User Guide
Contents
1. hange a new belt F by going through all connect wires that from the arm to base and ough the bridge for correct position et up the gear axis to the bridge and screwed it Note do not press the belt Put the belt around the axis gear and motor gear Plug all the connect wires C that form the arm to PC board and ignitor Adjust the pan home position Screw the base housing cover B N4 A 7 Fixture Cleaning The cleaning of interna and external optical lenses and or mirrors must be carried out d periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics y Clean with soft cloth using normal glass cleaning fluid i Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 1 1993 EN61000 3 2 1995 EN61000 3 3 1995 EN55014 2 1997 CATEGORY II EN61000 4 2 1995 EN61000 4 3 1995 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1995 EN61000 4 11 1994 Harmonized Standard EN60598 12. that the units can receive DMX signal Press the MENU button up to when the Addr is showing on the display Pressing ENTER button and the display wil blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units 5 4 DMX512 Configuration DMX512 CONFIGURATION CHANNEL 2 SHUTTER Gobo Shaking Goze 14 Gess 13 Gere 12 Gere l1 Geese 10 Gore 9 Goss 8 Gssc 7 Gcoa5 Goss Gerr4 Gets 3 3 Light blue Gers 2 Orange Gere 22 Ge Green B ecxout White cn 5 5 DMX512 Connection The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels DMX512 COMMON 120 ohm 1 4W INPUT wll OUTPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 If you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 D
3. 1993 Safety of household and similar electrical appliances Part 1 General requirements Following the provisions of the Low Voltage Directive 73 23 EEC and 93 68 EEC EC Declaration of Conformity We declare that our products remote controller comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55015 1993 EN50082 1 1997 EN61000 3 2 1995 EN61000 3 3 1995
4. 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on 2 light show bes In a means the unit works somay and CLO means 2 light show In order to create a great light show you can set CL Sh on the second unit to get contrast movement to each other even if you have two units only Li slave mode 20 5 2 Easy Controller l The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote control on the first unit will control all the other units for Stand by Strobe Next and Fast Slow function 1 STAND BY To blackout all the unit 2 STROBE NEXT Under FAST mode the light will strobe in three different ways a Strobe in different gobos and colors b Synchronous strobe in white color c Two light strobe in white color If the unit in slow mode press NEXT button to choose desired color and gobo It will change ten colors and then change one gobo 3 FAST SLOW When the LED is off it is in FAST mode The unit s movement Pan Tilt amp Gobo Color is sound activated If the LED on it is in SLOW mode Pan Tilt is sound activated but Gobo Color wheel are static controlled by Next button 7 5 3 Universal DMX Controller if you use a universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so
5. Intelligent Moving Head Professional Lighting Technology User Guide Guilt for the best performance TABLE OF CONTENTS Safety Instruction Technical Specification Lamp How To Set The Unit 4 1 Control Panel 4 2 Main Function How To Control The Unit 5 1 Master Slave Built In Preprogrammed Function 5 2 Easy Controller 5 3 Universal DMX Controller 5 4 DMX512 Configuration 5 5 DMX512 Connection Troubleshooting Fixture Cleaning 1 Safety Instruction PL g Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rair Please read carefully the instruction which includes important or moisture information about the installation usage and maintenance WARNING Never touch bulb with bare fingers as it is very hot after using Please keep this User Guide for future consultation If you sell the unit to another user be Do not start on the unit without bulb enclosure or housing are damaged e e Hotlamp explosion hazard Do not open the unit within five minutes after switching off e sure that they also receive this instruction booklet bd The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Do not look directly at the light while the bulb is on Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the volt
6. MX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not be branched or split to a Y cable DMX512 is a ve high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 6 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connect power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on a
7. age and frequency of power supply match the power requirements of the unit The unit is designed for use with the ELC 24V 25OW Do not use any other type of lamp Caution _ It s important to ground the yellow green conductor to earth in order to avoid electric shock There are no user serviceable parts inside the unit Do not open the housing or The unit is for indoor use only Use only in a dry location attempt any repairs yourself In the unlikely event your unit may require service The unit must be installed in a location with adequate ventilation at least 50cm from please contact your nearest dealer adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before fuse lamp replacement or servicing Installation Replace fuse lamp only with the same type The unit should be mounted via its screw holes on the bottom of the base Use clamps to fix th Make sure there is no flammable materials close to the unit while operating as it is fire unit to truss Always ensure that the unit is firmly fixed to avoid vibration and slipping while hazard operating Always ensure that the structure to which you are attaching the unit is secure and is Use safety chain when fixes this unit Don t handle the unit by taking its head only but able to support a weight of 15kgs for each unit always by taking its base Maximum ambient temperature is TA 40 C Don t operate it at where the temperature is higher than th
8. ance do not open the fixture within 15 minutes until the unit cools down after switching off e Lamp ELC 24V 250W 1 Always switch off the main supply and never handle the lamp or luminaries when is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation 3 Never operate the lamp without appropriate shielding 4 Make sure the lamp is located in the center for the best spot Diagram for Lamp changin 4 How To Set The Unit 4 1 Contro Panel O O MIN MAX MIC ONLY FOR REMOTE O vmx SENSITIVITY MASTER CONTROL CA 8 O SLAVE OOOO MENU DOWN UP ENTER DMXIN DMXOUT 1 Display To show the various menu and the selected functions 2 LED DMX input present master mode 3 Button 4 Remote controller input By connect to the 1 4 microphone jack to control the unit for Stand by Strobe Next and Fast Slow function 5 Sensitivity To adjust the microphone receiving sensitivity 6 Microphone To receives audio signal for sound activation 7 DMX input output For DMX512 link use 3 pin XLR plug cable to link the unit together 4 2 Main Function To select any of the given functions press the MENU button up to when the required one i showing on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mo
9. de has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENL button The main functions are showing below AddrH 5 DMX512 Address Setting arg ET rth Show Mode Show 1 aoe Sh A Show Mode Show 2 cmd oo Slave Mode Normal oe L Shi Slave mode 2 Light Show 2 masa ne Pan Normal parn a Pan Inversion MENU ror ne Tilt Normal yd CLE TS 7 e Tilt Inversion FIE oT dor Display Normal A dbr 4 Display Inversion m Agdu Focus Adjust meesi Self Test FheS Fixture Hours r SP iE Reset Ca MAOT DMX512 Address Setting Press the MENU button up to when the Addr is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to tt functions without any change press the MENU button again Show Mode Press the MENU button up To when the Ghid is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP b tton to select the Sh i show 1 or Sh d Z show 2 mode Once the mode has been selected press the ENTER button to se
10. e Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Display Inversion 3 It is a for you to install the unit on the floor or under ceiling Press the MENU button up porie when the is blinking on the display Use the ENTER button to change to the mode oP i display inversion It will automatically store after 8 seconds Or press the ENTER button again return to the mode I JSP display normal To go back to the functions press th MENU button oSA Display norma mode for the fixture putting on the floor JSP Display inversion mode for the fixture fixing under ceiling me EAU Focus Adjust Fa Press the MENU button up to when the eA is blinking on the display Pressing ENTER button the unit will focus on tilt 90 and then the unit will focus on pan 0 pan 90 pan180 pan270 in every pressing ENTER button To go back to the functions press the MENU button again pm i iT L 2 Self Test Press the MENU button up to when the teSE is blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions presg the MENU button again rer 4 Fixture Hours Press the MENU button up to when the rae is blinking on the display Pressing ENTER button and the display will show the number
11. is Unit surface temperature may reach up to 85C Don t touch the housing bare hand during its operation and allow about 15 minutes to cool down before replacing bulb or serving as the unit could be very hot In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts l Don t connect the device to any dimmer pack Do not touch any wire during operation as high voltage might be causing electric shock 2 Technical Specification Power supply AC 120V 60Hz AC 230 240 250V 50 60Hz e Lamp _ ELC 24V 250W e Optical system Standard 11 focused beam angle Focus can be adjusted by manual e Gobo wheel Independent gobo wheel with 14 gobos plus open and shutter Blackout and strobe speed variable 1 7 flashes per second e Color wheel Independent color wheel with 11 dichroic mirrors plus white e Movement Pan 540 in 2 8 second Tilt 270 in 1 6 second e DMX Channels Standard DMX512 signal addressing and can be controlled by any universal DMX controller Channel 1 Shutter Channel 2 Gobos Channel 3 Colors Channel 4 Pan motion Channel 5 Tilt motion Dimension 290mm x 330mm x 380mm L x W x H e Weight 11 kgs In case of replacement of the lamp or mainten
12. nd no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the unit Set the proper address D No response to the sound 1 Check the unit that is not receiving DMX signal 2 Check the unit that is not set to display mode 3 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition F The lamp is cutting out intermittently 1 The lamp is not working well Check the main voltage either too high or too low 2 Internal temperature may be too high Check and if necessary replace the fan on the head aw 6 If The pan belt is broken 1 Turn off the main power 2 Unscrew all the screws A and open the base housing cover B 3 Unplug all the connect wires C that from the arm to PC board and ignitor Unscrew the screws D that fix the axis gear E
13. of working hours of the unit To go back t the functions press the MENU button again mo Reset J Press the MENU button up to when the ic Pe is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show AE 5 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slaver Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to set the first unit in master mode Ghid and select Ghi show 1 or Gh g rm show 2 mode Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music eae other units vip f i I have to set in slave mode 241d and select 20 normal or cL CLSA
14. tup or E eS return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again aana 2m Show 1 mode Fixture is placed on the floor Tilt movement angle 210 She Show 2 mode Fixture is fixed under ceiling Tilt movement angle 90 Slave Mode riser atl Press the MENU button up to when the Ltd is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 0 normal or clon 2 light show mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again roa Jt UI pan inversion Press the MENU button up to when the i Pdo ENTER button and the display will blink Use DOWN and UP button to select the is showing on the display Pressing man normal or pan inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again en Tilt Inversion Press the MENU button up to when the Leu is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the OO normal or a pan inversion mod
Download Pdf Manuals
Related Search