Home

TDP-245/ TDP-245 Plus/ TDP-247/ TDP

image

Contents

1. cover from the lower cover Lower inner cover Lower cover 7 Thread the harness red connector through the cable hole at the front side of lower inner cover Plug the red peel off module harness connector at the location JP17 TDP 245 JP19 TDP 245 Plus TDP 247 TDP 345 on the main board Place lower inner cover to the lower cover Install the peel off module to the lower inner cover slot A Peel off module assembly Install one side first and install another side 8 Gently push peel off panel to lock to the lower inner cover 9 Reassemble parts in reverse procedures after installing the module 11 3 4 Loading Label for Peel off Mode Option 1 Open the peel off module by pulling it out Peel off Roller Peel off Panel 2 Thread the label printing side facing up through the label guides and place it on top of the platen 3 Thread the label through the liner opening which is beneath the roller 4 Adjust the black center biased label guides by turning adjustment knob to fit the edge of the label backing Adjustment Knob Roller Peel off panel 5 Push the peel off panel back to the printer 6 Close the top cover 12 13 3 5 External Label Roll Mount Installation Option 1 Attach an external label roll mount on the bottom of the printer 2 Install a roll of label on the external label roll mount Label External Label Roll Mount 3 Feed the
2. Peel off module assembly B Guillotine cutter Full cut Paper thickness 0 06 0 19mm 500 000 cuts Partial cut Paper thickness 0 06 0 12mm 500 000 cuts Paper thickness 0 19mm 200 000 cuts B Main board integrated with internal Ethernet B Internal Ethernet print server module User option B 200 B KU 00 plus B External Ethernet print server B External wireless 802 110 0 print server B External roll mount media OD 214 mm 8 4 with core label spindle B Contact CCD contact scanner B Long range linear image bar code scanner 2 3 Printer Parts 2 3 1 Front View Clear Window Top Cover LED Indicator Feed Button Label Opening Top Cover Open Lever Backing Paper Opening Front Panel 2 3 2 Rear View USB Interface Centronics Interface RS 232C DB 9 Interface Power Jack Power Switch Rear Label Guide WA 4m o du n Note The interface picture in the quick start guide is for reference only Please refer to the product specification for the interfaces availability 3 3 1 Setting Up the Printer 1 Place the printer on a flat secure surface 2 Make sure the power switch is off 3 Connect the printer to the computer with the Centronics or USB cable 4 Plug the DC power cord into the power jack at the rear of the printer and then plug the AC power cord into a properly grounded receptacle Note When plug power code into the rear of printer please make sure the printer p
3. Configuration Ui Calibrate Sensor r Printer Information B Version Ethernet Setup ram Com j Mil k m Check 5 Printer functions RTC Setup ERE eck Sum Fnnter Setup Print Test Page Speed Ribbon Reset Printer Density Code Page Factory Default Paper widthlunit Country Code Dump Text Paper Height unit Head up Sensor Ignore AUTO BAS Media Sensor x Reprint After Error Configuration Page Gapfunit Inten Gap Uffsetfunit Bline Inten Ready Post Print Action Continuous Inter Head Open Cut Piece Baud Rate Paper Jam Printer Status Out of Paper Reference Data Bits Ribbon End Err Direction Parity d Printer setup Ribbon Encoder Err Offset Pause Shift gt Stop Bit s Printing Other Error Shift Get Status Clear Load Save Set Read COMI 9500 N 8 1 RTs 2009 8720 FF 03 31 40 19 3 8 2 Printer Function Calibrate sensor Ethernet setup RTC setup 1 Select the PC interface connected with bar code printer 2 Click the Function button to setting 3 The detail functions in the Printer Function Group are listed as below KA GUNI Sensor Calibrate the sensor specified the Printer L alibrate Sensor Setup group media sensor field Setup the IP address subnet mask gateway Eth
4. and blinking Any red will do during the 5 blinks It will calibrate the gap black mark sensor sensitivity B The LED color will be changed as following order Amber gt red 5 blinks amber 5 blinks green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green B It calibrates the sensor and measures the label length Note Please select gap or black mark sensor by GAP or BLINE command prior to calibrate the sensor For more information about GAP and BLINE command please refer to TSPL2 programming manual Gap Black Mark 1 off the power switch Sensor Calibratio 2 Hold on the button then turn on the power switch Label Length Release the button when LED becomes amber and blinking Measurement Any amber will do during the 5 blinks Self Test and enter B The LED color will be changed as following order Dump Mode Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green lt calibrates the sensor and measures the label length and prints internal settings then enter the dump mode Note Please select gap or black mark sensor by GAP or BLINE command prior to calibrate the sensor For more information about GAP and BLINE command please refer to TSPL2 programming manual 38 Printer 1 Turn off the power switch Initialization 2 Hold on the button then turn on the power switch 3 Release the button when LE
5. cable to interface connected to the interface connector The serial port cable pin configuration Please replace the cable with pin to is not pin to pin connected pin connected The serial port setting is not consistent Please reset the serial port setting Not Printing between host printer The port specified in the Windows Select the correct printer port in the driver is not correct driver The Ethernet IP subnet mask gateway Configure the IP subnet mask is not configured properly gateway No print on the Follow the instructions in loading the Label loaded not correctly label media Continuous Please the initialization and printer setting go wrong mM feeding labels gap black mark calibration Gap black mark sensor sensitivity is Calibrate the gap black mark sensor not set properly sensor sensitivity is not enough Paper Jam Make sure label size is set properly et label size exactly as installed paper in the labeling software or program Labels may be stuck inside the printer Remove the stuck label mechanism near the sensor area Poor Print Quality Top cover is not closed properly Close the top cover completely and make sure the right side and left side levers are latched properly Check if supply is loaded correctly Reload the supply Check if dust or adhesives are Clean the print head accumulated on the print head Media are incompatible Change the label combination Ch
6. contact the Customer Service Department of your purchased reseller or distributor for assistance e LED Status This section lists the common problems that according to the LED status and other problems you may encounter when operating the printer Also it provides solutions LED Printer Possible Cause Recovery Procedure Status Status Color OFF response No power Turn on the power switch Check if the green LED is lit on power supply If it is not lit on power supply is broken Check both power connections from the power cord to the power supply and from the power supply to the printer power jack if they are connected securely oolid Green ON The printer is ready No action necessary mm ee Green with Pause The printer is paused Press the FEED button to resume for printing FUE Red with Error The out of labelor 1 Out of label blinking the printer setting is Load a roll of label and follow the instructions not correct in loading the media then press the FEED button to resume for printing 2 Printer setting is not correct nitialize the printer by instructions in Power on Utility or Diagnostic Tool Printer status can be easily shown on the Diagnostic Tool For more information about the Diagnostic Tool please refer to the instruction in the software CD disk Note 35 Print Guality Problem Possible Cause Recovery Procedure Check if interface cable is well He connect
7. gt red 5 blinks amber 5 blinks green 5 blinks gt green amber 5 blinks red amber 5 blinks gt solid green B It calibrates the sensor and measures the label length Note Please select gap or black mark sensor by GAP or BLINE command prior to calibrate the sensor For more information about GAP and BLINE command please refer to TSPL2 programming manual 27 4 2 Gap Black Mark Calibration Self test Dump Mode While calibrate the gap black mark sensor printer will measure the label length print the internal configuration self test and then enter the dump mode Please follow the steps as below 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED becomes amber and blinking Any amber will do during the 5 blinks The LED color will be changed as following order Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green B It calibrates the sensor and measures the label length and prints internal settings then enter the dump mode Note Please select gap or black mark sensor by Diagnostic Tool or by GAP or BLINE command prior to calibrate the sensor For more information about GAP and BLINE command please refer to TSPL2 programming manual 28 Self test Printer will print the printer configuration after gap black mark sensor calibration Self test printout can b
8. label to the external label feed opening through the rear label guide External Label Feed Opening Tees Rear Label Guide 4 Open the printer top cover by pulling the top cover open levers 5 Thread the label printing side face up through the label guide and place it on top the platen 6 Adjust the label guides by turning adjustment knob to fit the edge of the label backing 7 Close the printer top cover 3 6 Cutter Module Installation Option 1 Pull the top cover open levers to open the top cover 2 Remove the front panel from the lower cover 3 Remove 6 screws on the lower inner cover Screws Screws 4 Upside down the printer 5 Remove two screws at the hinge Sr 6 Remove the screw that fixes the memory card cover Screw 7 Plug in the Cutter Driver IC at U14 TDP 245 U30 TDP 245 Plus TDP 247 TDP 345 socket on the main board TDP 245 Model u o A 4 39525 a 0413 m TERIDA yi L Cutter Driver IC Note For Non RoHS PCB use cutter driver IC A3952SB For RoHS PCB use cutter driver IC A3953SB 8 Hold the lower cover and lift up the lower inner cover 9 Arrange the cutter module harness through the bezel 10 Connect the cutter module harness to the 4 pin socket on printer PCB Bezel Socket 11 RHeassemble lower inner cover back to the lower cover 12 Install the cutter module into the niche of the printer 16
9. 1 T 26 31 6D Dump mode printout Note Turn off and on the power switch to reset the printer for normal printing 30 4 3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults The only one exception is ribbon sensitivity which will note be restored to default Printer initialization is activated by the following procedures 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns green after 5 amber blinks Any green will do during the 5 blinks B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Printer configuration will be restore to defaults as below after initialization Gap Setting 0 127 3 0 Reference Point 0 0 upper left corner Note Always do gap black mark sensor calibration after printer initialization 31 4 4 Set Black Mark Sensor as Media Sensor Calibrate the Black Mark Sensor Please follow the steps as below 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns green amber after 5 green blinks Any green amber will do during the 5 blinks B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 bl
10. 13 Ressemble the parts the reverse order 14 Close the top cover 17 3 7 Loading Label Cutter Mode Open the printer top cover Insert the label spindle into label roller Place a label roll to label roll mount Thread the paper printing side face up through the label guide platen and cutter module paper outlet peo I9 Label Guide Cutter Paper Opening Adjustment Knob Platen Cutter 5 Adjust the black center biased label guides to fit edge of the label backing 6 Close the top cover 3 8 Diagnostic The Diagnostic Utility is toolbox that allows users to explore the printer s settings and status change printer settings download graphics fonts and firmware create printer bitmap fonts and to send additional commands to the printer Using this convenient tool you can explore the printer status and settings and troubleshoot the printer Note This utility works with printer firmware V6 00 and later versions 3 8 1 Start the Diagnostic Tool 1 Double click on the Diagnostic tool icon to start the software 2 There are four features Printer Configuration File Manager Bitmap Font Manager Command Tool included in the Diagnostic utility 001 Features tab Language 4 Trterace English TERN Printer Configuration File Manager Bitmap Font Manager Command Tool Interface rer err Fn 5 Printer
11. D turns green after 5 amber blinks Any green will do during the 5 blinks B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green e Always do gap black mark sensor calibration after printer initialization Set Black Mark 1 Turn off the power switch Sensor as Media 2 Hold on the button then turn on the power switch Sensor and 3 Release the button when LED turns green amber after 5 Calibrate the Black green blinks Any green amber will do during the 5 blinks Mark Sensor B The LED color will be changed as following Amber gt red 5 blinks amber 5 blinks green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green Set Gap Sensor as 1 Turn off the power switch Media Sensor and 2 Hold on the button then turn on the power switch Calibrate the Gap 3 Release the button when LED turns red amber after 5 Sensor green amber blinks Any red amber will do during the 5 blinks B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green 39 Skip AUTO BAS 1 Turn off printer power 2 Press the FEED button and then turn on power 3 Release the FEED button when LED becomes solid green B The LED color will be changed as following Amber g
12. TDP 245 TDP 245 Plus TDP 247 TDP 345 Series DIRECT THERMAL BAR CODE PRINTER USER S MANUAL Contents COPYRIGHT DECLARATION ccccccsscessseeceeccesseessseeeeeecssuecusseeceeeessseassseeeeeeessseassseeteeeessseassseeseees 1 COMPLIANCE San eine 1 DL 3 2s GUNO SIHA MR 3 2 1 Unpacking and 3 22 EQuibiment Checklisten e 3 na een AA 5 KIN NI WA EU UU TT 5 2 9 2 ia 5 OULD ae 6 Ssh oelulnG WP the Pfinier aan aus E D 6 32 LOAGCING kabel Stocker en ee 7 3 3 Peel Off Installation Assembly 9 3 4 Loading Label for Peel off Mode 12 3 5 External Label Roll Mount Installation 14 3 6 Cutter Module Installation 15 3 7 Loading Label in Cutter 18 3 8 PIGENI T velit a Deed 19 tarbthe DIagHosle TO0l AAA 19 3 8 2 Printer Function Calibrate sensor Ethernet setup RTC setup 20 3 9 Setting Ethernet by Diagnostic Utility 21 3 9 1 Using USB interface to setup Ethernet interfa
13. apacity Approved SD card manufacturer 128 MB SanDisk Transcend 256 MB SanDisk Transcend Panasonic 25 V1 0 V1 1 microSD 128 MB Transcend Panasonic The DOS FAT file system is supported for the SD card Folders files stored in the SD card should be in the 8 3 filename format The miniSD microSD card to SD card slot adapter is required 26 4 Power Utilities There six power on utilities to set up and test printer hardware These utilities activated by pressing FEED button and by turning on the printer power simultaneously The utilities are listed as below Gap Black mark sensor calibration Gap black mark sensor calibration Self test and Dump mode Printer initialization Set black mark as media sensor and calibrate the black mark sensor oet gap sensor as media sensor and calibrate the gap sensor Skip AUTO BAS EB UE CE ca 4 1 Gap Black Mark Sensor Calibration Gap black mark sensor sensitivity should be calibrated at the following conditions 1 A brand new printer 2 Change label stock 3 Printer initialization Please follow the steps below to calibrate the gap black sensor 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED becomes red and blinking Any red will do during the 5 blinks mit will calibrate the gap black mark sensor sensitivity B The LED color will be changed as following order Amber
14. ce 21 3 9 2 Using RS 232 interface to setup Ethernet interface 22 3 9 3 Using Ethernet interface to setup Ethernet interface 23 3 10 Install Memory 9 25 4 PoOWer ON bo En 27 4 1 Gap Black Mark Sensor Calibration essere 27 4 2 Gap Black Mark Calibration Self test Dump Mode 28 4 3 Printer 31 4 4 Set Black Mark Sensor as Media Sensor Calibrate the Black Mark Sensor 32 4 5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor 32 4 6 SKID AUTO BAS satin 32 5 MaMtenaN Es nee 33 ew eae 33 6 TFOUbIeShO0UNG eee E 35 E 36 7 LED and Button 00200202002 2 22 000000000 0000 55000000 37 P CED ER 37 7 2 B llon OPSTAO a 37 Yi 41 Copyright Declaration Information in this subject to change without notice and does not represent commitment on the part of TSC Auto ID Technology Co Ltd No part of this manual may be reproduced or transmitted in any form by any means for any purpose other than the purchaser s personal use without the expressed written permission of T TSC Au
15. e used to check if there is dot damage on the heater element printer configurations and available memory space Self test printout T INFO T m 7 Print head check pattern 1 1 i 1 Model name F W version 0000000 Vers TP IM Printed mileage meter MILAGE m Firmware checksum CHECKSUM 200000008 AF Serial port configuration CODE PAGE B50 Code page Country code DENSITY 8 Print speed inch sec 325 Print darkness TRANSPARENCE Label size inch DRAM FILE 8 FILE S Gap black mark sensor sensitivity FLASH FILE 60 FILE S Numbers of download files PHYSICAL DRAM MMKK AVAILABLE DRAM XXYM KBYTES FREE Total amp available memory space PHYSICRL FLRSH XXXX KBYTES AVAILABLE FLASH XXXX KBYTES FREE END OF FILE LIST 3e Rede dee EER RE ERD Bek dede he desk debe de Note 1 The physical flash memory for RoHS compliant version is 2MB Flash and 2MB DRAM TDP 245 Model 8MB SDRAM TDP 245 Plus TDP 247 TDP 345 Model 2 System occupies 960 KB in Flash memory so total flash memory space for user downloading is 1088 KB 3 System occupies 1792 KB in DRAM so total DRAM memory space for user downloading is 256 KB TDP 245 Model System occupies 7936 KB in SDRAM so total SDRAM memory space for user downloading is 256 KB TDP 245 Plus TDP 247 TDP 345 Model 29 Dump mode Printer will enter dump mode after printing pri
16. eck if print density is set properly an the print density and print speed Check print head test pattern if head Run printer self test and check the print head test pattern if there is dot element is damaged missing in the pattern 36 7 LED Button Operation This printer has one button and one three color LED indicator By indicating the LED with different color and pressing the button printer can feed labels pause the printing job select and calibrate the media sensor print printer self test report reset printer to defaults initialization Please refer to the button operation below for different functions 7 1 LED LED Color Green Solid This illuminates that the power is on and the device is ld cro RM Green Flash This illuminates that the system is downloading data in Amber This illuminates that the system is clearing data from printer Red Solid This illuminates printer head open cutter error Hed Flash This illuminates a printing error such as head open paper empty paper jam or memory error etc 7 2 Button Operation Press the button when the LED is green B It feeds the label to the beginning of the next label Press the feed button during printing B The printing job is suspended 37 Gap Black Mark 1 off the power switch Sensor Calibration 2 Hold on the button then turn on the power switch 3 Release the button when LED becomes red
17. ernet Setup Ethernet Setup for the on board Ethernet Please refer to next HIC Setup section Print Test Page RTC Time Synchronize printer Real Time Clock with PC Reset Printer Print Test Page Print a test ooo Factory Default Reset Printer Reboot Reboot printer Dump Text Factory Default ae and restore the settings to Dump To activate the printer dump mode Configuration Page Ignore AUTO BAS Ignore the downloaded AUTO BAS program Configuration Page Print printer configuration Note For more information about Diagnostic Tool please refer to the diagnostic utility quick start guide in the CD disk Utilities directory 20 3 9 Setting Ethernet by Diagnostic Utility Option The Diagnostic Utility is enclosed in the CD disk Utilities directory Users can use Diagnostic Tool to setup the Ethernet by RS 232 USB and Ethernet interfaces The following contents will instruct users how to configure the Ethernet by these three interfaces 3 9 1 Using USB interface to setup Ethernet interface 1 Connect the USB cable between the computer and the printer 2 Turn on the printer power 3 Start the Diagnostic Utility by double clicking on the DiagToolexe icon Note This utility works with printer firmware V6 00 and later versions 4 The Diagnostic Utility default interface setting is USB interface If USB interface is connected with printer no other settings need to be changed in the
18. inks gt green amber 5 blinks gt red amber 5 blinks gt solid green 4 5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor Please follow the steps as below 1 Turn off the power switch 2 Hold on the button then turn on the power switch 3 Release the button when LED turns red amber after 5 green amber blinks Any red amber will do during the 5 blinks B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green 4 6 Skip AUTO BAS TSPL2 programming language allows user to download an auto execution file to flash memory Printer will run the AUTO BAS program immediately when turning on printer power The AUTO BAS program can be interrupted without running the program by the power on utility Please follow the steps as below 1 Turn off printer power 2 Press the FEED button and then turn on power 3 Release the FEED button when LED becomes solid green B The LED color will be changed as following Amber gt red 5 blinks gt amber 5 blinks gt green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green 4 Printer will be interrupted to run the AUTO BAS program 32 5 Maintenance 5 1 Cleaning This session presents the clean tools and methods to maintain your printer Please use one of following material to clean the printer Cotton swab Head cleaner
19. interface field Interface ETHERNET 5 Click on the Ethernet Setup button from Printer Function group in Printer Configuration tab to setup the IP address subnet mask and gateway for the on board Ethernet Printer Function t Static IP Calibrate Sensor Ethernet Setup Setup Print Test Page ee ee see ore Printer PS FFDME Printer Mame Factory Default een MAC Address I Dump Text Ignore AUTO BAS Configuration Page Set Printer Set P Cancel 21 3 9 2 Using RS 232 interface to setup Ethernet interface 1 Connect the computer and the printer with a RS 232 cable 2 Turn on the printer power 3 Start the Diagnostic Utility by double clicks on the DiagToolexe ICON Note This utility works with printer firmware V6 00 and later versions 4 Select as interface then click on the Setup button to setup the serial port baud rate parity check data bits stop bit and flow control parameters ETHERNET RS232 Setup COM Port Baud Hate Bits Parity Check Stop Bit s Hardware Handshaking Software Handshaking Cancel 5 Click on the Ethernet Setup button from printer function of Printer Configuration tab to setup the IP address subnet mask and the gateway for the on board Ethernet Printer Function Calibrate Sens
20. nter configuration In the dump mode all characters will be printed 2 columns as following The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters It allows users or engineers to verify and debug the program SPEED 2 0 53 60 45 45 44 20 32 2E 30 OD DENSITY 8 44 45 4E 53 49 54 59 20 38 SET PEEL 8A 53 45 54 20 50 45 45 4C OFF DIRE 28 4F 46 46 OD BA 44 49 52 45 CTION 43 54 49 4F 4E 20 30 QA 47 AP mm 50 28 33 2E 380 38 20 6D 60 mm REFERENCE bz 45 46 4 52 45 4E 43 45 28 90 808 SET UTTER 55 54 54 45 52 20 46 46 GC SIZE 180 BA 53 48 45 20 31 30 38 E 02 mm 65 9 38 32 28 6D 8D 2 36 35 ZE 30 4 mm CLS 34 20 6D 60 D 43 4C 53 BD BARCODE 1 BA 42 41 52 43 4F 44 45 20 31 ET PEEL OF 45 54 20 50 45 45 4C 20 46 DIRECTI 46 OD 44 49 52 45 43 54 49 ON GAP 4E 20 30 BD OA 47 41 50 20 3 08 0 33 2E 30 28 ED 2C 39 60 mm REF 30 30 20 6D 6D OD OA 52 45 46 ERENCE 6 0 45 52 45 4E 43 45 20 30 2C 30 SET OD 53 45 54 20 43 55 54 54 ZE 1080 02 45 20 31 30 30 2E 30 32 20 mm 65 04 m 60 6D 2C 36 35 2 30 34 20 6D BA 6D OD 43 4C 53 BA 42 41 RCODE 144 2 43 44 46 20 31 34 34 2C 149 39 1 31 34 39 2C 22 33 39 22 2C 31 0 1 0 2 6 32 30 20 31 2 30 26 32 20 36 67114387T 2 22 35 37 31 31 34 33 38 54 PRINT 1 22 00 BA 50 52 49 4E 54 20 3
21. or Ethernet Setup AIC Setup Print Test Page Reset Printer Dump Text Ignore AUTO BAS Configuration Page Factory Default ER uipnarnat jui C Static IP Subnet Mask Gateway MAC Address 00 1 82 4 2 Set Printer Name Set Cancel 22 3 9 3 Using Ethernet interface to setup Ethernet interface 1 Connect the computer and the printer to the LAN 2 Turn on the printer power 3 Start the Diagnostic Utility by double clicks on the icon Note This utility works with printer firmware V6 00 and later versions 4 Select Ethernet as the interface then click on the Setup button to setup the IP address subnet mask and gateway for the on board Ethernet Interface ETHERNET IP Address Model Mame SERERE IEEE Ready INLET EWE FS L75730 00 16 11 C7 67 90 10 0 6 24 DP 3321 Ready fi 0 0 6 125 ETHERNET Fort 00 Discover Device Change IP Address Factor Default Web Setup 5 Click the Discover Device button to explore the printers that exist on the network 6 Select the printer in the left side of listed printers the correspondent IP address will be shown in the right side IP address Printer field 7 Click Change Address to configure the IP address obtained by DHCP or Static jai Subnet Mask Gateway J LI b 23 Printer TT033 50 Address 100 18 02 FF 02 0C Set P
22. ower switch is off USB i Power Switch Centronics Rs 232 Power Jack Power Supply Power Cord 3 2 Loading Label Stock 1 Insert a 1 label spindle into a paper roll If your paper core is 1 inch remove the 1 5 inch core adapter from the fixing tab 1 5 Core Adapter 1 Printing Side Face up Label Roll Fixing Tab 1 Label Spindle 2 Open the printer s top cover by releasing the green top cover open levers located on both sides of the printer and lifting the top cover 3 Place a roll of paper into internal paper roll mount 4 Feed the paper printing side face up through the label guides and place the label over the platen 5 Adjust the black center biased label guides in or out by turning adjustment knob so they are slightly touch the edges of the label backing Label Guide Label Roll Mount Adjustment Knob Platen 6 Close the printer top cover slowly and make sure the cover locks levers securely Note Failure to securely close and lock the cover will result in poor print quality 3 3 Peel Off Installation Assembly Option 1 Open the top cover 2 Unscrew the 6 screws in the lower inner cover Screws Screws 3 Upside down the printer 4 Unscrew the 2 screws at the lower inner cover lt Remove the screw Remove the screw 5 Remove the screw at memory card cover Screw 6 Hold the lower cover and lift up the top cover opening levers to separate the lower
23. pen Lint free cloth Vacuum Blower brush 10096 ethanol The cleaning process is described as following Printer Part Metha intel 1 Always turn off the printer Clean the print head when before cleaning the print head changing a new label roll 2 Allow the print head to cool for a minimum of one minute 3 Use a cotton swab Head cleaner pen and 100 ethanol to clean the print head surface Print Head Print Head Md E ERES Element Head Cleaner Pen 1 Turn the power off Clean the platen roller when 2 Rotate the platen roller and changing a new label roll Platen Roller wipe it thoroughly with 100 ethanol and a cotton swab or lint free cloth Tear Bar Peel Use the lint free cloth with 100 needed Sensor Compressed air or vacuum Monthly Exterior Wipe it with water dampened 33 Interior Brush vacuum As needed Note e Do not touch printer head by hand If you touch it careless please use ethanol to clean it e Please use 100 Ethenol DO NOT use medical alcohol which may damage the printer head e Regularly clean the print head and supply sensors once change a new ribbon to keep printer performance and extend printer life 34 6 Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer If the printer still does not function after all suggested solutions have been invoked please
24. rinter Name Set IP Cancel 23 default address is obtained by DHCP change the setting to static address click Static radio button then enter the IP address subnet mask and gateway Click Set IP to take effect the settings Users can also change the Printer Name by another model name in this fields then click Set Printer Name to take effect this change Note After clicking the Set Printer Name or Set button printer will reset to take effect the settings Click Exit button to exit the Ethernet interface setup and go back to Diagnostic Tool main screen Factory Default button This function will reset the IP subnet mask gateway parameters obtained by DHCP and reset the printer name Web setup button Except to use the Diagnostic Utility to setup the printer you can also explore and configure the printer settings and status or update the firmware with the IE or Firefox web browser This feature provides a user friendly setup interface and the capability to manage the printer remotely over a network 24 3 10 Install Memory 1 Upside down the printer 2 Remove 1 screw and open the memory card cover Memory Card TDP 245 Model TDP 245 Plus TDP 247 TDP 345 Model Option SD card tae ww wi Y Y 7212 4 Revert the memory card cover Recommended SD card specification SD card c
25. sch der Batterie Ersatz nur durch denselben oder einem vorn Hersteller empfohlenem nlichen Typ Entsorgung gebrauchter Batterien nach Angaben des Herstellers 1 Introduction Thank you for purchasing the TSC TDP 245 245 Plus 247 345 Series Direct Thermal Bar Code Printer Although it is a compact desktop printer it is reliable and with superior throughput performance This printer provides direct thermal printing at user selectable speed of 2 0 3 0 4 0 5 0 6 0 or 7 0 inches per second lt accepts roll feed die cut and fan fold labels for direct thermal printing All common bar codes formats are available Fonts and bar codes can be printed in 4 directions 8 different alohanumeric bitmap fonts and a build in true type font capability You will enjoy high throughput for printing labels with this printer 2 Getting Started 2 1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping Please carefully inspect the packaging and printer upon receiving the bar code printer Please retain the packaging materials in cover you need to reship the printer 2 2 Equipment Checklist Printer BarTender UltraLite CD disk Quick start guide USB port cable External universal switching power supply Power Cord Label Spindle Fixing tab x2 1 5 core adapter x2 If any parts are missing please contact the Customer Service Department of your purchased reseller or distributor Dealer option
26. t red 5 blinks gt amber 5 blinks green 5 blinks gt green amber 5 blinks gt red amber 5 blinks gt solid green 4 Printer will be interrupted to run the AUTO BAS program 40 Revise History Dae Conten Editor Revise the section 3 8 Internal Ethernet Print Server Camille Module Installation Option 2008 2 29 Add section 3 9 Diagnostic Tool Add the IP Address default setting Add section 3 10 Install Memory Card Camille 2008 3 5 Revise the sections 3 3 and 3 8 Revise the default setting 2009 3 11 Revise section 3 10 Recommended SD card Camille specification 2009 10 14 Revise section 3 9 Camille LN 2010 7 28 Revise section 2 3 2 2010 8 13 Revise compliances section 2011 1 14 emove internal Ethernet print server module installation Camille section 2011 1 25 Modify TSC address 2010 3 5 Revise compliances section Camille Revise section 3 1 4 TSC Auto Technology Co Lt PAA OOG A 2218 9878 Corporate Headquarters 9F No 95 Minquan Rd Xindian Dist New Taipei City 23141 Taiwan R O C TEL 886 2 2218 6789 Web site www tscprinters com E mail printer_sales tscprinters com tech support 2tscprinters com Li Ze Plant No 35 Sec 2 Ligong 1st Rd Wujie Township Yilan County 26841 Taiwan R O C TEL 886 3 990 6677 FAX 886 3 990 5577
27. to ID Technology Co Ltd Compliances CE Class B EN55022 1998 A1 2000 2 2003 EN55024 1998 A1 2001 2 2003 IEC 61000 4 Series EN61000 3 2 2006 amp EN61000 3 3 1995 A1 2001 FCC Part 15 Class B UL CUL C Tick CFR 47 Part 15 CISPR 22 3 Edition 1997 Class ANSI C63 4 2003 Canadian ICES 003 TUV Safety EN60950 2000 Wichtige Sicherheits Hinweise 1 Bitte lesen Sie diese Hinweis sorgfaltig durch 2 Heben Sie diese Anleitung fur den spateren Gebrauch auf 3 Vor jedem Reinigen ist das Gerat vom Stromentz zu trennen Verwenden Sie keine Flussig oder Aerosolreiniger Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung 4 Die NetzanschluB Steckdose soll nahe dem Gerat angebracht und leicht zug nglich sein 5 Das Gerat ist vor Feuchtigkeit zu sch tzen 6 Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Besch digungen hervorrufen 7 Beachten Sie beim Anschlu ans Stromnetz die Anschlu werte 8 Dieses Ger t kann bis zu einer Au entemperatur von maximal 40 C betrieben werden CAUTION 1 HAZARDOUS MOVING PARTS IN CUTTER MODULE KEEP FINGER AND OTHER BODY PARTS AWAY 2 THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HAS LITHIUM BATTERY CR2032 INSTALLED RISK OF EKPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE 3 DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER INSTRUCTIONS ORSICHT Explasiansgetahr bel unsachgemen Austau

Download Pdf Manuals

image

Related Search

Related Contents

Service_Training_2007-03-26_1 575.07 KB  Tarox 0907031 notebook  Vogel's PFW 5833  Faits divers sur les produits chimiques pour faire  仕様書[PDF:113KB]  Guide de dépannage de Java Desktop System Version 2  Bedienungsanleitung  PRO BASIC - Besøg masterpiece.dk    Portail http  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.