Operating instructions Pressure sensor PN50xx 704789 / 00 05
Contents
1. 6 Menu 8 1 Menu structure l g S S R OF Hel JE d OP OF 8 2 Explanation of the menu SP1 rP 1 Maximum minimum value for system pressure at which output 1 changes its switching status Output function for OUT1 e Switching signal for the limit values hysteresis function H or window function F normally open no or normally closed nc each Extended functions Opening menu level 2 Standard unit of measurement for the system pressure UK 9 Parameter setting During the parameter setting process the unit remains in the operating mode It continues its monitoring function with the existing parameters until parameter setting has been terminated 9 1 Parameter setting general Each parameter setting requires 3 steps Selecting parameter gt Press Mode Enter until the reque GAGE D sted parameter is displayed ka Setting the parameter value gt Press Set and keep the buton pressed Modefenter Set gt Current setting value of the parame 4 ter bit flashes for 5 s gt After 5 s Setting value is changed incremental by pressing briefly or scrolling by holding pressed The numerical values are incremented continuously If the value is to be reduced Let the display move to the maximum setting value Then the cycle starts again at the minimum setting value Acknowledge parameter value gt Press Mode Enter briefly GHEE gt The parameter is displayed again DO The new s2. Read this document before installing the unit Ensure that the product is suita ble for your application without any restrictions e Non adherence to the operating instructions or technical data can lead to personal injury and or damage to property e In all applications check compliance of the product materials gt chapter 12 Technical data with the media to be measured e Use in gases at pressures gt 25 bar only after contacting the manufacturer ifm For units with cULus approval and the scope of validity cULus The device shall be supplied from an isolating transformer having a secondary Listed fuse rated as noted in the following table Overcurrent protection The Sensor shall be connected only by using any R C CYJV2 cord having suitable ratings 3 Functions and features The unit monitors the system pressure of machines and installations Applications Type of pressure relative pressure Order no Measuring range SEES IE Bursting pressure g rang overload pressure S bar PSI bar PSI PN5000 0 400 0 5800 600 8700 1000 14500 5 800 12 300 350 PN5002 0 100 0 1450 300 4350 650 9400 2175 30 5075 D I 110 145 145 75 1087 150 ait PN5006 0 25 0 383 20 290 a PN5007 01 Is 10 15 3 MPa bar 10 kPa x a Static and dynamic overpressures exceeding the indicated overload pres sure are to be avoided by taking appropriate measures T
3. programming button 12 Technical data Operating voltage V Current rating mA Current consumption mA Reverse polarity and overload protected Short circuit protected Watchdog Voltage drop V SNS Ta EN WINGS seakan sak ain naka laen Dena gada Kae aan tener deca Wa a a aa gada NE ak aaa NGANA 0 3 Switching frequency Hz max 170 14 Accuracy deviations in of the span Accuracy of switch point Characteristics deviation Hysteresis Repeatability with temperature fluctuations lt 10K Long time stability in of the span per year Temperature coefficients TEMPCO in the compensated temperature range 0 80 C in of the span per 10 K greatest TEMPCO of the zero point of the span Materials wetted parts Stainless steel 3039522 ceramics FPM Viton Housing material Stainless steel 304915 stainless steel 316L 1 4404 PC Makrolon PBTP Pocan PEI FPM Viton 2 Protection Protection Insulation resistance MQ gt 100 500 V DC Shock resistance 9 50 DIN IEC 68 2 27 11ms Vibration resistance g 20 DIN IEC 68 2 6 10 2000 Hz SWING TITI CYCLES EE 100 million Operating temperature C 20 80 UB lt 32 V 20 60 UB gt 32 V Medium temperature C 25 80 Storage temperature C 100 EMC EN 61000 4 2 ESD e 4 8KV EN 61000 4 3 HF radiated e 10 V m EN 610004 4 EE 2 KV EN 610004 5 SUJE 5 iisagean anangeng naa aaa adan gk na rae an Ei AEE raad
4. A 704789 00 05 2010 ifm electronic Operating instructions Pressure sensor efeckEorsoo PN50xx Contents E ay MEIER 3 E ase an D 3 lee HOS E 3 3 Functions and features 4 d FONCION eee A A 5 4 1 Processing of the measured agnals eee eee c c Ke INN MANN EES 5 gt WAS te AU OM E 6 G EIOCIICAl COMME TEE 6 7 Operating and display element sese eee eee eee eee 7 E leegen 8 St Teater 8 92 EXD Anatom DOE 9 H Parameter setting sese 10 9 1 Parameter setting general sees esse ereenn 10 9 2 Configuring the display optional 12 9 3 Setting ThE DUDUL Signal sasanak akasa agan aeea A ANAN LANG ANA KANAAN a ag daa 12 9 3 1 Setting the output function E 12 9 3 2 Setting the switching limits sese sese esse eee eee 12 OA User settings optional aecaieaii ee 12 9 4 1 Setting the delay time for OUT sese 12 9 4 2 Setting the damping for OUT 12 9 9 SOR el E 19 9 5 1 Reading the min max values for the system pressure 13 ee le ener KAN NA tert eters a E ters ree eee 13 10 1 Read the set parameter values sese eee 13 UE aU ds e E A E E E T 13 T1 Scale drawing EE 14 Kr le EE 14 SEENEN gae gan MIA eg Kap KANA 16 d ASCE STUN ee 17 1 Preliminary note 1 1 Symbols used gt Instruction gt Reaction result Designation of buttons switches or indications Cross reference Important note Non compliance can result in malfunctions or interference UK 2 Safety instructions e
5. c fig 2 The width of the window can be set by means of the distance between SP1 and rP1 SP1 maximum value rP1 minimum value P system pressure HY hysteresis FE window 5 Installation Before mounting and removing the sensor make sure that no pressure is applied to the system gt Insert the unit in a GA process connection gt Tighten firmly 6 Electrical connection The unit must be connected by a qualified electrician The national and international regulations for the installation of electrical equipment must be adhered to Voltage supply to EN50178 SELV PELV gt Disconnect power gt Connect the unit as follows switching output for pressure monitoring not connected Core colours of ifm sockets 1 BN brown 3 BU blue 4 BK black 7 Operating and display elements OG O OOOO 1 to 8 Indicator LEDs LED 1 to LED 4 system pressure in unit of measurement as indicated on the label LED 4 not used for units with 3 adjustable units of measurement LEDs 5 to 7 not used LED 8 switching state of the output 9 Alphanumeric display 4 digits Indication of the current system pressure Indication of the parameters and parameter values 10 Set pushbutton Setting of the parameter values scrolling by holding pressed incremental by pressing briefly 11 Mode Enter pushbutton Selection of the parameters and acknowledgement of the parameter values
6. etting value is stored Set more parameters gt Start again with step 1 Finishing parameter setting gt Press Mode Enter several times until the current measured value is displayed or wait for 15 s gt The unit returns to the operating mode 10 e Changing from menu level 1 to menu level 2 gt Press Mode Enter until EF is displayed H the submenu is protected with an ac cess code Cod1 flashes in the display DDOD gt Press Set and hold it pressed until Modetnie Set BEF i i I the valid code no is shown gt Then briefly press Mode Enter Delivery by ifm electronic no access restriction gt Press Set briefly gt The first parameter of the submenu is HOHE Dina displayed here Uni Ne Se e Locking unlocking The unit can be locked electronically to prevent unintentional wrong settings gt Ensure that the unit is in the normal operating mode 8088 gl ae _ gt Press Mode Enter Set for 10 s Vodite sa gt Loc is displayed lg During operation Loc is displayed briefly when you try to change parameter values For unlocking gt Press Mode Enter Set for 10 s BEBE el Jocl gt uLoc is displayed SS Se l On delivery Unlocked e Timeout H no button is pressed for 15 s while the parameters are being set the unit returns to the operating mode with unchanged values 9 2 Configuring the display optional gt Select Uni and
7. gan 0 5 1KV EN 61000 4 6 let 10 V 1 to EN50178 SELV PELV 2 in addition PTFE for PN5003 PN5007 3 for PN5000 PN5002 for PN5003 PN5007 BFSL Best Fit Straight Line LS Limit Value Setting 15 12 1 Setting ranges LO LO LO y D la leal l UW lell lt Ola Sl lc 0 lt RE T SN o eet SING es Z 1 1 ae SD T T LO co O d LO lt N Bei N ald Lea le N N llel cs o O K LI cs vc O o CO l CO D elo elooiolelc oeloigleie CIN A SIDiqgiz oja aja l 1 HR Re Qja s ce a SSMN CHE Ee um zoosna eme TI SES increments AP 16 13 Factory setting Factory setting 25 VMR 23 VMR bAr mbAr the indicated percentage of the final value of the measuring range VMR of the corresponding sensor in bar mbar is set More information at www ifm com 17
8. he indicated bursting pressure must not be exceeded Even if the bur sting pressure is exceeded only for a short time the unit can be destroyed NOTE Risk of injury Use in gases at pressures gt 25 bar only after contacting the manufacturer ifm High pressure units 400 bar are supplied with an integrated damping device to comply with the regulations for UL approval and to avoid any risk of injury in case of bursting when bursting pressure is exceeded lt When the damping device is removed the damping device can become unus able e When the damping device is removed the unit can no longer be used under UL conditions If you have any questions please contact ifm electronic s sales specialists 4 Function 4 1 Processing of the measured signals lt The unit shows the current system pressure on its display e t generates 1 output signal according to the parameter setting OUT1 switching signal for pressure limit values 4 2 Switching function OUT1 changes its switching state if it is above or below the set switching limits SP1 rP1 The following switching functions can be selected UK e Hysteresis function normally open OU1 Hno fig 1 e Hysteresis function normally closed OU1 Hnc fig 1 First the set point SP1 is set then the reset point rP1 at the requested distance e Window function normally open OU1 Fno fig 2 e Window function normally closed OU1 Fn
9. set the unit of measurement bar mbar MPa kPa PSI for PN5007 in addition inHg gt Select diS and set update rate and orientation of the display d1 Update of the measured value every 50 ms d2 Update of the measured value every 200 ms d3 Update of the measured value every 600 ms rd1 rd2 rd3 Display like d1 d2 d3 rotated by 180 OFF The display is deactivated in the operating mode 9 3 Setting the output signal 9 3 1 Setting the output function gt Select OU1 and set the switching function Hno hysteresis function normally open Hnc hysteresis function normally closed Fno window function normally open Fnc window function normally closed 9 3 2 Setting the switching limits gt Select SP1 and set the value at which the output switches SPI gt Select rP1 and set the value at which the output switches back rP1 is always lower than SP1 The unit only accepts values which are lower than SP1 9 4 User settings optional 9 4 1 Setting the delay time for OUT1 dS1 switch on delay dr1 switch off delay gt Select dS1 or dr1 set value between 0 1 und 50 s at 0 0 the delay time is not active 9 4 2 Setting the damping for OUT1 gt Select dAP set value dAP value response time between pressure change and change of the switching status in milliseconds ms The following values can be set They define
10. the switching frequency f of the output a o 6 0 7 0 GHE rival wo wo eo footw elsf2 1 12 9 5 Service functions 9 5 1 Reading the min max values for the system pressure gt Select HI or LO press Set briefly HI maximum value LO minimum value Delete memory gt Select HI or LO gt Press Set until is displayed gt Press Mode Enter briefly LO is available only for PN5004 10 Operation UK After power on of the supply voltage the unit is in the Run mode normal operati on It carries out its measurement and evaluation functions and generates output signals according to the set parameters Operation indication chapter 7 Operating and display elements 10 1 Read the set parameter values gt Press Mode Enter briefly until the requested paramerter is displayed gt Press Set briefly gt The unit indicates the corresponding parameter value for 15 s After another 15 s the unit returns to the Run mode 10 2 Fault indication OL overload pressure measuring range exceeded UL underpressure range measuring range below the minimum value SC1 short circuit in OUT1 the output is switched off as long as the short circuit exists Err flashing internal fault The faults SC1 and Err are indicated even if the display is deactivated 13 11 Scale drawing Dimensions are in millimeters dimensions for PN5000 1 display 2 LED s 3
Download Pdf Manuals
Related Search