Home

user's manual - Eki'p Dental

1. SE EXPLANATION E32 2 IMUX software is not compatible IMUX is of new type with MCB software E32 3 IMUX data error cable short circuit E32 4 IMUX communication error E32 5 Wrong IMUX type or wrong unit type E33 1 Syringe select valve short circuit E33 2 Instrument 1 select valve short circuit E33 3 Instrument 2 select valve short circuit E33 4 Instrument 3 select valve short circuit E33 5 Instrument 4 select valve short circuit E33 6 Instrument multiplexer related error messages E33 7 Drive Cooling air valve short circuit E33 8 Air coolant valve short circuit E33 9 Water coolant valve short circuit E34 Not used or not in the manuals E34 1 Syringe select valve open circuit E34 2 Instrument 1 select valve open circuit E34 3 Instrument 2 select valve open circuit E34 4 Instrument 3 select valve open circuit E34 5 Instrument 4 select valve open circuit E34 6 Instrument multiplexer related error messages E34 7 Drive Cooling air valve open circuit E34 8 Air coolant valve circuit E34 9 Water coolant valve circuit E35 1 Drive Cooling air pressure sensor output lt 0 2 V E35 2 Air coolant pressure sensor output lt 0 2 V E35 3 Water coolant pressure sensor output lt 0 2 V E35 4 Differential pressure sensor output lt 0 2 V E36 1 Drive Cooling air pressure sensor output gt 5 V E36 2 Air coolant pressure sensor output gt 5 V
2. HELP CODE MEANING ACTION OR EXPLANATION HE210 Software update Installing to Control panel Do not turn the power off while the software is bootloader sw DO NOT TURN POWER being updated OFF HE212 Software update Installing to Control panel Do not turn the power off while the software is application sw DO NOT TURN POWER being updated OFF HE214 Software update Installing to Control panel Do not turn the power off while the software is application sw DO NOT TURN POWER being updated OFF HE216 Software update Downloading from server Do not turn the power off while downloading DO NOT TURN POWER OFF software from the server HE218 Software update Installing to Main PCB Do not turn the power off while the software is DO NOT TURN POWER OFF being updated END Flushing completed Remove syringe from flushing holder and return it to console If syringe is removed return it to flushing holder DOOR Cuspidor door is open Close the door FC LD Move foot control pedal to leftmost position Move the foot control pedal to the leftmost Press pedal down and hold While holding position Press the pedal down and hold push centre knob briefly in chair up direc While holding push the centre knob briefly in tion the chair up direction FC LU Move foot control pedal to leftmost position Move the foot control pedal to the leftmost and hold While holding push centre knob position and hold While holding push
3. PM fibre optic turbine hose S Satelec MiniLED polymerisation light Satelec MiniLED Supercharged polymerisation light Satelec Newtron LED scaler Satelec Newtron scaler W amp H EM E8 brushless micromotor with LED W DW WOW w WW D DTD W WO WW w v v w v w WO wu DD Durr VistaCam PAL BF Planmeca Lumion LED polymerisation light BF Sopro 617 PAL BF Sopro Life PAL BF User s Manual Planmeca Compact i Classic v2 95 TECHNICAL SPECIFICATIONS 24 2 Dimensions Positioning of patient dentist and assistant The following picture shows an example of how to position the dentist and assistant during treatment The patient must always be positioned in the patient chair with arms and legs resting on the upholstery The dentist and assistant can move within the areas marked in the picture below NOTE The following picture is an example only and presents one possible scenario The actual positioning of dentist and nurse depends on the used working method treatment situation region etc and can therefore not be explicitly stated in this manual 96 Planmeca Compact i Classic v2 User s Manual TECHNICAL SPECIFICATIONS Patient area The patient area is 1 5 m 59 1 in each direction from the dental unit The external PC its keyboard and mouse as well as Planmeca ProSensor s power supply and the Planmeca ProX generator assembly must b
4. E54 3 Pedal too far from sensors channel A E54 4 Pedal too far from sensors channel B E54 5 Sensor plate is tilted too much to either side checksum error E54 6 Sensor plate is too close to PCB channel A E54 7 Sensor plate is too close to PCB channel B E54 8 Foot control re trigger error E54 9 Foot control calibration error E55 Foot control related error messages Table 8 Operating light related error messages ERROR CODE EXPLANATION E56 Operating light erroneously connected or short circuit in push button E57 Incompatible Singled software E58 Operating light bulb burned out Table 9 Separator system related error messages ERROR CODE EXPLANATION E59 1 Separator reports functional error E59 2 Separator reports functional error E60 Separator is not responding or separator cable is faulty E61 Separator is flooded with too much water E62 Newly attached separator is of new type and cannot be controlled by MCB E63 1 WMS seems to be installed although it should not be according to service mode E63 2 No WMS is installed although it should be according to service mode Table 10 Patient chair related error messages ERROR CODE EXPLANATION E64 Seat pos potentiometer or its cable is faulty or disconnected E65 Lift motor doe
5. NOTE CAUTION NOTE excluding syringe is operated The operating light intensity will decrease slightly when the chair is moving The patient chair can be operated remotely with the Planmeca Romexis Clinic Management module Before operating the chair remotely make sure that the chair movements cannot cause harm to the patient or to the user of the dental unit For detailed information see Planmeca Romexis Clinic Management user s guide When driving the chair near the upper limit make sure that the console arm does not press or hit the patient To drive the backrest down press and hold the A button until the chair reaches the required position To drive the backrest up press and hold the B button until the chair reaches the required position To drive the chair up press and hold the C button until the chair reaches the required position Make sure that the bowl is not above the patient chair when driving the chair upward User s Manual Planmeca Compact i Classic v2 35 OPERATING PATIENT CHAIR 14 2 Automatic operation GR AW To drive the chair down press and hold the D button until the chair reaches the required position Alternatively you can adjust the position of the chair with the foot control Push and hold the centre knob in the
6. Planmeca Compact i Classic v2 user s manual PLANMECA TABLE OF CONTENTS Bi INTRODUCTION E 1 2 ASSOCIATED DOCUMENTATION i rrrrrvvvvnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 1 3 TRAINING E 2 4 PREVENTIVE MAINTENANCE ooo Reese ege 2 5 SYMBOLS ON PRODUCT LABELS rvrvvvvvvvnvvvrvennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 2 6 FOR YOUR SAFETY tee ee 4 Gal SAN PENSEL Eed 4 6 2 Safety EE 6 6 3 Stopping chair movements quickly ENNEN 7 7 PLANMECA COMPACT I CLASSIC V2 DENTAL UNIT i nnnnnnnnnnnnnnnnnnnnnnnnnnnnn 8 7 1 Dental unit CONTIGUIATIONS E 8 7 2 Detachable p rts inrcr enna EE oK aE KETE EE aK A Eet 10 EC E EE 13 Te MN ee ee 14 8 INSTRUMENT SYSTEM eebe 15 8 1 Over the Patient OP delivery arm ENEE 15 Se gl e Ee EE 16 S29 QUICK connector NOSES EE 18 04 FITS CEM EE 19 8 5 strument LOGIC sie otace ee ege ee n 20 05 Pay CADIS se ee 21 9 SUCTION SS EEN dee eege Nee 23 CN Een EE 23 92 SUCTION ren e 23 9 3 Suction nee 24 10 PATIENT CHA R uses 25 10 1 Trendelenburg he WEE 25 10 2 PRIUS S siirrt gek eege ege EEEE 25 10 3 Nee eebe e deene ee Wedel tut 27 11 CONTROL PANEL ass 29 11 1 Dentists controlpanel aa aaverdessedekr need dandnen 29 11 2 Optional assistan s eer EE 30 12 FOOT EONIROL ors 31 12 ON e ge let 31 13 SWITCHING UNIT ON AND OFF i nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnr 34 14 OPERATING PATIENT CHAIR Lises 35 141 7 Manual operatorn EE 35 142
7. the dental unit and the chair The only difference between the dentist s and the assistant s control panel is that on the assistant s control panel the Cup fill bowl rinse button has been replaced by separate cup fill and bowl rinse buttons Program button and indicator light Display Rinsing position button and indicator light Chair buttons Unit buttons Instrument buttons and indicator lights 30 Planmeca Compact i Classic v2 User s Manual FOOT CONTROL 12 FOOT CONTROL 12 1 Introduction The Planmeca Compact i Classic v2 dental unit has one integrated foot control that operates the instruments the unit and the chair Centre knob Left side Right side knob knob Pedal CAUTION The foot control is a precision instrument Do not stand on or apply unnecessary force to the foot control and its knobs Two foot control pedals are available the standard pedal and a slightly wider pedal that functions like a gas pedal when you drive the instrument That is the further down you push the pedal the higher the instrument speed is The functional differences between the standard pedal and the wide pedal only apply to the micromotor turbine Wide pedal and scaler and are described in the table below Standard pedal Function Standard pedal Wide pedal Increase instrument speed Push pedal to left right Push pedal down Change instrument spray type Push pedal down b
8. and are recalled when the instrument is reconnected A scaler requires additional electronics and the scaler type can not be changed without changing electronics Make sure that the hoses are properly connected to the console to avoid any leakage Always make sure that the instrument hose is correct for the used instrument The control system identifies the instrument hose not the instrument The control system does not recognise the instrument change for example the replacement of a turbine with an air motor If the outer casing of the instrument hose is broken the entire hose must be replaced although the hose itself might still be functioning The instrument sealings must be correct and unbroken and the instrument must be attached properly to the hose connector The leakage between the instrument and the connector causes leakage air to drift into the hose lining 18 Planmeca Compact i Classic v2 User s Manual INSTRUMENT SYSTEM 8 4 Instruments 8 4 1 Instrument spray 8 4 2 Automatic chip blow 8 4 3 Fibre optic light The instrument console has five instrument positions You can program each instrument so that the following functions will where applicable either be on or off when the instrument is picked up from the instrument console e instrument spray automatic chip blow e fibre optic light e reverse rotation micromotor only e quickstart air driven instruments only The type or mag
9. e Installation manual publication number 10029964 For service personnel Describes how to install the intraoral X ray unit e Technical manual publication number 10029965 For service personnel Gives instructions for service situations For a full list of accessories refer to the Planmeca product price list A hands on user s training is given in connection with the dental unit installation 4 PREVENTIVE MAINTENANCE To guarantee the unit s proper operation the unit must be checked and serviced once a year by a qualified Planmeca service technician 5 SYMBOLS ON PRODUCT LABELS A Type B equipment Standard IEC 60878 Type B applied parts for specified dental instruments Standard IEC 60878 Type BF applied parts for specified dental instruments Standard IEC 60878 Alternating current Standard IEC 60878 Attention consult accompanying documents Standard ISO 7010 General warning Standard ISO 7010 2 Planmeca Compact i Classic v2 User s Manual SYMBOLS ON PRODUCT LABELS A p A Turn the main switch off before servicing the unit LBL G 012 A Warning crushing hazard hand Standard IEC 60878 Protected against dripping water Standard IEC 60529 Separate collection for electrical and electronic equipment according to Directive 2002 96 EC WEEE Date of manufacture Standard IEC 60878 Protective earth Standard IEC 60878 Radio certi
10. perform dental treatment when either or both of these are detached e Balanced instrument arms e Headrest The following detachable components are not critical to operation The user can perform dental treatment even if a wrong similar part is fitted e Hygienic membrane 10 Planmeca Compact i Classic v2 User s Manual PLANMECA COMPACT i CLASSIC V2 DENTAL UNIT e Armrests e Flushing holder e Glass fill tube e Bowl Keay User s Manual Planmeca Compact i Classic v2 11 PLANMECA COMPACT i CLASSIC V2 DENTAL UNIT e Side cover plate for cuspidor e Suction hoses 12 Planmeca Compact i Classic v2 User s Manual PLANMECA COMPACT i CLASSIC V2 DENTAL UNIT 7 3 Bowl The glass bowl is attached to the top of the cuspidor It can be rotated 110 around its axis according to the figure below NOTE Always place the bowl in rest position NOTE Make sure that the bowl is not above the patient chair when you drive the chair upward To avoid a collision between the patient chair and the bowl when driving the chair upward position the bowl within this area Rest position If the bowl assembly for some reason comes off the cuspidor you can put it back as follows 1 Place the ring to the underside of the bowl assembly as shown in the picture in step 2 User s Manual Planmeca Compact i Classic v2 13 PLANMECA COMPACT i CLASSIC V2 DENTAL UNIT 2
11. tee El EE 36 14 83 RINSING Kee UL EE 38 15 OPERATING DENTAL UNIT eege erte 39 151 OW Rame GE 39 15 2 UID rejeni ee ates had eal e Dea tea Ms Moca a R eA abla 39 User s Manual Planmeca Compact i Classic v2 i TABLE OF CONTENTS 15 3 Door open assistant call Lauismavudggareenmam nm henieeeieeeds 40 15 4 Planmeca SingLED operating light sc cite cot seston tonto heemeenina ana ghetto 41 16 OPERATING INSTRUMENTS eege ESEEEEEEESEEEEEeek 42 16 1 gt MIGFOMOLON EE 42 16 2 TUINE EE 44 163 EE E E MSN Te ees 46 16 4 Planmeca Lumion polymerisation light renrnnnnnnnnnrrnnnnnnnnrnnnnrrrrnnnnnnrnrnrrrrnnnnenerrennnnn 48 16 5 Intraoral camera EE 49 17 PROGRAMMING iht degt 50 EEN WEN nu ge ee 50 17 2 Automatic chair positions raude ses decmeseeugucedeadvevssvohe east 51 17 3 lant E 52 174 ASTM EE 53 175 Scaler end seni Seen ugeet Eed Eege 54 17 6 Fibre optic light LED light EE 55 17 7 Planmeca Lumion polymerisation light renrnnnnnnnnnrrnnnnnnnnrnnnnrrrrnnnnnnarnnrrrvnnnnennrrennnnn 56 17 8 Duration of bowl rinsing and cup filling 0 eect eee eee ee ee ee etree eeeeeaaeeeeeeeeneeeaa 57 17 9 Intensity of operating light EE 58 17 10 Duration of door open assistant call ENEE 59 18 UNIT ADJUSTMENTS egene 60 18 1 Adjusting cup fill and bowl rinse flow rates rrrnnnrrrnnnnnnnnnnnrrrrnnnnnnrrrrrnnnrnnnnnnrrrrnnnnnn 60 19 CLEANING 61 192 SUCTION SY SIGINT 2 dekte kadre 61 19 27 BOGE HSA 64 19 3 Instrument hose
12. Change the parameter air water to be adjusted by pressing instrument spray or by pushing the foot control pedal briefly down 6 Adjust the flow rate with the foot control 7 Press Program 52 Planmeca Compact i Classic v2 User s Manual PROGRAMMING 17 4 Chip blow Air Water NOTE Activate the instrument Press Program Press Chip blow The flow of both air and water can be adjusted The text CA on the display indicates that the chip air is adjusted The text CH indicates that the chip water is adjusted The minimum value of both parameters is 0 no flow and the maximum 100 marked as F 4 Adjust the flow rate with the foot control 5 Change the parameter air water to be adjusted by pressing Chip blow or by pushing the foot control pedal briefly down 6 Adjust the flow rate with the foot control 7 Press Program The type of manual chip blow does not depend on the type of the automatic chip blow but is dry as a factory default The manual chip blow can be set to be dependent on programming contact your Planmeca dealer User s Manual Planmeca Compact i Classic v2 53 PROGRAMMING 17 5 Scaler This procedure applies when you are adjusting the water spray for the scaler For instructions on how to adjust the instrument spray for other instruments see section 17 3 Instrument spray on page 52 1 Activate the instrument 1 Press Prog
13. Compact i Classic v2 61 CLEANING 19 1 3 After the working day 1 Disinfect the suction system by using Orocup 2 When the suction system has been rinsed autoclave the suction handpieces Orocup The following describes how to disinfect the suction system with Orocup 1 Mix the cleaning solution as follows Pour 20 ml Orotol Plus liquid using the mark on the top into the rinsing bottle Add 1 water and shake well Rinsing bottle NOTE Do not use dish washing detergents 2 Place the rinsing bottle for example Orocup on a flat surface table or floor 3 Remove the suction handpieces from their holders and push them onto the inserts inside the cap of the rinsing bottle Allow the bottle to empty 4 Return the suction tubes back to the holder right after Orocup has been emptied Do not use suction only for air 5 Replace the exchangeable parts filters etc the next morning 19 1 4 Weekly cleaning procedures 1 If your dental unit is equipped with a Durr amalgam separator or D rr VSA separator open the bowl valve by holding your finger on the Program button for about 5 seconds until the suction starts The valve will close automatically after about 15 seconds 2 Mix 20 ml Orotol Plus liquid with 1 I water and shake well Pour the solution into the bowl 3 Let the solution affect overnight Rinse the suction system the next morning with 2 of water 4 Rinse the bowl with water the next m
14. D5 or D6 short circuit or either of the 24V electronics fuses F3 or F4 has blown on the MCB Chair instrument and headrest control not allowed E11 5 Separator fuse F5 has blown on the MCB Chair instrument and headrest control not allowed E11 6 Water heater fuse F6 has blown on the MCB Chair instrument and headrest control not allowed E11 7 Syringe heater fuse F7 has blown on the MCB Chair instrument and head rest control not allowed E11 8 Curing light fuse F8 has blown on the MCB Chair instrument and headrest control not allowed E12 1 SELV voltage too low below 30V Chair instrument and headrest control not allowed E12 2 SELV voltage too high above 39V E13 Mains frequency outside acceptable range E14 IPS temperature measurement sensor error E15 IPS heatsink is running too hot on MCB E16 Attached scaler electronics is of new type 86 Planmeca Compact i Classic v2 User s Manual HELP amp ERROR MESSAGES Table 2 Power supply related error messages SE EXPLANATION E16 1 New type of scaler electronics is attached to MCB E16 2 New type of scaler electronics is attached to IMUX E16 3 Scaler electronics slot does not match with scaler hose connection E16 4 Other instrument than scaler is connected to slot where scaler electronics is E17 Power Supply rela
15. Make sure that the peg goes into the slot as shown in the picture below Ring IMG 9514 jpg 3 Push the bowl downwards at the same time making sure that no cables are squeezed 4 Turn the bowl assembly into place You will know that it is in place when you hear the clicking sound of the micro switch 7 4 Monitor The monitor can be moved from its handle CAUTION Do not allow the patient to grab the monitor handle when getting seated or getting up from the patient chair Clean the monitor according to the instructions in section 19 10 Monitor on page 70 NOTE Never spray water on the monitor or the PC For more information see the monitor s user s manual 14 Planmeca Compact i Classic v2 User s Manual INSTRUMENT SYSTEM 8 INSTRUMENT SYSTEM 8 1 Over the Patient OP delivery arm The OP delivery arm is attached to the top of the dental unit and swings over the chair CAUTION Do not lean on the OP delivery arm The instrument console can be positioned using the handles on the console The rotation area of the delivery arm is presented in the illustrations below The items do not need to be locked into position The following presents the OP delivery arm with balanced instrument arms WA oF Cc H NN ARY oe The following presents the OP delivery arm with hanging tube instruments Cufl3 16 2 eps User s Manual Planmeca Compact i Classic v2 15 I
16. NOTE As an option a surgical armrest is available The patient s arm can be strapped to the armrest when for example infusing saline solution Make sure that the patient does not lean on the armrest when getting in or out of the chair To move the armrest horizontally you must lift it slightly to unlock it To replace the right standard armrest with the surgical armrest you must first detach the standard armrest To do so lift the armrest slightly to unlock it and move the armrest to a 45 position When the armrest is in a 45 angle lift it straight up to remove it 1 Once you have removed the standard armrest place the surgical armrest on the spindle in a 45 angle push the armrest down and rotate in either direction until it locks into place 2 The surgical armrest is removed in the same way as the standard armrest 26 Planmeca Compact i Classic v2 User s Manual PATIENT CHAIR 10 3 Manual headrest 10 3 1 Adjusting height of headrest The height of the headrest can be adjusted by sliding it manually NOTE The headrest can only be pulled out as far as to the MAX mark 10 3 2 Adjusting headrest angle To adjust the angle of the headrest press the bar on the side of the headrest support to release the locking mechanism Manually set the headrest to the required angle and release the bar When adjusting the headrest should be supported by hand User s Manual Planmeca Compact
17. are programmed to zero no flow Enter the spray programming mode to set a flow other than zero For details see Technical manual section Instrument spray flow rates in chapter Touch panel functions 80 Planmeca Compact i Classic v2 User s Manual HELP amp ERROR MESSAGES HELP CODE MEANING ACTION OR EXPLANATION HE22 Main air water valve operation is not set to This is just a reminder that either of the main automatic A in SM 12 air 13 water valves is temporarily set to always be either on Reboot unit HE22 again Contact service or off although they should be set to auto matic n A HE23 Automatic manual chip blow cannot be used when sterile water function is selected HE24 Programming of selected setting is dis The programming of the selected setting is abled disabled Disable the protection using service mode n 0 For more information see Technical manual chapter Service mode HE25 Planmeca Compact e help message Swivel the patient chair with automatic legrest Patient chair cannot be driven into auto before driving the chair to the automatic posi matic chair position tion Check that the chair type in service mode n 103 is correct See service mode n 103 in Technical manual chapter Service mode HE26 Drive seat upwards then lower backrest If Drive the seat upwards before lowering the patient chair is attached to unit chair
18. chair from one position to another Obstructions in the patient chair s line of movement activate safety switches that stop the motorised movements The safety switches and their functions are described below 1 Backrest An obstruction between the backrest and the floor when driving down the chair and or the backrest stops downwards chair and backrest movements Remove the obstruction to resume normal operation 2 Chair bottom and lift adapter An obstruction between the chair and the floor stops downwards chair and backrest movements Remove the obstruction to resume normal operation 3 Legrest The position of the legrest is identified as locked or unlocked hangs freely Based on this information the chair can be driven lower when it is locked 4 Bowl The bowl is above the patient chair and stops upward chair movements Remove the obstruction to resume normal operation 5 Cuspidor door The patient chair up down movement is inhibited when the cuspidor door is open Also the operation of instruments is inhibited Close the door to resume normal operation LN ad HILDE a WA va es 6 Planmeca Compact i Classic v2 User s Manual FOR YOUR SAFETY 6 3 Stopping chair movements quickly NOTE The chair movements can be stopped quickly by e touching the chair buttons on the touch panel e kicking safety switch number 4 on the chair bottom e pushing the foot control
19. error E73 4 CPU EEPROM checksum programmed Replace CPU if error occurs often E74 1 RAM error External RAM test failure replace RAM E74 2 CPU RAM test failure replace CPU E75 1 CPU error WD reset E75 2 Illegal OP code E75 3 Illegal vector E75 6 Mains voltage failure E75 7 Clock monitor reset E76 MAIN CPU related error messages E77 Error in communicating with external device reserved for future use E79 IMUX water pressure cannot be released during WCS cycle Table 12 Headrest related error messages Fe EXPLANATION E80 1 Motorised headrest is not found according to service mode configuration E80 2 Motorised headrest is found but is not set in service mode configuration E80 3 Headrest joystick dentist side stuck or cable broken User s Manual Planmeca Compact i Classic v2 91 HELP amp ERROR MESSAGES Table 12 Headrest related error messages ERROR CODE EXPLANATION E80 4 Headrest joystick assistant side stuck or cable broken E81 Motorised headrest communication error may be too old or wrong software or loose cables or short circuit E81 1 Motorised headrest communication error E82 Headrest SW is incompatible with MCB SW E82 1 Headrest SW is incompatible with MCB SW E82 2 Incompatible headrest software E90 Water leak detected Table 13 Software upgrade error messages ERROR CODE EXPLANATION E99 Softwar
20. i Classic v2 27 PATIENT CHAIR 10 3 3 Adjusting headrest for children or short patients The headrest can be turned around and repositioned for better head support for children or short patients Pull the headrest out Turn it around so that the cushion faces backward and push the headrest back into the chair Turn the cushion around 180 counterclockwise Press the bar on the side of the headrest support to release the locking mechanism and position the headrest at the top of the chair ae Ni The headrest is now repositioned To adjust the angle of the headrest press the locking bar Manually set the headrest into the required position and release the bar When adjusting support the headrest with your other hand 28 Planmeca Compact i Classic v2 User s Manual CONTROL PANEL 11 CONTROL PANEL 11 1 Dentist s control panel Display Rinsing position button and indicator light Chair buttons Unit buttons Instrument buttons and indicator lights Program button and indicator light The control panel is located on the instrument console The dentist can use it to control and program the instruments the dental unit and the chair Also maintenance procedures can be started from the control panel The instrument buttons are used to operate and program the settings of the active instrument When the instrument is removed from its holder the indicator light on the instrument button di
21. presented below long push Micromotor Drive BC E EI micromotor d 7 Change spray ON OFF Ed Manual Chip Blow 32 Planmeca Compact i Classic v2 User s Manual FOOT CONTROL Turbine Drive y Drive Change spray ON OFF Manual Chip Blow Scaler Drive scaler Change spray ON OFF Polymerisation light Start 7 EN d Start LN works only in works only in unit controlled DN unit controlled instruments EX instruments Start Stop works only in unit controlled instruments Intraoral camera EE se Pett _ bat tee posal Save fei picture Planmeca Compact i Classic v2 33 User s Manual SWITCHING UNIT ON AND OFF 13 SWITCHING UNIT ON AND OFF The ON OFF switch is located at the rear of the unit base Press the switch once to turn the unit on Pressing the switch a second time will turn the unit off On off switch When the unit is switched on the ON OFF switch light is on The control panel briefly shows the software version 6 02 number 34 Planmeca Compact i Classic v2 User s Manual OPERATING PATIENT CHAIR 14 OPERATING PATIENT CHAIR NOTE All chair movements are blocked when an instrument 14 1 Manual operation CAUTION
22. restoration mode power range 50 is displayed as 1 When the scaler is the active instrument the working mode can be changed by pressing Chip blow The instrument s fibre optic light is either on or off when you pick up the instrument from the instrument console Whether the light is on or off as well as its intensity can be defined in the programming mode see section 17 6 Fibre optic light LED light on page 55 User s Manual Planmeca Compact i Classic v2 47 OPERATING INSTRUMENTS 16 4 Planmeca Lumion polymerisation light CAUTION The polymerisation light generates optical radiation and proper safety measures should be taken when using the instrument For detailed information please refer to OEM documentation To start the polymerisation cycle first select the desired curing mode by pressing the navigation button on the handpiece Then start the polymerisation cycle by pressing the start button on the handpiece The polymerisation cycle can be interrupted by pressing one of these buttons again To start the polymerisation cycle with the foot control first select the desired curing mode by pressing the navigation button on the handpiece Then push the foot control pedal to the right or to the left or down to start the polymerisation cycle The polymerisation cycle can be interrupted by pushing the foot control pedal to the right or to the left or down The length of the cycle is programmable s
23. rotates in the reverse direction the indicator light is amber Press Instrument spray to turn the instrument spray on or off When the indicator light is lit the spray is on and the spray of water air or both of them are flowing when operating the instrument The spray flow rate can be programmed See section 17 3 Instrument spray on page 52 Alternatively you can turn the instrument spray on off with the foot control Standard pedal Push the pedal down briefly to turn the instrument spray on off Wide pedal Push the pedal briefly to the left to turn the instrument spray on off The spray must be switched off when using an instrument without a waterline inside the handpiece 42 Planmeca Compact i Classic v2 User s Manual OPERATING INSTRUMENTS Momentary spray Automatic chip blow Manual chip blow NOTE Fibre optic light NOTE The instrument spray operated with the foot control can be disabled in the service mode in which case you can switch the spray on and off only from the control panel Contact your Planmeca dealer When you are driving the micromotor you can activate the momentary spray by pressing the foot control pedal down The spray will continue until you remove your foot from the pedal The momentary spray can be enabled and configured in the service mode contact your Planmeca dealer The momentary spray can not be activated with the wide foot control pedal Press Chip
24. the briefly in chair up direction centre knob briefly in the chair up direction FC CD Press foot control pedal down and hold Press the foot control pedal down and hold While holding push centre knob briefly in While holding push the centre knob briefly in chair up direction the chair up direction FC CU Keep foot control pedal in rest position cen Keep the foot control pedal in the rest position tre Push centre knob briefly in chair up centre Push the centre knob briefly in the direction chair up direction FC RD Move foot control pedal to rightmost posi Move the foot control pedal to the rightmost tion Press pedal down and hold While position Press the pedal down and hold holding push centre knob briefly in chair While holding push the centre knob briefly in up direction the chair up direction FC RU Move foot control pedal to rightmost position Move the foot control pedal to the rightmost and hold While holding push centre knob position and hold While holding push the briefly in chair up direction centre knob briefly in the chair up direction FC To exit foot control calibration mode press and hold down calibration switch for 4 sec onds 84 Planmeca Compact i Classic v2 User s Manual HELP amp ERROR MESSAGES 22 2 Error messages The following table lists the error messages which are mainly intended to assist the technician Table 1 Genera
25. the figure Turn also the cup fill tube above the bowl as shown in the figure Press the outer edge of the flushing holder cover and remove the cover Insert for syringe 2 Remove the hoses of the instruments to be flushed from the instrument arms instrument holders and place the instruments into the openings in the flushing holder If you are flushing the smaller round syringe or syringes max 2 remove the instrument cover and use the insert as shown in the figure before placing the syringe s in the flushing holder Lock the syringe s into place with a rotating movement when the syringe s is are in the holder Flushing holder cover The metallic syringe cover must be removed before placing the slightly thicker syringe into the flushing holder Note the orientation of the syringe It does not require an insert and must be placed in the holder as instructed below Syringe ps A clean_wu10 e User s Manual Planmeca Compact i Classic v2 67 CLEANING NOTE NOTE Balanced instrument arms Start the flushing cycle by bending the instrument arms of those instruments including syringe that are to be flushed to an angle of at least 90 and simultaneously pressing nstrument spray you will hear a signal tone and holding it for 6 seconds Release the button and instrument arms when you have heard a second and a third signal tone Hanging tube instruments Start the flushing cycle b
26. tube will cause the end of the handpiece to tilt slightly This action opens the handpiece valve allowing the suction to start You can stop the suction temporarily by straightening the suction handpiece with your thumb and forefinger If you temporarily put the suction handpiece down during dental treatment the suction will automatically stop as the force of the suction will straighten the handpiece 24 Planmeca Compact i Classic v2 User s Manual PATIENT CHAIR 10 PATIENT CHAIR Trendelenburg position 10 2 Armrests The patient chair is equipped with a fixed legrest Dark coloured clothes may cause coloured stains on the bright coloured upholstery Do not sit on the legrest If required the patient chair can be inclined from the horizontal position to the Trendelenburg position In the Trendelenburg position the legrest is in the horizontal position and the backrest is driven 4 from the horizontal position To drive the patient chair to the Trendelenburg position first drive the chair to horizontal position and press once more Chair position A to drive the backrest to 4 position Horizontal position Cufl3 7 2eps The right armrest can be moved 90 outwards Before you move the armrest you must lift it slightly to unlock it The armrest can be locked into the positions presented below User s Manual Planmeca Compact i Classic v2 25 PATIENT CHAIR Surgical armrest
27. CLASSIFICATION Class I type B and BF CHAIR LIFT AND BACKREST MOTOR OPER Intermittent operation ED 8 25 sec ON 300 ATION sec OFF CAUTION If the unit has been stored at temperatures below 10 C for more than a few hours time must be allowed for the unit to reach room temperature in the original packing before connecting the unit to the mains voltage 94 Planmeca Compact i Classic v2 User s Manual TECHNICAL SPECIFICATIONS 24 1 Instrument classifications e 7 The electrical classification of the instrument is marked on the instrument hose either as B or BF If there is no marking no electricity flows through the instrument The following lists the instruments that are available for the Planmeca Compact i Touch v2 dental unit and their electrical classification type Type B Type BF Instrument lt Oo Oo Air motor hose Autoclavable 3 way syringe BienAir MC 3 LED micromotor BienAir MX2 brushless micromotor with LED 2nd BienAir MX2 brushless micromotor with LED EMS No Pain LED scaler EMS No Pain scaler Ergo 3 way syringe angled Ergo 3 way syringe straight Ergo 6 way syringe angled Ergo 6 way syringe straight Ergo 6 way syringe with light straight LM PowerHand scaler LM ProPower SteriLED complete scaler with handpiece LM ProPower UltraLED scaler Planmeca Minetto brushless micromotor with LED PM fibre optic turbine hose
28. E36 3 Water coolant pressure sensor output gt 5 V E36 4 Differential pressure sensor output gt 5 V E37 Pressure sensor cable not properly attached to IMUX E38 Instrument multiplexer related error messages E39 Drive cooling air valve control servo cannot maintain pressure to instrument E40 Instrument multiplexer related error messages E41 Instrument multiplexer related error messages E42 Air coolant spray air control servo cannot maintain required pressure E43 Instrument multiplexer related error messages 88 Planmeca Compact i Classic v2 User s Manual HELP amp ERROR MESSAGES Table 5 Instrument multiplexer related error messages ERROR CODE EXPLANATION E44 Instrument multiplexer related error messages E45 Water coolant spray water control servo cannot maintain required pressure E46 Instrument multiplexer related error messages Table 6 Suction tube holder related error messages ERROR CODE EXPLANATION E47 Suction tube holder is of new type E47 1 Suction holder in branch 1 is of new type E47 2 Suction holder in branch 2 is of new type E48 1 No suction holders detected E48 2 Suction tube holder STH related error messages E48 3 Suction tube holder STH related error messages E48 4 Suction tube holder STH related error messages E49 1 Suction holder PCB or its cable is faulty in bra
29. HE11 Software download mode is on User s Manual Planmeca Compact i Classic v2 79 HELP amp ERROR MESSAGES HELP CODE MEANING ACTION OR EXPLANATION HE12 Unit s internal error reporting is disabled The unit operates normally but no errors are reported exhibition use Use service mode n 15 to turn error reporting back on See ser vice mode n 15 in Technical manual chapter Service mode for details HE13 Instrument cannot run because of patient security violation Return the foot control pedal once to the mid dle position to start the instrument Instru ments do not start if the standard foot control pedal is already pushed to the right or left when the instrument is picked up from the instrument console HE14 This dental instrument is not recognised new type of instrument To be able to operate this new instrument the MCB software must be updated See Techni cal manual section Upgrading software in chapter Parts replacement amp repair for details HE15 This key has no function at the moment Instruments Pick up a dental instrument before attempting to alter its settings or if the instrument is selected this function is not allowed with this instrument Other keys the unit does not have this function HE16 Operating light is dimmed and curing light can be used This feature enables easier work with compos ite materials minimising t
30. MENTS 16 5 Intraoral camera Freezing image NOTE NOTE Saving image In the 10 second cycle a signal tone is heard at the beginning and the end of the cycle In the 20 second cycle a signal tone is heard as the cycle starts after 2 seconds to confirm the start of the 20 second cycle after 10 seconds and at the end of the cycle When the Planmeca Lumion polymerisation light is in the independent mode it can not be controlled over the foot control Refer to the Planmeca Lumion manual of use and maintenance The intraoral camera is placed in the instrument console Activate the camera by picking it up from the console and bending the balanced instrument arm The camera is deactivated when you return it to the console The intraoral camera is operated with the foot control To ensure the proper function of the intraoral camera the dental unit must be switched on before you switch on the Planmeca Romexis application Push the foot control pedal to the left or right to freeze unfreeze the image When the image is frozen briefly push the foot control pedal down to save the image User s Manual Planmeca Compact i Classic v2 49 PROGRAMMING 17 PROGRAMMING 17 1 Introduction NOTE NOTE C NOTE AN o NOTE Most of the programming follows the same pattern If you are programming an instrument pick up the instrument from the instrument console If the instrument is operated during
31. NSTRUMENT SYSTEM 8 2 Instrument console 8 2 1 Instrument console with balanced instrument arms Roller NOTE The console can be equipped with up to five instruments The leftmost position is reserved for the syringe only The other instruments can be positioned in any order in the four remaining positions The instrument arms can be removed by pulling them out from their holders for example for cleaning The arms are replaced simply by pushing them firmly into their places When replacing the instrument hose to the roller bend the hook of the hose guide carefully and pass the hose over the roller The balance of the instrument arms can be changed according to the weight of the instrument and personal preferences Their flexibility can be adjusted as follows 1 Pull out the roller 2 Adjust the balance of the instrument arm by moving the roller to a desired position Note that the higher up you position the roller the lighter it is to bend the instrument arm 3 Push the roller back in to lock its position When balancing adjusting the instrument arms bear in mind that the instruments shall under no circumstances fall over the patient 16 Planmeca Compact i Classic v2 User s Manual INSTRUMENT SYSTEM 8 2 2 Instrument console with hanging tube instruments ps Cu_classic_19 e The console can be equipped with up to five instruments The leftmost position is reserved for the syringe
32. aces are changed 20 Planmeca Compact i Classic v2 User s Manual INSTRUMENT SYSTEM 8 6 Tray tables 8 6 1 Quick connect tray table The quick connect tray table is available for the instrument console with balanced instrument arms The tray table is attached to the mounting arm with a magnetic connector and can easily be attached and detached You can rotate the table 360 to the desired position The maximum load on the quick connect tray is 2 kilograms 4 4 Ibs The tray mounting arm is attached to the instrument console with a quick connector The tray assembly can be removed from the instrument console as follows Pull the ring of the locking mechanism outwards 1 and pull the tray arm away from its position 2 y eps CUFL tra The mounting arm can be attached to the instrument console by pushing it to its position y 2 eps CUFL tra User s Manual Planmeca Compact i Classic v2 21 INSTRUMENT SYSTEM 8 6 2 Top tray table The top tray table is placed on top of the instrument console and is available for OP deliveries with hanging tube instruments and for the mobile cart The maximum load on the top tray table is 2 kilograms 4 4 Ibs The tray table is attached to the instrument console with a quick connector enabling an easy attachment and detachment of the tray table 8 6 3 Integrated tray table The integrated tray table is available for OP deliveries with hangin
33. al of obsolete units is the responsibility of the waste possessor All parts and components containing hazardous materials must be disposed of in accordance with waste legislation and instructions issued by the environmental authorities The risks involved and the necessary precautions must be taken into account when handling waste products Hazardous Waste Main materials Recyclable e waste 8 disposal for disposal material separate site i collection Frame and covers metal Aluminium galvanised steel plastic PVC PUR other plastics rubber glass porcelain Motor Component boards Cables transformers Amalgam separator filters collectors Packing Wood cardboard paper Other parts Refer to the instructions supplied by the manufacturer User s Manual Planmeca Compact i Classic v2 93 TECHNICAL SPECIFICATIONS 24 TECHNICAL SPECIFICATIONS POWER CONSUMPTION max 1200 VA MAINS VOLTAGE 100 VAC 115 VAC 220 240 VAC MAINS FREQUENCY 50 60 Hz INCOMING AIR PRESSURE 550 kPa to 900 kPa 80 psi to 130 psi INCOMING WATER PRESSURE 300 900 kPa INCOMING WATER HARDNESS lt 8 dH 1 dH 20mg Ca 3I water WEIGHT 130 kg AMBIENT TEMPERATURE Operating 15 C to 35 C 59 F to 95 F Storage 5 C to 60 C 23 F to 140 F RELATIVE HUMIDITY 5 RH to 95 RH absence of condensation ALTITUDE lt 2000 m less than 1 25 miles ELECTRICAL
34. al to the left to activate the Door open assistant call function If the pedal is pushed for longer than 0 5 seconds the function continues for as long as the pedal is pushed The duration of the signal can be programmed see section 17 10 Duration of door open assistant call on page 59 40 Planmeca Compact i Classic v2 User s Manual OPERATING DENTAL UNIT 15 4 Planmeca SingLED operating light NOTE NOTE NOTE Press Operating light to switch the operating light on or off The intensity of the operating light can be programmed see section 17 9 Intensity of operating light on page 58 The intensity can also be adjusted by holding down the Operating light button on the control panel or keeping your hand in front of the infrared light sensor of the operating light for longer than one second After one second the intensity will increase until you release the button switch When you press press and hold the button switch again the intensity will start to decrease The intensity starts to decrease increase after the maximum minimum value has been reached When the limit value is reached you will hear a short signal tone The operating light intensity will decrease slightly when the chair is moving When the polymerisation light is taken from the holder and returned to it within 2 seconds the operating light will dim This feature is configurable contact your Planmeca dealer You can change the o
35. blow to switch the automatic chip blow on or off When the indicator light is lit the automatic chip blow is on and two short blows of water air or both will occur after the micromotor is stopped The type of chip blow can be programmed see section 17 4 Chip blow on page 53 Standard pedal You can temporarily activate the manual chip blow by pushing and holding down the pedal Wide pedal You can temporarily activate the manual chip blow by pushing and holding the pedal to the right The flow of air will continue until you remove your foot from the pedal The type of manual chip blow does not depend on the type of the automatic chip blow but is always dry The manual chip blow can be set to be dependent on programming contact your Planmeca dealer The instrument s fibre optic light is either on or off when you pick up the instrument from the instrument console Whether the light is on or off as well as its intensity can be defined in the programming mode see section 17 6 Fibre optic light LED light on page 55 User s Manual Planmeca Compact i Classic v2 43 OPERATING INSTRUMENTS 16 2 Turbine Speed power NOTE CAUTION Quickstart G Instrument spray Standard pedal To drive the turbine push the foot control pedal to the right or to the left Wide pedal To drive the turbine push the foot control pedal down Pushing the pedal further to the right left or down will increase
36. d holding it for 3 seconds Release the button when you hear a signal tone again The system will first identify the instruments and then each instrument hose is flushed with air and water for 30 seconds in its turn The flushing cycle can be interrupted by pressing any of the instrument buttons After the interruption the dental unit can be used normally Turn the unit off and let the cleaning solution affect in the unit overnight Leave the instruments in the flushing holder overnight User s Manual Planmeca Compact i Classic v2 73 CLEAN WATER SYSTEM 20 2 2 In the morning NOTE OD Open the dental unit door Remove the clean water bottle Rinse the clean water bottle and fill it with clean water Place the clean water bottle back in its place in the dental unit and close the unit door Balanced instrument arms Start the flushing cycle by bending the instrument arms of those instruments that are to be flushed to an angle of at least 90 and simultaneously pressing Instrument spray you will hear a signal tone and holding it for 3 seconds Release the button and arms when you hear a signal tone again Hanging tube instruments Start the flushing cycle by pressing Instrument spray you will hear a signal tone and holding it for 3 seconds Release the button when you hear a signal tone again The system will first identify the instruments and then each instrument hose is flushed w
37. d position using the centre knob on the foot control or the chair buttons on the control panel For more information see section 14 1 Manual operation on page 35 The seat height cannot be programmed near the upper limit The help code HE 08 will appear on the display if the seat position is not allowed When needed the upper limit can be altered Contact your Planmeca dealer Press Program Press the desired chair position button where to store the chair s position rinsing position A B C or D If you want the operating light to be on off in this position turn it on off The chair position appears on the display Press Program to store the chair position into memory User s Manual Planmeca Compact i Classic v2 51 PROGRAMMING 17 3 Instrument spray This procedure does not apply for the scaler For information on how to program the scaler see section 17 5 Scaler on page 54 1 Activate the instrument 2 Press Program 3 Press Instrument spray i The flow of both air and water can be adjusted The St DH UU text SA on the display indicates that the spray air is adjusted and the text SH indicates that the spray water is adjusted The minimum value of all parameters is 0 no flow and maximum 100 marked as F The adjustment step is 1 in the value range 0 25 and 5 in the value range 25 100 4 Adjust the flow rate with the foot control 5
38. desired direction see picture below When the chair reaches the desired position release the centre knob You can steer the chair only in one direction at a time il IO EE Automatic chair positions may be stored into memory See section 17 2 Automatic chair positions on page 51 Press briefly the chair position button where the required position is stored The chair will move automatically to the preprogrammed position To stop the chair from moving either press any of the chair positioning buttons push the foot control pedal in any direction or push the foot control centre knob in any direction 36 Planmeca Compact i Classic v2 User s Manual OPERATING PATIENT CHAIR Backrest d Stop plate Alternatively you can use the foot control to drive the chair to the automatic positions Push the centre knob briefly to the position A B C or D where the preprogrammed chair position is stored The chair will move automatically to the preprogrammed position To stop the chair from moving before it reaches the preprogrammed position push the foot control pedal or the centre knob in any direction The chair movement stops also when the stop plate is pushed or when the backrest is pressed upwards The chair can be driven normally after the possible obstruction has been re
39. e located outside the patient area The dentist assistant and patient must not touch the equipment outside the patient area during treatment CAUTION Use only Planmeca specified devices inside the patient area Inside patient area 1 Dental unit Planmeca monitor Planmeca ProX X ray tube head and arm assembly Planmeca SingLED operating light ao FP eo DN Foot control Outside patient area 6 External PC 7 Planmeca ProX generator assembly User s Manual Planmeca Compact i Classic v2 97 TECHNICAL SPECIFICATIONS Over the patient delivery with balanced instrument arms max 710 28 1 TE 8 ALLE tls strie 1480 58 3 automatic legrest 510 1430 56 3 automatic legrest 460 98 Planmeca Compact i Classic v2 User s Manual TECHNICAL SPECIFICATIONS Over the patient delivery with hanging tube instruments max 710 28 N 1430 56 3 automatic legrest 460 N Jf 6 HAH e 1580 62 2 fixed legrest 610 1480 58 3 automatic legrest 510 User s Manual Planmeca Compact i Classic v2 99 TECHNICAL SPECIFICATIONS 24 3 Planmeca Compact i Classic v2 dental unit s water consumption Part Water consumption Bowl The flow rate is approx 2 5 liters 0 66 gallons per minute The flow rate can be configured Cup filler The cup filling is adjusted for the size of cup you use Syringe The flow rate is approx 0 1 l
40. e oil collector is without removing it completely Pull the oil collector downward from the attachment knob 1 and check the oil level in the narrower chamber 2 If it has started to fill it is time to empty the oil collector Attachment knob To remove the oil collector from the instrument console unscrew the oil collector attachment knob and carefully pull the collector out 78 Planmeca Compact i Classic v2 User s Manual HELP amp ERROR MESSAGES 22 HELP amp ERROR MESSAGES 22 1 Help messages Help messages provide helpful information for the user They are displayed for example if you are using the unit or instrument incorrectly or if the function is not allowed for some reason The following table lists the help messages NOTE In case the unit is not equipped with the Waterline Cleaning System the WCS related help messages can be disabled Contact your Planmeca dealer HELP CODE MEANING ACTION OR EXPLANATION HE1 Amalgam container is 95 full Replace or empty the container as soon as possible or at least before the next patient Pressing the program key allows to continue the operation until the container is 100 totally full HE2 Amalgam container is 100 full Replace or empty the container immediately The suction system cannot be used before the container is emptied or replaced HE3 Patient chair cannot be driven down Check that the space under the sea
41. e upgrade failure E99 1 MCB software upgrade failure E99 2 IMUX software upgrade failure E99 3 Control panel software upgrade failure E99 4 Operating light software upgrade failure E99 5 Motorised headrest software upgrade failure E99 6 Foot control software upgrade failure E99 7 Wireless foot control software upgrade failure E99 8 Wireless foot control receiver software upgrade failure Table 14 Error messages generated by control panel ERROR CODE EXPLANATION EP19 3 Control panel version mismatch EP19 5 Control panel software upgrade has failed or memory card is faulty EP21 1 Control panel display is faulty EP21 2 Control panel data error EP21 5 Unable to read Main PCB software version EP21 6 Control panel software not installed or software error EP21 7 Touch panel is not working Refer to the Planmeca Compact i Classic v2 Technical manual for detailed information on the errors 92 Planmeca Compact i Classic v2 User s Manual UNIT DISPOSAL 23 UNIT DISPOSAL In order to reduce the environmental load over the product s entire lifecycle Planmeca products are designed to be as safe as possible to manufacture use and dispose of Parts which can be recycled should always be taken to the appropriate processing centres after hazardous waste has been removed Dispos
42. ed in the programming mode see section 17 6 Fibre optic light LED light on page 55 User s Manual Planmeca Compact i Classic v2 45 OPERATING INSTRUMENTS 16 3 Scaler NOTE n CAUTION Speed power NOTE CAUTION Instrument spray A scaler requires additional electronics and the scaler type can not be changed without changing electronics Do not use the scaler on patients with cardiac pacemakers The scaler can cause disturbance on the pacemaker s function Standard pedal To drive the scaler push the foot control pedal to the right or to the left Wide pedal To drive the scaler push the foot control pedal down Pushing the pedal further to the right left or down will increase the speed or power of the scaler As you push the pedal the power output will appear on the display To stop the scaler allow the pedal to return to the rest position The speed power level depends on the instrument Ensure that the pedal is in rest position when you activate the scaler Press Instrument spray to turn the instrument spray on or off When the indicator light is lit the spray is on and the water flows when operating the instrument The spray flow rate can be programmed See section 17 5 Scaler on page 54 Alternatively you can turn the instrument spray on off with the foot control Standard pedal Push the pedal down briefly to turn the instrument spray on off Wide pedal Push the pedal b
43. ee section 17 7 Planmeca Lumion polymerisation light on page 56 When the Planmeca Lumion polymerisation light is activated the length of the polymerisation cycle is displayed on the control panel When you start the cycle you will hear a signal tone This signal tone is repeated every 10 seconds and also at 5 seconds The progress of the polymerisation cycle is shown on the display Independent mode The Planmeca Lumion polymerisation light can also be operated in the independent mode marked by d LEd on the control panel The independent mode is typically used when the Planmeca Lumion polymerisation light is attached to the assistant element but the independent mode can also be configured to be used on the dentist side the configuration is performed by a Planmeca service technician When the Planmeca Lumion polymerisation light is in the independent mode it can only be controlled by the buttons on the instrument itself not over the control panel or the foot control To start the polymerisation cycle in the independent mode first select the desired curing mode by pressing the navigation button on the handpiece Then briefly press the start button on the handpiece to start a 10 second exposure or press and hold the start button for 2 seconds to start a 20 second exposure The polymerisation cycle can be interrupted by pressing the start button 48 Planmeca Compact i Classic v2 User s Manual OPERATING INSTRU
44. enings in the flushing holder If you are flushing the smaller round syringe or syringes max 2 remove the instrument cover and use the insert as shown in the figure before placing the syringe s in the flushing holder Lock the syringe s into place with a rotating movement when the syringe s is are in the holder 72 Planmeca Compact i Classic v2 User s Manual CLEAN WATER SYSTEM Syringe The metallic syringe cover must be removed before placing the slightly thicker syringe into the flushing holder Note the orientation of the syringe It does not require an insert and must be placed in the holder as instructed below NOTE NOTE NOTE NOTE NOTE ps clean wu10 e When performing the cleaning operation open the water valves of the instruments This procedure does not clean the instrument handpieces Instrument handpieces are cleaned according to the instrument manufacturer s instructions Clean all water consuming instruments including assistant s syringe Balanced instrument arms Start the flushing cycle by bending the instrument arms of those instruments that are to be flushed to an angle of at least 90 and simultaneously pressing Instrument spray you will hear a signal tone and holding it for 3 seconds Release the button and arms when you hear a signal tone again Hanging tube instruments Start the flushing cycle by Dressing Instrument spray you will hear a signal tone an
45. er s Manual Planmeca Compact i Classic v2 75 MAINTENANCE 21 1 Units with wet suction system BOWL FILTER Empty daily and replace when necessary wW COARSE FILTERS t Empty daily and replace weekly BE 8 KJ oe fr Kal Hl DEPOSIT CUP Check monthly and replace when 70 full 76 Planmeca Compact i Classic v2 User s Manual MAINTENANCE 21 2 Units with Durr VS A separator suction system BOWL FILTER Empty daily and replace when necessary m COARSE FILTERS t Empty daily and replace weekly N 7 d i O i I 151 La 3 f FINE FILTER ee Empty when full Refer to the instructions supplied with the DURR amalgam O separator User s Manual Planmeca Compact i Classic v2 77 MAINTENANCE 21 3 Oil cup 21 3 1 Instrument console with balanced instrument arms The oil collector underneath the instrument console has to be emptied and cleaned monthly Remove the oil cup by turning it counterclockwise as shown in the picture below 21 3 2 Instrument console with hanging tube instruments The oil collector underneath the instrument console has to be checked weekly and emptied when full You can check how full th
46. fication Japanese Radio Law certification symbol To avoid risk of electric shock this equipment must only be connected to a supply mains with protective earth Note that the mains voltage is always present at the mains terminal under the cover when the unit is switched on Do NOT open the cover WARNING The unit contains live mains voltage parts Always first turn off the power to the unit externally before attempting to service the lift motor backrest motor or any parts inside the electronics control box The power supply must be disconnected externally from for example a fuse or a mains switch The fuse or main switch must be lockable into off position Turning off the unit from its own mains switch DOES NOT cut off the mains volt age from all internal nodes User s Manual Planmeca Compact i Classic v2 3 FOR YOUR SAFETY 6 FOR YOUR SAFETY 6 1 Safety precautions NOTE NOTE CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION A A The water used by Planmeca Compact i Touch v2 dental unit instruments and cup fill are to be used for rinsing only The main water tap must be turned off when the dental unit is not in use When the patient is in the chair ensure that the patient s arms and legs are resting on the chair Do not perform other maintenance procedures than those instructed in this manual A faulty or broken dental unit must not be used The denta
47. flushing or use service mode n 101 HE31 Switch unit off leave Planosil in unit for min Turn off the unit if needed When the unit is 8 h Switch unit on Remove container fill it turned back on remove the container fill it with water and attach to unit with water and attach it again to the unit or perform long flushing or use service mode n 101 HE32 Pre rinsing cycle is completed and con Remove the container or perform long flush tainer should be removed ing or use service mode n 101 HE33 Unit is waiting for main water to be turned Open the tap or perform long flushing or use on service mode n 101 User s Manual Planmeca Compact i Classic v2 81 HELP amp ERROR MESSAGES HELP CODE MEANING ACTION OR EXPLANATION HE34 No instr selected when starting instr flush Select remove from holder bend the bal ing or waterline cleaning anced instrument arm at least one instrument and syringe HE35 Instruments are locked for safety reasons Perform long instrument flushing Remove container open tap and press Instr spray key to perform instrument flush ing HE36 After flushing Return instruments to instru ment console HE37 Waterline Cleaning System cycle has been interrupted HE38 Waterline cleaning system help message Low water pressure during final rinsing HE39 Syringe misplaced or flow not detected in The help message wil
48. flushing sde eege geed Ed Ss 65 19 4 Instrument flushing holder dad gege eetegegrdeegeedEN Seege eeedg EE taceduteeeunteciveeeeuendenee 69 19 5 Instrument arms and instrument NOSES A 69 19 6 Instruments coos cecal ctl lac Act eine as red Aae ea 69 19 7 Patient chair upholstery gereest 70 19 87 WITS UM ACES Sei i eE ach ale a a e A a E a ta 70 19 92 Foot One PEE E EAT A utide sende 70 E Le Wel EE 70 20 CLEAN WATER SYSTEM LE 71 201 E elen EE 71 20 2 Waterline cleaning EE 72 21 MAINTENANCE Ge 75 21 1 Units with wet suction system RE 76 21 2 Units with D rr VS A separator suction system rrrnnnrnnnrnnrrrnnnnnnrrnnnnnnnnnnnrrnnrnnrrrnnnn 77 213 Ri KEE 78 22 HELP amp ERROR MESSAGES rrvvvvvvvvvvvvvvvvvvvvvvvnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 79 22 1 Hep Ee EE 79 222 Error messaj sS E 85 23 UNIT DESEN 93 24 TECHNICAL SPECIFICATIONS rrrrvvvvvvvvvvvvnnvnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 94 24 1 Instrument classifications ccccccceesseseceeeececcecaeseeseeeeeeeeecaeseasaseeseeeeeesseseaesssesereseesaeea 95 EE Blann ELE 96 24 3 Planmeca Compact i Classic v2 dental units water consumption aorrrnrnnnrnnnrrnnr 100 ii Planmeca Compact i Classic v2 User s Manual TABLE OF CONTENTS User s Manual Planmeca Compact i Classic v2 iii TABLE OF CONTENTS The manufacturer assembler and importer are responsible for the safety reliability and performance of the unit only if insta
49. g is not activated unless the cup is NOTE Po NOTE Bowl rinsing b 40 Cup filling C75 NOTE positioned in its place under the cup fill tube The water in the dental unit is intended for rinsing only not for drinking Press Program 2 Press Bowl rinse cup fill If you perform the programming from the assistant s control panel press Bowl rinse OR Cup fill depending on what you want to program The letter b on the display indicates that the duration of the bowl rinsing is adjusted The minimum value is 5 sec and the maximum 240 sec and the adjustment step is 5 seconds The letter c on the display indicates that the duration of the cup filling is adjusted The minimum value is 2 seconds and the maximum is 10 seconds The duration is adjusted in steps of 0 5 seconds Adjust the duration with the foot control Change the parameter to be adjusted by pressing Bowl rinse cup fill and adjust its duration with foot control Skip this step if you are performing the programming from the assistant s control panel Press Program The duration of the cup filling can also be programmed as follows Place an empty cup to the cup holder 2 Press Program User s Manual Planmeca Compact i Classic v2 57 PROGRAMMING 17 9 Intensity of operating light NOTE 3 Press Bowl rinse cup fill twice The text c nn n will appear on the display 4 Push the foot contr
50. g tube instruments The maximum load on the tray table is 2 kilograms 4 4 Ibs The integrated tray table is located on the left side of the instrument console 8 6 4 Mouse tray The mouse tray can be attached to the rear of the patient chair or if the assistant s mouse tray is selected to the suction arm post 22 Planmeca Compact i Classic v2 User s Manual SUCTION SYSTEM 9 SUCTION SYSTEM 9 1 Suction arms 9 1 1 Adjustable suction arm The adjustable suction arm is attached to the side of the unit base The adjustable suction arm with assistant s control panel is attached to the side of the unit base Suctonarmeps 9 2 Suction tube holders The suction holder has three openings one for the high power suction tube one for the saliva suction tube and one spare position that can be used either for the assistant s syringe or the assistant s polymerisation light User s Manual Planmeca Compact i Classic v2 23 SUCTION SYSTEM 9 3 Suction handpieces Tilted handpiece Straight handpiece When a saliva or high power suction handpiece is lifted from its holder the suction will automatically start When the handpieces are returned the suction will stop When you are using the suction handpiece the suction can be controlled by sliding the adjuster up or down cattani eps When you lift the suction handpiece from its holder the weight of the suction
51. he risk of operating light induced curing This feature is triggered by picking up and returning the polymerisation light to its holder without starting it The oper ating light returns to normal at the same instance any control is touched or another instrument selected The feature can be dis abled see service mode n 73 in Technical manual chapter Service mode for details HE17 No syringe connected to instrument con sole The console syringe must be re connected otherwise there is an air leak from the syringe QC whenever an instrument or device that requires air pressure is used HE18 No instrument hose connected to this instrument place The instrument is picked up but there is no hose connected at this location Check that all hoses go to the right instrument arms HE19 No syringe connected to connector located on cuspidor The assistant s syringe must be re connected otherwise there is an air leak from the assis tant s syringe QC whenever an instrument or device that requires air pressure is used Install the syringe or disable the syringe using service mode n 84 For details on the service mode see Technical manual chapter Service mode HE20 Connector located on cuspidor allows only syringe other instruments cannot be con nected to this connector The assistant s syringe QC cannot control the currently connected instrument HE21 Flow of both spray air and spray water
52. iters 0 03 gallons per minute Handpieces The flow rate is approx 0 05 liters 0 01 gallons per minute Suction system A small amount of water approx 0 2 liters 0 05 gallons is used to help keep the suction system clean when in use Suction system cleaning Cleaning is done once a day and uses 2 5 liters 0 66 gallons of cycle water 100 Planmeca Compact i Classic v2 User s Manual Planmeca Oy Sorvaajankatu 7 00880 Helsinki Finland tel 358 20 7795 500 fax 358 20 7795 555 sales planmeca com www planmeca com PLANMECA Oys PLANMECA Oys Environmental Quality System tom
53. ith air and water for 30 seconds in its turn The flushing cycle can be interrupted by pressing any of the instrument buttons After the interruption the dental unit can be used normally Repeat the flushing sequence in step 5 at least three times or until the water is clean If the clean water bottle runs out of water refill it You can also use the domestic water mode when performing the flushing Balanced instrument arms Place the instrument hoses back in the instrument arms and the instruments back in the instrument console Hanging tube instruments Place the instruments back in the instrument holders The dental unit is now ready for use 74 Planmeca Compact i Classic v2 User s Manual MAINTENANCE 21 MAINTENANCE CAUTION CAUTION CAUTION When servicing the unit always switch the unit off Note that in extreme conditions the temperature of the chair lift and backrest motors might rise significantly DO NOT TOUCH THE MOTORS Note that the mains voltage is always present at the mains terminal under the Main control PCB cover even if the unit is switched off from its own mains switch The power supply must be disconnected externally from for example a fuse or a mains switch The fuse or main switch must be lockable into off position A ri Int UL Sg tt BE Us
54. l disappear after bend WCS ing the syringe instrument arm and placing the syringe again in the flushing holder HE40 Too many Bien Air MX Brushless Micromo A maximum of two is allowed tors HE41 Insert suction tubes to STCS holder add disinfectant and press green start button upper button HE42 STCS program completed Return suction tubes to unit suction arm and close STCS box cover HE43 STCS program cancelled HE44 Incorrect suction tube amount detected Return them to unit suction arm place them back to STCS holders and start cleaning HE45 Set WMS to Domestic Water Supply mode STCS can not be used when WMS is set to and wait until WMS bottle is full Then start Bottled Water mode STCS cleaning HE46 Suction use is forbidden or there are no The value of service mode n 83 is 0 suction tubes in dental unit configuration HE47 STCS Orotol pressure is low In automa tised STCS Fill Orotol container HE48 WMS must be set to Bottled water off and Bottled water off domestic water is used Bottle on modes before starting STCS Bottle on bottle is used domestic water is cleaning sequence run through the bottle HE50 No cup in cup holder Sensor does not rec Place a cup on the cup holder Or change the ognise cup when pressing cup fill key setting of service mode n 115 HE51 Bowl is above patient chair when driving If the unit has a bowl move the bowl to the chair up rest position If the unit has an OP deli
55. l error messages SE EXPLANATION E1 01 Main water valve short circuit E1 02 Main air valve short circuit E1 03 Bowl rinse valve short circuit E1 04 Cup filling valve short circuit E1 05 Water flush valve short circuit E1 06 Separator pulse valve short circuit E1 07 Ejector valve short circuit E1 08 Extra out 1 short circuit E1 09 Extra out 2 short circuit E1 10 Extra out 3 short circuit E1 11 Separator start signal Microvac s start valve short circuit E1 12 Assistant syringe water valve short circuit E1 13 Separator alarm reset signal short circuit E1 14 PLANET output ELMP short circuit E1 15 Not used or not in the manuals E2 01 Incoming water valve open circuit E2 02 Incoming air valve open circuit E2 03 Bowl rinse valve open circuit E2 04 Cup filling valve open circuit E2 05 Main Control PCB output open circuit warning E2 06 Separator pulse valve open circuit E2 07 Main Control PCB output open circuit warning E2 08 Main Control PCB output open circuit warning E2 09 Main Control PCB output open circuit warning E2 10 Main Control PCB output open circuit warning E2 11 Separator start signal open circuit Microvac valve open circuit E2 12 Assistant syringe water valve open circuit E2 13 Separator alarm reset signal open circuit E2 14 Main Control PCB output open circuit warning E2 15 Not used or not in the
56. l unit must not be used simultane ously with the intraoral X ray unit Planmeca Prox Do not use the scaler on patients with cardiac pacemakers The scaler can cause disturbance on the pacemaker s function Switch off the unit before using an electro surgical knife Electromagnetic interference between the equipment and other devices can occur in very extreme conditions Do not use the equipment in close conjunction with sensi tive devices or devices creating high elec tromagnetic disturbances Do not use the equipment in close conjunc tion with anaesthetic gas or in highly oxy genated environments oxygen content gt 25 WARNING No modification of this dental unit is allowed WARNING Only instruments or equipment approved by Planmeca may be connected to this dental unit 4 Planmeca Compact i Classic v2 User s Manual FOR YOUR SAFETY WARNING The patient must not be in contact with instruments when the patient is resusci tated with a defibrillator WARNING The worm screw securing nut in the chair lift motor must always be attached to the worm screw and must not be removed If the securing nut is faulty or displaced immediately stop using the dental unit and contact a qualified Planmeca service technician Worm screw securing nut IMG_1440 jpg User s Manual Planmeca Compact i Classic v2 5 FOR YOUR SAFETY 6 2 Safety switches Care should be taken when driving the patient
57. llation calibration modification and repairs are carried out by qualified authorized personnel electrical installations are carried out according to the appropriate requirements such as IEC 60364 equipment is used according to the operating instructions Planmeca pursues a policy of continual product development Although every effort is made to produce up to date product documentation this publication should not be re garded as an infallible guide to current specifications We reserve the right to make changes without prior notice COPYRIGHT PLANMECA Publication number 10032684 Revision 1 Released 22 March 2013 iv Planmeca Compact i Classic v2 User s Manual INTRODUCTION 1 INTRODUCTION NOTE NOTE NOTE NOTE NOTE LE Planmeca Compact i Classic v2 dental unit is an electrically controlled dental device that consists of a patient chair cuspidor delivery arm dental instruments and an operating light Planmeca Compact i Classic v2 is meant to be used for dental treatment by dental care professionals This manual describes how to use the Planmeca Compact i Classic v2 dental unit Please read this manual carefully before using the unit The use of Planmeca Compact i Classic v2 dental unit is allowed only under the supervision of dental care professionals The Planmeca Compact i Classic v2 dental unit is compatible with software revision 7 0 or later This manual is valid for software
58. manuals E3 1 Incoming air pressure comp to water pres is too low E3 2 General pressure problem E3 3 General pressure problem E3 4 Internal air pressure after pres regulator is too low User s Manual Planmeca Compact i Classic v2 85 HELP amp ERROR MESSAGES Table 1 General error messages SE EXPLANATION E3 5 Internal air pressure after pres regulator is too high E4 1 Short circuit in cable from MCB to control panel suction holder in branch 1 E4 2 Short circuit in cable from MCB to control panel suction holder in branch 2 E5 Unsupported device attached E6 01 Cuspidor up safety circuit error E6 02 Cuspidor down safety circuit error E6 03 Chair down safety circuit error E6 04 Bowl up safety circuit error E6 05 Bowl down safety circuit error E6 07 Console up safety circuit error E6 08 Console down safety circuit error Table 2 Power supply related error messages SE EXPLANATION E7 IPS voltage failure on MCB E8 Power supply related error messages E9 Internal operating voltage too low E10 Internal operating voltage too high E11 1 OP light fuse F5 and or Water heater fuse F7 has blown on the MCB E11 2 Separator fuse F6 and or Syringe heater fuse F8 has blown on the MCB E11 3 Either of the 24V electronics fuses F9 or F10 has blown on the MCB E11 4 Rectifier
59. moved When the chair has reached its preprogrammed position the position can be adjusted To drive the chair to the required position use the foot control s centre knob or the chair positioning buttons on the touch panel in a non automatic mode The operating light is programmed to switch on or off in preprogrammed positions The light goes off when the chair begins to move to a position where the light has been programmed to be off but goes on only after the chair has reached the programmed position where the light has been programmed to be on For more information on how to program the automatic positions see section 17 2 Automatic chair positions on page 51 User s Manual Planmeca Compact i Classic v2 37 OPERATING PATIENT CHAIR 14 3 Rinsing position NOTE NOTE NOTE NOTE Press Rinsing position to move the chair to the preprogrammed rinsing position The indicator light flashes throughout the movement Filling the cup starts automatically the bowl is rinsed and the operating light goes off The water in the dental unit is intended for rinsing only not for drinking When the chair stops in the rinsing position the indicator light remains on Press Rinsing position a second time to return to the working position The chair remembers this previous position even though it has been moved into the rinsing position Bowl rinsing starts automatically The indicator light flashes throughout the mo
60. nch 1 E49 2 Suction holder PCB or its cable is faulty in branch 2 E50 Unidentified STCS jumper configuration E50 1 WMS must be set to Bottle water off mode when starting STCS cleaning sequence Table 7 Foot control related error messages ERROR CODE EXPLANATION E51 1 Foot control related error messages E51 2 Foot control is not responding E51 3 Foot control pedal was pressed down when dental unit was switched on ERT A Foot control pedal was not in home pos when dental unit was switched on E51 5 Foot ctrl chair ctrl knob was not in home pos when dent unit was switched on E51 6 Foot control left knob is either stuck or active at power up or after pedal use E51 7 Foot control right knob is either stuck or active at power up or after pedal use E52 Foot control is of new type update MCB software E52 1 Incompatible wireless foot control receiver software E52 2 Incompatible wireless foot control software E52 3 Incompatible foot control software E53 Foot control data error cable short circuit E54 0 Foot control error E54 1 Foot control EEPROM write failure E54 2 Foot control EEPROM read failure User s Manual Planmeca Compact i Classic v2 89 HELP amp ERROR MESSAGES Table 7 Foot control related error messages ERROR CODE EXPLANATION
61. ng stops automatically after a preset time Cup filling can be stopped before it stops automatically by pushing the pedal briefly down If the pedal is pushed for longer than 1 second water flows for as long as the pedal is pushed and the bowl is not rinsed The flow rate of the cup fill can be adjusted by turning the black knob inside the unit see section 18 1 Adjusting cup User s Manual Planmeca Compact i Classic v2 39 OPERATING DENTAL UNIT NOTE NOTE 15 3 Door open assistant call NOTE fill and bowl rinse flow rates on page 60 The duration of the cup fill can be programmed see section 17 8 Duration of bowl rinsing and cup filling on page 57 The cup fill is not activated unless the cup is positioned in its place under the cup fill tube The water in the dental unit is intended for rinsing only not for drinking If you have installed a door opening device or assistant call you may activate these from the control panel or the foot control Only one of these functions can be enabled at a time To change the enabled function contact your Planmeca dealer Control panel Press Door open assistant call to activate the function You will hear a short signal tone when the function starts Press Door open assistant call for longer than 0 5 seconds to continue the function until the button is released Foot control When all the instruments are in their holders you can push the ped
62. ning and for covering with protective sleeves and they can also be replaced by the user See section 8 2 Instrument console on page 16 Make sure that the unit is switched off before opening the quick connectors The instrument hoses can not be autoclaved All instruments must be cleaned and serviced according to the information supplied with the instrument After cleaning the instrument let the oil run from it for at least 10 minutes before replacing it on the console Intraoral camera Clean and service the intraoral camera according to the information supplied with the instrument Throw away the disposable hygiene sleeve after use User s Manual Planmeca Compact i Classic v2 69 CLEANING 19 7 Patient chair upholstery Disinfecting 19 8 Unit surfaces NOTE Disinfecting NOTE 19 9 Foot control 19 10 Monitor A mild soap and warm water solution can be used to wipe off stains and spills Air dry or dry quickly with the warm setting of a hair dryer Clean and treat the upholstery weekly with Durr FD 360 We recommend Durr FD 312 or a similar product for disinfecting the upholstery All exposed surfaces should be periodically wiped clean with a non abrasive cleaning agent designed for use with dental units To avoid damage any splashed cleaning solution must be wiped immediately from the surfaces of the dental unit Stronger agents can be used for disinfecting the surfaces of the unit We
63. nitude of the following functions can be programmed e instrument spray automatic chip blow e fibre optic light The instrument spray can be programmed to be on or off when the instrument is picked up from the instrument console Also the type of spray can be programmed For more information see section 17 3 Instrument spray on page 52 The automatic chip blow can be programmed to be on or off when the instrument is picked up from the instrument console Also the type of automatic chip blow can be programmed For more information see section 17 4 Chip blow on page 53 The fibre optic light can be programmed so that it will either be on or off when an instrument is picked up from the instrument console Also the intensity can be adjusted For more information see section 17 6 Fibre optic light LED light on page 55 The fibre optic light can be on only in one instrument at a time for example the fibre optic light of the syringe will switch off if the light of the active instrument is switched on User s Manual Planmeca Compact i Classic v2 19 INSTRUMENT SYSTEM 8 4 4 Reverse rotation of micromotor The direction of the micromotor rotation can be reversed see section 16 1 Micromotor on page 42 8 4 5 Quickstart of air driven instruments 8 5 Instrument logic NOTE The turbine and air motor can be set to start with maximum speed see section 16 2 Turbine on page 44 E
64. nts to be flushed from the instrument arms instrument holders and place the instruments into the openings in the flushing holder If you are flushing the smaller round syringe or syringes max 2 remove the instrument cover and use the insert as shown in the figure before placing the syringe s in the flushing holder Lock the syringe s into place with a rotating movement when the syringe s is are in the holder The metallic syringe cover must be removed before placing the slightly thicker syringe into the flushing holder Note the orientation of the syringe It does not require an insert and must be placed in the holder as instructed below ps clean wu10 e User s Manual Planmeca Compact i Classic v2 65 CLEANING Balanced instrument arms Start the flushing cycle by bending the instrument arms of those instruments including syringe that are to be flushed to an angle of 90 and simultaneously pressing Instrument spray you will hear a signal tone and holding it for 3 seconds Release the button and arms when you hear a second signal tone Hanging tube instruments Start the flushing cycle by pressing nstrument spray you will hear a signal tone and holding it for 3 seconds Release the button when you hear a second signal tone The system will first identify the instruments and then each instrument hose is flushed with air and water for 30 seconds in its turn The flushing cycle can be inter
65. nual OPERATING INSTRUMENTS Momentary spray Automatic chip blow Manual chip blow NOTE Fibre optic light When you are driving the turbine you can activate the momentary spray by pressing the foot control pedal down The spray will continue until you remove your foot from the pedal The momentary spray can be enabled and configured in the service mode contact your Planmeca dealer The momentary spray can not be activated with the wide foot control pedal Press Chip blow to switch the automatic chip blow on or off When the indicator light is lit the automatic chip blow is on and two short blows of water air or both will occur after the turbine is stopped The type of chip blow can be programmed see section 17 4 Chip blow on page 53 Standard pedal You can temporarily activate the manual chip blow by pushing and holding down the pedal Wide pedal You can temporarily activate the manual chip blow by pushing and holding the pedal to the right The flow of air will continue until you remove your foot from the pedal The type of manual chip blow does not depend on the type of the automatic chip blow but is always dry The manual chip blow can be set to be dependent on programming contact your Planmeca dealer The instrument s fibre optic light is either on or off when you pick up the instrument from the instrument console Whether the light is on or off as well as its intensity can be defin
66. ol pedal down The cup filling time will first be set to 2 seconds and will start to increase after pushing the foot control pedal for 2 seconds The pedal can be released and then pushed again and the time continues to increase Continue until the cup is filled to the desired level 5 Press Program 1 Press Program 2 Press Operating light 3 Adjust the intensity of the operating light with the foot control The operating light intensity is shown on the display The minimum value is 70 of the maximum intensity and the maximum 100 and the adjustment step is 2 4 Press Program The light intensity can also be adjusted as described in section 15 4 Planmeca SingLED operating light on page 41 58 Planmeca Compact i Classic v2 User s Manual PROGRAMMING 17 10 Duration of door open assistant call 1 Press Program 2 Press Door open assistant call The door open assistant call time appears on the d 10 display The minimum value is 0 seconds the maximum 250 seconds The value is adjusted in steps of 1 in value range 0 30 and in steps of 5 in value range 30 250 The default value is 5 3 Adjust the door open assistant call time with the foot control 4 Press Program User s Manual Planmeca Compact i Classic v2 59 UNIT ADJUSTMENTS 18 UNIT ADJUSTMENTS 18 1 Adjusting cup fill and bowl rinse flow rates The flow rates of the bowl flush and cup fill can be adjus
67. only The other instruments can be positioned in any order in the four remaining positions The instrument holders can be removed by pulling them out from their openings for example for cleaning The holders are replaced simply by pushing them firmly into their places The angle of the instrument holder can be slightly adjusted User s Manual Planmeca Compact i Classic v2 17 INSTRUMENT SYSTEM 8 3 Quick connector hoses Balanced instrument arms Instrument hose Quick connector Hanging tube instruments NOTE NOTE NOTE Comp HT Inst t QC 170297 NOTE NOTE The instruments are equipped with quick connector hoses to be connected to the instrument console The hose is attached to its place by turning the connector locker clockwise and removed by turning the connector counterclockwise Make sure that the flat part of the connector is upward when attaching the connector to the console Switch the unit off before opening the quick connectors When disconnecting the syringe empty the water and air from the hose before opening the connector The instrument location can be changed simply by removing the instrument with its hose and reconnecting it to the new place The old instrument settings will remain the same despite of the new location of the instrument hose The instrument selection can also be interchanged The settings of the eight last used instruments are stored in the memory
68. orning by pressing Cup fill Bowl rinse 62 Planmeca Compact i Classic v2 User s Manual CLEANING 19 1 5 Cleaning suction handpieces The following explains how the suction handpieces can be disassembled for cleaning High power handpiece Unscrew the handpiece from the suction tube for cleaning If necessary the handpiece can be completely disassembled for more thorough cleaning The handpiece parts can be autoclaved up to 135 C Suction ue SP I Saliva handpiece The saliva handpiece can be disassembled for cleaning by unscrewing the end of the handpiece and removing the core and the adjuster The handpiece parts can be autoclaved up to 135 C Adjuster User s Manual Planmeca Compact i Classic v2 63 CLEANING 19 2 Bowl cleaning NOTE NOTE NOTE Bowl filter parts NOTE Do not pour anything into the bowl unless the unit is switched on and has air and water that is the compressor is switched on and the air and water lines are opened Do not pour anything else than water and a special cleaning agent into the bowl The water must be poured slowly into the bowl The flow may not exceed 5 I min The bowl can be removed and washed in the dishwasher The maximum washing temperature is 65 C At higher temperatures the bowl may break Avoid rapid temperature changes in the dishwasher and when the bowl is in use When positioning the bowl into the dishwasher make sure
69. pedal or the centre knob in any direction or by e pressing the handle of the foot control If the wireless foot control has been idle for 30 minutes default value and has gone to sleep mode you must press the handle twice to stop the chair movements The first press wakes the foot control up from sleep mode and the second press stops the movements User s Manual Planmeca Compact i Classic v2 7 PLANMECA COMPACT i CLASSIC V2 DENTAL UNIT 7 PLANMECA COMPACT i CLASSIC V2 DENTAL UNIT 7 1 Dental unit configurations 7 1 1 Over the patient delivery with balanced instrument arms Monitor Operating light OP delivery arm Balanced instrument arms Cup fill tube Bowl rinse tube Adjustable suction arm with assistant s control panel Cufl3 1 CL prox eps Foot control 8 Planmeca Compact i Classic v2 User s Manual PLANMECA COMPACT i CLASSIC V2 DENTAL UNIT 7 1 2 Over the patient delivery with hanging tube instruments Operating light Monitor ee a Instrument console H with hanging tube HT Me instruments Cup fill tube Control panel Bowl rinse tube Bowl Adjustable suction arm User s Manual Planmeca Compact i Classic v2 9 PLANMECA COMPACT i CLASSIC V2 DENTAL UNIT 7 2 Detachable parts The following detachable components are marked with a manufacturer trademark and model reference Do not
70. peration mode of the light by pressing the on off switch for more than 15 seconds you will hear two signal tones one after 3 and one after 15 seconds 1 The operating light can be switched on off and the brightness can be adjusted from both the light and the dental unit 2 Brightness adjustment can be done only from the operating light The light can be switched on off from both the operating light and the dental unit User s Manual Planmeca Compact i Classic v2 41 OPERATING INSTRUMENTS 16 OPERATING INSTRUMENTS 16 1 Micromotor Speed power NOTE CAUTION Reverse rotation Instrument spray NOTE Standard pedal To drive the micromotor push the foot control pedal to the right or to the left Wide pedal To drive the micromotor push the foot control pedal down Pushing the pedal further to the right left or down will increase the speed or power of the micromotor As you push the pedal the power output will appear on the display The normal range is 10 100 To stop the micromotor allow the pedal to return to the rest position The speed power level depends on the instrument Ensure that the pedal is in rest position when you activate the micromotor In normal operation the micromotor rotates in a clockwise direction To reverse the direction of rotation press Reverse Reversing is possible only when the micromotor is picked up from the instrument console but not operated When the micromotor
71. programming the changes in settings are seen immediately The air water flow of the syringe can not be changed Press Program to activate the programming mode The indicator light is lit Select the desired function from the control panel Change the setting of the function with the foot control To increase the parameter value push the pedal to the right To decrease the parameter value push the pedal to the left When the pedal is pushed halfway right or left the parameter changes slowly When the pedal is pushed to its extreme position right or left the parameter changes quickly If the pedal is pushed more than 0 4 seconds the value will change as long as the pedal is pushed Alternatively you can change the settings with the up down buttons The instrument settings can be adjusted with these buttons without operating the instrument Press Program to store the new setting into memory If you interrupt programming for over 90 seconds the unit automatically exits the programming mode without storing the new settings NOTE To check a function setting without programming it press the Program button and the desired function button The setting is shown on the display Press Program again to close the window without changing the setting 50 Planmeca Compact i Classic v2 User s Manual PROGRAMMING 17 2 Automatic chair positions 1 NOTE EW PoSA 5 Move the chair to the require
72. ram 2 Press Instrument spray The text SH on the display indicates that the spray is adjusted The minimum value is 0 no flow and maximum 100 marked as F 3 Adjust the flow rate with the foot control 4 Press Program 54 Planmeca Compact i Classic v2 User s Manual PROGRAMMING 17 6 Fibre optic light LED light 1 Activate the instrument 2 Press Program 3 Press Reverse 4 Adjust the light intensity with the foot control The minimum value is 70 of the maximum intensity and the maximum 100 and the adjustment step is 2 The light can be programmed to be off after reaching the minimum value the light is switched off indicated by L oFF on the display 5 Press Program The light intensity or the text L oFF appears on the L 90 display User s Manual Planmeca Compact i Classic v2 55 PROGRAMMING 17 7 Planmeca Lumion polymerisation light 1 Press Program 2 Press Reverse NOTE Alternatively you can press Instrument spray or Chip blow 3 Adjust the duration of the polymerisation cycle with the foot control 4 Press Program The remaining time or the text LED appears on the LED display The value range is 5 100 seconds The adjustment step is 5 sec and the default value is 10 sec 56 Planmeca Compact i Classic v2 User s Manual PROGRAMMING 17 8 Duration of bowl rinsing and cup filling NOTE The cup fillin
73. recommend D rr FD 333 FD 322 or a similar disinfecting solution Do not use a spray disinfection solution for the suction arms The foot control surfaces should be periodically wiped clean with a non abrasive cleaning agent designed for use with dental units Clean the monitor according to the instructions given by the manufacturer 70 Planmeca Compact i Classic v2 User s Manual CLEAN WATER SYSTEM 20 CLEAN WATER SYSTEM 20 1 Introduction _ Water Bottle In the Clean Water System CWS the water that is used for the instruments comes from a clean water bottle installed to the dental unit CWS can be used for example when the domestic water is of poor quality the waterline system does not generate enough pressure or if its use is required by legislation The switches on the clean water bottle assembly let you control the water supply clen water bottle eps Pressure monitor 1 Water supply Lets you select the water supply for your dental unit Turn the switch toward CITY to select domestic water and toward BOTTLE to select the clean water bottle 2 Water bottle pressure control The pressure in the water bottle can be adjusted by turning the knob The pressure can be checked from the pressure monitor and should be between 2 5 and 2 8 bar 3 Water bottle When the clean water bottle is used water supply switch turned toward BOTTLE the water bottle switch let
74. revision 7 0 or later In error situations this manual is the primary source of information For information on OEM products please refer to OEM documentation Planmeca Compact i Classic v2 dental unit fulfills the requirements of Directive 93 42 EEC All button illustrations indicate that the button on the display should be pressed Pressing a button will either switch a function on or off depending on the original setting or change the value The display values shown in this manual are only examples and should not be interpreted as recommended values unless otherwise stated 2 ASSOCIATED DOCUMENTATION Planmeca Compact i Classic v2 comes with the following manuals e Users manual For dental care professionals Describes the dental unit and its different parts as well as instructs how to operate and clean the dental unit Installation manual For service personnel Describes how to install the dental unit e Technical manual For service personnel Gives instructions for service situations The intraoral X ray unit Planmeca ProX can be installed to Planmeca Compact i Classic v2 Planmeca ProX is delivered with the following manuals User s Manual Planmeca Compact i Classic v2 1 TRAINING 3 TRAINING e Users manual publication number 10029963 For dental health care professionals Describes the intraoral X ray unit and its different parts as well as instructs how to operate and clean the X ray unit
75. riefly Push pedal to left Activate manual chip blow Push and hold pedal down Push pedal to right Activate momentary spray Push pedal down briefly N A while driving instrument NOTE If you want to change from a standard pedal to the wide pedal or vice versa please contact a qualified Planmeca service technician NOTE The differences in functionality only applies to the operation of some instruments not the operation of the dental unit chair or headrest User s Manual Planmeca Compact i Classic v2 31 FOOT CONTROL NOTE When the functionality of the foot control pedal is different for the standard pedal and the wide pedal this is clearly indicated in the text and picture When the text refers to the foot control pedal in general without making this differentiation the same functionality applies to both types of pedal although the illustration only presents the standard pedal The factory default functions of the foot control when the dental unit is equipped with a normal headrest a standard pedal and no instrument is activated are presented below NOTE The left and right side knobs have no functionality o SS p Chair up long push Backrest down AJ LA SS e de V RB Leste up gt NY chair down Nurse ray I badd badd H ol Cup fill manual When an instrument is activated the functions of the standard pedal depend on the used instrument These instrument specific functions are
76. riefly to the left to turn the instrument spray on off The spray must be switched off when using an instrument without a waterline inside the handpiece The instrument spray operated with the foot control can be disabled in the service mode in which case you can switch the spray on and off only from the control panel Contact your Planmeca dealer 46 Planmeca Compact i Classic v2 User s Manual OPERATING INSTRUMENTS Momentary spray LM scaler EMS No Pain scaler Fibre optic light NOTE NOTE Ko Ka While you are driving the scaler you can temporarily run a momentary spray for example if the spray water flow needs to be increased for a moment The momentary spray is activated by pressing down the foot control pedal The momentary spray can be enabled and configured in the service mode contact your Planmeca dealer The momentary spray can not be activated with the wide foot control pedal The LM scaler has three working modes low 0 40 medium 0 70 and full 0 100 When the scaler is the active instrument the working mode can be changed by pressing Chip blow The EMS No Pain scaler has three operation modes the abbreviation in the brackets is displayed on the control panel endodontics Endo power range 1 50 scaling SCAL power range 1 100 and restoration rES power range 50 100 The power range for all three operation modes is displayed as 1 100 for example in the
77. rupted by pressing any of the instrument buttons After the interruption the dental unit can be used normally Once the flushing cycle is finished remove the instruments and place the holder cover to its position When HE 36 is displayed after the flushing cycle remove the console syringe from the flushing holder and return it to the instrument holder Balanced instrument arms 1 If the balanced arm is bent and syringe hose is in the balanced arm remove the syringe from the flushing holder and return it to the instrument holder balanced arm straightens up and syringe becomes deactivated 2 If the syringe has been removed from the flushing holder and is in the instrument holder but the hose is removed from the instrument arm attach the hose to the arm pick up the syringe and return it to the instrument holder This ensures that no water will flow from the syringes after flushing Hanging tube instruments If the syringe is already removed from the flushing holder return it to the instrument holder 66 Planmeca Compact i Classic v2 User s Manual CLEANING 19 3 2 Long flushing after working day NOTE We recommend that long flushing be performed in the morning and after the working day NOTE The instrument hoses can be flushed independently or at the same time as the suction system is being cleaned 1 Remove the cup from the cup holder Turn the bowl away from above the flushing holder as shown in
78. s Bowl rinse briefly once to rinse the bowl The bowl rinsing can be stopped before it stops automatically by pressing the button twice The flow rate of the bowl rinse can be adjusted by turning the black knob inside the unit see section 18 1 Adjusting cup fill and bowl rinse flow rates on page 60 The duration of bowl rinsing can be programmed see section 17 8 Duration of bowl rinsing and cup filling on page 57 Dentist s control panel Press Bowl rinse cup fill twice or press the button once until the cup filling starts 0 5 1 sec and the unit will automatically fill the cup and then rinse the bowl Cup filling can be stopped before it stops automatically by pressing the button briefly If the button is pressed for longer than 1 second water flows for as long as the button is pressed and the bowl is not rinsed Assistant s control panel Press Cup fill briefly and the unit will automatically fill the cup and then rinse the bowl Cup filling can be stopped before it stops automatically by pressing the button briefly If the button is pressed for longer than 1 second water flows for as long as the button is pressed and the bowl is not rinsed Foot control When all the instruments are in their holders you can fill the cup either by pushing the pedal down twice or by pushing the pedal down once until the filling starts 0 5 1 sec The unit will automatically fill the cup and then rinse the bowl Cup filli
79. s auto backrest If this help message is shown while matic positions are not switched on the patient chair is attached to the unit it means that you have forgotten to switch on the chairs automatic positions To clear the mes sage put the operation mode switch on the cuspidor side of the chair base in the AUTO position switch up HE27 Drive backrest upwards then lower seat If Drive the backrest upwards before lowering patient chair is attached to unit chair s auto the seat If this help message is shown while matic positions are not switched on the patient chair is attached to the unit it means that you have forgotten to switch on the chairs automatic positions To clear the mes sage put the operation mode switch on the cuspidor side of the chair base in the AUTO position switch up HE28 Planmeca Compact WE s help message Connect the lifter cable HE29 Drive seat downwards then lower backrest Drive the seat downwards before lowering the If patient chair is attached to unit chair s backrest If this help message is shown while automatic positions are not switched on the patient chair is attached to the unit it means that you have forgotten to switch on the chairs automatic positions To clear the mes sage put the operation mode switch on the cuspidor side of the chair base in the AUTO position switch up HE30 Unit is waiting for container to be attached Attach the container or perform long
80. s not run or no signal from position potentiometer E65 1 Lift motor does not run EmeStop relay PCB cables or position sensor cable may be faulty E66 Lift motor or its position potentiometer cable has a wrong connection E67 Backrest position potentiometer or its cable is faulty or disconnected E68 Backrest motor does not run or no signal from position potentiometer 90 Planmeca Compact i Classic v2 User s Manual HELP amp ERROR MESSAGES Table 10 Patient chair related error messages SE EXPLANATION E68 1 Backrest motor does not run EmeStop relay PCB cables or position sensor cable may be faulty E69 Backrest motor or its position potentiometer cable has a wrong connection E70 E70 1 Lift motor error E70 2 Backrest motor error E71 Patient chair related Table 11 MAIN CPU related error messages pois EXPLANATION E72 1 Program Flash EPROM error Main software is corrupted Replace Flash EPROM E72 2 Program Flash EPROM error Boot software is corrupted Replace Flash EPROM E72 3 Program Flash EPROM error E72 4 Data transfer error while updating main PCB SW from control panel memory device E73 1 EEPROM error CPU EEPROM erase program failure replace CPU E73 2 CPU configuration register contents are wrong replace CPU E73 3 CPU EEPROM checksum
81. s you turn the bottle on or off When the switch is toward ON the pressure is maintained in the bottle and the bottle can be used User s Manual Planmeca Compact i Classic v2 71 CLEAN WATER SYSTEM 20 2 Waterline cleaning When the switch is toward OFF you can detach the bottle for example for cleaning Allow a few seconds for the pressure to drop before unscrewing the bottle CAUTION Only Planmeca Planosil cleaning solution must be used Planmeca does not guarantee the suitability of and is not liable for damages caused by other cleaning solutions To avoid stains possible cleaning solution splashes should be wiped away immediately NOTE 20 2 1 After the working day NOTE Insert for syringe RON Open the dental unit door Remove the clean water bottle Empty the possible water from the clean water bottle Fill the clean water bottle with approx 1 dl of cleaning solution The amount depends on the unit configuration We recommend you keep record of how much solution has been used Place the clean water bottle back in its place in the dental unit and close the unit door Ensure that the water supply switch is turned toward BOTTLE and that the water bottle switch is turned toward ON Remove the hoses of all water consuming instruments including syringe from the instrument arms instrument holders and place the instruments and syringes into the op
82. specially in four handed dentistry it is important to enable smooth cleaning and exchange of instruments between the dentist and the assistant The Planmeca Compact i Classic v2 dental unit contains an instrument logic with the principles described below The active instrument can be operated with the foot control and its settings are shown on the control panel and they can be changed 1 The last instrument picked up from the instrument console can be driven with the foot control a short push to the right left or down is enough 2 After activating one instrument the others can be picked up from the console without changing the active instrument 3 Only after the active instrument has been returned to the console another instrument can be activated by picking it up from the instrument console After this it can be driven with the foot control as above Other instruments can be away from the console but they can not be driven 4 The memory operation of the logic settings makes it possible to store parameters and settings for up to eight instruments Changing the place of the instrument on the console does not change the parameters and settings of that instrument 5 The instrument logic does not control the syringe which can be used at any time If you use similar instruments at the same time keep them in their own places The memory operation does not recognise the parameters and settings of the similar instruments if their pl
83. splays the current operation status of the instrument During programming the indicator light on the instrument button indicates whether the function is selected to the active instrument The indicator light on the Rinsing position button shows when the chair is in the rinsing position The indicator light on the Program button shows when the unit is in the programming mode In case of malfunction an error code or a help message is shown on the display see section 22 HELP amp ERROR MESSAGES on page 79 User s Manual Planmeca Compact i Classic v2 29 CONTROL PANEL Display Speed power P 80 Curing time 0 HE 02 A N E oO The display shows information related to the current operation and changes accordingly In normal operation the speed or power of the active instrument is shown on the display percentage of the maximum value If the polymerisation light is the active instrument the display shows the current curing time In the programming mode the setting to be changed is shown on the display see section 17 PROGRAMMING on page 50 In case of malfunction an error code or a help message is shown on the display see section 22 HELP amp ERROR MESSAGES on page 79 11 2 Optional assistant s control panel In addition to the dentist s control panel a control panel for the assistant is available as an option Both panels can be used for controlling and programming the instruments
84. syringes after flushing Hanging tube instruments If the syringe is already removed from the flushing holder return it to the instrument holder NOTE After the flushing cycle the unit should immediately be switched off This procedure ensures that cool water remains in the pipelines of the unit thus NOTE minimising the growth of biofilm The duration of the long flushing cycle is configurable Contact your Planmeca dealer 68 Planmeca Compact i Classic v2 User s Manual CLEANING NOTE 19 4 Instrument flushing holder Instrument HELP MESSAGE HE 99 The dental unit can be configured to display help message HE 99 if the unit has been switched off without performing long flushing after water has been used When HE 99 has been enabled in the service mode it can be displayed as a reminder only or it can be set to disappear only after you have performed long flushing To change service mode settings please contact your Planmeca dealer The instrument flushing holder can be lifted away from its position It can be autoclaved up to 135 C Note that the flushing holder cover can not be autoclaved Remove the cover before autoclaving the instrument flushing holder 19 5 Instrument arms and instrument hoses 19 6 Instruments NOTE NOTE NOTE The instrument arms can be removed from the console They can be cleaned with a non abrasive cleaning agent The instrument hoses can be removed for clea
85. t is free because safety switch is activated and nothing is touching the plate at the bot tom The chair can be driven normally after the possible obstruction has been removed HE4 This left hand instrument position allows The leftmost position in the console is only syringe reserved for the syringe only Replace this instrument with a syringe Place the other instrument to one of the four right hand places HE5 This instrument position does not accept Remove the syringe from this position and syringe replace it with any other kind of instrument The syringe must be placed in the leftmost place HE6 Patient chair cannot be driven when instru Stop the instrument release the foot con ment is in use trol pedal to be able to run the chair HE7 Patient chair up down movement is not Close the cuspidor door to be able to run the allowed when cuspidor door is open chair up down or to a pre programmed posi tion HE8 Seat height can not be programmed this Run the chair slightly down to be able to pro high in automatic positions for patient safety gram this position into memory reasons HE9 This scaler cannot currently be used with This scaler needs a dedicated electronics that this unit is not installed or the scaler electronics installed is not compatible with this scaler HE10 Wait while configuring the dental instrument Wait a few seconds for the unit to check your setup instrument configuration since it has changed
86. ted Check that nothing is blocking the headrest when driving headrest Check that nothing movement The headrest can be driven nor is blocking headrest movements mally after the possible obstruction has been removed HE83 Foot control emergency switch is active HE85 SW update denied Chair was moving or The chair was moving or an instrument was in instrument was in use while starting SW use while starting the software update update HE86 SW update denied Incorrect control panel An incorrect control panel type was detected type was detected while starting SW while starting the software update update HE90 This key has no function at the moment press Pos Sel Chair Headr Light Sel first HE91 Stop Help button pressed HE92 Help Stop button pressed HE93 This key has no function at the moment because there is no motorised light HE95 Patient chair automatic position cannot be reached because legrest is unlocked or armrests are blocking movement HE99 Unit has been switched off without perform This help message can be disabled see Tech ing long flushing after water has been used nical manual service mode n 99 for details Perform long flushing HE200 Detected new software update Confirm to install HE201 Detected new software update SD card Confirm to install 5 3 0 9 R User s Manual Planmeca Compact i Classic v2 83 HELP amp ERROR MESSAGES
87. ted error messages E18 Power Supply related error messages Table 3 Control panel related error messages SE EXPLANATION E19 1 Control panel in branch 1 is of new type E19 2 Control panel in branch 2 is of new type E20 1 Control panel 1 key stuck E20 2 Control panel 2 key stuck E21 Control panel related error messages E22 Control panel related error messages Table 4 Instrument related error messages SA EXPLANATION E23 Polymerisation light bulb has blown or is not properly attached to socket E24 Control panel related error messages E25 Satelec mini LED polymerisation light requires newer IMUX PCB version E26 Instrument related error messages E27 Instrument related error messages Table 5 Instrument multiplexer related error messages Se EXPLANATION E28 1 Reference resistor signal out of bounds when unit is switched on E28 2 Active instrument signal out of bounds E28 3 Syringe signal out of bounds E28 4 Reference resistor signal out of bounds when instrument is activated E28 5 Syringe signal changes during use blinking E29 Voltage error in fibre light power supply in IMUX E30 Instrument multiplexer related error messages E31 Instrument multiplexer related error messages E32 1 IMUX is not responding IMUX cable disconnected or failure in cable or IMUX User s Manual Planmeca Compact i Classic v2 87 HELP amp ERROR MESSAGES Table 5 Instrument multiplexer related error messages
88. ted with the two black knobs located inside the dental unit Cup fill Bowl rinse TR L FE BR o oO NOTE Check also the duration of the cup fill when adjusting its flow rate See section 17 8 Duration of bowl rinsing and cup filling on page 57 60 Planmeca Compact i Classic v2 User s Manual CLEANING 19 CLEANING NOTE Before starting the cleaning procedures in the evening hang the foot control on the hook under the patient chair IMG 7571 jpg 19 1 Suction system 19 1 1 In the morning 1 Rinse the suction tubes with 1 litre of water by aspirating water and air through the suction handpieces 2 Wipe the suction handpieces with Durr FD 333 FD 322 19 1 2 After each patient 1 Remove the used aspirating tips 2 For hygienic and operational reasons empty one glass of water 100 200 ml with each suction tube by aspirating water and air through the suction handpiece Do this even if only the saliva suction tube has been used 3 Clean the suction handpieces and wipe them with D rr FD 333 FD 322 or autoclave them 4 Wash or disinfect the suction holders with Durr FD 333 FD 322 User s Manual Planmeca
89. that the bowl does not press other objects in the machine Clean the bowl after every patient by pouring a few drops of the cleaning solution into the bowl and using a soft brush Rinse the bowl by pressing Cup fill Bowl rinse The outside of the bowl can be wiped clean with a damp cloth The bowl can also be removed and washed in the dishwasher if required Remove the bowl filter parts 1 push the bowl fastening clip carefully down 2 and rotate the bowl counterclockwise and slightly upward 3 You can now remove the bowl by pulling it horizontally away from the cuspidor 4 Replace the bowl in reverse order The cover cap of the filter makes the removal of the filter easier but the filter can also be used without the cover cap 64 Planmeca Compact i Classic v2 User s Manual CLEANING 19 3 Instrument hose flushing 19 3 1 Short instrument hose flushing during working day Flushing holder cover for syringe Syringe NOTE Werecommend that short instrument hose flushing be performed after each patient The instrument hoses can be flushed independently or at the same time as the suction system is being cleaned Remove the cup from the cup holder Turn the bowl away from above the flushing holder as shown in the figure Turn also the cup fill tube above the bowl as shown in the figure Press the outer edge of the flushing holder cover and remove the cover Remove the hoses of the instrume
90. the speed or power of the turbine As you push the pedal the power output will appear on the display The normal range is 5 100 To stop the turbine allow the pedal to return to the rest position The speed power level depends on the instrument Ensure that the pedal is in rest position when you activate the turbine The turbine air motor will start with maximum speed if the quickstart is enabled When the instrument is active but not operated press Reverse to enable disable the quickstart When quickstart is enabled the indicator light is on Press the Instrument spray to turn the instrument cooling spray on or off When the indicator light is lit the spray is on and the spray of water air or both of them are flowing when operating the instrument The spray flow rate can be programmed See section 17 3 Instrument spray on page 52 Alternatively you can turn the instrument spray on off with the foot control Standard pedal Push the pedal down briefly to turn the instrument spray on off Wide pedal Push the pedal briefly to the left to turn the instrument spray on off The spray must be switched off when using an instrument without a waterline inside the handpiece The instrument spray operated with the foot control can be disabled in the service mode in which case you can switch the spray on and off only from the control panel Contact your Planmeca dealer 44 Planmeca Compact i Classic v2 User s Ma
91. vement When the chair stops the operating light turns back on if it was on initially If you press and hold the Rinsing position button when moving the chair to the rinsing position you will enter the position normally but when the chair stops in the rinsing position the indicator light goes off and the chair does not remember its previous position If you press and hold the Rinsing position button when the chair is in the rinsing position the indicator light goes off and the chair will forget the previous position the return function is inactivated The unit can be set up so that the indicator light on the Rinsing position button goes off and the previous position is forgotten when you are driving from the rinsing position to a preprogrammed position Next time you press Rinsing position the chair will move to the rinsing position Contact your Planmeca dealer Alternatively you can drive the chair to the rinsing position by pushing the pedal to the far right and down For information on how to program the rinsing position see section 17 2 Automatic chair positions on page 51 38 Planmeca Compact i Classic v2 User s Manual OPERATING DENTAL UNIT 15 OPERATING DENTAL UNIT 15 1 Bowlrinse 15 2 Cup fill Dentist s control panel Press Bowl rinse cup fill to rinse the bowl Bowl rinsing can be stopped before it stops automatically by pressing the button again Assistant s control panel Pres
92. very arm safety switch check that the OP delivery arm is not blocking the chair movement HE52 Patient chair can not be driven upward because safety switch of side delivery arm is released 82 Planmeca Compact i Classic v2 User s Manual HELP amp ERROR MESSAGES HELP CODE MEANING ACTION OR EXPLANATION HE53 Patient chair can not be driven downward because safety switch of side delivery arm is released HE54 Cup is inserted in cup holder Remove the cup and make sure the cup fill tube is above the bowl HE60 WMS Container almost empty in Domestic Reduce water use for a moment water supply mode HE61 WMS Container almost empty in Bottled Reduce water use and fill the container as water mode soon as possible HE62 WMS Container switch is turned off Switch on the container switch HE63 Cuspidor door is open Close the door HE64 Fill container with disinfectant over upper sensor HE65 Fill container with water over upper sensor HE66 Wait 8 hours or switch unit off for the night HE70 Brushless micromotor is stuck or broken HE80 Headrest length safety feature activated Check that nothing is blocking the headrest when driving headrest Check that nothing movement The headrest can be driven nor is blocking headrest movements mally after the possible obstruction has been removed HE81 Headrest angle safety feature activa
93. y pressing Instrument spray you will hear a signal tone and holding it for 6 seconds Release the button when you have heard a second and a third signal tone The system will first identify the instruments and then each instrument hose is flushed with air and water in its turn The time of flushing is the same for all instruments The total flushing time is shown on the display At the same time the cup fill tube and the bowl are flushed too Adjust the water flow of the cup fill tube so that the water does not splash into the bowl The flushing cycle can be interrupted by pressing any of the instrument buttons After the interruption the dental unit can be used normally Once the flushing cycle is finished remove the instruments and place the holder cover to its position When HE 36 is displayed after the flushing cycle remove the console syringe from the flushing holder and return it to the instrument holder Balanced instrument arms 1 If the balanced arm is bent and syringe hose is in the balanced arm remove the syringe from the flushing holder and return it to the instrument holder balanced arm straightens up and syringe becomes deactivated 2 If the syringe has been removed from the flushing holder and is in the instrument holder but the hose is removed from the instrument arm attach the hose to the arm pick up the syringe and return it to the instrument holder This ensures that no water will flow from the

user's manual - Eki'p Dental

Contents

Download Pdf Manuals

Related Search

Related Contents