INSTALLATION MANUAL SIBAKZOS45
Contents
1. To This Position Hopper Assembly Not Shown for Clarity Step D Place Control Plate Assembly Over End of Lower Linkage as Shown in Inset opposite view assembled Figure 5 Figure 6 Step E Attach Control Plate Assembly To Frame Using M6x40 Bolts Rod To Be Flat Parallel With Ground This End Of Rod To Be Facing Upward V em geg SC Hi jj ui GI GO un a we es ET SS ga ke 6 ee a A 1 ee EN AE D EI 7 ER ge bk KI pa pa a ey yi Iw pe Gi va ky io NN ep Sines x j a ea f ken a5 WCE 0 TT Br d be G E oc WT i g e o d Alkobel nv Westpoort 63 2070 Zwijndrecht Belgium BE 0462 837 676 T 32 3 219 09 86 F 32 3 219 37 14 info alkobel com www alkobel com p 3 5 Figure 7 F Attach Control Handle Assembly to Frame Using M6x40 Bolts G Remove Control Handle from Assembly Insert Upper Linkage into Control Handle Reattach Control Handle First Jam Nut List of parts Plate Fully Open and the Control Handle to H Thread First Jam Nut onto _Upper Linkage and Insert Linkage into Control Plate Assembly Secure Linkage with Second Jam Nut and Tighten Figure 8 NI J Attach Rear Deflector Using M6x20 Bolts Alkobel nv Westpoort 63 2070 Zwijndrecht Belgium BE 0462 837 676 T 32 3 219 09 86 F 32 3 219 37 14 info alkobel com www alkobel com p 4 5 ITEM QTY DESCRIPTIO2. BZTAKNSN ET SSN Cam m KEN db KOBE INSTALLATION MANUAL SIBAKZOS45 General Check the contents of the box with the parts list to make sure all components are included Tools needed for assembly 2 10 mm wrenches 2 Y2 in wrenches Attaching the Handle Linkage Plate Assembly and Lower Linkage Figures 2 6 A Remove contents from box and place the preassembled portion of the spreader upright on its wheels Slide the Handle onto the spreader frame amp line up the holes Carefully insert the Lower Linkage into the Restrictor Plate underneath the Hopper as shown The Lower Linkage has two bent ends amp the Upper Linkage has one threaded end D Insert the other end of the Lower Linkage into the front hole on the Linkage Plate Assembly Attach the Linkage Plate Assembly and Handle to the Frame using two M6x40 bolts as shown Figure 6 shows the lower linkage assembled for reference Note The Lower Linkage must be attached to the restrictor and the Linkage Plate Assembly before the Assembly is attached to the frame If the Linkage Plate Assembly is attached to the Frame without the Lower Linkage the Lower Linkage will be very difficult to assemble and may cause the restrictor plate to be broken during assembly Attach control Handle Assembly Upper Linkage amp Rear Deflector Figure 7 amp 8 F Mount the Control Handle Assembly to the Handle using two M6 x 40 bolts as shown G Insert the Upper Linkage into th
3. N 1 Frame 2 1 Handle 3 1 Hopper Assembly Hopper Restrictor Plate Assembly 4 1 Spinner Assembly Spinner Shaft Assembly Spinner Bracket Bushing Spacer 5 1 Deflector Assembly 6 1 Rear Deflector Assembly 7 1 Control Handle Assembly 8 1 Linkage Plate Assembly 9 1 Upper Linkage 10 1 Lower Linkage 11 2 Wheels 12 1 Axle 13 1 Drive Gear 14 2 Hopper Support Bracket 15 1 Screen 16 1 Spinner Shaft Support 17 4 Axle Bushings 18 1 Agitator Pin 19 1 Hardware Bag 1 Rain Cover Alkobel nv Wesipoort 63 2070 Zwijndrecht Belgium BE 0462 837 676 T 32 3 219 09 86 F 32 3 219 37 14 info alkobel com www alkobel com p 5 5
4. e Control Handle as shown H Thread one Jam Nut so that the Restrictor Plate underneath the Hopper is fully open when the Control Handle is at 30 Assemble the second jam nut in this position to lock the linkage in place Verify that the Restrictor Plate may be fully closed by pushing the Control Handle forward J Using two M6x20 bolts attach the rear deflector Final Assembly A Check And Tighten All Fasteners Make sure the Pinion and Gear mesh well and turn freely when pushing and pulling the unit B Place the Screen in the hopper C Install the Rain Cover on the hopper Operation d Before filling the Hopper ensure that the Resitrictor Plate is fully closed and the screen is in place 2 Move and tighten the stop bolt to the desired setting 3 Begin moving forward with the spreader Alkobel nv Westpoort 63 2070 Zwijndrecht Belgium BE 0462 837 676 T 32 3 219 09 86 F 32 3 219 37 14 info alkobel com www alkobel com p 1 5 SAAD 4 Pull the Control Handle back to the stop bolt to open Restrictor Plate and allow material to flow 5 Before stopping push the Control Handle fully forward to stop flow Maintenance 1 The Hopper and Spinner should be completely emptied and cleaned before storage 2 The Spreader should be washed and dried before storage 3 Check that the Restrictor Plate and Linkage move freely Clear out any debris between the Restrictor Plate amp the Hopper 4 Check
5. that there is no debris in the Gears amp that they move freely 5 Check torque of all fasteners on a monthly basis Operation Notes 1 The spreader is designed to be operated at a brisk walking pace approx 3 mpH Walking slower or faster will alter the distribution pattern amp amount of the material as will the moisture content of the material amp other environmental factors 2 Grease may be applied to the Pinion amp Large Drive Gear as desired Warning When filling hopper make certain there are no large objects within the material Objects larger than the openings in the Screen may cause the spreader to clog or even damage the drive system Never leave material in the hopper when not in use Figure 1 Contents of Box AT t Figure 2 Control Handle _ mE iti teil Linkage Plate Assem e Screen x 4 io er ba 1 Handle Assembly a EN gutta d AN SM Step B Slide Ve j Linkage h a Handle Onto Frame _ d d And Line Up Holes Spreader eh n f As CM m d oe Zem aN Lower Linkage es os Ze d g eg Fae cate ee LL i Rain Cover And Hardware Kit Are Not Shown Alkobel nv Westpoort 63 2070 Zwijndrecht Belgium BE 0462 837 676 T 32 3 219 09 86 F 32 3 219 37 14 info alkobel com www alkobel com p 2 5 Figure 3 Figure 4 Step C Insert Lower Linkage Into Restrictor Plate This End To Be Installed Down Into Control Plate And Then Rotated
Download Pdf Manuals
Related Search