ADI-100 In-Car add-on DAB Receiver User Manual
Contents
1. 4 AUTOLERADS Connectors 1 SMB Connector for DAB antenna 2 3 5mm stereo audio jack for aux cable 3 Power jack for power Cable with Cigarette Lighter Plug Installation Procedure 1 Please read the installation procedure carefully prior to the actual installation Consult a professional installer if you have any issues or concerns with the installation Attention We recommend that if you are going to use the cigarette lighter as the power source for ADI 100 the lighter socket needs to connect to the ignition Otherwise you may have the following condition after the car engine is turned off ADI 100 will continue to draw minimal power from the battery For many intelligent new cars ADI 100 may be detected as device not disconnected Car radio and ADI 100 may become out of sync when you resume to listening to ADI 100 In this case please read the troubleshooting section for the solution 2 Select a location to store ADI 100 For the best performance please store it in the middle and under the car s glove compartment For other locations please store it away from metal objects and in an open area 3 Store ADI 100 with the bottom cover up and _ the cables and connectors to the back Antenna 2 H Fi To Cigarette j j Lighter CY AUTOLEADS 5 Installation Procedure continued 4 Secure ADI 100 with the supplied dual lock tapes and screws Please refer to the section on2. 2 Press the Rotary Knob or after a 3 seconds timeout to switch to the last listened station 16 AUTOLEADS FM TRANSMITTING FREQUENCY SETTINGS The FM transmitting frequency is used by ADI 100 to transmit the audio and for car radio to receive the audio The FM transmitting frequency can be changed by the following Set FM transmitting frequency in AFC mode Set FM transmitting frequency in AutoScan mode Set FM transmitting frequency manually Recall FM transmitting frequency saved in the memory Force immediate FM transmitting frequency change Set FM transmitting frequency to memory preset Fl Reset FM transmitting frequency to default 87 6MHz refer to MENU SETTINGS eer T To Display the current FM Transmitting Frequency l Press LINK and the screen will show Frequency where Frequency is the current FM Transmitting Frequency To Set FM Transmitting Frequency in AFC mode When your ADI 100 identifies a need to switch FM transmission frequency this will usually force the car radio to change FM frequency automatically in most cases and the car radio display will show AF Frequency where Frequency is the new frequency ADI 100 is transmitting Refer to To Enable AFC in the MENU SETTINGS section to enable AFC mode To Set FM Transmitting Frequency in AutoScan Mode While in the AutoScan mode ADI 100 will automatically search for three unused FM frequencies and save them into the memory in sequence from frequency 1 to
3. ADI 100 In Car add on DAB Receiver User Manual Introduction 3 Contents 4 INSTALLATION 4 OPERATIONAL CONTROLS 9 STARTING THE SYSTEM 12 USING REMOTE CONTROL KEYS 13 To Turn On or Off ADI 100 13 To Scan for the DAB Stations 13 To Listen to the DAB Stations 13 To Display Station s Information 14 To Set a DAB Preset mode 15 To Save a DAB Memory Preset 15 To Recall a DAB Memory Preset 15 To Set the Auxiliary Input mode 16 To Recall the Last Listened DAB station 16 FM TRANSMITTING FREQUENCY SETTINGS 17 To Display the current FM Transmitting Frequency 17 To Set FM Transmitting Frequency in AFC mode 17 To Set FM Transmitting Frequency in AutoScan mode 17 To Set FM Transmitting Frequency Manually 18 To Save a Desired FM Transmitting Frequency in Memory 19 To Recall FM Transmitting Frequency Saved in Memory 19 To Force Immediate FM Trasnmitting Frequency Change 20 To Set FM Transmitting Frequency Setting to Preset F1 21 MENU SETTINGS 22 To Reset FM Transmitting Frequency Setting 22 To Enable DLS DL Display 22 To Enable AFC Automatic Frequency Change 23 To Enable AutoScan 24 To Enable RC Beep Tone 25 To Set Antenna Power 25 To Perform DAB Reset 26 To Restore to Factory Settings 26 To Display Software Version 26 To Upgrade Software 27 Troubleshooting 27 Technical Specifications 29 Information on Waste Disposal 29 2 AUTOLEADS Introduction The ADI 100 is an in car audio adapter that offers a flexible and cost effective way to ap p
4. Frequency where Frequency is the new frequency that ADI 100 will set and use to transmit FM signal and force radio to tune to the same frequency automatically 2 Now you can listen to DAB stations via this new FM Frequency Note While setting a new transmit frequency operation is in process and AF Frequency is displayed other than the power key any key pressed is ignored by the system In AutoScan Mode If you notice your current listening DAB program is being interfered with you can force an immediate frequency change ADI 100 will automatically choose and set a new frequen cy but you must tune the car radio to match ADI 100 new frequency manually Do the following 20 AUTOLEARDS Operating on ADI 100 l Press and hold LINK the screen will show TO Frequency where Frequency is the new frequency that ADI 100 will set and use to transmit FM signal Operating on Car Radio l Manually change your car radio s FM frequency to match the new ADI 100 transmitting frequency setup To Set FM Transmitting Frequency Setting to Preset F1 This function allows you to set the FM transmitting frequency to the frequency saved in FM frequency preset Fl ADI 100 will change the transmitting frequency immediately l Press and hold BACK to set FM transmitting frequency to the frequency saved in FM preset F1 Note After setting the FM frequency to preset F1 You have the option to return to the default FM trans
5. after a 3 seconds timeout the system will tune to the selected Preset mode The screen will then show DONE Note When you switch to a different DAB Preset Mode the Memory Preset list of the selected DAB Preset will be loaded into the internal operating system of the ADI 100 automatically The ADI 100 will then perform all functions based on the settings of this DAB Preset Mode The system default is DAB To Save a DAB Memory Preset You can save your favorite stations in the Memory Preset List There are 4 memory presets to store 4 DAB stations in the Memory Preset List for each DAB Preset Mode 1 Rotate the Rotary Knob 4 gt to select a desired station 2 Press and hold a PX button where X is from 1 to 4 to save the current selected DAB station into Memory Preset PX of the present DAB Preset mode 3 The screen will display a short message of PX SAVED Note This new setting will overwrite a previous setting in Memory Preset X To Recall a DAB Memory Preset This function allows you to recall a favorite preset DAB station from the Memory Preset List 1 Press a PX button where X is from 1 to 4 to select the memory preset 2 If there is no DAB station saved in Memory Preset X the screen will show PX EMPTY Otherwise the screen will show station name where station name is the name of the DAB station saved in Memory Preset X AUTOLEADS 15 Note This function only recalls the
6. frequency will ensure continuous and clear reception of the DAB station to which you are currently listening 1 Press LINK and the screen will show the current FM Transmitting Frequency 2 Press a PX button where X is from 1 to 4 to select a corresponding memory preset FX and the screen will show the FM frequency saved in memory make a note of that frequency number 3 Press the Rotary Knob or after 10 seconds timeout the ADI 100 will set and transmit FM signal at this new frequency and the screen will show TO Frequency where Frequency is the frequency saved in the preset FX AUTOLEADS 19 4 Press FM preset of your car radio corresponds to the same frequency from step 2 if you have previously saved for DAB reception Otherwise tune the car radio to the same FM frequency 5 Now you can listen to DAB stations via this new FM Frequency Note While setting a new transmit frequency operation is in process and TO Frequency is displayed other than the power key any key pressed is ignored by the system To Force Immediate FM Transmitting Frequency Change This function can be used in either AFC or AutoScan mode to force a FM transmission fre quency change immediately In AFC_H or AFC_L Mode While listening to a DAB station if you hear static noise or a FM program and before AFC tunes to a clear frequency you can force an immediate frequency change by l Press and hold LINK the screen will show AF
7. screen will show the current FM Transmitting Frequency Frequency Then you can accelerate rotating the Rotary Knob 4 gt to step up or down FM frequency by 2MHZ or just rotate the Rotary Knob lt 4 gt to step up or down FM frequency by 100KHz to choose a frequency until the desired FM frequency is displayed e g 106 7MHz Make a note of that frequency number Press the Rotary Knob or after 10 seconds timeout the ADI 100 will set and transmit FM signal at this new frequency and the screen will show TO Frequency Press FM preset of your car radio corresponding to the same frequency from step 2 if you have previously saved for DAB reception Otherwise tune the car radio to the same FM frequency Now you can listen to DAB stations via this new FM Frequency Note It is recommended to set the selected FM frequency as one of the memory presets of your car radio selecting this particular preset FM frequency and together with setting the ADI 100 s FM transmitting frequency will quickly enable you fo start listening to DAB stations While setting a new transmit frequency operation is in process and TO Frequency is displayed other than the power key and key pressed is ignored by the system AUTOLEARDS To Save a Desired FM Transmitting Frequency in Memory As unused FM frequency may vary from one area to another it is suggested to save a few frequencies up to 4 frequencies in ADI 100 so that you can swi
8. the FM transmission frequency setting of ADI 100 Press LINK key the screen will show the current FM Transmitting frequency gt I cannot hear DAB program when I start up my car and turn on the car radio Check the following 1 Follow the instruction on the section STARTING UP THE SYSTEM to initialize the FM transmitting frequency on ADI 100 and the car radio 2 Make sure ADI 100 is not in the Auxiliary mode please refer to To Set the Auxiliary input mode to check and return to DAB mode gt While listening to a DAB station I lost reception suddenly and hear static noise or a FM program 1 Check if ADI 100 station information shows POOR SIG or UNAVAIL if so you may be leaving the signal coverage area please refer to To Listen to the DAB stations to select another station Also the station may be unavailable temporarily as you drive into a tunnel 2 If ADI 100 is in AFC mode the FM transmitting frequency for ADI 100 and the car radio listening Frequency maybe out of sync To reset to 87 6MHz do the following gt On your car radio press FM preset to the frequency 87 6MHz if you have previously saved for DAB reception Otherwise tune the car radio to FM frequency 87 6MHz manually AUTOLERDS Ber gt On the ADI 100 enter the menu function the screen will show 87 6MHz then press Rotary Knob to reset FM transmitting frequency to 87 6MHz or gt Press and hold BACK twice in succession to reset FM trans
9. 100 AutoScan function to au tomatically scan for 3 useable FM frequencies you will need to choose a new frequency from the scanned frequencies to set and synchronize it between the car radio and the ADI 100 manually Alternately you can use ADI 100 to set a new FM transmitting frequen cy manually or set a frequency from one of the FM transmitting frequency presets which have been previously saved and then set the car radio s FM frequency to match Note ADI 100 needs to operate with an RDS car radio in order to properly display the relevant system message of ADI 100 via the in car radio display Certification mark o e This radio is future ready because it contains digitalradio DAB FM and DAB which is a future technology a Pe standard being adopted across Europe pproved Produc AUTOLEADS 3 Contents ADI 100 Control Unit Rotary Knob Remote Control Power Cable with Cigarette Lighter CR2032 Battery Dual Lock Tapes x2 Dual Lock Tape x 1 25mm x 55mm 25mm x 35mm Screw X 2 INSTALLATION Tune in car audio system FM frequency to match with the DAB adapter to receive audio DAB adapter transmits audio via a FM frequency Install the DAB antenna to work with the DAB adapter antenna cable fiu Ooo omm ne SMB connector For the in car installation of the DAB een Connect power plug adapter refer to the user guide for detail cigarette lighter power cable to cigarette lighter
10. 6 MHz 107 9 MHz gt Mains Power 11 V 16V DE gt Input Connectors DC power jack 3 5mm stereo audio jack gt Presets 4 DAB station presets for each DAB mode and 4 FM transmit presets gt Operating Temperature Range 10 c 70 c gt Storage Temperature Range 40 c 85 c gt DAB Antenna Connector Connector Type SMB Output Voltage 12V INFORMATION ON WASTE DISPOSAL X This mark on a product and or accompanying documents indicates that when it is to be disposed of it must be treated as Waste Electrical amp Electronic Equipment WEEE Any WEEE marked waste products must not be mixed with general household waste but kept separate for the treatment recovery and recycling of the materials used For proper treatment recovery and recycling please take all WEEE marked waste to your Local Authority Civic waste site where it will be accepted free of charge If all consumers dispose of Waste Electrical amp Electronic Equipment correctly they will be helping to save valuable resources and preventing any potential negative effects upon human health and the environment of any hazardous materials that the waste may contain Note about Remote control battery There is a risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions Certification mark o e This radio is future ready because it contains digitalradio DAB FM and DAB which is a
11. ADI 100 The coiling loops of excessive power or antenna cables should start at about 10 cm away from the ADI 100 X 8 AUTOLEADS OPERATIONAL CONTROLS In Car Audio System LCD Display The ADI 100 unit is operated by using a remote controller the system messages from the remote control operation are converted to RDS text and displayed as 8 characters display on the LCD screen of your in car audio system Below is a list of ADI 100 system messages displayed on the in car audio system LCD display while operating with the remote control Messages Description DABRADIO Display after ADI 100 is powered on DAB station Display the 8 character short service name of the DAB station TUNING Indicate tuning a DAB station is in progress RESETING Indicate performing a DAB reset or factory reset is in progress DONE Confirm completion for certain system operation i e set a DAB preset mode RETUNING Indicate FM transmitting frequency is being retuned to a new frequency TO frequency Indicate ADI 100 is changing FM transmitting fre quency to a new frequency from a manual setting Other than the power key any remote control keys pressed is ignored before the change is completed AF frequency Indicate ADI 100 is changing FM transmitting fre quency to a new frequency from the AFC function Other than the power key any remote control keys pressed is ignored before the change is completed POWEROFF Display after ADI 100 is
12. Securing ADI 100 Step by Step 5 Minimize coiling loops of excessive power cable and antenna cable and do not secure them on ADI 100 Please refer to section on Installation do and don t Attention Anytime you need to disconnect connect the antenna from ADI 100 please unplug ADI 100 from the cigarette lighter first to avoid possible damage to the antenna Damage resulted from incorrect installation of the antenna is not covered by the warranty 6 Plug one end of the power cable to ADI 100 and the cigarette lighter plug into car s cigarette lighter There is a lock mechanism on the plug of Power Cable to ADI 100 First plug the power cable into the 12V DC jack 1 and then you need to turn the power plug 90 degree clockwise 2 as illustrated below This is to ensure that the power cable will be firmly connected to the ADI 100 at all time 7 Start using ADI 100 with the remote O o Lal 4 control please refer to the sections AERIAL AUKN on OPERATION CONTROLS and _ 12VD a STARTING UP THE SYSTEM 6 AUTOLEARDS Securing ADI 100 Step by Step To secure ADI 100 on a chosen store location using the supplied dual lock tapes and or screws do the following 1 Locate the positions on the back of ADI 100 and the chosen mounting location e g in the middle and under the car s glove compartment where you want to apply the dual lock tapes __ Secure with 2 Clean both surfaces with alcohol if avaia
13. ble and wipe dry before you start Affix the tape on the ADI 100 and the chose mounting location 3 Remove one side of the backing from each of the two pieces of dual lock tapes and adhere the tapes onto the back of ADI 100 on the marked positions in 1 4 Remove the other side of the backing and adhere ADI 100 to the chosen store location with ADI 100 s cables and connectors to the back 5 Carefully remove ADI 100 from the store location with dual lock tapes separated so that ADI 100 and store location each has 2 half pieces of the tapes screw 6 Apply the pressure evenly to all 4 half pieces on ADI 100 and the store location so that the tapes adhere to both surfaces securely 7 Wait 8 hours and then adhere ADI 100 to the mounting location by joining the 4 half pieces of the tapes together 8 Alternatively or in addition secure ADI 100 with the supplied screws Installation Do s amp Don t s As ADI 100 has internal antenna and FM Transmitter it is important to avoid signal interference from excessive cable coiling The next page illustrates the do s and don t when coiling and storing ADI 100 s excessive antenna cable and power cable AUTOLEADS T Installation Do s amp Don t s continued l Do not tangle the antenna and power cables together gt 2 Minimize coiling loops of excessive power cable or antenna cable and do not secure them on or besides
14. changed too often and set AFC_H mode if you often hear static noise and the FM frequency is not changed By default ADI 100 is already set to use AFC_H mode however if you want to change or return to AFC mode do the following Setting on ADI 100 1 In the menu function rotate the Rotary Knob 4 gt until the screen shows LINKMODE 2 Press the Rotary Knob and then rotate the Rotary Knob 4 gt until the screen shows AFC_H or AFC_L 3 Press the Rotary Knob the AFC function is now enabled and the ADI 100 is operating in the AFC mode Setting on Car Radio 1 Enable the Alternative Frequency feature of your car radio Consult your car radio manual or the car dealer if your car radio has the AF feature and how to enable AF feature Note If your car radio does not have AF feature the AFC function must not be enabled and refer to To Enable AutoScan If the AF feature of your car radio and ADI 100 s AFC function are not compatible the AFC function must not be enabled instead refer to To Enable AutoScan The system default is AFC_H mode enabled If you hear static noise or a FM program and before AFC tunes to a clear frequency you can force an immediate frequency change manually refer to the procedure outlined in the TROUBLESHOOTING section for detail While in AFC mode if the FM transmitting frequency for ADI 100 and the car radio listening frequency is out of sync and you wish to reset them re
15. d then rotate the Rotary Knob 4 gt until the screen shows AUTOSCAN 3 Press the Rotary Knob the function of AutoScan is now enabled and the ADI 100 is operating in the AutoScan mode Note Switching to the AutoScan mode does not change the current FM transmitting frequency as it remains the same as before the switch Switching to the AutoScan mode it disables the AFC function 94 GUCE To Enable RC Beep Tone When you enable RC beep tone ADI 100 will resoond with a beep tone each time an operation is performed on the remote control l In the menu function rotate the Rotary Knob 4 gt until the screen shows RC BEEP 2 Press the Rotary Knob to enter RC beep tone selection operation 3 Then you can rotate the Rotary Knob 4 gt until the screen shows BEEP ON to enable the RC beep tone 4 Or you can rotate the Rotary Knob 4 gt until the screen shows BEEP OFF to disable the RC beep tone 5 Finally press the Rotary Knob to set the RC beep tone screen will then show DONE Note The default setting is OFF To Set Antenna Power For ADI 100 to work with an active antenna the antenna power must be set to ON ADI 100 can also work with a passive antenna l In the menu function rotate the Rotary Knob 4 gt until the screen shows ANTENNA 2 Press the Rotary Knob to enter Antenna Power selection operation 3 Then you can rotate the Rotary K
16. e DLS DL display on radio 4 Or you can rotate the Rotary Knob 4 gt until the screen shows OFF to disable the DLS DL display on radio 5 Finally press the Rotary Knob to set the DLS DL display The screen will then show DONE Note The default DLS DL setting is ON 2 gt Gb eRe To Enable AFC Automatic Frequency Change If your car radio does not have AF feature then please refer to To Enable AutoScan It may become necessary to change the FM transmitting frequency as you drive into an area where the FM frequency transmitted by ADI 100 is used by an FM broadcaster ADI 100 has an AFC function that allows you to continuously listen to DAB programs through your car radio system without the need to change the FM frequency manually Subject to car radio compatibility To perform this AFC function your car radio must have AF Alternative Frequency feature and the AF fea ture of your car radio must be activated When the AFC function of ADI 100 is enabled and the AF feature of your car radio is activated your car radio will tune to an unused FM frequency automatically when you drive into an area where the original FM frequency for DAB is no longer available Furthermore there are two AFC modes AFC_H High Sensitive amp AFC_L Low Sensitive While in AFC mode ADI 100 will detect and determine if a frequency change is necessary constantly Set AFC_L mode if you experience the FM frequency is being
17. ently located Stations found as a result of the search are added to the station list in the alphabetical order To scan for the DAB stations do the following l Press the Rotary Knob then SCAN to do a full scan of DAB stations the screen will show SCANNING Note Each time you start ADI 100 if the station list is empty it will perform a Full Scan of DAB stations automatically You may also need to perform a Scan function if you drive your car to a new area where the broadcasting DAB stations are not on the current station list While the Scan operation is in process you can press the Rotary Knob at any time to stop Scan function and revert to listening to the currently selected station If the DAB Station List is not empty before scanning then after completion of DAB Scan the ADI 100 will revert fo playing the last DAB station automatically If the DAB Station List is empty before scanning the ADI 100 will tune in the first station of the new DAB Station List resulted from this DAB Scan If the DAB Station List is empty before scanning and there is no station detected by DAB Scan the screen will show EMPTY There are no DAB stations available in the area where you performed DAB Scan function To Listen to the DAB Stations There are two options available for you to select and listen to a DAB station Quick Tune and Step Tune Step Tune is used when you want to step through the list of stations one by one and in al
18. fer to the procedure outlined in the TROUBLESHOOTING section for detail AUTOLEADS 23 Attention The ADI 100 comes with the AFC function In order to use this function your car radio must have AF alternative frequency feature and AF must be enabled Please consult your car radio manual or the car dealer for these requirements before using this function While working with the AFC function the possible factors that could affect its normal operation are I The FM sensitivity varies among car radios and the sensitivity can affect AFC s performance 2 The algorithm implemented in each car radio s AF feature varies and this can affect radio s FM frequency tuning when triggered by AFC If AFC function is unable to function normally please disable AFC and use AutoScan mode instead Refer to the next section To enable AutoScan To Enable AutoScan If your car radio does not have AF feature then you must not enable AFC However you can use AutoScan to automatically search for unused FM frequency for transmitting When this function is activated the ADI 100 will keep searching available FM frequencies and display these frequencies whenever you need You may select one of them as the new transmitting frequency and tune your car radio in this new FM frequency to receive DAB services Continuously l In the menu function rotate the Rotary Knob 4 gt until the screen shows LINKMODE 2 Press the Rotary Knob an
19. frequency 3 When you are using ADI 100 to listen to a DAB service and experience constant interference from other source which means that you are driving into an area where the present FM frequency is used by an FM broadcaster When this happens you need to find an unused FM frequency for transmitting the DAB service to your car radio Refer to To Enable AutoScan in the MENU SETTINGS section to enable AutoScan mode The enabled AutoScan feature can help you to do FM frequency change quickly by the following steps Operating on ADI 100 l Press LINK and the screen will show the current FM Transmitting Frequency 2 Keep pressing LINK and it will go thru from frequency 1 to frequency 3 for each time your press and the display will show SX Frequency where X ranges from 1 to 3 and Frequency is the auto scanned frequency Stay at the frequency you prefer which will be the new FM frequency for transmitting AUTOLEARDS 17 3 Press the Rotary Knob or after a 10 seconds timeout the FM transmitter will set and transmit FM signal at the new frequency Now you can listen to DAB stations via this FM frequency Operating on Car Radio 1 Manually change your car radio s FM frequency to match the new ADI 100 transmitting frequency setup To set FM Transmitting Frequency Manually If you wish to change the setting and use your own selected FM transmitting frequency manually do the following 1 2 18 Press LINK and the
20. future technology a EEE standard being adopted across Europe pproved Produc AUTOLEADS 29 30 GbR AUTOLEADS 31 AUTOLEADS Autoleads is a brand of Armour Automotive Unit 25 Woolmer Way Bordon GU35 9QZ 44 0 1420 476767 info armourauto com www autoleads co uk www armourauto com e o pny This radio is future ready because it contains digitalradio DAB FM and DAB which is a future technology standard being adopted across Europ Approved Product
21. l while the screen is showing NO 3 1 The screen will show RESETING to indicate that factory reset is iN progress 3 2 The system will perform a scan of DAB stations automatically after the factory reset is completed You must switch the car radio to FM 87 6MHz to continue DAB listening Note Factory reset will erase all previous system s settings and set them to default To Display Software Version This function allows you to display the current software version of your ADI 100 l In the menu function rotate the Rotary Knob 4 gt until the screen shows VERSION 2 Press the Rotary Knob to display the software version the screen will show the current software version number x x x x 26 AUTOLERADS To Upgrade Software This function is used by the maintenance personnel only to upgrade the existing ADI 100 module software to a new version TROUBLESHOOTING Please read this user manual carefully before using the ADI 100 In Car DAB Adapter If you still have difficulties to use this unit this section gives some of the most likely solutions to the problems you might have gt I cannot find any DAB stations Ensure that DAB coverage exists in your area Please visit www worlddab org or www digitalradionow com to check for DAB coverage gt I can find DAB stations but I cannot get any sound Make sure that the car radio is not mute check the volume settings of the car radio gt I forget
22. ll memory preset P3 Press and Hold gt Program memory preset P3 while listening to a DAB station Function DAB gt Set ADI 100 to one of the 3 DAB preset modes to listen to DAB Press gt Recall memory preset P4 Press and Hold gt Program memory preset P4 while listening to a DAB station Function MENU 87 6MHz Default FM transmitting Frequency RADIOTXT enable disable display of DLS DL information from the station LINKMODE select operating mode AFC_H AFC_L AutoScan RC BEEP enable disable beep tone in response to remote control operation ANTENNA set ON for a certified active DAB antenna set OFF for all other antennas DABRESET erase the station list but keep the memory presets for all DAB Presets and then perform a full scan of DAB stations automatically after the DAB has reset FACTORY return all system settings to defaults UPGRADE upgrade the module software to a new version VERSION display the current software version gt gt gt gt gt gt Press gt Display adaptor s current FM transmitting frequency gt Select and set the FM transmitting frequency from a manual setting or from one of the four memory presets gt Save the FM transmitting frequency setting to one of the four memory presets gt In AutoScan mode select and set the FM transmitting frequency from one of the three AutoScan frequencies Press and Hold gt Perform an immediate FM transmitting frequenc
23. ly modern digital audio technology to your existing analogue in car audio system The existing analogue system can be easily upgraded to receive DAB DAB digital radio services ADI 100 uses FM RDS micro transmitter and no complex cabling to your car au dio system The ADI 100 DAB receiver is operated using a remote controller while all mes sages related to the system s operations such as service name memory preset etc are converted to RDS text and displayed on the LCD screen of your in car audio system The flexible configuration options of the ADI 100 makes it easy to install in different car makes and models Furthermore ADI 100 has an AFC Automatic Frequency Change function that allows you to continuously listen to your favorite DAB programs through your car radio system without the need to frequently change the FM frequency manually when you drive into a metropolitan area where FM stations are highly crowded Without AFC the manual frequency change can be hazardous and inconvenient as the driver will have to find an unused FM frequency by tuning the car radio change FM transmitter to use the same unused frequency and repeat the process each time the FM transmit frequency is inter fered by an FM station Consult your car radio manual or the car dealer if your car radio has AF alternative frequency function and how to enable AF function before using this AFC function If AF function is not built in your car radio you can use ADI
24. mitting frequency to 87 6MHz To Reset to a frequency that has been saved in FM frequency preset 1 do the following gt On your Car Radio press the FM preset of your car radio that corresponds to the same frequency as in ADI 100 s FM frequency preset 1 if you have previously saved for DAB reception Otherwise tune the car radio to that FM frequency manually gt On your ADI 100 press and hold BACK to reset FM transmitting frequency to FM frequency preset 1 3 If ADI 100 is in AutoScan mode the FM channel you selected for DAB mode may be occupied by an existing radio station You need to change the frequency settings of FM Transmitter Please refer To enable AutoScan to set a suitable new frequency gt If you hear static noise or a FM program and before AFC tunes to a clear frequency you can force an immediate frequency change manually by one of the following Refer to FM Transmitting Frequency Settings section Set FM transmitting frequency manually Recall FM transmitting frequency saved in the memory Force immediate FM transmitting frequency change Set FM transmitting frequency to memory preset Fl ie Refer to MENU SETTINGS section 5 Reset FM transmitting frequency to default 87 6MHz 28 AUTOLEARDS TECHNICAL SPECIFICATIONS gt Digital Audio Services DAB DAB gt RF Frequency Range DAB Band Ill 174 MHz 240 MHz gt RF Sensitivity for DAB Band Ill 98dBm 100dBm gt FM Transmit Range 87
25. mitting frequency 87 6MHz by within 30 seconds after step 1 press and hold BACK again AUTOLEADS Bee MENU SETTINGS You must press the Rotary Knob then MENU button to enter the menu function rotate the Rotary Knob 4 gt to select a menu setting and then press the Rotary Knob to confirm the selection To Reset FM Transmitting Frequency Setting This function allows you to reset the FM transmitting frequency to the default setting FM 87 6MHz 1 Reset ADI 100 s FM transmitting frequency by either way below q Enter the menu function the screen will show 87 6MHz Then Press the Rotary Knob to reset FM transmitting frequency to 87 6MHz b Press and hold BACK twice in succession to reset FM transmitting frequency to 87 6MHz 2 Press FM preset of your car radio to the frequency 87 6MHz if you have previously saved for DAB reception Otherwise tune the car radio to FM frequency 87 6MHz manually To Enable DLS DL Display When you enable DLS DL Display the radio will show DLS information such as song titles music types and news or traffic updates from the station if DLS is being received or DL information song track song artist if DL is being received l In the menu function rotate the Rotary Knob 4 gt until the screen shows RADIOTXT 2 Press the Rotary Knob to enter radio text selection operation 3 Then you can rotate the Rotary Knob 4 gt until the screen shows ON to enable th
26. ning station this informa tion can be displayed thru repeatedly pressing the Rotary Knob key l Each time you press the Rotary Knob while listening to a DAB station the screen will cycle through station s information below station name where station name is name of the DAB station DLS DL info when DLS DL is enabled thru menu settings it displays real time Dynamic Label Segment DLS station information such as song titles music type and news or traffic updates or Dynamic Label Plus DL extended information for song track and song artist SIG xx where xx is the signal quality value Note The default DLS DL setting is ON If the feature is OFF the screen will show TEXT OFF 14 GU CEHE To set a DAB Preset Mode The ADI 100 provides individual memory settings for up to three sets of DAB Preset Modes DAB1 DAB2 and DAB3 Each DAB Preset Mode has its own Memory Presets of DAB stations please refer to To Save a DAB Memory Preset and To Recall a DAB Memory Preset sections below This allows user to setup three DAB Presets for different users driver or passengers or different group of stations to enjoy the favorite programs based on the individual settings l Press the Rotary Knob and then DAB to enter the DAB Preset selection mode function the screen will display the current DAB preset mode 2 Rotate the Rotary Knob 4 gt to select a particular DAB Preset Mode 3 Press the Rotary Knob or
27. nob 4 gt until the screen shows ANT ON to set the Antenna Power On 4 Or you can rotate the Rotary Knob 4 gt until the screen shows ANT OFF to set the Antenna Power Off 5 Finally press the Rotary Knob to set the Antenna Power Note The default Antenna Power setting is ON AUTOLEADS 25 To Perform DAB Reset 1 In the menu function rotate the Rotary Knob 4 gt until the screen shows DABRESET 2 Press the Rotary Knob to perform a reset operation for DAB Presets 3 If you do want to reset rotate the Rotary Knob 4 gt to find YES and then press the Rotary Knob for confirmation Otherwise you can press the Rotary Knob to cancel while the screen is showing NO The screen will show RESETING to indicate that DAB reset is in progress DAB reset will erase the station list but keep the memory presets for all DAB Presets and then perform a full scan of DAB stations automatically after the DAB has reset It does not erase the current FM transmitting frequency and all FM transmitting frequency presets To Restore to Factory Settings le In the menu function rotate the Rotary Knob 4 gt until the screen shows FACTORY 2 Press the Rotary Knob to perform a factory reset operation 3 If you do want to reset rotate the Rotary Knob 4 gt to find YES and then press the Rotary Knob for confirmation Otherwise you can press the Rotary Knob to cance
28. phabetical order Quick Tune allows you to move more quickly through the list of stations by advancing to the first station in the previous next alphabet character in the station list Once you have reached the desired initial alohabet character you can then use Step Tune to refine move to the desired station AUTOLEADS 13 Step Tune l Rotate the Rotary Knob 4 gt to step through the stations one by one until the screen shows the desired station station name ADI 100 will start tuning to the selected station immediately Quick Tune l Accelerate Rotating the Rotary Knob 4 gt to quickly tune to the first station in the previous next alohabet Repeat the action one alphabet at a time until the screen shows the DAB station with desired initial alphabet 2 Perform the Step Tune to step thru the stations one by one until the screen shows the desired station station name ADI 100 will start tuning to the selected station immediately Note When the DAB station you have selected is not available the screen will show UNAVAIL There will be no audio output from the ADI 100 When the signal strength of the DAB station you have selected is too weak the screen will show POOR SIG Each time you start ADI 100 if the channel list is empty it will perform a Full Scan of DAB stations automatically To Display Station s information The ADI 100 provides certain information about the current liste
29. r the menu function 7 2 Rotate the Rotary Knob 4 gt until the screen shows LINKMODE 7 3 Press the Rotary Knob and then rotate the Rotary Knob 4 until the screen shows AUTOSCAN 7 4 Press the Rotary Knob the function of AutoScan is now enabled and the ADI 100 is operating in the AutoScan mode Listen to the DAB stations Please refer to USING REMOTE CONTROL KEYS section for the system operation While you are using AutoScan function and you are experiencing noise on the listening DAB station please refer to To Set FM Transmitting Frequency in AutoScan Mode to select a auto scanned FM frequency or To Set FM Transmitting Frequency Manually to manually switch to another FM frequency To avoid unnecessary draining of the car battery when ADI 100 is idle after 4 hours of idling from the user s last action ADI 100 will be automatically turned off While in the standby mode press the Rotary Knob to return ADI 100 back to the operating mode AUTOLERADS USING REMOTE CONTROL KEYS The ADI 100 operating mode can be turned off or turned on by the following 1 Press and hold the Rotary Knob to turn it off while ADI 100 is in the operating mode 2 Press the Rotary Knob to return it to the operating mode while ADI 100 is off To Scan for the DAB Stations This function searches for all DAB stations in Band Ill from channel frequency 5A to channel frequency 13F that are available in the area where your car is pres
30. stations saved in the Memory Preset List of the particular DAB Preset Mode please refer to To Set a DAB Preset Mode section To Set the Auxiliary Input mode The ADI 100 provides the capability to play audio device such as MP3 or iPod etc through your car radio l Press the Rotary Knob then AUX to set the listening mode to auxiliary input mode and start listening to the audio device The screen will then show DONE and then AUXMODE Note While in Auxiliary Inout mode to listen to the last listened DAB station you must press the Rotary Knob and then press DAB to tune to the last listened DAB station and return to the DAB preset mode that was last listened to While in Auxiliary Inout mode to recall a preset DAB station you must press a PX button directly where X is from 1 to 4 to return to the DAB preset mode that was last listened to and tune to the DAB station saved in the memory preset PX If the memory preset PX pressed is empty then ADI 100 will tune to the last listened DAB station instead To Recall the Last Listened DAB Station The ADI 100 automatically remembers the station that is last listened to This allows you to go back to last listened DAB station quickly even it is not in the Memory Preset List l Press BACK to recall the station that was most recently listened to The screen will show LS EMPTY if the last listened station has not memorized a station name yet or station name if it has
31. tch to a new FM transmitting frequency instantly when you drive into an area where the original FM frequency for DAB is no longer available l Press LINK and the screen will show the current FM Transmitting Frequency Frequency 2 Then you can rotate the Rotary Knob 4 gt to step up or down FM frequency by 100KHz to choose a frequency and the screen will show Frequency where Frequency is the chosen frequency 3 Press and hold a PX button where X is from 1 to 4 to save the current selected FM frequency into the corresponding preset memory FX 4 The screen will display a short message of FX SAVED Note The default FM frequencies saved in presets FI to F4 are 87 6MHz 92 5MHz 102 5MHz and 107 9MHz respectively It is suggested to set those FM frequencies saved in ADI 100 into FM preset of your car radio Selecting the FM preset of your car radio and the matching FM preset of ADI 100 will switch the FM transmission frequency instantly for a clear reception of the DAB station Saving the frequency in memory does not affect the current FM transmitting frequency it remains the same as before saving the frequency To Recall FM Transmitting Frequency Saved in Memory You may drive into an area where the FM frequency transmitted by ADI 100 is used by an FM broadcaster When this happens your reception of DAB station will be getting worse with increasing interference from another FM program Switch to a free FM
32. turned off into the standby mode RC LOW Indicate remote control s battery is low battery change is due AUTOLEADS 9 Remote Control Please refer to next sections USING REMOTE CONTROL KEYS MENU SETTINGS and FM TRANSMITTING FREQUENCY SETTINGS for detail description of each operation Control Key Rotary Knob 10 AUTOLEARDS General Operation Press Turn on ADI 100 while it is off gt Confirm a selection Change station information while listening to a DAB station gt Press and followed by AUX DAB SCAN or MENU to enter the selected function mode Press and Hold gt Turn off ADI 100 while it is on Rotate lt 4 gt Step tune to select a DAB station gt Navigate to items sub items and settings after MENU is pressed gt Adjust FM transmitting frequency by 100 KHz after LINK is pressed Accelerate Rotation lt 44 gt gt Quick tune to select a DAB station gt Adjust FM transmitting frequency by 2MHz after LINK is pressed Press gt Recall memory preset P1 Press and Hold gt Program memory preset P1 while listening to a DAB station Function AUX Set ADI 100 to AUX mode to listen to an external audio source Control Key P2 SCAN General Operation Press gt Recall memory preset P2 Press and Hold gt Program memory preset P2 while listening to a DAB station Function SCAN gt Perform a full scan for DAB stations Press gt Reca
33. y change Press gt Recall the last listened DAB station Press and Hold gt Reset FM transmitting frequency to the frequency saved in FM preset 1 Within 30 seconds press and hold again to return the frequency to 87 6MHz AUTOLEFDS 11 STARTING UP THE SYSTEM 1 2 ao 12 Turn on your in car audio system Enable the AF function on your car radio if it is equipped Consult your car radio manual or the car dealer if your car radio has AF feature and how to enable AF feature Tune the car radio s FM frequency to FM 87 6MHz which is the same as ADI 100 default FM TX frequency Start ADI 100 by plugging the cigarette lighter power plug into the cigarette lighter the audio system display will show DABRADIO ADI 100 will perform a Scan of DAB stations automatically If FM 87 6MHz is already used by a FM broadcaster or the station is noisy change the initial FM TX frequency as below Operating on ADI 100 gt Press and hold LINK for 3 seconds ADI 100 will set a new and clear frequency to transmit the FM signal Operating on Car Radio gt Use auto scan function of your car radio to search for an FM broadcast having program service name DABRADIO Stay tuned on this FM frequency your ADI 100 and car radio are now synchronised If your car radio does not have AF feature do the following to change ADI 100 s FMTX mode to AutoScan instead of the default AFC 7 1 Press the Rotary Knob and then MENU to ente
Download Pdf Manuals
Related Search