Operating instructions Memory plug E30398
Contents
1. Write protected Read Write Sensor of the same type Identical sensor IODD e f the memory plug is empty no parameter set saved a parameter set can be saved e Ifthe memory plug is full a parameter set is saved it is protected against further writing A parameter set can be written to the memory plug It is not protected against overwriting Sensors of the same type have the same IO Link device ID The series number may be different The IO Link device ID is an unambiguous device identifi cation assigned by the manufacturer Physically identical device The series number of the sen sor and the saved parameter set are the same abbreviation for IO Device Description It is a file describing the parameters of the O link devices This file can be interpreted by machines An IODD is assigned to each IO Link device ID 2 Safety instructions Please read this document prior to set up of the unit Ensure that the product is Suitable for your application without any restrictions If the operating instructions or the technical data are not adhered to personal injury and or damage to property can occur If you change parameters during operation this will influence the function Ensure that no malfunction or dangerous conditions will occur in the plant 3 Factory setting On delivery the memory plug is empty no parameter set saved When the supply voltage is applied the LED WRITE flashes slowly 12. gt The memory plug writes its parameter set o to the sensor Writing process READ WRITE Mo Process terminated This process only works for sensors of the same type sensors with the same IO Link device ID 6 4 Set the parameters of the replacement sensor Requirement memory plug full in the mode Write protected or Read Write Write protected Read Write gt Connect the memory plug to the supply G f Q a voltage READ WRITE READ WRITE Ko o gt Connect the memory plug with a sensor of the same type u If the memory plug is used in the Read Write mode the sensor must have the factory setting If in doubt reset the sensor gt The memory plug writes its parameter set to the new sensor c amp G READ WRITE READ WRITE fom ow Writing process Writing process G hf READ WRITE READ WRITE Lo feo Process termi Process termi nated nated 10 6 5 Restore the parameter set of a sensor Requirement memory plug full in the mode Write protected gt Connect the memory plug between the G 0 sensor and the evaluation unit of the READ WRITE installation lO gt Switch the supply voltage of the installation G A off and on again READ_WRITE gt The memory plug writes the original o parameter set P to the sensor Writing process G READ WRITE Mo Process terminated 6 6 Write to the memory plug via PC EW You need the IO
3. 4 to the higher level system is stopped Error in data processing E wam y Sensor cable removed during transmission Connect the sensor cable to the memory plug again Unknown sensor connected e g gt Connect an IO Link 1 0 sensor from ifm e 1O Link 1 0 sensor of another manufac electronic turer gt Connect an O Link 1 1 sensor e Sensor not equipped with IO Link Parameter set of the connected sensor gt gt Connect sensors requiring a storage 2048 bytes capacity of less than 2048 bytes data sheet of the sensor The sensor does not support any saving gt Connect sensors supporting IO Link of data and i of data data sheet of the sensor Sensor locked writing impossible gt Connect an unlocked sensor or unlock sensor The parameter set of the connected sensor does not correspond to the parameter set in the memory plug Cause of the fault The connected sensor is not of the same gt Connect a sensor of the same type type sensor with the same O Link device ID More information at www ifm com 25
4. Link interface order no E30396 to connect the memory plug to a PC gt Start the FDT service program ifm Container in the point to point mode gt Select offline mode gt The list of the available IO Link devices is displayed ifm Container Tool Mode Assistant Device Selection Please select one device from the list D Device Type Version Vendor PROOZE 1 01 0703 sleat OA P 1 01 0703 iim electronic PPO520 1 01 0703 iim electronic CA ea hne fime o Pos iim electronic E PP7550 1 01 0703 fiset Update Please update the Device Catalogue if you can t find aDTM you expect to be there Help Back Ment gt Cancel gt Mark the IO Link sensor the parameter set of which is to be written in the memory plug in the list gt Continue with Next 12 Unnamed ifm Container lt IO Link Channel gt PP7554 Configuration File Edt Yiew Device Tools Window Help Oe Robie aBore of lt 10 Link Channel gt PP7554 C IO Link pp7554 Pressure sensor PP7554 Switching output E ParameterGroups s Switching output SP Switch on point 2 50 bar 0 90 Output configuration Memory Min Delay time Ne Danen IP Switch off point 2 30 bar 0 95 Display settings Teach Miscellaneous Service Parameter Output 1 SPx Switch on point x The switch point SPx indicates the upper limit value at which the output changes
5. by an access code cannot be overwritten by the memory plug EW The memory plug saves writes data after the following operations e After application of the supply voltage e After interrupting and restoring the connection between the memory plug and the sensor After saving the parameters all sensor signals are linked through without being changed The output function of the sensor its quality and speed remain unchanged An integrated memory plug does not influence the complete system Recommended operating mode Operation in the Write protected mode is recommended This mode en sures that a parameter set is not unintentionally overwritten In the Read Write mode the memory plug is not write protected 1 The manufacturer of an IO Link sensor is responsible for providing all parameters necessary for an exchange The memory plug reads this infor mation from the sensor and saves exactly these parameters The memory plug cannot be used in a system with IO Link master The functionality of the system cannot be guaranteed 5 Electrical connection The memory plug is an accessory intended for connection to IO Link devices 1 Sensor 2 Memory plug 6 6 Operation 6 1 Save the parameter set of a sensor once Requirement The memory plug is used as delivered empty Write protected gt Connect the memory plug to the supply voltage READ WRITE gt Connect memory plug and sensor gt The memory plug reads the param
6. CE 11 2011 704930 02 ifm electronic Operating instructions Memory plug E30398 Contents MD RW a UO ANON E EA E E E pene 3 ML INNO S Uo ER 3 Me MUNIN WSO Gates sce nate E A E esses cass ee nee Seneeae 3 ZS Ae MVS UNG ONS csecsen aeon e ES EET eevee tae eects oie 4 SACU Se CUI E A E A 4 Functions and features oles tsccienctsnace ates cms peteseantstiaicsheataeavaeeatiseesonsasctaeebe eicaseseniaes 5 4 1 Applications without PC cc ccssssssssssssesssessesessesseseesesseseeesseseeseesnsaees 5 4 2 Applications with PC c ccccccsecscssscsssecsesscsssecsssecessecsssesecsesassseessssessseseees 5 4 3 Basic operating CONCILIONS c ccsssessseessccsssesssestssssessessssessreestsseserseseses 5 SIO GH Ia COMMS CMOMN escis o e E e S 6 0 OS I essin reee aA RRR ERARE EEEE EAER 7 6 1 Save the parameter set Of a Sensor ONCE cccsesssssseessesssecsesesesseeassesseeaees 7 6 2 Save the parameter set of a sensor continuously ce esesecesesesseeeseseeeeeees 8 6 3 Copy the parameter Set Of a Sensor cccecssecsesseessssseseessesecsseessesesseeeees 9 6 4 Set the parameters of the replacement sensor cccsecsesseeseseseteeeeeeees 10 6 5 Restore the parameter Set Of a Sensor ccccsssssscssssssssseesssecsecsssessesatens 11 6 6 Write to the memory plug Vid PC ee cceecseesssesssetecsssecsesesseeesssseseeeeses 12 6 7 Read from the memory plug via PC ccseessssesssssssssss
7. Hz In this state one parameter set can be written to the memory plug once Then it changes to the mode Write protected 4 Functions and features The memory plug saves parameter sets of IO Link devices It offers the following UK options e Bi directional backup for IO Link V1 1 sensors e Bi directional backup for IO Link V1 0 sensors from ifm electronic e Preconfiguration as data carrier via PC 4 1 Applications without PC Save the parameter set of a sensor once 6 1 Save the parameter set of a sensor continuously 6 2 e Copy the parameter set of a sensor copy to several sensors of the same type e g in series production or for fast set up 6 3 e Set the parameters of replacement sensors without using further tools without configuration tools or menu handling 6 4 e Restore the parameter set of a sensor e g during start up of an installation gt 9 5 4 2 Applications with PC e Write to the memory plug via PC save the parameter set in the memory plug 6 6 e Read the memory plug via PC 6 7 e Use the memory plug as data carrier 6 8 e Configure the memory plug via PC gt 7 1 4 3 Basic operating conditions e Negative switching sensors are not supported e The memory plug cannot be used with IO Link actuators e The memory plug is intended for saving the data of IO Link sensors used without IO Link master e Data in the parameter set of the sensor protected
8. aster The memory plug acts as master if it is connected with a sensor Type of transmission COM1 4 8 kBaud COM2 38 4 kBaud COM3 230 kBaud is not supported IO Link revision 1 1 SDCI standard IEC 61131 9 Draft Number of ports electrically connected Smallest detectable current 3 for sensor detection mA IO Link device The memory plug acts as device if it is used with the ifm Container FDT service program Type of transmission O Link revision Profi 23 Power on delay time according to the baud rate data organisation storage volume and communication behaviour of the connected sensor typical values s Storage volume Example For a sensor with approx 20 parameters a storage volume of 0 1 K and a baud rate of 38 4 kBaud the memory plug needs a power on delay time of max 0 5 s delay time of the connected sensor If the parameters of sensor and memory plug are identi cal this time is reduced considerably Protection class Mo LT gt 100 500 V DC Housing materials PA PACM 12 TROGAMID PET sealing FPM Viton coupling nut high grade stainless steel 316L 1 4404 connector TPU M12 connector 24 10 Troubleshooting For all errors the following applies e The parameter set in the memory plug remains It is not damaged by faulty reading or writing The error remains until it has been removed e If the memory plug detects an error the transmission of the sensor output OUT1 pin
9. eter set READ WRITE of the sensor and saves it feo Reading process READ WRITE Mo Process terminated Memory plug full Write protected The empty memory plug can carry out this process only once It can however be reset to the factory setting 7 Configure the memory plug Do not install a brand new memory plug before setting the sensor param eters If it is integrated before the parameter setting has been completed it saves a non optimised parameter set and any further change in the parameter set of the connected sensor is undone 6 2 Save the parameter set of a sensor continuously Requirement memory plug in the Read Write mode To change from Write protected to Read Write 7 Configure memory plug gt Connect the memory plug between the sensor and the evaluation unit of the READ_ WRITE installation i oll Display when the memory plug is READ WRITE fe oll Display when the memory plug is full The parameter set of the sensor is changed P gt P1 sor and connect it again READ WRITE gt The memory plug reads the changed feo parameter set P1 and saves it Reading process G READ WRITE fe o Process terminated 6 3 Copy the parameter set of a sensor Requirement memory plug full in the mode Write protected gt Connect the memory plug to the supply Q A voltage READ WRITE gt Connect the memory plug with a sensor of the same type READ WRITE
10. its switching status When the switch point has been reached due to the increasing process value the corresponding output switches SPx can occur as an individual menu item as well as in conjunction with the reset point rPx and the hysteresis HYSx In the latter case the reset point also changes automatically when the switch point is changed i e the difference between SP and rP depends on the hysteresis set First set the display unit Uni before changing the switch point This avoids rounding errors generated during internal conversion to other units eet Apply gt Set the parameters as requested gt Connect the memory plug via the IO Link interface gt Click on the symbol Download Window Help BRO ae Parameter Download to device Device agls PP75SE gt The parameter set is saved in the memory plug If the Memory Plug is connected to a sensor after this operation it writes the saved parameter set in the sensor Then the parameter set of the sensor is saved again in the Memory Plug for verification 13 6 7 Read from the memory plug via PC gt Connect the memory plug via the IO Link interface gt Start the FDT service program ifm Container in the point to point mode ifm Container Tool Mode Assistant Action Selection Please select the action to execute D Automatic device selection fonline i Automatically detects all devices connected to this computer You can
11. select one of them to work with C Manual device selection foffline E Manually select a device type from the Device Catalogue The device doesn t c have to be connected with this computer pen file 7 Open an existing project file gt Activate the option field Automatic device selection online and continue with Next 14 gt The memory plug transmits its saved parameter set ifm Container Tool Mode Assistant Upload Device Parameters Tells the device DTM to upload the current parameters from the connected D device Fa Tells the device DTM to upload the current parameters from the connected device Uploading Cancel 4 gt The parameter set in the memory plug is displayed together with the photo of the sensor concerned here TR2432 Unnamed ifm Container lt IO Link Channel gt TR2432 Configuration iol xj File Edit View Device Tools Window Help Dea obPeebornw op lt IO Link Channel gt TR2432 C lt I0 Link Channel gt TR2432 Acce IO Link TR2432 Temperature sensor Memory Plug Switching output E ParameterGroups Min Max Step Switching output SP Switch on point e0 0 1c a98 300 0 01 Output configuration eri imis Min Max Step Calibration 2 teed Bat cy 50 0 m Cc 40 0 59 8 0 1 Delay time 15 This allows the following possibilities Check the current parameter setting Change the curren
12. ssssesssssseseesererseses 14 6 8 Use the memory plug as data carrier ccscceessessessssteessestseeesssesserseeees 16 6 9 Operating WIG ANOS sssrin anera ARNE aN E ai uanesntars 17 Contigure the memory plug cerscscssccssnandccneincadiad a 18 Pl Coniguration Va PO ossia E E 18 1 2 Configuration Via teach DUHOM serisini carnai 20 8 Scale drawing as ssccndccesncnsnasnidn canisensivandeuncaanidhannsedeaabuavesanscnsnnuneelrandisennsdanneeanes 22 SE E Ee E e E E E E E A ANE 23 10 AOU NOOU ec N E nuance eenescenits 25 1 Preliminary note 1 1 Symbols used Instructions Reaction result Cross reference Important note Non compliance can result in malfunction or interference Information Supplementary note LED on LED off LED flashes slowly 1 Hz LED flashes quickly 4 Hz LED flickers tke oe BQ 1 2 Terms used Memory plug Plug with storage medium Memory plug empty Setting at the factory No parameter set is saved in the memory plug The memory plug has to be connected to a sensor or a PC system in order to save a valid parameter set Memory plug full A valid parameter set is available in the memory of the memory plug Memory plug trans The memory plug is transparent if after successful saving parent of the parameters all unfiltered sensor signals are trans mitted to the higher level system For further data operation the operating voltage or the connection sensor memory plug must be interrupted once
13. t parameter setting Save the changed parameter set in the Memory Plug gt Click on the symbol Download Window Help ebenan Farameter Download to device Device cols BPPYSE If the Memory Plug is connected to a sensor after this operation it writes the saved parameter set in the sensor Then the parameter set of the sensor is saved again in the Memory Plug for verification Save the changed parameter set in the FDT service program ifm Container gt Click on the symbol Save da Unnamed ifm Container lt Device Tools Wi BEJE 6 8 Use the memory plug as data carrier Memory plugs can be used as external storage medium gt 16 When the installation has been set up keep units with saved parameter sets in a safe place 6 9 Operating indicators G No supply voltage READ WRITE Memory plug with factory setting no parameter set saved After one writing process change to the Write protected mode Memory plug with saved parameter set in the Write protected mode Memory plug without saved parameter set in the Read Write mode Memory plug with saved parameter set in the Read Write mode Memory plug reads the parameter set of the sensor Memory plug writes the saved parameter set in the sensor Memory plug in the Read Write mode error in data processing Memory plug in the Write protected mode error in data processing The connected sensor is not of
14. the same type This state remains until a sensor of the same type is connected or the voltage supply is interrupted 7 Configure the memory plug 7 1 Configuration via PC gt Start the FDT service program ifm Container in the point to point mode gt Select offline mode gt The list of the available IO Link devices is displayed gt Mark the memory plug in the list ifm Container Tool Mode Assistant i Device Selection Please select one device from the list D Device Type Version Vendor Che ps homem menm Ce ps hoen imee Ce prs homem imee O Ce pa homem imenom Ce prs homem menm Ce prs homem fime Update Please update the Device Catalogue if you can t find a DTM you expect to be there Help Back Next gt Cancel de gt Continue with Next 18 gt Connect the memory plug via the IO Link interface gt Click on the symbol Connect File Edit View Device Tools Window Help Dae oBielbe Bo 2 amp Ng e On line OFF line Toggle gt The current setting of the memory plug is indicated in the status display 1 Unnamed ifm Container lt IO Link Channel gt E30398 Configuration o x UK File Edit View Device Tools Window Help Dae aos eobiorat B lt I0 Link Channel gt 30398 C IO Link Memory Plug E30398 Memory Plug 30398 ParameterGroups MP S Memory Plug state Emp
15. ty Write protected 10 Link Standard Memory Plug READ WRITE MP_CMD RESET command 2 MP_CMD WRITE PROTECT command MP_CMD READ WRITE command 4 1 status display 2 button Reset 3 button Write Protect 4 button Read Write gt Press the requested button to change the setting Reset 2 restores the factory setting of the memory plug The memory plug is set to the mode Write protected by Write Protect 3 The memory plug is set to the mode Read Write by Read Write 4 gt The command is immediately sent to the connected memory plug the status display 1 is updated 7 2 Configuration via teach button 1 sensor 2 memory plug 3 teach button available as accessories order no E30405 T button No sensor may be connected gt Press the teach button for the indicated time the end of the time span is sig nalled by a change of the LED display following figures Change from Write protected to Read Write A READ WRITE B READ WRITE A LED display memory plug empty B LED display memory plug full 20 Change from Read Write to Write protected A LED display memory plug empty B LED display memory plug full A READ WRITE Oo w A LED display memory plug 21 8 Scale drawing Q Kwtoxt gt ma Dimensions in mm 1 connection for voltage supply and output signals 2 connection for sensor 22 9 Technical data IO Link m
Download Pdf Manuals
Related Search