garage to see if movement is detected in the home before you enter the home N A indicates your system is not configured to support motion sensors Depicts other changes to protected property in your system For example activation of a water sensor freeze sensor or the movement of protected items A green check indicates no change since the last time you visited for movement of a protected item and all sensors are closed water or freeze sensors A red exclamation point indicates either a sensor is tripped or there is unacknowledged activity N A indicates your system is not configured to support property sensors Simon XTi User Manual Depending on the current arming state of your machine one of these icons will be displayed Press the ARM icon to access the Arming Screen Press a DISARM icon and provide a valid access code to disarm your system Note When disarming the system only intrusion burglary sensors are disarmed Environmental sensors such as smoke and carbon monoxide detectors stay active at all times Note Depending on your config
27. llows you to control which sensors are active at any given time Table 5 below describes the arming levels that you can set from the control panel Table 5 Arming levels Level Function Description 1 Disarm In this level only 24 hour sensors are active Environmental sensors such as smoke or carbon monoxide detectors stay active at all times 2 Arm door and window This level arms the door and window sensors while leaving the sensors away interior motion sensors disarmed 3 Arm motion sensors This level arms the interior motion sensors while leaving the exterior stay door and window sensors disarmed Note Depending on your configuration this option may not appear 4 Arm doors windows This level arms all sensors and motion sensors Arming disarming Arming a sensor makes it active and allows the panel to generate an alarm when a door or window is opened or when an unauthorized person enters a specific area Disarming makes the sensor inactive in the system The current arming level is shown on the screen see Table 4 on page 5 and changes in arming level are announced on the speaker Arming errors If you select an arming option on the Arm screen and there is an arming problem an arming error message screen will appear indicating what the problem is and how to correct It For example you might see a message that indicates that you need to close the front door Simon XTi User Manual 7 Correct the problem as
28. mon XTi User Manual 21 A blue icon depicts indicates an option is not selected To program an option first navigate to that option until it is displayed using the icons and then press the corresponding interactive icon e g checkbox radio icon data entry window etc If pressing the option value s interactive icon transitions to another screen make your changes there and press save or cancel when done Press E to enter the STATUS SETTINGS menu Table 13 Settings Menu structure Event History Direct Bypass Panel Status Chime Optional Ask your dealer for more information Note Has not been investigated by UL Special Chime Optional Ask your dealer for more information Note Has not been investigated by UL Lights Optional Ask your dealer for more information Note Has not been investigated by UL Door Locks Optional Ask your dealer for more information Note Has not been investigated by UL Voice Volume Beep Volume Brightness Default Screen Calibration Help Set Date Time System Tests Sensor Test Comm Test System Download Programming Access Codes Master Code User Codes 1 to 8 Duress Code Security Downloader Enable Phone Numbers Phone Number 4 22 Simon XTi User Manual Siren Options Panel Piezo Beeps Panel Voice Panel Piezo Alarms System Tests Sensor Test Comm Test System Download Interactive Services Note Optional Ask your dealer for more information Has not been investigated by UL
29. mpered with for example that the cover is taken off one of the sensors If the system is armed an alarm will occur Sensor icons change to red see Table 4 on page 5 oh icon appears and the red alarm pop up will appear if the system is armed Trouble beeps will start Correct the problem by resetting the sensor If this condition continues call your security system dealer The panel receiver may be experiencing some interference The system will call to notify the central monitoring station about this problem Some types of status conditions such as alarm history must be cleared manually To clear system status press CLEAR next to Panel Status in the STATUS amp SETTINGS menu If the trouble condition was a low system battery perform a sensor test The A should disappear if all trouble conditions have been corrected 20 Simon XTi User Manual System configuration Your Simon XTi security system allows you to program certain user options These options are accessed through the settings menu Settings menu To enter the settings menu press E located at the bottom right of the main screen Press to exit a menu or option edit mode and navigate up one level The panel automatically returns to the main screen after one minute of inactivity 4 minutes while performing a sensor test 5 seconds while entering an access code Code options The Simon XTi security system provides a system of codes to be entered when a certain l
30. n alarm 1 If you would like to hear additional alarm information press Listen 2 To cancel the alarm press the red alarm icon and enter a valid master or user code After alarms are canceled the system will be disarmed Fire alarm verification If this option is off the panel immediately reports to the central station when a smoke detector goes into alarm With this option on if a single smoke detector goes into alarm the panel will not report for 60 seconds unless another smoke detector goes into alarm If the first smoke detector is cleared of an alarm within the first 60 seconds no report will be sent to the central station unless it or a second smoke detector goes into alarm within the panel siren timeout period 5 minutes Ask your installer how this option is programmed Canceling and preventing accidental alarms One of the biggest concerns you might have regarding your security system is causing an accidental alarm Most accidental alarms occur when leaving the residence after arming the system or before disarming the system upon your return 12 Simon XTi User Manual There is a communicator delay dialer delay of 30 seconds programmed into the panel The panel will delay 30 seconds before dialing the central monitoring station remote phone to send reports You can have your installer program this delay time between 15 and 45 seconds To cancel an accidental alarm before the programmed dialer delay time expires pres
31. nment that may impact RF performance for example mirrors installed metal backed wall paper addition of other RF equipment e Ifa sensor doesn t meet minimum packet requirements contact your installer Comm test The comm test is used to check proper communication Note If Comm Test is not finished it will continue to run even if you exit program mode To perform a comm test 1 Enter the Status Settings menu 2 Scroll until System Tests is listed Press Enter 3 Enter your master code and press OK 4 Press Comm Test The panel displays if the comm test was successful or not Central station communication After performing sensor tests check that the system is reporting alarms successfully to the central station To test communication with the central station 1 Call the central station and tell the operator that you will be testing the system 2 Arm the system 32 Simon XTi User Manual 3 4 Test an emergency panic icon and trip at least one sensor of each type fire intrusion etc to verify that the appropriate alarms are working correctly There could be a 30 second delay on intrusion devices When you finish testing the system call the central station to verify that the alarms were received Note If your system is not connected to a central monitoring station you won t be able to perform the communication test System download You can initiate a download call to program your system with
32. ntering the home to avoid causing an alarm If your installer programmed your system for remote touchpad arming you must enter your home to start the entry delay before you can use your key fob to disarm the system Caution To avoid causing false alarms check with your installer on how your touchpad key fob options are programmed Panic alarms need to be silenced from the panel a remote touchpad or another key fob They cannot be silenced from the same key fob that activated the alarm For any key press on the Key fob hold the button until the indicator light blinks The key fob has the following buttons e Lock closed lock icon e Unlock open lock icon e Star star icon e Light light bulb icon Table 8 on page 16 describes how to use the key fob buttons Simon XTi User Manual 15 Table 8 Key fob button operation Task Instructions Arm doors and windows Arm doors windows and motion sensors Send a panic intrusion silent or emergency alarm to the central monitoring station Disarm your security system Press the Lock button once Press the Lock button twice Press the Lock and Unlock buttons simultaneously for 3 seconds Check with your installer to find out how the key fob panic buttons will operate Press the Unlock button once 16 Simon XTi User Manual How your system communicates Your system communicates by using status beeps alarm sirens panel screen messages an
33. o call your security system dealer if the problem continues This condition occurs if a system sensor has a low battery The sensor may still be communicating with the panel Trouble beeps will start Press and then press in the STATUS amp SETTINGS menu The panel will speak which sensors have low battery You may need to call your security system dealer to resolve this problem Some sensor batteries can be replaced by the homeowner This condition occurs if your security system could not communicate successfully to the central monitoring station Your system will try to report to the central monitoring station eight times before it tells you there is a fail to communicate problem Trouble beeps will start and the yellow triangle appears over the settings icon You may need to call your security system dealer if the problem continues This condition occurs if a door or window is open or a system sensor has been disturbed and not reset properly For example a door window sensor magnet may have been removed from the sensor Your system will indicate this condition to you by displaying a red SENSOR OPEN icon see Table 4 on page 5 and show the oh icon in the bottom right of the main screen Correct the problem by resetting the sensor If this condition continues call your security system dealer 19 Condition Description Sensor tampered RF jam detected Clearing status This condition occurs when a sensor is physically ta
34. on Exit entry delay Your Simon XTi provides a delay after entering or exiting your home before the system is armed or disarmed Table 6 below provides details for the entry and exit delay features Table 6 Entry and exit delay details Function Description Entry delay Some active sensors cause immediate alarms when tripped Other sensors if enrolled in a delayed response group start an entry delay that lets you enter the premises and disarm the system When you enter your home you will hear beeps during the entry delay see Status beeps on page 17 If the system has not been disarmed by the end of the entry delay an alarm occurs The entry delay time is programmed by the installer No delay If the system was armed with the no delay feature activated there will be no entry delay and the alarm will occur immediately Exit delay The exit delay is the amount of time the system gives you to exit the home before the system is armed During the delay you can vacate the premises through a delayed response door without causing an alarm Beeps will sound during the exit delay see Status beeps on page 17 The exit delay time is programmed by the installer Protest during arming The system may protest an arming level change if certain abnormal conditions exist If a sensor that is active in the requested arming level is open the system sounds protest beeps and automatically bypasses the open sensor depending on the s
35. one Emphasize that no one should enter the premises if they hear sirens in the house If you arrive at the premises and hear sirens do no enter Call for emergency assistance with your cell phone or from a neighbor s phone Simon XTi User Manual 35 Smoke Detector Placement NOTE NOTE NOTE Your floor plan A smoke detector should Bedroom Bedroom be located on each level Living Dining 9 Bedroom Bedroom Room Room Living O T Room Recreation Basement Basement Room Dining Kitchen Bedroom Bedroom Smoke detectors should Room a be located between the E Hall sleeping area and the rest Living e of the family living unit Room Bedroom Dining i Bedroom Room Kitchen In family living units with more TV amp than one sleeping area locate a Room Oo smoke detector at each area Living Room Bedroom Oo Bedroom Ceiling mounted smoke detectors should be located in the center of the room or hall or not less than 4 inches from the wall When the detector is mounted on the wall the top of the detector should be 4 to 12 inches from the ceiling Do not install smoke detectors where normal ambient temperatures are above 100 F or below 40 F Also do not locate detectors in front of AC Heat registers or other locations where normal air circulation will keep smoke from entering the detector Additional inform
36. option may not appear To arm doors windows and motion sensors level 4 Nn J 1 Press Pa 2 Press ARM ALL AWAY see Figure 3 on page 8 3 Ifa code is required enter your code when the keypad screen appears The panel speaks Doors and Windows On Motions On starts an exit delay and sounds exit beeps in groups of four until the exit delay expires Unvacated premises Unvacated premises is a feature that determines whether the system automatically arms down to level 2 doors and windows if you arm the system to level 4 doors windows and motion sensors without opening or closing a perimeter door on or remains at the armed level chosen off This feature does not work from a key fob Autobypass must be on for this feature to work Ask your installer how this option is programmed Swinger shutdown This setting determines if a sensor or zone will go into alarm only once during an arming period an active arming level and will not be active again until the alarm is canceled Swinger Shutdown is enabled or the sensor or zone will always be active and will go into alarm multiple times during an arming period an active arming level without canceling the alarm Swinger Shutdown is disabled Simon XTi User Manual Note Swinger shutdown does not affect Smoke Fire Carbon Monoxide and Environmental sensors Ask your installer how this option is programmed and have them explain how it will affect your system operati
37. pond by sounding chimes or an alarm Outdoor motion Detects motion in a protected outdoor area When motion is detected the system may respond by sounding chimes or turning on outside lights These sensors are not used for intrusion detection Glassbreak sensor Glassbreak sensors respond to shock waves of breaking glass Door window Detects the opening of a door or window Smoke Detects smoke or a significant rise in temperature They have a built in siren that sounds when smoke or a significant rise in temperature is detected Carbon monoxide Detects carbon monoxide They have a built in siren that sounds when carbon monoxide is detected a Not verified for use by UL You can send commands or instruct your security system through a series of key presses on the panel touchpads or a remote telephone Simon XTi User Manual 1 Table 2 System communication devices Device Description Control panel Simon XT talking touch screen Key fob Telephone You can enter commands for your security system using the graphical user interface on the panel Depending on how your system is programmed you may need to enter an access code for certain commands An access code is a numeric code that allows authorization to operate your security system The two way talking touch screen is a wireless device that provides a graphical user interface that allows you to arm the system doors windows and motion sensors d
38. r access codes Table 16 Access codes Code description Code Master code User code 1 User code 2 User code 3 User code 4 User code 5 User code 6 User code 7 User code 8 Duress code Delays Use Table 17 on page 39 to record your delay times 38 Simon XTi User Manual Table 17 Delays Delay Time Exit delay Entry delay Simon XTi system quick reference Task Instructions Level 1 Disarm the system Level 2 Arm doors and windows Level 3 Arm motion sensors Level 4 Arm doors windows and motions Activate no delay Activate panic alarm Check system status Toggle chime or special chime mode Bypass a sensor Control panel Press PRESS TO DISARM and enter your access code Key fob Press Unlock Telephone Press 1 Control panel Press PRESS TO ARM then press Doors Windows Only and enter your access code if required Key fob Press Lock Telephone Press 2 Control panel Press PRESS TO ARM then press Motion Sensors Only and enter your access code if required Telephone Press 3 Control panel Press PRESS TO ARM then press Arm All and enter your code if required Key fob Press Lock twice Telephone Press 2 3 Control panel Press PRESS TO ARM set Entry Delay to OFF then press Doors Windows Only Key fob Press Lock Telephone Press 2 3 Control panel Enter the Emergency Screen and press Panic Police or Fire K
39. s the red alarm pop up and enter your access code The panel will speak Alarm Cancel and sound beeps Note There is no dialer delay for fire alarms Guidelines for preventing accidental alarms Use the following guidelines to prevent accidental alarms e Close doors and windows before you leave your house e Gather your belongings so you can exit immediately after arming the system e Always enter and exit within the programmed delay times e Make sure you leave through a door that has a delay time set for it e Disarm your system immediately upon returning home e Be aware of the devices in your system and learn how each one operates e If you have pets ask your installer if you need pet lenses in your motion detectors e Check the location of your smoke detectors Smoke detectors near bathrooms and kitchens can be tripped by steam and smoke formed by cooking e Make a note of the display system beeps and indicator lights that indicate the current system status Chimes Use the chime feature to signal when a protected door is opened while the system is disarmed The panel chimes twice when a chime sensor is tripped if the chime mode is enabled This feature allows you to be notified when family members are going in and out of your home The chime and special chime features are turned on or off in the System menu See Chime on page 23 and Special chime on page 24 Note If there are no chime sensors in your system t
40. signated door may be opened and closed only once If you close the designated door behind you when you exit you will need to disarm the system upon re entering Leave the designated door open while using the quick exit feature Exit delay extension If enabled by your installer the exit delay extension feature will recognize when you arm the system leave your house and then quickly re enter for example if you forget your car keys If this happens the system will restart your exit delay to give you the full exit delay again Bypassing sensors Bypassing a sensor allows you to open the sensor while the system is armed For example if your doors and windows are armed and you want to open your kitchen window but do not want to disarm the entire system you can bypass the kitchen window sensor and then open the kitchen window without causing an alarm Bypassed sensors are automatically unbypassed when the arming level is changed to a level where the sensor is not active Simon XTi User Manual 11 To bypass or unbypass a sensor 1 Press 2 Press SELECT Nilda 3 Enter your master code 4 NOT Next to the sensor name select to bypass the selected sensor or to not bypass the selected sensor Alarms The system provides a series of alarms that indicate an unusual occurrence When an alarm is active the red alarm pop up display shows with a message explaining what caused the alarm ALARM LISTEN To listen to and cancel a
41. unds alarm beeps To program panel piezo alarm 1 From the Programming screen press SIREN OPTIONS 2 Toturnon panel piezo alarms press U To turn off press M Note J indicates the panel piezo alarms is turned on 3 Press CLOSE repeatedly to exit menus Simon XTi User Manual 29 Caution Turning this option off will disable all system sirens This option should only be turned off if the panel is configured with external sirens Ask your installer for more information Version This menu is a read only display of the system s firmware version the touch screen version and copyright information 30 Simon XTi User Manual Testing This section includes e Sensor test e Comm test e System download Sensor test You should test sensors one at a time to make sure they are sending strong signals to the panel You should test the sensors at least once a week To perform the sensor test Enter the Status amp Settings menu Scroll until System Tests is listed Press Enter Enter your master code and press OK All sensors learned into your system will be listed 1 2 3 4 Press Sensor Test 5 6 Test any sensor you want by tripping the sensor see Table 14 below for details on how to trip each device 7 The display will update with the total number of packets received from each individual sensor see Table 14 below for minimum number of packets required Table 14 Tripping sensors for sensor test
42. uration the Motions Only icon may not appear Press to access the settings screen Simon XTi features The Simon XTi features provide you with the ability to perform the following functions e Arm perimeter doors and windows and interior motion sensors to indicate intruders e Use the emergency screen to send quick response alerts to the central monitoring station e Access the system from a key fob similar to the one used for your car e Access the system from a remote telephone e Disable sensors so you can leave a window open while the system is armed e Getan audio alert when a protected door is opened while the system is disarmed e Get an audio alert if movement of a protected asset is detected group 43 Cross zoning Cross zoning two trip refers to two different motion sensors that must be tripped within two minutes of each other to report an alarm to the central station Figure 2 on page 7 shows the path of a person walking from the kitchen to the living room When the person is detected walking through the kitchen the motion sensor in the kitchen is tripped sounding a local alarm If motion is detected by the living room motion sensor within two minutes an alarm report will be sent to the central station Note Contact your installer for more information 6 Simon XTi User Manual Figure 2 Cross zone diagram Motion sensor Motion sensor Path of person walking Home security The Simon XTi a
43. ystem configuration Silent exit The silent exit feature silences the status beeps that accompany the exit delay Press ON next to Silent exit Figure 3 on page 8 before pressing the arming level icon to silence status beeps The panel will still beep at the beginning and end of the exit delay Note Enabling silent exit doubles the exit delay time No entry delay Use the no entry delay feature when you are staying at home or when you are away from home and will carry a wireless keyfob to disarm the system before opening a protected door Check with your installer to find out how this option is programmed 10 Simon XTi User Manual 1 Close all door and windows Nn 2 Press wl 3 Press the OFF next to Entry Delay see Figure 3 on page 8 4 Press your desired arming level The arming countdown begins The screen displays Y clock with a red strike through with your arming level and speaks Doors and Windows On No Entry Delay Note To avoid causing an alarm you must disarm the system with a wireless keyfob before entering your home Quick exit Use the quick exit feature when you want to briefly leave the house while the system is stilled armed for instance to get the newspaper This feature must be enabled by your installer To enable Quick Exit 1 Press PRESS TO DISARM 2 Press on the touch screen This allows a designated exit door to be open for up to 2 minutes without triggering an alarm Note The de
Download Pdf Manuals
Related Search