Home
Installation manual: CA-1803BT “Athos”
Contents
1. Self location disabled Bold marked values factory default Bold marked values factory default Steps to enroll RC 8x controllers Steps to enroll detectors 1 The car alarm should be disarmed with the ignition on 1 The car alarm should be disarmed ignition on 2 Send the SMS instruction MASTER LEARN RC 2 To enroll the internal detectors send the SMS command MASTER LEARN 3 The car alarm beeps 3 times and an LED starts to flash INT To enroll the external detectors send the SMS command MASTER F LEARN EXT 4 The RC 8x controller is enrolled by pressing buttons 8 and 3 The car alarm beeps 3 times and an LED starts to flash simultaneously for approx 3 sec A siren chirp confirms the enrollment By 4 You can enroll a new detector to the system by inserting its batteries If enrolling the first remote control all other remote controls previously enrolled you enroll a first detector you will erase all detectors from the will be erased so enroll all the controllers intended for use one by one associated groups enroll all of them which will be used in the group in 5 Exit enrollment by turning the ignition off The alarm confirms the enrollment by sequence sending an SMS message to authorized phones TEL1 to TEL4 5 Exit enrollment by turning the ignition off The alarm confirms enrollment by sending an SMS message to authorized phones TEL1 to TEL4 GSM car alarm CA 1803BT Athos 1 6 MHF58202 Functions r
2. are both disabled 1 10 ms siren chirps when arming disarming non backed up siren 1 open door signalling and INP activation while arming are both 2 3 4 9 siren chirps when arming disarming a siren of another enabled type lasting 20 30 40 50 100 200 300 or 500 ms 2 INP activation while arming enabled open door signalling enabled with Silent alarm Audible alarm a 10 second delay SMS alarm report and siren sound 3 INP activation while arming enabled open door signalling disabled phone call Voltage detector disabled Voltage drop detector enabled SMS remote control not SMS remote control instructions lock unlock signal duration Reset 1 confirmed by SMS reply confirmed by SMS reply 0 0 5 0 5 sec suitable for electromagnetic locks 0 arming control by dialling in disabled 1 4 4 sec suitable for pneumatic locks 1 arming control by dialling from TEL1 enabled 2 60 0 5 sec suitable for automatic window closing 2 arming control by dialling from TEL1 and TEL2 enabled DOOR input logic 3 arming control by dialling from TEL1 TEL2 and TEL3 enabled 1 activated by falling edge grounding 4 arming control by dialling from all TEL1 to TEL4 enabled 2 activated by rising edge disconnecting from GND Arming control by dialling in see E INP1 logic Arming control by dialling is _ 1 activated by falling edge grounding in is not confirmed by confirmed by SMS to the phone 2 activated by rising edge disconnecting fro
3. Installation manual CA 1803BT Athos Before installation The car alarm should only be installed by a professional installer It is suitable for ie cars with a dashboard voltage supply of 12V or 24V with a negative ground This is the basic version of the installation manual and programming sequences On connection During the first power up the value of supply voltage is read and the the web site wwwjablotronalarms com in the download section you can find a full inputs are set to default settings The alarm is designed to be installed inside the car version of this manual or you can find it included in the installation kit on CD DVD If you have no experience with CA 1803 installation we recommend you to read the extended version of the manual to know all the parameters well The immobilizer relay contact of car alarm is connected only in disarmed mode and if the ignition is on Do not block circuits that are under voltage while the ignition is off It could cause a serious damage of the vehicle For cars with a voltage supply of 24V the following restrictions apply to car alarm installation 1 It is not possible to connect a hands free set of type HF 03 2 When used for acoustic signalling the SIR output is switched to the power supply voltage Consequently this output switches to 24V so it is necessary to use a siren of type SA 606 24V instead of the SA 530 which is supplied in the standard package In this case it is
4. elated to GPS Location detection using GPS An example of an instruction sent from an authorized phone GPS An example of response Car alarm reports Location GMT 3 12 10 35 50 43 495N 15 1 1 253E 515 50 Time 3 12 05 11 35 GMT 3 12 10 35 Greenwich Mean Time mean meridian 50 43 495N 15 11 253E latitude and longitude 515 altitude approximated 50 current velocity Time 3 12 05 11 35 current local time Time zone setting To adjust the time information to local time time zone setting is possible The car alarm adds subtracts the time shift expressed in hours to the GMT time for middle Europe 2 hours in summer time 1 hour in winter time Instruction MASTER TIME xy xy is the time shift in hours 3 2 1 2 relative to GMT MASTER TIME GSM turns on automatic setting via incoming SMS Integrated Bluetooth module BT When disarmed and with the ignition key on the car alarm sends GPS coordinates via the BT which can be used for navigation The car alarm authorization code for device pairing is 0000 The ignition key must be on during the pairing process Internet remote access The web site www GSMLink cz enables car alarm remote control to users and setting to installers To get internet access to an installed and powered car alarm you will first be asked to register your car alarm on the first page You will find a unique registration code for your car alarm on the warranty card Additional features P
5. ettings information about the quality of the GSM signal the registration code for GSMLink devices and some other parameters This command always requires the Master code Example of instruction MASTER DINFO Example of response Car alarm reports CA 1803A SN 123456 SV 01 LV 03 RK ABCDE 12345 FG67 R 01 GSM 25 GPS 5 Time 3 2 06 11 35 CA 1803 gt CA 1803A car alarm version SN 123456 identification number of the product SV 01 software version LV 03 language version RK ABCDE 12345 FG67 registration code for GSMLink R 01 current Reset mode of the device GSM 25 instant quality of GSM signal ranging from 0 to 32 best GPS 5 number of visible satelites 0 16 Specification Power supply Stand by consumption Immobilization 12 24V DC 8 32V max 20 mA 8A permanently 12A intermittently Complies with ECE Regulation No 97 00 Can be operated according to ERC DEC98 20 21 ERC REC 70 03 Safety EN 60950 1 EMC EN 55022 EN 50130 4 Radio interference ETSI EN 301 419 1 EN 301 511 ETSI EN 300 220 ETSI EN 300 328 97 RAI 01 4532 compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC and 1995 56 EC The original of the conformity assessment can be found at www jablotron com Technical Support section C 4 JABLOTRON ALARMS a s hereby declares that the CA 1803BT is in Note Although this product does not contain any harmful materials we suggest you return the product to the deale
6. m GND SMS which called the car alarm INP2 logic User can not change SMS User can change SMS texts by TXT 0 activated by falling edge grounding it triggers an alarm also if Texts Sequence disarmed 24 hour reaction If the car is not entered within 1 1 activated by falling edge grounding REARM disabled minute after disarming it will REARM 2 activated by rising edge disconnecting from GND 0 Immobilization by arming and by SMS instruction Central locking input logic Reset 2 1 Immobilization by arming and automatically 5 minutes after 1 activated by falling edge grounding ignition is turned off AUTOIMO and also by SMS instruction 2 activated by rising edge disconnecting from GND ee aan 0 corfimaton by tum ghis for disarming i needed eset ignition is turned off for more than 60 minutes the SMS STATUS is era by turn lights for armmg and disarmirigis sent as an alert to possible Tester STO ib by SMS 2 confirmation by turn lights for arming and disarming is not e Cals ration Will be sent Dy needed so INP1 can be used as an alarm input after an IMO instruction has been Wh itoring of s performed en armed no monitoring o GPS location changes are or if the car stops after an GPS location changes monitored when armed 0 AUX output is a bus for communication with CR 11A modules immobilization SMS instruction 1 AUX output provides power for external sensors SMS alarm report only
7. necessary to set the confirmation beeps to 100 ms Configuration table RESET EN 1 MASTER RESET EN 1 Mode setting RESET 1 alarm has its own remote control and provides signals for central locking After which the RESET 2 alarm is operated by an original remote controller for central locking RESET 3 GSM entry is erased pager for cars with an installed car alarm Performing the RESET instruction is indicated by 4 beeps from the SIM Consequently all settings enrolled remote controllers and wireless detectors will be erased Not applicable MASTER UC uuuu User code setting the code allows you to operate the alarm remotely via SMS from unauthorized phones uuuu is a new user code 4 to 8 letters A Z amp 0 9 case insensitive Factory default user code is USER Not applicable MASTER MC xxxx Master code setting xxxx is a new master code A Z amp 0 9 case insensitive The code allows you to change the maintenance settings for the car alarm Factory default master code is MASTER MASTER TELn xx x Setting of phone numbers to report alarms to n 1 to 4 DIALn xx x MASTER DIALn xx x Setting the phone numbers to dial using Hands free n A B 1 2 DIP abcdefghij MASTER DIP abcdefghij DIP parameter entry see the DIP table SET abcdefghij MASTER SET abcdefghij SET parameter entry see the SET table DIP parameters SET parameters ee aa 22 ee a 0 silent an without siren 0 open door a and INP activation while arming
8. r or directly to the producer after use a 7 NN SEDic max 4x RC 8x AUX AIS ee crc tilt detector Backup battery 2x brown Immobilization max 12A a yellow pp o2 l lI _ Siren 2 Fuse 5A gt 12 24V Door switches S Battery 2 A p_INP1 alarm input JABLOTRON 2 S CREATING ALARMS iif tei white blue UNLOCK JABLOTRON ALARMS a s 3 central Pod Skalkou 4567 33 _NP2 alarm input F white biack LOCK locking 46601 Jablonec nad Nisou 24 hour reaction Czech Republic alls Tel 420 483 559 911 o Ignition key 15 l 5 Fax 420 483 559 993 Internet www jablotron com GSM car alarm CA 1803BT Athos MHF58202
9. re paid SIM card balance It is recommended not to use prepaid cards in the car alarm If you have no other choice than prepaid cards you can enable the CREDIT instruction by the following sequence MASTER CREDIT uuu u xx yyy zz where uuu u is the provider s code to obtain the balance XX is the time period in days for regular checking yyy is the threshold level below which the balance is reported to the user TEL1 zz is the position of the first digit of the balance in the reply SMS from the provider q JA wireless detectors O 0 JA 85P JA 85B movement glass break RESET 1 sm k A button to release the SIM card e _ aoe HF connector for Handsfree GSM antenna e After this sequence has been sent once the car alarm will check the balance automatically every xx days and if the balance is lower than yyy the user will be notified TEL1 e If the CREDIT instruction is enabled in the above way the user can also obtain the current balance by the instruction CREDIT e To disable the automatic balance checking set the time period xx to 00 Reset GSM If you need to disconnect and then reconnect the GSM module to the GSM network then use the command MASTER RESET GSM This does not affect any settings and is typically used for GPRS activation or charging up credit This command always requires the Master code Service instruction The DINFO instruction allows you to obtain current s
Download Pdf Manuals
Related Search
Related Contents
Manual - Northern Tool + Equipment Vol.120 - 公益社団法人 全国家庭電気製品 公正取引協議会 SensAlert ASI HART card Manual Téléchargez - Canadian Tire I25 Imprimacion Aguapox Canon PIXMA MX435 Brochure Ergotron TM Cart 32 Copyright © All rights reserved.
Failed to retrieve file