User's Manual
Contents
1. User s Manual Thank you for choosing our product please carefully read this manual and operate it obey the specification in order to make sure you can correct and safety installing operating and maintaining it We will not take any responsibility for the damage and body injury which caused by the abnormal operation A1 This Manual includes the important information of installation and operation Please install and operate the light according to the instructions strictly And it must be power off when open the light or before repair and replace the lamp A Please read the complete contents of this manual please keep this manual attach with the light for any preview B In order to make sure the correct and safety installation operation and maintenance well know and follow to the instructions of Manual is necessary C We will not take any responsibility to the light damage property loss or body injure which caused by the incorrect installation operation and maintenance NOTICE The data which inside the Manual maybe changed due to the continuous improvement and we ll not make another notice We will keep the right to any specification update during improvement Warning If the protection screen lens or UV screen gota visible damage eg scratch or chasm Packing Contents accessories Selectable 1 Power Cable 1PCS a Bracket 2 Signal Cable 1PCS b Clamp 3 User s Manual 1PCS c Safety Cable MUnpack2. be adjustment 188 204 White shade CH6 change speed 222 238 RGB Swatchange 239 255 RGB shade CO Ro ee aim 40 59 Auto running mode2 60 79 Auto running mode3 80 99 Auto running mode4 100 119 Auto running mode5 120 139 jAuto running mode6 140 159 Sound model R G B whitelstrobe Sound control 160 179 Sound mode2 R strobe 180 199 Sound mode3 G strobe 200 219 Sound mode4 B strobe 220 239 Sound moded 240 255 Sound mode6 seven color jump Clean and use frequency To confirm the power supply have cut off before disconnect the light or repair it it is very important to keep the light cleaning Not only can keep the light maximum brightness output but also can prolong their use life Please use the high quality orofessional glass and soft cloth to clear up the equipment not permission to use the alcohol and organic liquid clean at least once each year use vacuum dust collector When the light does not start check whether the light power supply fuse blown or not if blow install the appropriate fuse and start the light after find out troubleshooting but please attention to the technically person allowed to carry out maintenance work Products returned if it is the products quality problem the customer can be based on the actual situation to decide whether need the product parts to replace Complain 1 The salesman will check the details of
3. is 1 5 46 analogously Auto mode Dial the code 10 and 8 to ON the device will be in auto running mode The dial codes 1 2 and 3 are the conversion of the different modes of auto running Following the list te LUM n Remark Auto running show include shade strobe change color and so on a Function descripti 10 8 Auto 10 8 1 10 8 2 Gshade FCS 10 8 3 Bshade S 10 84 2 1 RGB shade speed 1 fast 10 8 3 1 RGBshade speed2 sd RGB shade 10 84 3 2 speed3slow 10 8 3 2 1 R G Bshade Cid Sound control mode Dial the code 10 and 7 to ON the device will be in sound control mode The dial code 1 2 3 4 and 5 are the conversion of the different modes of sound control mode DIP number 1047 Sound modal Com 2d SSS 101742 s O O SSS S Toms 4 SC dCOSSSSS Setting master machine is when dial the code 10 to ON control the slave machine can by DMX connect interface All dial code to OFF when dial 10 to OFF 1 to 9is the light address code setting 8421 binary code format are all OFF the address is 001 Master slave mode Setup master machine and dial code 10 to ON cancontrol slave machine by DMX connect interface All dial code to OFF when slave machine receiving 1 9 is the light address code setup 8421 Binary encoding format when dial 10 to OFF the address code is 001 when all OFF Warm Tip The light auto running effect are selected from the control ch
4. al big hook link the hanging screw hole on the bottom of the light must be ensure that the light will not fell down from support rack through the support rack and light hand use the safety rope for auxiliary lifting handle to ensure safety to prevent the light falling and sliding Whether there is wear and tear whether there is loose hook The manufacturer does not take any responsibility if the light falling because hanging installation is not stable Warning 1 Hook use only for light lifting 2 Hook as a handle move the light to prohibit carrying please use the handle DMxX Address Code Setting Every light should be set with DMX address code when you are using the controller to control multi lights itis used to receive the signal from the controller Since the product uses address code dial code set the address code so each dial code corresponding to address values are as follows Corresponding to address code value The present address code of the light address code of last light channel quantity of the light The light with 9 Channels so it should be under the 16channel control mode the DMX address code of the first light is 1 the corresponding dial code is 1 or all of the dial code not dial the second should be 1 16 17 the corresponding dial code is 1 5 the third light address value is 1 16 2 33 the corresponding dial code is 1 6 The fourth should be 1 16 3 49 the corresponding dial code
5. annel with the proceeds so users can use the DMX controller of have storage capabilities to make out the changers effect of your need Ro Cos dB Fixed color away brightness Auto running show include shade strobe change color and so on ai P R shade shade B shade RGB shade speed 1 fast RGB shade speed 2 RGB shade speed 3 slow R G B shade RGB change each other R strobe G strobe 5 strobe R B strobe R G strobe Strobe G B strobe 10 9 2 1 R G B strobe speed p P3 DIP7 adjustment strobe speed adjustment Sound control orna Sound contro i SS 10 7 2_ Soundcontrols SSS o3 lSoundcontroa dS shade 10 7 4 Sound control 10 7 5 Sound control6 ATE U E PE l Usage of the Signal Cable Connector The connection between the output and input it s available to use the 3 pins XLR cable which provided by the manufacturer Signal cable from the DMX output of the controller to the input of the first master light and connect to the DMX input of second slave light from the DMX output of the first master light analogously till connected all the slave lights and insert the last connector to the output of the final light If you want to prolong the connection of signal cable the connection of the pins between male connector and female connector should be 1 to 1 2 to 2 3 to 3 or it will cause Communication interruption Notice the diameter
6. complained problem included the item no delivered quantity delivery time faulty and pictures and the requirement of customer 2 The customer service technicians to analyze and contact with customers by phone to guide customer 3 Quality Technology Department analysis of customer complaints and give a preliminary identified The units must be offer analysis and treatment measures on time i A 1 Check if the fuse is burnt out 2 Check if the power is correctly connected 1 Check if the DMX address code is correctly set 2 Check the signal communication of the wires 1 Check if the lamp is over the work life 2 Check if the internal optic system is clear Clean the dust or grease of the lamp lens and other parts 1 Check if the lens is broken 2 Clean the dust of grease of the lens 1 Check if the lamp is over the work life Replace the lamp if it Is Light doesn t work Light is working but not controllable by controller The light beam is dark and with visible reduction Beam is imperfect with halo Beam with serious distortion Lamp doesn t work fs T
7. ing Instruction Please check if all the contents are completed after unpacking then check if the light is undamaged Please you can keep the original package and return to the factory if it s damaged WAC Power Check if the voltage is accordance with the rated power WSafety Specifications all the safety items of operation includes installation and before operating 1 Unpacking the carton and take out all the accessories and open the poly package take out the light from the flight case and put it in a certain platform for operation 2 This device for indoor use only the protection grade is IP20 the light must keep dry and avoid to use under the Moist Overheat or Dusty surroundings And keep the light far away from the water or other liquid 3 Installing of the light must keep a distance with any flammable objects by 5m at least The distance between the light and the projected objects mustbe noless than 1m 4 Please never install the light on the surface of the flammable objects 5 The installation operation and maintenance must be managed by the qualified professional and make sure to operate it under the instruction of the Manual 6 Make sure the work environment temperature of the light maximum 45 C and minimum 20 C 7 The temperature of the light surface will up to 130 C even under the normal cooling so never touch it by hand 8 The light was designed as electric shock protection type and must connect to the power su
8. lamp First after unscrewed the screw at the head of shell and then pull out it Youcan see the LED If found the LED are not bright then replace them Installation method is just the opposite Warning 1 The light power supply must be disconnected when replacement of the LED does not bright 2 you can repair the light before you must use a thermostat with anti static electric iron and wear anti static rings Power supply wire Connection Using a dedicated plug to connect the device and power The devicemini mushroom should pay attention to whether the voltage and frequency between signs and on the power supply are the same or not Suggested that each light has a separate power supply switch this can be turned on or off at random for each device The device selection of input voltage and frequency parameters as follows AC220V 240V AC110V 240V Frequency 60hz Lo 2 yin If the power cable is damaged please contact the area agents or ask professional to replace please use the same specification cable when you replace the power cable Tip When connecting the power ground wire must yellow green color wire safety grounding electrical installation must comply with all relevant standards Fixed installation of lighting including light hook and safety rope how to use Before positioned the light ensure the stability of the installation site In the reverse hanging installation use two sets of M10 bolts with a profession
9. of core of every cable should be 0 5mm at least double core shelter cable should be used The signal connecting must use the attached 3 pins XLR cable Notice all the internal lead wire of the 3 pins XLR cable should not touch to each other or connect to the connector The light is available to receive the DMX512 signal connect the signal plug to the panel which marked with IN and connect it to the next light then connect to the In of next light from the OUT The DMX signal terminal organ is recommended when the lighting signal is connecting It will avoid to damage the signal which caused by the noise DMX terminal organ is a XLR connector connect with a 120Q resistor between the pin 2 and pin 3 of the XLR connector and connect it to the last OUTPUT socket of the final light Follow picture AIT 7 N IN OUT ee 5 m 5 Q Q Q Q 6 Q Q gt gt gt at m s r D 3 120R 1W DMX channel value list After completion all operations press the power switch check if everything is normal Channel Function value Description position adjust position by Ch2 Rotate come and back adjust range 16255 speed position fasts low CH3 dimmer strobe 8 232 strobe slow fast On off 233 255 on Adust the value Obtana stronger sense of visualimpact 0 17 none CH6 CH7 CH8 dimmer 35 51 Red sd 69 85 86 102 Yellow 103 119 Magenta CH5 Fixedcolor shade shading can
10. pply system which well earthed Furthermore the ground wire of the light must connect to the ground wire of the power supply system ground A xo wire interface of the light must well connect with the light body or light must well earthed 9 Please check if the voltage is accordance with the rated power before installing 10 Please never use the power cabie which was damaged the insulation cover meanwhile never put the power cable on any other wire Please pull out the power cable by handle the plug when light is stop working or cleaning never pull out it roughly or handle the wire directly 11 The light doesn t include any spare parts for repair please check if all the parts are well installed and screws are drove tightly before operating It s prohibited to use the light when the cover is opened Notice Please make sure it s power off before any installation repair and clean Introduction MTechnical Features 1 Control channel 9 DMX channels 2 Color RGB three basic color color shade 3 Operating modes standard DMX512 controller control mode 4 Other function rotate angle 180 master and slave mode sound control 5 Appearance metal shell streamlined designs 6 Working environment indoor 20 C 40 C 7 1P degree IP20 nology Parameter Voltage AC220 240V 50Hz 110V 120V 60Hz can be select Power 35W Fuse F1A 250VAC LED lamp 3X3W R f Gt BI PWN gt 1 Install replace LED
Download Pdf Manuals
Related Search