USER MANUAL
Contents
1. USER MANUAL Pro Lrte LCD Monitor Prolrte T3234MSC Thank you very much for choosing the iiyama LCD monitor We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor Please keep this manual in a safe place fo your future reference Servicecard 5 a 9 50 por Dear user we congratulate you on the purchase of your iiyama LCD For details on warranty and locally used pixel policies that apply directly after installation of your product please check the iiyama website To report a fault please contact your local support centre found at www iiyama com service Things to check before you call the iiyama information line if the power cable is connected securely and turned on if the display has been turned on if the signal cable is connected securely and the correct input selected if the computer has been restarted with the display connected if the graphics card is correctly installed with the latest drivers possible if the correct native resolution has been selected via Display Properties If the R G B signal configuration is correct if the displays On Screen Menu is shown if the correct brightness and contrast settings have been set if given display tolerances and compatibility have been considered if via the On Screen Menu you have performed a Factory Reset Recall Before reporti2. Null modem cable Null modem cable Not supplied Two RS 232C Ports are reserved for this option Before using the remote control function design a custom firmware based on your own application program and communication protocol BEFORE YOU OPERATE THE MONITOR 9 ENGLISH Rotating the Display It is designed to be compatible in both landscape and portrait modes however it is optimized for landscape mode Note that the OSD orientation cannot be changed in the OSD menu r Available r Not Available r Landscape i Portrait TOUCH SCREEN DRIVER INSTALLATION This monitor is available with USB connection 1 This monitor is Microsoft Windows HID Human Interface Device compatible if you use the USB touch screen interface No additional software driver is required for general operation of the touch screen 2 For this monitor the system requires 15 seconds for Windows 7 to install uninstall the touch drivers while turning power ON OFF or PLUGGING UNPLUGGING USB cable 3 Support OS Windows 8 Windows 7 Windows Vista single touch only Calibration Tool Install This tool in the attached Touch Panel Driver Disk When using the monitor for the first time install tool without fail and please execute calibration tool 1 Open the Touch Panel Driver Disk CD ROM 2 Select ProLite MSC MC series 3 Click 32 4 Please clcik Calibration to start it
3. db x m 17 ord 9300 6500 RED 94 5500 GREEN Emm 90 7500 BLUE 100 USER Adjustment Item Problem Option Button to Press 9300 Bluish white 6500 Reddish white 5500 Greenish white COLOR TEMP 7500 Yellowish white RED k user GREEN 100 weak BLUE I TE A 2 Hl it amp 4 VOLUME MUTE Adjustment Item Problem Option Button to Press ft VOLUME 2 A Too loud C 7 Turn off the sound temporarily OFF Return the sound volume to the previous level You can skip the Menu items and display an adjustment scale directly by using the following button operations MUTE Press the V Button when the Menu is not displayed id MUTE ON MUTE OFF 16 OPERATING THE MONITOR SCREEN ADJUSTMENTS Adjust the image by following the procedure below to get the desired picture when selecting Analog input W The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use The monitor is designed to provide the best performance at resolution of 1920 x 1080 but can not provide the best at resolutions of less than 1920 x 1080 because the picture is automatically stretched to fit the full screen It is recommended to operate at resolution of 1920 x 1080 in normal use Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to the screen enlargement p
4. 750 Positive Digital DVI Digital Visual Interface Standard Rev 1 0 compliance Input Audio Connector 0 3 5mm mini jack Stereo Input Audio Signal 1 0Vrms maximum Output Audio Connector 0 3 5mm mini jack Stereo Speakers 8W x 2 Stereo speakers Maximum Screen Size 698 4mm W x 392 8mm H 27 5 W x 15 5 H Power Source 100 240VAC 50 60Hz 1 2A Power Consumption 65W typical Power management mode 2W maximum Dimensions Net Weight 786 0 x 480 5 x 69 0mm 30 9 x 18 9 x 2 7 WxHxD 16 2kg 35 7lbs Environmental Operating Temperature 5 to 35 C 41 to 95 F Considerations Humidity 20 to 8096 No condensation Storage Temperature 20 to 60 4 to 140 Humidity 10 to 90 No condensation Approvals CE T V Bauart CU IPX1 28 USB peripherals Audio equipment are not connected PX1 Standard Compliant Only front face APPENDIX 23 ENGLISH ENGLISH SPECIFICATIONS ProLite T3234MSC B2X ProLite T3234MSC B2 Model Name ProLite 3234 5 2 ProLite T3234MSC B2 Touch Technology Projected capacitive 10pt touch Projected capacitive 2pt touch Screen Light transmission 909 Communication USB serial transfer system Size Category 32 LCD Panel Driving system a Si TFT Active Matrix Size Diagonal 31 5 80cm Pixel pitch 0 364mm H x 0 364mm V Brightness 350cd m Typical 315cd m
5. 24 SPECIFICATIONS ProLite T3234MSC B3X 25 DIMENSIONS ProLite 3234 9 1 26 DIMENSIONS ProLite 3234 5 2 ProLite T3234MSC B2 ProLite T3234MSC B3xX 26 COMPLIANT TIMING FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke strange sounds or fumes unplug the monitor and contact your dealer or iiyama service center immediately Further use may be dangerous and can cause fire or electric shock NEVER REMOVE THE CABINET High voltage circuits are inside the monitor Removing the cabinet may expose you to the danger of fire or electric shock DO NOT PUT ANY OBJECT INTO THE MONITOR Do not put any solid objects or liquids such as water into the monitor In case of an accident unplug your monitor immediately and contact your dealer or iiyama service center Using the monitor with any object inside may cause fire electric shock or damage INSTALL THE MONITOR ON A FLAT STABLE SURFACE The monitor may cause an injury if it falls or is dropped DO NOT USE THE MONITOR NEAR WATER Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric shock OPERATE UNDER THE SPECIFIED POWER SUPPLY Be sure to operate the monitor only with the specified power supply Use of an incorrect voltage will cause malfunction and may cause fi
6. button operations are aborted during adjustment On Screen Display disappears when the time set for the OSD TIMEOUT has passed W MENU button can be used to return previous menu item W Any changes are automatically saved in the memory when the On Screen Display disappears Turning off the power should be avoided while using the Menu W Adjustments for H V POSITION H SIZE and FINE are saved for each signal timing Except for these adjustments all other adjustments have only one setting which applies to all signal timings 12 OPERATING THE MONITOR ADJUSTMENT MENU CONTENTS AK E it SK CONTRAST Xt BRIGHTNESS 1280x1024 FH 63KHz FV 59 9Hz 5 Adjustment Item Problem Option Button to Press Too dull Too intense amp 7 Too dark BRIGHTNESS 23 Too bright ev Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright You can skip the Menu items and display an adjustment scale directly by using the following button operations BRIGHTNESS Press the A Button when the Menu is not displayed CONTRAST Press the V Button when the Menu is not displayed LOCK MODE Press the MENU button to display the OSD menu Pressing and holding the MENU button again and press the Power Switch The OSD menu is not displayed when the OSD is locked Pressing and holding the MENU button again and press the Power Switch The followin
7. to disrupt it with a motion picture 2 It is recommended to periodically change the background colour and background image 3 It is recommended to operate the display for maximum 18 hours per day 4 If the screen is active for a longer period of time it is recommended to Run the screensaver motion picture or black pattern Il Power off the system for a while b Make sure that the screen is suitably ventilated or is used in conjunction with climate control system if installed into any bespoke cabinets 6 We strongly recommend an active cooling system with fans for long operating times especially for high luminance LCD models W This LCD cannot be used outdoors m This LCD cannot be used with the screen facing upwards W f you use a cable longer than the supplied one the picture quality is not guaranteed Touch function can be disrupted if the USB cable length exceeds 3m FOR YOUR SAFETY 3 ENGLISH ENGLISH CUSTOMER SERVICE NOTE W f you have to return your unit for service and the original packaging has been discarded please contact your dealer or iiyama service center for advice or replacement packaging CLEANING ACE m If you drop any materials or liquids such as water into the monitor when cleaning unplug the power cable immediately and contact your dealer or iiyama service center JA Ie M For safety reasons turn off the power switch and unplug the monitor before you clean it NOTE W To prot
8. wallpaper setting dialogue box If you use Microsoft PLUS 95 98 cancel the setting of Stretch desktop wallpaper to fit the screen Adjustment pattern Zebra pattern OPERATING THE MONITOR 17 Press the SELECT Button AUTO ADJUST Adjust the image manually by following procedure below when the screen has a flicker or blur or the picture does not fit in the display area after performing the Auto Adjust 5 Adjust the V POSITION so that the top and bottom of the picture frame will fit to the display area ENGLISH 1 Adjust the H POSITION so that the left side of the picture frame will move to the left edge of the display area 2 Stretch the right side of the picture frame to the right edge of the display area by adjusting the H SIZE m When the left side of the picture frame moves apart from the left edge of the display area during the H SIZE adjustment adjust steps 1 and 2 W Another way to make the H SIZE adjustment is to correct the vertical wavy lines in the zebra pattern W The picture may flicker during the H SIZE H V POSITION adjustment W In case the picture frame is bigger or smaller than the data display area after the H SIZE adjustment repeat steps from 18 OPERATING THE MONITOR Adjust the FINE to correct horizontal wavy noise flicker or blur in the
9. Audio equipment are not connected PX1 Standard Compliant Only front face 24 APPENDIX SPECIFICATIONS ProLite T3234MSC B3X Projected capacitive 30pt touch 90 USB serial transfer a Si TFT Active Matrix Diagonal 31 5 80cm 0 364mm H x 0 364mm V 450cd m Typical 405cd m with Touch panel 3000 1 Typical with Touch panel Horizontal 178 degrees Vertical 178 degrees Typical 8ms Gray to Gray Typical Approx 16 7M Horizontal 31 47 67 50kHz Vertical 47 63Hz 1920 x 1080 2 1 MegaPixels VGA D sub mini 15 pin DVI D 24 pin RS 232C In Out VESA DDC2B Separate sync TTL Positive or Negative Analog 0 7Vp p Standard 75Q Positive Digital DVI Digital Visual Interface Standard Rev 1 0 compliance 0 3 5mm mini jack Stereo 1 0Vrms maximum 0 3 5mm mini jack Stereo 8W x 2 Stereo speakers 698 4mm W 392 8mm H 27 5 W x 15 5 H 100 240VAC 50 60Hz 1 2A 65W typical Power management mode 2W maximum 781 5 x 476 0 x 69 5mm 30 8 x 18 7 x 2 7 WxHxD 16 2kg 35 7165 Operating Temperature 5 to 35 C 41 to 95 F Humidity 20 to 80 No condensation Storage Temperature 20 to 60 C 4 to 140 F Humidity 10 to 90 No condensation CE T V Bauart CU IPX1 0 USB peripherals Audio equipment are not connecte
10. Do not touch the screen during executing calibration tool 5 After a few seconds calibration is completed and Calibration OK message is displayed 6 Exit to close the calibration tool 10 BEFORE YOU OPERATE THE MONITOR COMPUTER SETTING m Signal Timing Change to the desired signal timing listed on page 27 COMPLIANT TIMING W Windows 95 98 2000 Me XP Vista 7 Plug amp Play The iiyama LCD monitor complies with DDC2B of VESA standard The Plug amp Play function runs on Windows 95 98 2000 Me XP Vista 7 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied For installation on Windows 95 98 2000 Me XP The monitor Information File for iiyama monitors may be necessary for your computer and obtained via the Internet using the address http www iiyama com For additional information on how to download the driver for your touch screen monitor please access the internet site noted above W Monitor Drivers are not required in most cases for Macintosh or Unix operating Systems For further information please contact your computer dealer first for advice W Procedure for turning ON the Power Switch Turn ON the monitor first and then the computer W Touch screen driver software Touch screen driver software and system may not start when you start your computer while touching the screen Touch screen driver software may not run due to the power saving function depending on the BIOS of your computer In this
11. case set the power saving function to off BEFORE YOU OPERATE THE MONITOR 11 ENGLISH ENGLISH OPERATING THE MONITOR To create the best picture your LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 27 You are also able to adjust the picture by following the button operation shown below For more detailed adjustments see page 17 for SCREEN ADJUSTMENTS Press the MENU Button to start the On Screen Display feature There are additional Menu items which can be switched by using the A V Buttons es 5 d 2 CONTRAST Xt BRIGHTNESS 1280x1024 FH 63KHz FV 59 9Hz Select the Menu item which contains the adjustment icon relating to the adjustment you want to make Use the SELECT Button to highlight the desired adjustment icon Use the A V Buttons to make the appropriate adjustment or setting Press the MENU Button to leave the menu and the settings you just made would be automatically saved For example to correct for vertical position select Menu item of 28 Then select V POSITION by using the SELECT Button Use the A V Buttons to change the vertical position settings The vertical position of the overall display should be changing accordingly while you are doing this gt AUTO ADJUST CBH POSITION H SIZE FINE TT Press the MENU Button lastly it ends all changes are saved in the memory When
12. cial cable is required please contact your local iiyama dealer or regional iiyama office W For connection to Macintosh computers contact your local iiyama dealer or regional office for a suitable adaptor W Make sure you tighten the finger screws at each end of the Signal Cable Example of Connection Back Remote 8 Control OSD Key llo Power Cable option Accessory j o USB Cable Accessory Ld S lt gt Audio Cable Accessory gt VGA D sub Signal Cable Accessory ile DVI D Signal Cable Accessory Computer 8 BEFORE YOU OPERATE THE MONITOR Fitting and Removal of Cable Cover Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down lt Removal gt Remove the cable cover as shown in Step 1 lt Fitting gt When cables are connected as shown in Step 2 1 or Step 2 2 place the cable cover and fix it firmly using a screw Cable Cover ENGLISH Controlling the Monitor via RS 232C Remote Control The monitor can be controlled by connecting a PC with a RS 232C terminal Use the Null modem cable to enable it Computer Monitor Monitor 4 RS 232C RS 232C 4 4 RS 232C RS 232C 4 ee Output Input
13. d PX1 Standard Compliant Only front face APPENDIX 25 ENGLISH ENGLISH DIMENSIONS ProLite T3234MSC B1 69 0mm 2 7 786 0mm 30 9 44 0mm 1 7 698 5mm 27 5 25 0mm 1 0 __ a 393 5mm 15 5 480 5mm 18 9 DIMENSIONS ProLite T3234MSC B2X ProLite T3234MSC B2 ProLite T3234MSC B3X 781 5mm 30 8 69 5mm 2 7 698 5mm 27 5 44 5 1 7 393 5mm 15 5 476 0 18 7 26 APPENDIX COMPLIANT TIMING Video Mode Horizontal Vertical Dot Clock Frequency Frequency VGA 640 x 480 31 469kHz 59 940Hz 25 175MHz 35 156kHz 56 250Hz 36 000MHz SVGA 800 600 37 879kHz 60 317Hz 40 000MHz XGA 1024 x 768 48 363kHz 60 004Hz 65 000MHz 1280 x 720 44 720kHz 60 000Hz 74 500MHz VESA 1280 x 768 47 776kHz 59 870Hz 79 500MHz 1280 x 960 60 000kHz 60 000Hz 108 000MHz SXGA 1280x1024 63 981 2 60 020Hz 108 000MHz 1366 x 768 47 712kHz 59 790Hz 85 500MHz WXGA 1440 x 900 55 935kHz 59 887Hz 106 500MHz WSXGA 1680 1050 65 290kHz 59 954Hz 146 250MHz Full HD 1920 1080 67 500kHz 60 000Hz 148 500MHz APPENDIX 27 M100G21 ENGLISH
14. e Button V Select Auto Button SELECT Power Switch b 6 Power Indicator Aei Green Normal operation Orange Power Management USB Connector USB RS232C output Connector COM OUT 9 RS232C input Connector IN q GOOD Remote Control hg Key ENGLISH Remote Control OSD Key Connector Remote Key Audio output Connector AUDIO OUT Audio input Connector AUDIO IN 19 VGA D sub mini 15pin Connector VGA IN DVI D 24pin Connector DVI IN AC Connector AC IN Speakers Remote Control OSD key is optional BEFORE YOU OPERATE THE MONITOR 7 ENGLISH CONNECTING YOUR MONITOR Ensure that both the computer and the monitor are switched off Connect the computer to the monitor with the signal cable 8 Connect the computer to the monitor with the USB Cable Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features 5 Connect the monitor cable to the Remote Control OSD key option if necessary Connect the Power Cable to the monitor first and then to the power supply Turn on your monitor and computer W The signal cables used for connecting the computer and monitor may vary with the type of computer used An incorrect connection may cause serious damage to both the monitor and the computer The cable supplied with the monitor is for a standard connector If a spe
15. e are not guaranteed CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package Check to see if they are enclosed with the monitor If anything is missing or damaged please contact your local iiyama dealer or regional office m Power Cable 2pcs m VGA D sub Signal Cable i DVI D Cable USB Cable W Audio Cable W Screw M3x6mm m Touch Panel Driver Disk CD ROM W Safety Guide m Quick Start Guide The rating of the Power Cable enclosed 120V area is 10A 125V If you are using a power supply higher than this rating then a power cable with a rating of 10A 250V must be used However all guarantees and warranties are void for any problems or damage caused by a power cable not supplied by iiyama This CD ROM contains the touch screen driver software BEFORE YOU OPERATE THE MONITOR 5 ENGLISH ENGLISH WALL MOUNTING When you use with the wall mounting in consideration of thickness of the mounting stage tighten the M6 Screw with washer which L length is 14mm to fasten the monitor Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor Screw Mounting Stage L Chassis 6 BEFORE YOU OPERATE THE MONITOR CONTROLS CONNECTORS lt Front gt Menu Button MENU 2 Scroll Up Brightness Button A 3 Scroll Down Mut
16. ect the LCD panel do not scratch or rub the screen with a hard object W Never use any of the following strong solvents These will damage the cabinet and the LCD screen Thinner Benzine Abrasive cleaner Spray type cleaner Wax Acid or Alkaline solvent W Touching the cabinet with any product made from rubber or plastic for a long time may cause degeneration or loss of paint on the cabinet CABINET Stains can be removed with a cloth lightly moistened with a mild detergent solvent Then wipe the cabinet with a soft dry cloth LCD Periodic cleaning with a soft dry cloth is recommended SCREEN Don t use tissue paper etc because these will damage the LCD screen 4 BEFORE YOU OPERATE THE MONITOR BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1920 1080 High Contrast 3000 1 Typical Brightness 350cd m Typical ProLite T3234MSC B1 ProLite T3234MSC B2 ProLite T3234MSC B2X High Contrast 3000 1 Typical Brightness 450cd m Typical ProLite T3234MSC B3X Digital Character Smoothing Automatic Set up Plug amp Play VESA DDC2B Compliant Windows 95 98 2000 Me XP Vista 7 Compliant Power Management VESA DPMS Compliant VESA Mounting Standard 400mmx200mm Compliant IPX1 Standard Compliant Only front face 9 999 99 m Windows8 touch environment Basic touch operations can be performed under Windows 8 However please be informed that full touch functionality and normal operational performanc
17. ed This may cause fire or damage Operating the monitor on its back side upside down or on a carpet or any other soft material may also cause damage DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR When you move the monitor turn off the power switch unplug the monitor and be sure the signal cable is disconnected If you do not disconnect them it may cause fire or electric shock UNPLUG THE MONITOR If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents HOLD THE PLUG WHEN DISCONNECTING To disconnect the power cable or signal cable always pull it by the plug Never pull on the cable itself as this may cause fire or electric shock DO NOT TOUCH THE PLUG WITH WET HANDS Pulling or inserting the plug with wet hands may cause electric shock WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER Be sure the computer is strong enough to hold the weight of the monitor otherwise you may damage your computer CARE TO A HAND AND FINGERS W Careful attention is required not to catch your fingers or hands when you change the height or the angle W Injury can occur if care is not taken to avoid finger contact with the displays base when adjusting the height Just for height adjustable model REMARK FOR 24 7 USAGE This product is not specifically designed for 24 7 usage in all environments OTHERS ERGONOMIC RECOMMENDATIONS To eliminate eye fatigue do not operate the monitor agains
18. eyboard or the mouse are touched again NORMAL MODE POWER MANAGEMENT MODE POWER 0 10096 CONSUMPTION W Even when using the power management mode the monitor consumes electricity Turn off the Power Switch whenever the monitor is not in use during the night and weekends to avoid unnecessary power consumption E It is possible that the video signal from the computer may be on while the H or V sync signal is missing In this instance the POWER MANAGEMENT feature may not work properly 20 OPERATING THE MONITOR TROUBLE SHOOTING If the monitor fails to operate correctly please follow the steps below for a possible solution 1 Perform the adjustments described in OPERATING THE MONITOR depending on the problem you have If the monitor does not get a picture skip to 2 2 Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists 3 If you are experiencing a problem which is not described below or you cannot correct the problem discontinue using the monitor and contact your dealer or iiyama service center for further assistance Problem D The picture does not appear The screen is not synchronized Q The screen position is not in the center The screen is too bright or too dark The screen is shaking No sound The sound is too loud or too quiet A strange noise is heard T
19. g OSD menu is displayed Adjustment Item Problem Option LOCK The POWER SWITCH is Locked POWER UNLOCK The POWER SWITCH is Unlocked LOCK The OSD menu is Locked UNLOCK The OSD menu is Unlocked TOUCH FANCTION DISABLE ON Pressing and holding of the MENU Button and the SELECT Button at the same time when the Menu is not displayed massage TOUCH DISABLE will appear on the top right corner OFF Pressing and holding of the MENU Button and the SELECT Button at the same time for about 5 seconds when the Menu is not displayed till TOUCH DISABLE disappears OPERATING THE MONITOR 13 ENGLISH Ez amp K gt AUTO ADJUST CB H POSITION V POSITION H SIZE FINE Adjustment Item Problem Option Button to Press AUTO ADJUST 99 Adjust H V POSITION H SIZE and FINE automatically H POSITION eee Too right ev V POSITION Lisa Too high Too narrow Too wide c 57 T A FINE To correct flickering text or lines V For best results use the Auto Adjust in conjunction with the adjustment pattern See page 17 for SCREEN ADJUSTMENTS See page 17 for SCREEN ADJUSTMENTS You can skip the Menu items and display an adjustment scale directly by using the following button operations AUTO ADJUST Press the SELECT Button
20. he touch Screen shows no response The touch position does not deviate Check The Power Cable is firmly seated in the socket O The Power Switch is turned ON L1 The AC socket is live Please check with another piece of equipment O If the blank screen saver is in active mode touch the keyboard or the mouse O Increase the Contrast and or Brightness The computer is ON O The Signal Cable is properly connected The signal timing of the computer is within the specification of the monitor If the monitor is in power management mode touch the keyboard or the mouse O The Signal Cable is properly connected L1 The signal timing of the computer is within the specification of the monitor O The video output level of the computer is within the specification of the monitor L1 The signal timing of the computer is within the specification of the monitor L1 The video output level of the computer is within the specification of the monitor L1 The power voltage is within the specification of the monitor O The signal timing of the computer is within the specification of the monitor The audio equipment computer etc is ON The Audio Cable is properly connected L1 The Volume is turned up O The Mute is OFF L1 The audio output level of the audio equipment is within the specification of the monitor O The audio output level of the audio equipment is within the specification of the monitor The Aud
21. io Cable is properly connected The USB Cable is firmly seated in the socket O Touch screen driver software is installed O The calibration function set up correctly TROUBLE SHOOTING 21 ENGLISH ENGLISH RECYCLING INFORMATION For better environment protection please don t dispose your monitor Please visit our web site www iiyama com recycle for monitor recycling 22 RECYCLING INFORMATION APPENDIX Design and specifications are subject to change without prior notice SPECIFICATIONS ProLite T3234MSC B1 Touch Technology Projected capacitive Screen Light transmission 909 Communication USB serial transfer system Size Category 32 LCD Panel Driving system a Si TFT Active Matrix Size Diagonal 31 5 80cm Pixel pitch 0 364mm H x 0 364mm V Brightness 350cd m Typical 315cd m with Touch panel Contrast ratio 3000 1 Typical with Touch panel Viewable angle Horizontal 178 degrees Vertical 178 degrees Typical Response time 6 5ms Gray to Gray Typical Display Colors Approx 16 7M Sync Frequency Horizontal 31 47 67 50kHz Vertical 47 63Hz Maximum Resolution 1920 x 1080 2 1 MegaPixels Input Connector VGA D sub mini 15 pin DVI D 24 pin Serial Port RS 232C In Out Plug amp Play VESA DDC2B Input Sync Signal Separate sync TTL Positive or Negative Input Video Signal Analog 0 7Vp p Standard
22. ng the screen defect please Important prepare the following information evidence Note model number If there is no fault found in the collected equipment after inspection the transferring party shall incur charges for transport and administration purchase receipt and serial number name and address for collection telephone fax number for availability during the day fenicallectonidate aatent If you have checked all of the above and there is convenient collection date date time still no picture call our information line for assistance short description of the defect in your country see the identification plate on the back of the case www iiyama com li CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC EU Directive 2004 108 EC EMC Directive 2006 95 EC Low Voltage Directive 2009 125 EC ErP Directive and 2011 65 EU ROHS Directive The electro magnetic susceptibility has been chosen at a level that gives correct operation in residential areas business and light industrial premises and small scale enterprises inside as well as outside of the buildings All places of operation are characterised by their connection to the public low voltage power supply system IIYAMA CORPORATION Wijkermeerstraat 8 2131 Hoofddorp The Netherlands We recommend recycling of used product Please contact your dealer or se
23. re or electric shock PROTECT THE CABLES Do not pull or bend the power cable and signal cable Do not place the monitor or any other heavy objects on the cables If damaged the cables may cause fire or electric shock ADVERSE WEATHER CONDITIONS It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in power may cause malfunction It is also advised not to touch the plug in these circumstances as it may cause electric shock FOR YOUR SAFETY 1 ENGLISH ENGLISH CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur or in humid dusty or smoky areas as it may cause fire electric shock or damage You should also avoid areas where the sun shines directly on the monitor DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located Please also ensure that you do not place any heavy objects on the monitor and that all cables are routed such that children may not pull the cables and possibly cause injury MAINTAIN GOOD VENTILATION Ventilation slots are provided to keep the monitor from overheating Covering the slots may cause fire To allow adequate air circulation place the monitor at least 10 cm or 4 inches from any walls Do not remove the tilt stand when operating the monitor Ventilation slots on the back of the cabinet will be blocked and the monitor may overheat if the stand is remov
24. rocess W t is preferable to adjust the image position and frequency with the monitor controls rather than the computer software or utilities W Perform adjustments after a warm up period of at least thirty minutes Additional adjustments may be required after the Auto Adjust depending on the resolution or signal timing W The Auto Adjust may not work correctly when displaying the picture other than the screen adjustment pattern In this case manual adjustments are required ENGLISH There are two ways to adjust the screen One way is automatic adjustment for H V POSITION H SIZE and FINE The other way is performing each adjustment manually Perform the Auto Adjust first when the monitor is connected to a new computer or resolution is changed If the screen has a flicker or blur or the picture does not fit in the display area after performing the Auto Adjust manual adjustments are required Both adjustments should be made by using the screen adjustment pattern Test bmp obtained via the IIYAMA web site http www iiyama com Adjust the image by following the procedure below to get the desired picture This manual explains adjustment under Windows 95 98 2000 Me XP Vista 7 CD Display the picture at the optimum resolution Enter the Test bmp screen adjustment pattern to wallpaper B Consult the appropriate documentation for doing this Test bmp is made at resolution of 1280 x 1024 Set the display position to center in the
25. rvice center Recycle information is obtained via the Internet using the address http www iiyama com You can access the Web page of different countries from there W We reserve the right to change specifications without notice W All trademarks used in this user manual are the property of their respective owners ENGLISH ENGLISH TABLE OF CONTENTS 5 1 SAFETY PRECAUTIONS te t ren deett 1 SPECIAL NOTES ON LCD 3 CUSTOMER SERVICE Tenere tette det ds 4 rre terere te or ter rra PR 4 BEFORE YOU OPERATE THE MONITOR unten 5 FEATURES citer tr e ripa ta 5 CHECKING THE CONTENTS OF THE PACKAGE 5 WALL MOUNTING CONTROLS AND CONNECTORS CONNECTING YOUR MONITOR sse 8 TOUCH SCREEN DRIVER INSTALLATION 10 GOMPUTER SETTING rece cese eere eet itp rores 11 OPERATING THE MONITOR ttt ADJUSTMENT MENU CONTENTS SGREENADJUSTMENTS toti rtp ie POWER MANAGEMENT FEATURE TROUBLE SHOOTING RECYCLING INFORMATION APPENDIX SPECIFICATIONS ProLite 234 5 1 23 SPECIFICATIONS ProLite T3234MSC B2X ProLite T3284MSC B2
26. t a bright background or in a dark room For optimal viewing comfort the monitor should be just below eye level and 40 60 cm 16 24 inches away from your eyes When using the monitor over a prolonged time a ten minute break every hour is recommended as looking at the screen continuously can cause eye strain 2 FOR YOUR SAFETY SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitors and do not indicate a problem m When you first turn on the LCD monitor the picture may not fit in the display area because of the type of computer that is used In this case adjust the picture position to the correct position W Due to the nature of the backlight the screen may flicker during initial use Turn off the Power Switch and then turn it on again to make sure the flicker disappears W You may find slightly uneven brightness on the screen depending on the desktop pattern you use W Due to the nature of the LCD screen an afterimage of the previous screen may remain after switching the image when the same image is displayed for hours In this case the screen is recovered slowly by changing the image or turning off the Power Switch for some hours W Contact your dealer or iiyama service center for the backlight replacement when the screen is dark flickering or not lighting up Never attempt to replace it by yourself Max non stop operating time and conditions 1 If a static image is displayed continuously it is recommended
27. when the Menu is not displayed 14 OPERATING THE MONITOR aT 16 I OSD H POSITION GI OSD V POSITION OSD TIMEOUT RESET 8 INPUT SELECT Adjustment Item Problem Option Button to Press OSD is too left D H POSITION OSD is right 6 7 OSD V POSITION 2 OSD is too high You can set the OSD display duration time A Ose TIMEOUT between 5 and 60 seconds lt V RESET Factory preset data is restored AUTO Select the signal input automatically INPUT SELECT VGA Select the analog input DVI Select the digital input When only one of the two signal inputs is connected to the signal source the one connected is automatically selected Input Select function is not available if there is no signal input from the selected connector or during the power management mode Available for ProLite 3234 5 2 3234 5 2 T3234MSC B3X only x m9 dU E S dl m ENGLISH ESPANOL FRAN AIS B DEUTSCH A ITALIANO Adjustment Item Problem Option Button to Press ENGLISH English ESPANOL Spanish FRAN AIS French Japanese D LANGUAGE 9S SVAG DEUTSCH German Sy Traditional Chinese ITALIANO Italian MEE Simplified Chinese OPERATING THE MONITOR 15 ENGLISH ENGLISH
28. with Touch panel Contrast ratio 3000 1 Typical with Touch panel Viewable angle Horizontal 178 degrees Vertical 178 degrees Typical Response time 6 5ms Gray to Gray Typical Display Colors Approx 16 7M Sync Frequency Horizontal 31 47 67 50kHz Vertical 47 63Hz Maximum Resolution 1920 x 1080 2 1 MegaPixels Input Connector VGA D sub mini 15 pin DVI D 24 pin Serial Port RS 232C In Out Plug amp Play VESA DDC2B Input Sync Signal Separate sync TTL Positive or Negative Input Video Signal Analog 0 7Vp p Standard 750 Positive Digital DVI Digital Visual Interface Standard Rev 1 0 compliance Input Audio Connector 0 3 5mm mini jack Stereo Input Audio Signal 1 0Vrms maximum Output Audio Connector 0 3 5mm mini jack Stereo Speakers 8W x 2 Stereo speakers Maximum Screen Size 698 4mm W x 392 8mm H 27 5 W x 15 5 H Power Source 100 240VAC 50 60Hz 1 2A Power Consumption 65W typical Power management mode 2W maximum Dimensions Net Weight 781 5 x 476 0 x 69 5mm 30 8 x 18 7 x 2 7 WxHxD 16 2kg 35 7lbs Environmental Operating Temperature 5 to 35 C 41 to 95 F Considerations Humidity 20 to 80 No condensation Storage Temperature 20 to 60 4 to 140 Humidity 10 to 90 No condensation Approvals CE T V Bauart CU IPX1 0 USB peripherals
29. zebra pattern W In case the strong flicker or blurs remain on a part of the screen repeat steps 7 because the H SIZE may not be adjusted correctly If the flicker or blurs still remain set the refresh rate of computer to low 60Hz and repeat steps from again W Adjust the H POSITION after the FINE adjustment if the horizontal position moves during the adjustment Adjust the Brightness and Color to get the desired picture after you complete the H SIZE and FINE adjustments Put back your favorite wallpaper OPERATING THE MONITOR 19 ENGLISH ENGLISH POWER MANAGEMENT FEATURE When your computer is not in use the power management feature will automatically reduce the power consumption of your monitor To use the feature the monitor needs to be connected to a VESA DPMS compliant computer There is a power management step the monitor takes as described below The power management function including any timer settings is configured by the operating system Check your operating system manual for information on how this can be configured m Power Management Mode When the H sync signal V sync signal H and V sync signals from the computer are off the monitor enters into Power Management Mode which reduces the power consumption to less than 2W The screen becomes dark From Power Management Mode the image reappears in several seconds when either the k
Download Pdf Manuals
Related Search