SP9 - User's Manual
Contents
1. Factory setting of access code is 1234 EVENT level change in case of digital input zone change in case of analog inputs SP9 can react on EVENTS by several ACTIONS if it is setup this way SP9 can send SMS messages on selected phone numbers and or to make voice calls on selected phone numbers ACTION one voice call or one SMS to one user Any EVENT can contain several ACTIONS USER LIST List of all users and their phone numbers which are used for ACTIONS User names are used only for better clarity SP9 does not use them in any Way DEVICE OFF Disconnection of SP9 from any form of power supply including internal battery DEVICE ON Connection of SP9 to any form of power supply Processor reset has the same effect POWER ON OFF Connection disconnection of supply terminals from external power supply SP9 supplied from internal battery can send SMS about Power recovery and Power outage 7 10 Remote Configuration SP9 can be configured remotely via GSM data connection CSD in the same way like via USB cable Note You need any GSM modem connected to your PC Just click in menu Options and in new window called Options set the Station s phone number for data connection to SP9 Click OK to close the window For connection select proper COM port which is used for communication with modem and press the button Connection Confirm the phone number Yes When the GSM connection is established2. 2 What is a phone number of SCA SCA Service Center Address of my mobile operator It s not possible to send an SMS Contact your mobile operator for this piece of information 3 I ve tested SP9 with my own SIM card Now I cannot find SMS messages formerly stored on my SIM card SMS from your SIM card were processed by SP9 and then deleted They were very probably canceled due to syntactical error 4 Where can I find more and up to date information re Search GSM SP9 product on the website www seapraha cz English pages 10 SP9 in box Special box for SP9 order code GSM SP BOX M with power supply type GSM PWR1 is produced Note This box has to be ordered separately and is designed only for SP9 slim variant GSM ant na Sitsletslals com x2 x4 xe x8 x1 x3 x5 x7 x9 Ate SMS PROCESSOR GSM SP9 www SEApraha cz Crea ve ve ws wr e v Soe oot GSM SP BOX M 230V Box parameters Width 166 mm Height 140 mm without connectors Depth 87 mm IP55 11 Warranty General warranty period is 12 months after purchase when eventual malfunction device will be repaired free of charge in SEA company while shipping to SEA is paid by customer and SEA pays for shipping back to customer For SW there is 24 months warranty under following conditions Both CPU and PC software is sold as is The software was created by the best software engineers in SEA and was ca
3. 20 tC Humidity Operational a a aa eaa eaaa a a SP9 is designed to be used inside a building only For outdoor use you need accessories SP9 BOX you can choose variant slim with dimensions w h d 60 x 90 x 53 mm order code GSM SP9 AS GSM SP9 DS or GSM SP9 TS 5 Hardware GSM antenna oOo Hea om OIE coje xs xe ea xt x3 x5 x7 x9 Ate SP9 under the top cover SMS PROCESSOR GSM SP9 Connector tor expansion board or unit Button SIM card reader SP9 status LED indication m www SEApraha cz Output status LED indication Ya 8 30V eae oe BOG a Da WW Wie WW Notes The button is intended for future use Terminals Al A1 GSM SP9 A analog input 0 to 20 mA connect terminal A1 to higher potential GSM SP9 T temperature sensor KTY81 210 polarity does not matter GSM SP9 D digital input X10 A1 X11 A1 Warning It s highly recommended to use extra power supply for SP9 power galvanically separated from power supply for input and output external circuitry especially when I O have long wires that may be noisy page 1 of 6 5 1 Digital inputs X 6 Remote Control Digital inputs SP9 input signals are connected to the input terminal where the COM terminal is common for all digital inputs X1 to X9 or X11 The figure shows an 6 1 SMS Message control example of the connection of external circuits and internal wiring of input X1
4. For each analog input is possible to set by the filter value in range 0 2 sec to 30 sec or without filter Remember after turn off page 3 of 6 If this box is checked analog input value and zone state will be remembered before shut down of SP9 After power on of SP9 the actual value and zone is compared with stored value and zone and the SMS message is send or not send depending on the change Actions and settings Here is possible to select what SMS messages or calls the SP9 device will send send when the analog inputs status changes see Events at the inputs for details 7 5 SPI Init Tab User List Device SP6 has one central user list For any action a user is chosen from this central user list 7 5 1 Existing users A Configuration tool SP Init changed File Options Phone number User phone number which is used for sending SMS messages or voice calls for this user Attention Authorization of incoming messages does not depend on the phone Information on device Type SP9 4 B Memory Size Version 2 1 Capacity 4096 Configuration 1154 Free 2942 T General We Digital Inputs sft Digital Outputs aga Analog inputs E User List pt Advanced Q Monitoring Existing Users Phone number 420777777497 Message prefix number the phone number is used only for send ing SM S or voice Users who get copy of all STATUS responses call Name a Read Ze Write E COMS v Connec
5. 20 mA can be displayed as the pressure of 0 5 MPa see the chapter Configuration program SP Init SP9 T Analog input is designed to measure the temperature 50 C 150 C using KTY 81 210 temperature sensor 7 Configuration For configuration of SP9 is used special program call SP Init This program can be downloaded free of charge from the website www seapraha cz GSM SP9 5 4 Front Panel The front panel of the SP9 includes SP9 status LEDs and inputs and outputs status LEDs The state is only shown for inputs X1 to X8 and all outputs Y1 to Y8 LED for Y7 and Y8 are located above the USB connector Program SP Init enables Under the removable cover is placed SIM card reader the button 9 intended for future use and a connector for connecting of expansion Local configuration of SP9 from PC via USB cabl board GSM SP CB2 or GSM SP CB5 or unit GSM SP EXP Ea commiguratione rom PC via USB cable Local monitoring of SP9 from PC via USB cable SIM card is inserted into the reader cut corner down and contacts to i Remote configuration of SP9 from PC via GSM network CSD center of SP9 Proper insertion can be identified by a mechanical click SIM a card can be removed by pressing gently on it until a click and release e Remote monitoring of SP9 from PC via GSM network CSD Then the SIM card can be pulled out Note No USB driver is needed because SP9 is a HID device type See Windows gt the Control Pane
6. and vice versa Re2 Y6 output switching power supply positive branch of the relay coil Re6 voltage relay must correspond to an external source voltage The polarity of the terminals C1 C4 and C5 C8 terminals is 6 2 Status SMS Text Message irrelevant can be plus or minus SP9 Whenever command SMS contains valid password SP9 always returns status SMS 8 30V Internal wiring 7 Status SMS contains following information Y1 Y3 cs ca ve pc a i lt Device Name gt lt LogInput1 gt lt LogInput1iStatus gt lt LogInput2 gt lt LogInput2Stat US gt lt LogOutput1 gt lt LogOutput1Status gt lt LogOutput2 gt lt LogOutput1Status gt lt GSM Signal Level gt C1 C4 ine K G K K amp vystupy Status SMS message contains information only about selected inputs and outputs Power supply oi Selection is done in configuration program SPInit by checking the appropriate External o SP98 to 30 V DC checkbox power supply 8 to 30 V DC SP9 Status SMS Explanation Example 5 3 Analog Input SP9 A and SP9 T only SP9 A and SP9 T versions have 1 analog input which is connected to the input Dini on Digital Input1ison sid terminals A1 A1 Din2 off Digital Input 2 is off __ SP9 A Analog input is designed to measure the current 0 20 mA The measured DOut3 on Digital Output 3 is on closed value 0 20 mA can be converted to user units For example the measured current from 4 to
7. is configured as current input 0 20 mA Pressure sensor gives 4 mA at 0 MPa and 20 mA at 10 MPa see settings in the picture E Analog input No A1 Tlak Type and Conversion Zones and Events High pressure 0 50 0 10MPa transition Low pressure Transition Cross at value 0 50 0 10 MPa Transition up Delay himis Action eteti Transition down Delay himis Action o ko 1 0 Xx B Analog input No A1 Tlak Type and Conversion Zones and Events Input type User units Transformation to user values and Value Format in SMS Measured quantity and jumper settings alue format Units XXX XX v MPa Conversion User MPa 0 00 4 0 0 00 Input m 10 00 C AD rt User onverter Zone Units Range MAX HIGH 100 kPa Increase Over Critical Level PRESSURE HIGH 71kPa et y MIDDLE Value PRESSURE MIDDLE 31kPa PRESSURE LOW 29kPa Increase on Operational Level Decrease below Operational Level 7 11 2 Macros Macros are useful when you need to get values or input and output states in event or status SMS messages HETO ge Meaning Example DINXNAME Digital input name Input AINI NAME Analog input name Pressure Use the following numbers instead of letter x 1 11 in Dinx as the number of digital input 1 8 at DOutx as the n
8. same l for all digital inputs The polarity does not matter COM can be plus or minus SP9 is controlled via SMS messages of GSM network Command SMS messages are GSM SP9 D has digital input X10 connected to terminal A1 and X11 to A1 in form lt PASSWORD gt lt COMMAND gt lt RETURN COMMAND gt External power supply cl spo Example co x2 x4 Xe xe At Px x3 x5 x7 x9 Ata 8 to 30 V DC PT TY FPP LT TF ieerai ilina Inputs 1234 STATE SP9 returns an SMS containing status of input X1 a 1234 DOUT1 ON SP9 output will be switched on Confirmation SMS will be Lo x1 returned q ph 1234 DOUT8 PULSE NOBACK SP9 pulse on output8 will be generated no io COM confirmation message will be sent back It s possible to write more commands into one command SMS For higher readability separate commands by semicolon inside command use 5 2 Digital outputs Y 1234 OUTPUTO ON OUTPUT1 ON OUTPUT3 PULSE Digital outputs SP9 output signals are connected to the output terminals where the terminal C1 C4 is common for outputs Y1 to Y4 and the terminal C5 C8 is common Names of inputs and outputs are user definable by SPInit program Command SMS for Y5 to Y8 The figure shows an example of the external and internal wiring Ay look like this circuits of output Y1 the same for all digital outputs Y2 output switches negative 1234 GATE OPEN HEATING ON LAMP BLINK branch power relay coil
9. to 30 VDC to the terminals and power on 3 If the power supply is OK the green LED PWR lights At the same time after about 20 seconds will briefly flash red LED GSM in the interval 1 for 3 sec 4 Send SMS text messages from a mobile phone in form 1234 STATE to the phone number of the SP9 The device responds with a status message in the form Test SP9 Window Closed elevator Heating system OK ON SIGNAL 53 To use other functions it s necessary to configure the device using the program SP Init see below 5 Install the SP Init program The current software version is possible to download free of charge at www seapraha cz site with GSM SP9 product Note No USB driver is needed because SP9 is a HID device type see Windows gt Control Panel System Hardware Device Manager gt Human Interface Devices if necessary 6 Run SP Init Windows Start Programs gt SEA gt SP Init gt SP Init Connect SP9 to your PC via a USB cable which is included in the package USB connector B is located under the small square cover on SP9 see the picture When GSM SP9_Users_Manual_EN_vi 14 docx 2013 04 26 VIL configuring SP9 with a USB cable SP9 must be connected to power Load the configuration from SP9 by clicking the Load Enter your phone number and rewrite the Paul s name on the User List 7 Modified configuration has to be written to SP9 Click the Write If you leave the USB cable conne
10. 923 These inputs have only two states YES NO Version 2 5 Free 3173 General Ea Digital Inputs gf Digital Outputs c7 Analog inputs User List ng Advanced Q Monitoring Text in messages Change notifications Remember State L State H after turn Input Transition L gt H Transition H gt L Name of input State name State name Delay h m s Actions Delay h m s Actions 0 0 1 10 0 1 Window closed opened These texts will appear in T Jo fanre the status SMS gt 10 1 j Joa 10 1 10 1 10 1 10 1 Note Inputs DIni0 and DIn11 are not available for the SP9 A and SP9 T 10 1 20 1 10 1 10 1 0 o fo 0 0 0 J0 O 40 0 1 0 0 0 0 0 0 10 1 0 1 w N a a lt AARAYANANAA OAAANANANAA o o o o o o o o o 0 0 0 0 1 0 0 0 0 0 j0 0 1 20 1 Mention in State SMS Neg Disconnect Connection Connected pal iOOOoOoOmsm o a Read J Ze Write ta 7 2 1 Text in Messages Input Name State L State H These fields contain names of inputs and their possible states which are listed in the status SMS message Example When we assign nput as Input1 State L as Off and State H as On the part of SMS status message concerning Inputi will look like this Input1 0n Mention in State SMS If this box is checked the status of th
11. Configuration tool SP Init Efe Options information on device Type SPPA SPE Version 3 21 7 1 1 Initialization Enter 4 to 8 digit PIN code of the SIM card which is inserted in the SP9 device Leave the PIN field empty if usage of the PIN code on the SIM card is disabled ory Soe Capacty 4096 Configuration 2421 Free 1675 Re Bi Genera 2 Digtal Inouts oh Digta Outputs ae Andoginputs G User List re Advarced Q Montoring Initialization PIN V Show Battery charge n Remember SupplyDisconnected Connected after tum Name of input State name State name of Power recovery Power outage f Delay homes Action Delay himis Action o fF o 4 0 lot A o o joa S 0 T_ mention in State SMS Negate PWW paw ofi on 7 Ignore Din Everts Without Pw w 7 1 2 Response to STATE The Station Name identifies sr w 5m sta crei2ns the SP9 device This text is placed at the beginning of every sent SMS message It s also possible add items Show Battery status and Show GSM strength to status SMS by checking these items v Connect Comnection Port freed amp 7 1 3 Special actions Use button Actions on power supply recovery to specify the text of SMS messages or voice calls which the SP9 device sends on startup see chapter Inputs Events 7 2 SPInit Tab Digital Inputs On this tab you can set t configuration of all digital ee n ish in puts of SP9 device Type SP9 A Capacity 4096 Configuration
12. SP9 User s Manual 1 Introduction GSM SP9 SP9 for short is a device for remote monitoring and control via GSM network There are three variants of SP9 which differ in usage of input terminals A1 A1 see variants of SP9 The number of digital outputs eight inputs is the same for all variants Outputs can change its status or generate pulse depending on SMS command SP9 can react on input changes by sending an SMS and or by a voice call Functions input and output names phone numbers passwords etc are fully user configurable from personal computer either locally via USB cable or remotely via GSM data call CSD using modem and program SP Init This configuration program SP Init can be downloaded free of charge from the website www seapraha cz English pages gt Support gt GSM SP9 The SP9 box has an integrated DIN rail mount so you can comfortably place SP9 in the cabinet Variants of SP9 GSM SP9 A 8 digital outputs 9 digital inputs 1 analog input 0 to 20mA GSM SP9 D 8 digital outputs 11 digital inputs GSM SP9 T 8 digital outputs 9 digital inputs 1 analog input temperature range 50 C to 150 C Each variant is equipped with internal Li Ion backup battery 1 SIM card holder located under the cover 2 USB connector under the square cover 3 Outputs Y 8 outputs 2 x 4 4 DIN rail holder 5 Power supply 8 to 30 Vpc 6 LED outputs indication 7 LED SP9 status indication 8 LED inputs in
13. cation on Dig Output Selected output is on when the SP9 is connected to GSM network This function is typically used when indication of GSM connection is necessary 7 7 SPInit Tab SP CB SP9 T Tab SP CB SP9 T is intended for special purposes only 7 8 SPInit Tab Monitoring Ka Monitorin Program SPInit enables to watch fso status of inputs and outputs on Termi Unf Name Value Zone Age PC monitor in tab Monitoring ean ees Dig output 1 Automaton state Monitoring can be local via USB a U ha SSSS SY cable or remote via GSM data Gsm operator vodafone connection CSD It s possible PAR manak i to switch on or off digital Digital outputs outputs by clicking on pushbutton Change or Pulse Doutz It helps to check function of a TTT external circuitry Ba DoOut6 Dig output 6 DOut Dig output 7 Dig output 2 Dig output 5 Hoos h tows DOut H Dig output amp 4 Analog inputs 7 8 1 Operational status List of actual information concerning the SP9 device and it s functioning Automaton state Signal strength GSM operator Information for service purposes only GSM signal level in Actual GSM operator s name 7 8 2 Digital inputs outputs and analog inputs List of actual status of all digital inputs outputs and analog inputs Terminal The terminal name Unfiltered Measured values of the inputs or outputs of the device ar
14. cted you can monitor the current state of SP9 inputs outputs and status 8 Digital inputs signals in SP9 are connected to terminals X1 to X9 or X11 and digital outputs signals out of the SP9 are connected to terminals Y1 to Y8 Schematics of these signals are listed in the Hardware section In the event of any change on any input SP9 can send to your mobile phone SMS message in the form as Input1 is closed the text depends on SP9 configuration 4 Technical specifications Parameter Unit Width w y Jr mm oe ee e GSM antenna Ts a C between DIN 53 slim rail and cover po 80 Ve Current cc _ VYc 12V_ J 05s JA Supply Average Pce 2 5 _ W power a Pt 11 DC any Volagebg H vu e r polarity veseri o aa V Current mM E Number CT J 8 oa Mee vo __ 30 _ Voc outputs DC Voltage AC Voue 85 Vc AC Current DC Tourne io mA Current AC Toura 70m Number C E eee ee eee ee Measured value Current with user selectable conversion ile Measured 20 mA current analog current input Al Input Current input Resolution 7 Resolution TTY bits SP9 T oo E ERE E E E temperature Range J 5 50 C log input oe a Recommended temperature sensor GSM C T2 for temperatures 20 to 55 C GSM C T2 sensor accuracy is 1 C in the range 0 C to 30 C 800 1800 MHz ces Baa f 800 900 1800 1900 MHz on special order 7 Temperature Operational ts
15. dication 9 Analog input 0 to 20 mA 10 GSM antenna connector 11 Inputs X 9 SP9 A SP9 T 11 SP9 D 2 Package 1 pc GSM SP9 see variants 1 pc GSM antenna order code GSM ANTO5S 1 pc USB cable A B order code HW 11 02 8818 1 pc printed documentation this manual Accessories has to be ordered separately GSM SP BOX M Temperature sensor GSM C T2 for GSM SP9 T range 20 C to 50 C 3 Installation Before inserting the SIM card into the SP9 it is highly recommended to turn off setting of the PIN code Insert the active SIM card at least one call was made to any mobile telephone and turn off the requirement of setting the PIN On most mobile telephones this option can be found in menu Setting the telephone protection or Setup gt Security gt PIN control Note The PIN is possible to activate later when the user became familiar with the configuration procedure of SP9 1 Before power on the device SP9 insert an activated SIM card call the helpline operator to the SIM card reader under the removable cover and connect GSM antenna SIM card is inserted into the reader by cut corner down and contacts the center of SP9 Proper insertion can be identified by a mechanical click SIM card is removed by pressing gently on it until you hear a click and release Now the SIM card can be freely pulled out 3 2 Connect the power supply voltage from the DC voltage source 8
16. e usually filtered to avoid often change of state In this box you will find the real value of the input device This is useful especially when the delay is set to a larger transition time e g 1 hour Name Name of input or output Value Analog input value Zone Analog input zone e g low high Age Input values are not updated immediately Depending on CPU values may be delayed up to 20 seconds This field will show when an item has been measured last time When any output is selected it s possible to use the right mouse button to change the status and generate a pulse This is useful for testing the function of the external circuits connected to SP9 Please be patient after pressing the change of output may take some time e g 20 seconds when connected via GSM page 4 of 6 7 9 SPInit Important Terms Explanation PIN Personal Identification Number usually four digits number Only persons with knowledge of PIN can operate a SIM card in case the PIN usage on a SIM card was activated Usage of the PIN can be deactivated Insert the SIM card to your mobile phone and follow the instruction in the mobile phone manual Usually the PIN usage can be deactivated in Menu gt Security gt PIN ACCESS CODE Password for SMS commands configuration and monitoring of SP9 accepts only SMS with a valid access code The password is requested also for connection of SP9 via USB cable or remotely via data connection of GSM network
17. he value L means SP9 is battery powered Events and state SMS are configured like for any other digital input 7 3 SPInit Tab Digital Outputs On this tab you can set KA Configuration tool SP Init configuration of all digital fte options Help outputs of SP9 device egea These outputs have only two states YES NO Memory Size Version 2 6 Capacity 4096 Configuration 934 Free 3162 General N Digital Inputs Digital Outputs c7 Analog inputs User List a amp Advanced Q Monitoring Text in messages Impulses Output State L State H Name of output State name State name Startup These texts will appear in Heating off on the status SMS ni A Command to begin Duration him s O 40 10 0 Remember w test State L O 40 0 1 State L o klo lloa State L 3 0 3 0 1 State L 10 1 v bs v h b bi 0 o o State L o llo loi State L o llo loi o llo 10 1 Negate t 00000000 fe ies es fe N N State L b Mention in State SMS Connection Connected 7 3 1 Text in Messages Output Name State L State H These fields contain names of outputs and their possible states which are listed in the status SMS message AA the Output Outputi Status L Off and Status H On than you will see the following text in the status SMS Output1 off Mention in State SMS If this box is checked the status of this outpu
18. is input will appear in the status SMS message Remember after turn off If this box is checked the digital input state before switching off of the SP9 will be remembered This is important when SP9 has to send an SMS message or make voice calls and the input state changes during a power on of SP9 Details are provided in analog inputs 7 2 2 Change Notification Transition L gt H transition H gt L When the input level is changed than after delay which is necessary for the recognition of the input state the requested action SMS or voice call is performed Delay h m s Specifies how long new input state must be stable before action is executed Note the delay timers are nonlinear and it may happen that the program adjusts your choice at the earliest possible time e g 25 0 5 is adjusted to 25 0 0 Actions Here is possible to select what SMS messages or calls the device has to send when the status changes see Events at the inputs Actions SMS or voice calls to be done on the transition of input signal See the chapter Inputs Events Negate If this box is checked the meaning of states L inactive and H active is opposite 7 2 3 Internal input PWW power SP9 has an internal digital input PWW internally X12 input e g for MACRO which monitors the supply voltage The value H means the SP9 is powered from external GSM SP9_Users_Manual_EN_vi 14 docx 2013 04 26 power supply T
19. it s possible to operate the SP9 in the same way like via USB Note Press Disconnect when your task is finished Language Stations list Si English v i Device SP9 Station name Device SP9 Operation Basic O Advanced Station s phone Expert 777777497 Password P ejete a vyto it cisl 420777777497 x l Ano 1 Ne j Storno 7 11 Events SP9 can be set up to inform about events changes on its digital and analog inputs SP9 sends information via SMS message or makes a voice call By the SPInit program is possible to set several actions for each event specifying the phone number user who will receive an SMS message and who will be called A various SMS can be sent to and a voice call can be made to more phone numbers from the list The order of SMS and voice calls depends on a list of actions for each action Voice call rises the probability the user will not miss received SMS message 7 11 1 How to create an Event First of all the Event has to be created in the configuration program SP Init Click by a mouse on the symbol of a key Al By pushbutton ADD select requested action of SP9 SMS or voice call write the text of SMS which has to be sent or insert the sequence of DTMF numbers in case of a voice call Now select a user and add him to a list of users for this event by a click on an arrow gt gt Please check carefully the number of users for an event In case the
20. l System Hardware Device l A 2 Base variant Manager Human Interface Devices if 5P9 4 necessary O 5P9 D X O SP9 T USB connector for PC connection is hidden under the square cover Select installed options Meaning Light Blink 1x SPSBOA SPSEXP No extension v After installation during the first run of the configuration program SP Init it is necessary per 3sec to select the device variant SP9 A SP9 D Power ON green Power OFF or battery powered SP9 T Select expansion unit SP9EXP if connected or No extension GSM OK no GSM other card normal Signal GSM error teh pea After connecting the USB cable to SP9 the proper COM port is selected automatically co i SP9 OK SP9 has to be powered After pressing the Connect SP9 establishes normal Error o Error communication with the PC see the Connection Connected Now it is possible to operation during transition time before input i jee ul elie 4 pera is 5EA G9212002 v Connection Port freed IN i activated activated accepted after input change before SMS can be sent l 7 1 SPInit Tab General read change and write configuration to SP9 or read it or write to a file on PC ouT 9 activated en In the General tab you can set up the PIN for the SIM card station name event after turning on the device and internal inputs GSM SP9_Users_Manual_EN_v1 14 docx 2013 04 26 page 2 of 6 HF
21. least two bars Check the credit on prepaid SIM card contact your operator if necessary Test the SIM card in your mobile phone Test the SIM card in your mobile phone Sending receiving SMS voice call data call Contact your GSM mobile phone operator if you have any problem with SIM card in your mobile phone Make a small video of LED diode blinking on SP9 and send it to service Check the SCA center setting on SIM card and in SP9 configuration program SPInit Contact your mobile operator to be sure CSD data tariff is active for both SIM cards in SP9 and in Modem Note CSD data is not GPRS 9 Frequently Asked Questions 1 What is necessary to use SP9 successfully SIM card capable to send and receive SMS messages from standard mobile phone and voice data call incoming and outgoing as well Please test all these functions in your mobile phone It s important to solve all possible problems before using SIM card in SP9 Contact your mobile operator if necessary Good quality GSM signal in area of installation of SP9 at least 2 bars on your mobile phone If there is a problem with GSM signal quality try to use another type of external antenna which can be placed in proper place with better GSM signal and which is connected to SP9 with several meters long coax cable with SMA connector Sufficient Credit in case of prepaid SIM card Cancel all phone calls redirection for a SIM card in SP9
22. number of users is zero nothing will happen no SMS will be sent Fd Analog input No A1 Current Type and Conversion Zones and Events Input type User units Transformation to user values and Value Format in SMS Measured quantity and jumper An event for the analog TAE input can be created in the folder Analog inputs Click by mouse on the symbol key J In the Type and conversion can be set alue format Units XXXX X v m Conversion Input m Input type Note Analog input Al is current type 0 20 mA SP9 A or temperature SP9 T and cannot be changed User units GSM SP9_Users_Manual_EN_vi 14 docx 2013 04 26 Here it is possible to select the format of the values not for internal inputs which used for displaying and the unit values Conversion In this table you can specify your own conversion of input values to be displayed not for internal inputs In the tab Zones and events can be set the name of the zone and the limit value with hysteresis Whenever the actual value is inside the zone the zone name is displayed in the status SMS message Furthermore is possible to set up the action which will be executed after the input level transition above or below a certain level after a specified delay Setting of actions and macros is the same as for the digital inputs Example Sample configuration with the analog input values conversion to user units Analog input
23. oblems with sending SMSs Expert modem settings O Try indefinitely Service centre SCA Constrain number of tries to i Initialization commands 3 1 31 On problems with Yoice calls O Try indefinitely Constrain number of tries to 3 3t Indication of device readiness Indicate on Dig Output i Connection Port freed GSM SP9_Users_Manual_EN_v1 14 docx 2013 04 26 7 6 1 Automatically repeated actions Action Group A Action Group B Allows you to specify the time period after which SP9 executes the specified list of events This is useful e g for automatic reporting that the device is functional and can communicate via GSM network This feature is called alive 7 6 2 On problems with sending SMS Specifies how many attempts to send an SMS are made when any problem appears in GSM network The range is 1 to 31 attempts 7 6 3 On problems with Voice call Specifies how many attempts of voice call are made when any problem appears in GSM network The limit range is 1 to 31 attempts 7 6 4 Expert modem setting Service center SCA Leave empty It is intended for users who have special Service center Initialization commands Specifies AT commands which the device sends into the GSM modem at startup ATTENTION Commands in this field may cause malfunction of the device Enter commands only after consultation with the manufacturer of the device 7 6 5 Indication of device readiness Indi
24. refully tested both in SEA and also by SEA customers using GSM applications products made in SEA In spite of making all possible to get error free software it can happen that the software in CPU or PC programming SW or their mutual interaction has some error under some specific conditions If such error is found and the description of the problem including configuration file is sent by E mail to SEA Itd the error is removed free of charge and SEA will send new SW by E mail to customer SEA ltd has NO RESPONSIBILITY for any damage lost costs and any other problems direct or inducted caused by such SW error by eventual device malfunction from any reason or by undelivered SMS from the device page 6 of 6
25. t will appear in the status SMS Startup After power on the SP9 can set an output to State L State H or retain the status output that was before power off option Remember 7 3 2 Command Impulses The text used in the command SMS for generating of a pulse on the output e g pulse Duration h m s Specifies duration of the output pulse Note the duration timers are nonlinear and it may happen that the program adjusts your choice at the earliest possible time e g 25 0 5 is adjusted to 25 0 0 Negate If this box is checked the meaning of states L inactive and H active is opposite 7 4 SPInit Tab Analog Inputs On this tab is selected configuration for analog input A1 variant SP9 A and SP9 T 7 4 1 Text in Messages Analog Input Name EF Configuration tool SP Init These fields contain names of inputs and their possible states which are listed in the status SMS message hi General 2 Digtal Inputs Digtal Outputs Text in messages Name of input Al Current Example When we assign Jnput Al as Current and check the Zone and Value the part of SMS status message concerning input Mention in state message A1 will look like this s See oo tl Current High 20mA for example Mention in state message If this box for Zone and or Value is checked the Zone and or Value of this analog input will appear in the status SMS message Filter constant
26. tion Port freed User name This area is not used by SP9 device It is useful for better orientation in list Code User code This code is used for authorization of incoming command messages Received SMS are executed only if it contains code of some user in your user list Message prefix The text which is added in front of SMS message for this user It is used for sending messages e g at e mail This message is usually sent on special phone number e g 4616 and first in message is an e mail address Pulse on Call The voice call from user s phone number results into pulse on the selected output Dout1 to Dout8 Select item for no pulse The pulse duration can be set in the Digital Outputs in area Impulses 7 5 2 Lists Users who get copy of all STATUS responses Choose users to whom the copy of status massage is sent whenever any status message is about to send 7 6 SPInit Tab Advanced On this tab are placed special advanced features of the SP9 KA Configuration tool SP Init File Options Information on device Type SP9 4 SP9 EXP Memory Size Version 3 21 Capacity 4096 Configuration 2421 Free 1675 General aes Digital Inputs ry Digital Outputs a Analog inputs E User List Advanced Q Monitoring Automatically repeated actions e g periodic status report Action Group 4 Action Group B Period days hours Action Period days hours Action C Perform C Perform On pr
27. umber of digital output Example Event SMS prepared in configuration Alarm Details DIN1 NAME DIN1 VALUE DIN5 NAME DIN5 VALUE AIN1 NAME AIN1 VALUE AIN1 STATE Battery BAT Signal SIGNAL An incoming SMS message Office Alarm Details Door open Safe Ok Pressure 0 2Pa Low Battery 75 Signal 68 page 5 of 6 8 Troubleshooting Problem Problems during installation of SP9 SP9 is not available on GSM network Problems during operation of SP9 SP9 has problem with SMS sending Problem with remote configuration via GSM modem Warning Don t locate GSM antenna too close to SP9 analog inputs due to possible Possible reason No power supply Bad or not activated SIM card Low credit on prepaid SIM card Low level of GSM signal Low credit on prepaid SIM card Prepaid SIM card is no longer valid because credit was not paid for long time Usually for more than a year Other reason SIM card has not active CSD Circuit Switched Data data noise interference GSM SP9_Users_Manual_EN_vi 14 docx 2013 04 26 Solution Check power supply Test the SIM card in your mobile phone Check the credit on prepaid SIM card contact your operator if necessary Check the connection of GSM antenna Check the GSM signal level in the place where is located GSM antenna for SP9 Use your mobile phone with SIM card from SP9 Signal level has to be at
Download Pdf Manuals
Related Search