Home
Installation Manual
Contents
1. Tx Rx Frequency MHz 58375 58375 RSSI dBm 48 ts 50 Vs 100 35 100 35 CINR d8 23 Gn q 22 WE AN o 25 o 25 Mode Adaptive QAM64 4 1 0 5 Adaptive QAM64 4 1 0 5 Estimated Throughput Mbps 1000 1000 2014 07 21 12 46 50 link down eth eth1 45 j Active Alarms 2014 07 21 12 46 50 link down eth eth2 tap peri Ss 2014 07 21 12 46 50 link down eth eth3 peta SE History Log Show Export Clear Show Export Clear User Activity Log Show Export Clear Show Export Clear Save Local Configuration Reset Local Timeout sec Start Rollback Save Remote Configuration Reset Remote Figure 3 3 Web Based Management Main Page Page 32 EH 600T Installation Manual 3 2 Main Page The Web Based Management provides link view presenting both local and remote configuration and monitoring Although the local and remote systems IP address is identical default IP address 192 168 0 1 the remote will be available as well as the EtherHaul uses dedicated communication channel for local remote communication that is not IP based It is recommended however to assign dedicated IP address for local and remote systems Depending on your station s screen size and resolution you may need to scroll the Note screen vertically or horizontally in order to view all options for local remote Zoom out using Ctrl Minus A Alternatively you may change the change the Internet s
2. S gt EtherHaul 600T Gigabit Ethernet Wireless Solution Installation Manual EH600 INST 03 Issue 3 February 2015 ALL RIGHTS RESERVED TO SIKLU COMMUNICATION LTD EH 600T Installation Manual Trademarks Siklu the Siklu logo and EtherHaul are all trademarks of Siklu Communication Ltd All other product names and trademarks mentioned in this document are trademarks or registered trademarks of their respective companies Copyrights Copyright O 2014 Siklu Communication Ltd All rights reserved No part of this publication may be reproduced or distributed in any form or by any means or stored in a database or retrieval system without the prior written consent of Siklu Disclaimers The information contained in this document is subject to change without notice Siklu assumes no responsibility for any errors that may appear Siklu makes no warranties expressed or implied by operation of law or otherwise relating to this document the products or the computer software programs described herein This document was originally written in English Please refer to the English language version for a full and accurate description of all products and services described herein Page 2 EH 600T Installation Manual About this Document This document is the Installation Manual for the EtherHaul 600T wireless Link It provides product overview and details the installation and initial setup For in
3. Output on Eth3 VLAN IEEE 802 1q and VLAN stacking Q in Q IEEE 802 1ad Provider Bridge IEEE 802 1d Transparent Bridging Ethernet features Advanced QoS amp Traffic management 802 1p DSCP amp MPLS EXP O Scheduling Shaping Policing MEF 9 14 and 21 compliant Ethernet OAM and CFM IEEE 802 Lag ITU T Y 1731 IEEE 802 3ah Page 14 EH 600T Installation Manual e Ethernet Ring Protection ITU T G 8032 e MAC learning e Link state propagation e Jumbo frames hs e JEEE 1588 TC Synchronization e Synchronous Ethernet ITU T G 8261 8262 8264 Network topologies e Ring daisy chain and mesh In band out of band embedded CLI web GUI SNMPv2 3 Adaptive modulation System modes Symmetrical uplink downlink ratio or Asymmetrical Alignment l Operating temperature 45 50 C Environmental Ingress protection rating IP67 ETSI EN 302 217 3 UK IR 2078 amp IR 2000 Regulatory USA FCC Part 15 255 CE marked EMC safety Dimensions ODU Antenna Hx W x D 15 cm x 15 cm x 8 cm 1 4 Licensing The EtherHaul family provides for easy migration to support Gigabit throughput enabling operators to enhance bandwidth capacity on a pay as you grow basis as well as adding features and capabilities according to their networks evolutions You can order the following EtherHaul software capacity steps and feature availability depend on your platform Data rates Layer 2 networking capabilities OAM and Resiliency
4. D Link distance in Km F Frequency in GHz Attatm Attenuation due to Atmospheric Gases dB Km For E band links the Attenuation due to Atmospheric Gases is typically 0 5dB Km For V band links the Attenuation due to Atmospheric Gases is significantly higher up to 15dB Km and depends on the specific channel used and the exact geographical location Refer to EtherHaul Link Budget Calculator for on line calculation of expected availability and expected RSSI Page 21 EH 600T Installation Manual 2 6 Mounting the EtherHaul 1 Elevation Lock Bolts 1 additional bolt at opposite side of the mount 2 3 4 5 6 7 Elevation Fine Adjustment Screw 10 60 Azimuth Fine Adjustment Screw 10 ODU Mounting Hooks Azimuth Lock Bolts 2 additional bolts at opposite side of the mount Worm Clamp fixing points Worm Clamp Figure 2 1 EtherHaul 600T Mounting Bracket 1 Prior to mounting unpack the mounting bracket package and thread the worm clamps through the worm clamp fixing points at the back of the Mounting Bracket ei 2 Attach the ODU to the Mounting Bracket by sliding it to the 3 Mounting Hooks and lock the mounting bolts The ODU is shipped with 3 mounting bolts on the top of the ODU 2 on the top and one on the side In this position when installed the mounting bracket will allow elevation of 10 60 In case elevation of more than 10 is needed when shooting upwards t
5. Master Slave Master Slave Modulation Mode Adaptive Adaptive Mode modulation sub channel repetitions FEC Static IStatic UL DL Configuration ISymmetric JAsymmetric ratio Ethernet Services Tests Frame Loss test No Frame Loss No Frame Loss Packet Analyzer SW based Test duration Test duration JEtherHaul Statistics Page 50 EH 600T Installation Manual IP address 1 amp C Details I amp C Date Page 51
6. The ODU will work on the highest modulation profile based on the CINR values of the both sides and will present the current modulation profile Adaptive mode is the normal and recommended mode of the radio link Alignment Status R O field indicating that the ODU is currently in Alignment mode by configuration or by inserting DVM probes Alignment Probe when checked the ODU will use the Alignment Cap Screw status as alignment indication when removing the screw the ODU will switch to Alignment When unchecked the ODU will not switch to alignment mode is the screw is removed Note i It is recommended to disable the Alignment Probe indication after link is installed Transmit Asymmetry Default value is symmetric configuration 50 for Tx and Rx 50tx 50rx For an asymmetric configuration 75 25 or 90 10 Role has to be set the Master unit transmits the higher rate 75tx 25rx or 90tx 10rx and the Slave unit the lower rate 25tx 75rx or 10tx 90rx When selecting asymmetric configuration Role will be set automatically refer to Radio Advanced Settings Note Asymmetric configuration depends on product s specs and is relevant only for TDD systems Page 42 EH 600T Installation Manual 3 5 2 Advanced Settings Settings red ai Normal E Normal EI ATPC Target RSSI 35 Min Tx Power 35 Min CINR 128 C Targe
7. Config Main IP Address Type Le Eth Ports 2 Static iv Radio Eth Ports LOCAL 192 168 0 1 Name EH 1200F IP Address Prefix length System VLAN 192 168 0 1 24 10 10 10 1 24 Network Services a H REMOTE Status Link Up Name EH 1200F Type IP Address Advanced Config Statistics Hel Prefix length VLAN 1 Static sl 192 168 0 1 24 0 2 static Vv 10 10 10 2 24 0 Add IPv4 Add IPv6 Add IPv4 Add IPv6 Default Gateway IP Address 10 10 10 250 IPv6 Address IP Address 10 10 10 250 IPv6 Address d SNMP Managers IP Address Add UDP Port Secu Nam SNMP Ver Engin ID IP Address UDP Port Security Name Add ke Apply Figure 3 8 Quick Config Page Step 4 Network This section allows configuring the following parameters IP Address SNMP Ver Engin ID The EtherHaul supports up to four IP addresses that can be associated with different VLANS IPv4 or IPv6 can be configured IP addresses may also be acquired by DHCP o Index 1 4 Page 39 EH 600T Installation Manual 3 5 o Type Static or DHCP o IP Address Default is 192 168 0 1 o IP Prefix Length Default is 24 equivalent to Mask of 255 255 255 0 o VLAN 0 not defi
8. EtherHaul can gain up to 21 dB in link budget by dynamically adapting Modulation FEC coding rates and channel bandwidth maintaining the high priority traffic using quality of service advanced mechanism and dropping the traffic according to the QoS priority defined by the user Page 12 EH 600T Installation Manual 99 99 SOOMbps 52 6 min 4 a Internet email background traffic 99 995 a 2 200 Mbps 26 3 min amp S z Streaming media interactive traffic 99 999 20 Mbps 5 3 min Voice synchronization real time traffic signaling and control Figure 1 1 Hitless Adaptive Bandwidth Coding and Modulation 1 2 Functional Description The EtherHaul is an all outdoor system comprised of the following functional blocks RFIC Siklu s integrated Silicon Germanium SiGe transceiver operating at 57 66GHz EH 600T 71 76GHz EH 1200 EH 1200T or 71 76 81 86GHz EH 1200F Modem Baseband ASIC Siklu s modem baseband ASIC includes the modem FEC engines and Synchronous Ethernet support Network Processor the networking engine is the heart of the high speed bridge router function The engine receives packets from Ethernet interfaces the modem and CPU It is responsible for proper forwarding between these all interfaces Interfaces The network interface consists of 2 4 integrated 100 1000 Ethernet ports depends on the product type Host processor CPU the host processor controls the system responsib
9. Figure 3 9 Radio Page Settings This section allows configuring the following parameters e Channel Bandwidth MHz 250 or SOOMHz default is SOOMHz Note 250MHz support depends on product s specs and SW release e Tx Frequency MHz transmit frequency e Rx Frequency MHz R O field updated based on Tx frequency o For TDD systems identical Tx and Rx frequencies e Tx Power dBm ODU s transmit power Default is the max power based on product s specs Minimum configurable Tx power is 35dBm note that actual minimum Tx power is based on product s specs Note Adjust Tx Power so the RSSI at the remote end will not exceed 35dBm overload threshold The Tx power value sets the transmit power for the highest modulation profile In case lower modulation profile s has higher max Tx power based on product s specs the Tx power will be increased automatically without indication in RF configuration menu e Mode operational mode of the link o Alignment Carrier Wave transmission Used for antenna alignment No data over the radio link Page 41 EH 600T Installation Manual Note When exiting Alignment mode perform system reset to allow proper operation of the radio link o Static Fixed modulation profile If you select Static you must select from a list of pre configured modulation profiles in the Modulation field o Adaptive Adaptive Bandwidth Code and Modulation
10. Management Main Page 32 Fiure 3 4 Copy Ke Remote dC OM EEN 35 Figure 3 5 Quick Conte Page SEDL EE 36 Figure 3 6 Quick Config Page Step 2 Radio 37 Figure 3 7 Quick Conte Page Step EE Otter eege eegen 38 Figure 3 8 Quick Config Page Step 4 Network 39 Pisur 3 9 Radi Pace KEE 4 Figure 3 10 Radio Page Advanced Seri sisses rrenat SASE SSS 43 Figure 3 11 Radio Page Maintenance accuses hrean EEEE E E AEE EEEE EEEE EEE EEE E 44 Figure 3 1 gt Radio Page Modulation Tables eeh E 45 Page 9 EH 600T Installation Manual Introduction to the EtherHaul System This chapter provides a brief overview of the EtherHaul product line The EtherHaul radio delivers carrier grade wireless point to point gigabit Ethernet services utilizing the 57 66GHz unlicensed V band and the light licensed 71 76 81 86GHz E band spectrum The EtherHaul is based on Siklu s revolutionary integrated silicon technology which results in a highly reliable zero footprint and low cost radio The EtherHaul offers Gigabit throughput MEF compliant networking 8 levels of QoS enhanced Hitless Adaptive Bandwidth Coding amp Modulation for maximum spectral efficiency and services availability It supports network synchronization advanced OAM amp PM tools and ring protection optimized for both small cell and mobile backhaul It features multiple GbE interfaces including optical supporting complex network topologies such as daisy chain ring and mesh The m
11. Slave unit the lower rate 25tx 75rx or 10tx 90rx When selecting asymmetric configuration Role will be set automatically refer to Radio Advanced Settings Note Asymmetric configuration depends on product s specs and is relevant only for TDD systems Click Next to continue or Back to return to previous section Quick Configuration Step 3 Eth Ports A LJ A LJ EE Eth1 M Eth2 M Etha M Eth1 WW Eth2 M BIER Port Type RJ45 RJ45 RJ45 RJ45 RJ45 RJ45 Radio Port Enable M iv wd iv v v Auto Negotiation M M Eth Ports Speed Duplex 1000FD K wI M E per BZ Figure 3 7 Quick Contig Page Step 3 Eth Ports Page 38 EH 600T Installation Manual 3 4 4 This section allows configuring the following parameters Port status visual display Green port is up Port Type RJ45 or SFP Port Enable checkbox to enable the port Auto Negotiation checkbox to enable auto neg Speed Duplex speed 10 100 or 1000 and duplex half full setting o When Auto Negotiation Enabled R O field indicating the current speed duplex o When Auto Negotiation Disabled allows configuring the soeed duplex o R O field indicating the current speed duplex note that for SFP ports only 1000 speed is available Click Next to continue or Back to return to previous section Quick Configuration Step 4 Network Radio 1 Static Quick
12. alarms and date amp time raised e History Log System alarms and events history log e User Activity Log All configuration changes are logged including user and date amp time presented in the form of CLI commands Note i To view logs pop ups must be enabled and allowed on your Internet Browser General Configuration Commands Apply Any configuration change is executed upon clicking Apply The Local Remote concept of the Web Based Management allows configuring both local and remote systems of the link The Apply button is available at the bottom of each configuration page one button for both local and remote systems When clicking Apply the configuration changes will be sent to remote system first and then to the local system If multiple parameters changed on the page before clicking Apply all parameters are sent in bulk to the system and then executed locally in order to avoid losing management connection Save Configuration Any configuration change applied should be saved using the Save Configuration button Page 34 EH 600T Installation Manual 3 3 3 3 3 4 3 3 5 The system has two configuration banks 1 Running Configuration the currently active configuration Every time Apply is clicked the Running Configuration is updated 2 Startup Configuration the configuration the system will come up with after the next reset This configuration may be different than the currently active configu
13. e Synchronization Synchronous Ethernet ITU T G 8261 and IEE 1588TC e Encryption Vlan configuration and Provider Bridge settings capabilities are enabled by default and do not require a license The software licenses are serial number dependent Page 15 EH 600T Installation Manual 1 5 Management You can manage an EtherHaul system using a Web Based Element Management System Web EMS or a Command Line Interface CLI The CLI is compatible with SNMP Advanced network features must be managed using the CLI The EtherHaul system features a wide range of built in indicators and diagnostic tools for advanced OAM functionality The system is designed to enable quick evaluation identification and resolution of operating faults Page 16 EH 600T Installation Manual 2 Installing the EtherHaul System This chapter describes how to install and perform the basic setup for EtherHaul outdoor unit ODU in an EtherHaul wireless network including e Preparing the Site e EtherHaul Package Content e Unpacking the EtherHaul e Required Tools e Preparing for Installation e Mounting the EtherHaul e Connecting the Cables e System LEDs e Aligning the Antenna e Link Up Verification The installation of the EtherHaul system is followed by initial system setup that will be described in the next chapter Page 17 EH 600T Installation Manual 2 1 2 1 1 The installation and maintenance of the EtherHaul link should only be do
14. 2 Rubber Gasket Insert 4 Ethernet Cable Figure 2 5 All Weather Connecting Cable Shell Assembly Three sets of rubber gasket inserts are provided for different cable diameters e 4 2mm inner diameter for cable diameter 3 5 4 9mm e 5 8mm inner diameter for cable diameter 5 0 6 7mm e 7 9mm inner diameter for cable diameter 6 8 9 0mm For each ODU cable connection perform the following procedure 1 Disassemble a protective shell by unscrewing its parts and carefully removing the rubber gasket insert from the cable inlet portion of the shell Thread the cable connector through the cable inlet portion of the shell through the rubber gasket insert and through the connector outlet portion 8 Connect the cable connector to the ODU interface Screw the connector outlet portion to the ODU firmly by hand do not use tools Insert the rubber gasket insert snugly into the connector outlet portion of the shell Screw the cable inlet portion to the connector outlet portion firmly by hand do not use tools Page 26 EH 600T Installation Manual 2 1 5 2 1 6 2 1 1 Removing Connectors from the EtherHaul ODU Caution S To avoid accidental damage to the connector always use the following order to remove cable connections from the ODU Unscrew the cable inlet portion of the All Weather shell to release the gasket seal and then remove tension from the cable connector
15. Browser display distance The Web Based Management Main page is a read only page and displays the following information Link Status Link up or down with visual indication Link Length m link calculated distance between the local and remote systems air distance based on propagation time Tx Rx frequency MHz RSSI dBm Receiver Signal Strength Indicator Current receive level CINR dB Carrier to Interference Noise ratio Indicates the current radio link s signal quality In normal conditions CINR2 19 indicates a good signal quality Mode Current operational mode of the link o Alignment Carrier Wave transmission Used for antenna alignment No data over the radio link o Static Fixed modulation profile If you select Static you must select from a list of pre configured modulation profiles in the Modulation field o Adaptive Adaptive Bandwidth Code and Modulation The system will work on the highest modulation profile based on the CINR values of the both sides and will present the current modulation profile Estimated Throughput Mbps based on the current modulation profile o For EH 600T TDD system value is aggregated Half Duplex Page 33 EH 600T Installation Manual 3 3 3 3 1 3 3 2 Note Actual Layer 1 throughput depends on product s specs Refer to the EtherHaul Release Notes for exact specifications e Current Alarms list of currently active
16. CONTENTS 1 Introduction to the EtherHaul SYSteM sssssssssssssrssssrsssrsnnrrnn rnn rn nn nn nn 10 EST EN e Oe EE 11 E MINS e ERR MOM EE 13 Lo Feed 14 E e Ee EE 15 E Ee EE 16 2 installing the EtherHaul System ssssssssssrssarssnssrennrsnnrnnna rn ARR RANN ARR R AR RAA gt 17 AN Pre OTID DE OC shah fecal tiated ee 18 2 1 1 Physical and Environmental Reouements 18 SS ME ee REGU EE 19 22 BperHiul Packace onies e 20 Zor in E the e dE EE UE 20 Dee e E E 20 20 Preparing EE ET e 21 20 euer Eege 22 Z Nees MCG EE 23 Stach EE 23 212 OC POWER Supply NOLES EE 24 Se roundino Eeer 25 20 Proparin e ee 26 2 7 5 Removing Connectors from the EtherHaul OD 21 2 10 eeler DE POW Cr seas sobva severe os EEEE EEE R EEEE E EER 21 2 1 NEE tege Other Leier Zi ER 28 29 ANTOINE he Eeer eege 28 E Setting the ODU to Aligniment Node EE 28 29 2 Ehe EE aers 29 SIAS ISIR UPV riea UON eeose ssh TEE E aA NRA ARR 30 3 Performing Basic Setup Using the Web Based Management 31 3 1 Connecting to the ODU Using the Web Based Management 32 Ee E E 33 3 3 General Configuration Commands ccccceccccssecccceeeeceescceeeseceaeseceseseesaeseeeseseesaenes 34 SE e EE 34 e ELE 34 Ee AROWDACK E 35 Page 7 EH 600T Installation Manual GE eege 35 GG E Oy Te 35 3 4 Quick Configuration Ward 36 3 4 1 Quick Configuration Step I System sssssmsssersssrrssrrrsersrserrrerrrrerrrrrr
17. Unscrew the connector outlet portion of the All Weather shell from its ODU port Remove the cable connector from its port Connecting DC Power d Carefully screw the connector outlet portion of the All Weather shell into the PWR port Tighten the connector outlet portion securely by hand do not use tools Insert the power connector into the port The PWR LED color indicator turns red for one second then blinks green indicating that the ODU is powered on Screw the cable inlet portion 0 of the All Weather shell onto the secured connector outlet portion taking care not to twist the connecting cable Tighten the cable inlet portion securely by hand The rubber gasket insert will tighten to create a moisture proof seal do not use tools Secure the power supply cable into place using a cable tie Ensure that there is sufficient play in the cabling to allow movement of the ODU during final alignment Wait for the EtherHaul ODU to boot up about two minutes When the ODU is fully rebooted the PWR LED color indicator turns green during power up the PWR LED blinks green and the RF LED color indicator turns off indicating that the link is down Connecting Other Interfaces For each network connection perform the following steps 6 Carefully screw the connector outlet portion of the All Weather shell into the appropriate port Tighten the connector outlet portion securely by hand do not use tools Ins
18. ackage content should be examined carefully before installation When you unpack the components of the EtherHaul it is important to use care so as to avoid damaging or scratching the antenna radome e Do not touch the radome when unpacking the ODU e Do not rest the ODU face down or touch the radome It is crucial to prevent contact between the radome and other objects 2 4 Required Tools Ensure that you have the following tools with you when performing an EtherHaul installation e Standard handheld digital voltage meter DVM with probes e Philips screwdriver medium size head for grounding connection Page 20 EH 600T Installation Manual 2 5 e Flat head screwdriver medium size 5mm head for fastening the worm clamp that holds the mounting brackets Flat head screwdriver small size 2mm head for DC connector 7mm Hex socket driver e Cable ties for securing network and optional power cables e Cutter e Cable labeling Preparing for Installation The expected receive signal strength should be calculated prior to installing the link for each antenna ODU read from the DVM prior to installation based on the network link budget Calculating the expected RSSI RSSI Pix Gant1 weg LES a Attatm Gant2 Where Pi ODU s Tx Power typically 5dBm e Ganti Gain of antenna 1 typically 35dBi e Gant2 Gain of antenna 2 typically 35dBi LFS Loss of Free Space 92 45 20 Log Dxm Feuz
19. and FCC Part 15 255 e EMC EN 301 489 4 e Safety IEC 60950 e Operation EN 300 019 1 4 Class 4 1E e Storage EN 300 019 1 1 Class 1 2 e Transportation EN 300 019 1 2 Class 2 2 FCC IC Regulatory Statements This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules and IC RSS standards These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference Page 5 EH 600T Installation Manual will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Note Changes or modifications to this equipment not expressly approved by Siklu LTD or the party responsible for compliance cou
20. ctive to Startup Configuration 2 Save the configuration file for future records and backup 4 2 EtherHaul Commissioning and Acceptance Form EtherHaul Commissioning and Acceptance Form Customer Details Physical Installation Verification Local Site Remote Site Site name amp address Mount type JRoof top Roof top _ Mast Tower JMast Tower JOther JOther Page 48 EH 600T Installation Manual Clear line of sight ODU safely mounted using Siklu s LJ Yes LJ NO LJ Yes LJ NO bracket correctly installed Pole diameter according to mount Yes No LJ Yes LJ NO Specs Bracket s mounting bolts securely Yes _ No _ Yes _ No tightened Cables Fibers connections Eth1 Cat5 Eth1 Fiber JEth1 Cat5 JEth1 Fiber mark all cables connected JEth2 Cat5 JEth2 Fiber JEth2 Cat5 JEth2 Fiber JEth3 Cat5 JEth3 Fiber JEth3 Cat5 JEth3 Fiber _ Eth4 Cat5 JEth4 Fiber JEth4 Cat5 JEth4 Fiber oc Cloc Cables Fibers securely routed and Yes _ No _ Yes No fixed properly using cable ties Cables Fibers are properly Yes LJ NO LJ Yes LJ NO weatherproofed using the appropriate glands ODU DC source PoE JExternal DC PoE JExternal DC PoE model and manufacturer Measured DC power management Volts DC Volts DC reading come om om Page 49 EH 600T Installation Manual Channel width J2soMHz _ 500MHz 250MHz 500MHz JAuto JAuto
21. ctly same configuration will be copied from the local to remote system It can be found for parameters that normally requires identical configuration for both local and remote units For example Encryption configuration Matching configuration for parameters that require matching but opposite configuration For example transmit frequency where Tx local Rx remote and Rx local Tx remote Quick Configuration Wizard Use the Quick Configuration wizard to configure the basic system parameters It holds the basic minimal configuration required to start using the link The Quick Configuration wizard should be used for the initial system setup after installation For monitoring and advanced configuration please refer to the dedicated configuration pages of the Web Based Management To access the Quick Configuration wizard go to the Quick Config page Quick Configuration Step 1 System Main Radio Eth Ports System Network Services Advanced Config Statistics Help LOCAL 192 168 0 1 em H REMOTE Name EH 600T Status Link Up Name EH 600T Product Name ES System Date amp Time Date 2014 08 21 Time 16 38 15 Date 2014 06 21 Time 16 38 15 Figure 3 5 Quick Config Page Step 1 System The first section allows configuring the following parameters e Name you can give a name for each system e Date YYYY MM DD Time HH MM SS Click Next to continue Page 36 EH 600T Insta
22. enu Mode operational mode of the link o Alignment Carrier Wave transmission Used for antenna alignment No data over the radio link Note the radio link When exiting Alignment mode perform system reset to allow proper operation of Page 37 EH 600T Installation Manual 3 4 3 o Static Fixed modulation profile If you select Static you must select from a list of pre configured modulation profiles in the Modulation field o Adaptive Adaptive Bandwidth Code and Modulation The ODU will work on the highest modulation profile based on the CINR values of the both sides and will present the current modulation profile Adaptive mode is the normal and recommended mode of the radio link e Alignment Status R O field indicating that the ODU is currently in Alignment mode by configuration or by inserting DVM probes e Alignment Probe when checked the ODU will use the Alignment Cap Screw status as alignment indication when removing the screw the ODU will switch to Alignment When unchecked the ODU will not switch to alignment mode is the screw is removed Note i It is recommended to disable the Alignment Probe indication after link is installed e Transmit Asymmetry Default value is symmetric configuration 50 for Tx and Rx 50tx 50rx For an asymmetric configuration 75 25 or 90 10 Role has to be set the Master unit transmits the higher rate 75tx 25rx or 90tx 10rx and the
23. erference avoidance algorithm is implemented in order to overcome the main drawback of use of ATPC interference from other links that may degrade the radio link performance Besides setting the Target RSSI the user can also set the Target CINR that will notify the remote transmitter to increase its Tx power to maintain CINR is above the threshold set Mode of operation the local system compares the actual received RSSI to the ATPC Target RSSI If the difference in values is 2dB or higher Delta gt 2dB a message to remote transmitter will be sent asking to change its Tx power The Tx power can be changed the system s configured Tx power down to the ATPC Min Tx Power that was configured Configuration options o Checkbox to enable the ATPC operation o ATPC Target RSSI allowed values 35 to 70 dBm default 35 dBm Page 43 EH 600T Installation Manual 3 5 3 o ATPC Min Tx Power allowed values 35 to 0 dBm default 35 dBm o Min CINR allowed values 128 to 128 dB default 128 dB e Encryption checkbox to enable Encryption and field to enter the static key The EtherHaul supports 128bit and 256bit AES encryption with Static key This means that the encryption key 32 characters long for AES 128bit or 64 characters long for AES 256bit must be inserted manually into both ends of the link If there is an encryption mismatch traffic does not go over the link Encryption is a licensed feature that requires license f
24. ert the RJ45 or SFP connector into the port Screw the cable inlet portion 0 of the All Weather shell onto the secured top portion taking care not to twist the connecting cable Tighten the bottom portion securely by hand The rubber gasket insert tightens to create a moisture proof seal do not use tools Page 27 EH 600T Installation Manual 9 Secure the network connection cable into place using a cable tie Ensure that there is sufficient play in the cabling to allow movement of the ODU during final alignment 2 8 System LEDs PWR Power Green Power OK Blink Green Device boot Red Power Failure eege EE Off No Power Green Link Up 3 Blink Green Device boot Orange Alignment Mode ee Stee eee a Off Link Down ETH1 2 3 Green Link 1G Blink Green 1G activity Off No Link Carrier 2 9 Aligning the Antenna The ODU antenna must be aligned on both local and remote ODUs You must first perform coarse alignment on each ODU followed by fine alignment Accurate alignment of the ODU is critical for achieving the strongest possible receive signal To perform antenna alignment the ODU must be in Alignment mode The ODU has three modes of operation e Alignment Carrier Wave transmission Used for antenna alignment e Adaptive Operational mode used with adaptive bandwidth code and modulation e Static Operational mode used with a fixed modulation pr
25. f the grounding cable to the ground outlet on the left side of the ODU using the grounding cable lug 2 Tighten the lug securely in place 3 Connect the opposite end of the grounding cable to the earth connection typically located on the mounting pole If the earth connection is out of reach of the grounding cable install an alternative cable To make a protective earth connection use the grounding point located on the System ODU using a minimum amount of 16AWG grounding cable or according to local electrical code It is recommended to use Lightning Surge Protector on every Ethernet cable to protect the indoor networking equipment The Lightning Surge Arrestor should be installed indoor next to the cable s point of entry and should be properly grounded ii a 1 L Grounded to pole Make sure to remove paint to assure good ground connectivity Shielded Ethernet Cable To Indoor PoE Roof Outdoor Ground Shielded Ethernet Cable From roof Verify grounding continuity between outdoor and indoor ground Surge Protector Indoor Ground e Figure 2 4 Grounding Scheme Page 25 EH 600T Installation Manual 2 1 4 Preparing the Cables Before inserting a cable connector into the ODU you must first enclose the cable connector in a protective All Weather shell Four sets of All Weather shells are provided with the ODU for the ODU interfaces 1 Cable Inlet Portion 3 Connector Outlet Portion
26. ge 44 EH 600T Installation Manual 3 5 4 3 5 5 This section allows configuring the following parameters RF Loopback checkbox to enable the internal RF loopback set the timeout for clearing the loopback in seconds and select the modulation the ODU will be tested at Note that it will take the ODU to stabilize after loopback up to 3 minutes so set the loopback timeout accordingly recommended 600 seconds Mute remote transmitter first to avoid interference with the loopback operation Loopback is done with MAC addresses swap Refer to the Diagnostics chapter of this manual for detailed description of the system s loopbacks e Mute checkbox to mute the transmitter with timeout in seconds When muted the ODU will not transmit Modulation Table ae Frequency nodutarion subehannek Repeticons FEC Rate lee gebiet SEH SES Advanced Settings Maintenance Modulation Table Modulation Table Statistics Figure 3 12 Radio Page Modulation Table The modulation table presents the available modulation profiles The radio can be configured only to one of the profiles available in the table e CINR Low Lower threshold for stepping down in modulation profile Adaptive Mode e CINR High Upper threshold for stepping up in modulation profile Adaptive Mode Note that different modulation tables may apply according to product used the frequency channel used and ARQ status The modulation profiles and threshold
27. he mounting bracket should be installed up side down In this case relocate the 3 mounting bolts from the top of the ODU to the opposite 3 vacant holes and install the ODU so the connectors will still face downwards 3 Mount the ODU on a fixed reinforced steel mounting pole with 2 4 inches diameter 4 In order to allow free movement during alignment unlock the Elevation and Azimuth Lock Bolts and position the bracket at O degrees 5 Fasten the worm clamp to secure the bracket to the mounting pole while the ODU is pointing to remote site coarse alignment Use worm clamp at size that will allow firm grip to the pole Page 22 EH 600T Installation Manual Note You can use second worm clamp for additional safety In case just one worm clamp is used install it on the top position 6 Note that ODUs are shipped in Vertical polarization Installation at Horizontal polarization TBD Contact Siklu for details yi I 2 1 Connecting the Cables 1 Electrical Ground Point GND 5 Ethernet RJ45 Eth 3 PSE 2 Power Connector Interface PWR 6 Reset Button press for more than 8 seconds to restore factory defaults 3 Ethernet RJ45 Eth 1 PoE 7 Alignment Cap Screw and DVM probe A Ethernet RJ45 Eth 2 8 Second DVM probe Figure 2 2 EtherHaul 600T Connection Panel Details 2 7 1 Power Options Note Two different HW options are available DC or 802 3at PoE ordering options PoE system sh
28. he powered device PD should not exceed 40 meter even if the PSE option is disabled e You should use shielded outdoor Cat5e cables terminated with metallic RJ45 connectors e n order to protect indoor equipment you must install surge protection circuits on all copper cables on their entrance to the building e Install the EtherHaul ODU in a location where proper electrical outdoor grounding is readily available Typically the grounding connection is attached directly to the mounting pole If not already present then suitable structure to earth grounding connections must be created before installation Ground the ODU using a minimum quantity of 16AWG grounding cable or according to local electrical code Improper electrical grounding can result in excessive electromagnetic interference or Caution electrical discharge S Siklu will not be held responsible for any malfunction or damage in the event that the ODU is not properly grounded Page 19 EH 600T Installation Manual 2 2 EtherHaul Package Content An EtherHaul link consists of two ODUs and two mounting assemblies The EtherHaul packages include the following components EtherHaul 600T ODU EtherHaul 600T ODU 1 integrated antenna Connecting cable All 4 Weather shells Unit grounding cable 90 1 cm EtherHaul 600T EtherHaul 600T mounting 1 assembly mounting DC cable terminal block 1 connector assembly 2 3 Unpacking the EtherHaul The EtherHaul p
29. herHaul s installation procedure and requirements 1 Pole mount installation 2 ODU installation 3 Weatherproofing the cables 4 Cables installation 5 Grounding RF Link Test This inspection verifies the RF link status 1 RFLED is green 2 Management CLI indication RF Operational Up 3 Receive Signal Strength Indication RSSI achieved in Alignment mode is within 4dB of the expected value 4 Carrier to Interference Noise Ratio CINR is 19 or higher 5 Highest modulation achieved 6 Link configuration is in accordance with plan requirements Link Errors Test This inspection verifies frame loss free operation of the radio link Page 47 EH 600T Installation Manual 1 No ARQ losses on the RF Statistics counters 4 1 4 Ethernet Services Test This inspection verifies correct Ethernet services flow and error free operation 1 Connect PCs on both ends of the link and use software based utilities to test for packet loss 2 If available connect a packet analyzer to the GbE port and verify that no packets are lost 4 1 5 Management Verification This inspection verifies proper management of the link 1 Verify correct management CLI connection to both local and remote ODUs 2 Verify management access from remote NMS stations 4 1 6 Recording ODU Configuration Perform the following steps after the EtherHaul ODU is commissioned and accepted 1 Copy the Running Configuration currently a
30. in turns till optimal alignment 6 Once the optimum position achieved tighten the azimuth and elevation lock bolts on first ODU 7 Use the DVM to verify that the received signal level has not degraded during locking 8 Repeat steps 5 6 on the second ODU Antenna alignment is now complete Page 29 EH 600T Installation Manual 2 10 Link Up Verification 1 Disconnect the DVM and re insert the Alignment Cap Screw and lock it 2 Reboot both ODUs by shortly pressing the ODU Reset Button or alternatively disconnect reconnect the power 3 This action will returns the ODU to Adaptive Mode ODU s default operational mode Following this action and after the ODU has finished rebooting the RF LED color indicator on both ODUs will turn Green indicating that the radio link is up Note If you will not re insert and lock the Alignment Cap Screw the link will not come up after the reboot The EtherHaul link can now pass traffic and management between the ports and over the radio link Use the Web based management or Command Line Interface for radio link configuration and monitoring Page 30 EH 600T Installation Manual Performing Basic Setup Using the Web Based Management This chapter describes how to perform basic setup using the web based management The scope of this installation manual is basic setup and monitoring of the radio link e For full configuration and maintenance procedures refer to the Ethe
31. kable hypertext links that enable immediate access to referenced objects Document References Command Input Monospace text is used to help delineate command line user input or text displayed in a command window Page 4 EH 600T Installation Manual Safety and Regulatory Notices The following are mandatory notices for installation and operation of EtherHaul Wireless Backhaul Link Indications appearing here are required by the designated government and regulatory agencies for purposes of safety and compliance General Do not install or operate this System in the presence of flammable gases or fumes Operating any electrical instrument in such an environment is a safety hazard European Commission This product has been designed to comply with CE markings in accordance with the requirements of European Directive 1995 5 EC This product has been designed to comply with the requirements of European Directives This equipment must be permanently earthed for protection and functional purposes To make a protective earth connection use the grounding point located on the System ODU using a minimum amount of 16AWG grounding cable or according to local electrical code This apparatus is intended to be accessible only to authorized personnel Failure to prevent access by unauthorized personnel will invalidate any approval given to this apparatus This product is in full compliance with the following standards RF EN 302 217 3 1 3 1 V B
32. ld void the user s authority to operate the Caution equipment Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and wherever applicable are licensed by the appropriate government regulatory authorities Failure to do so may void the product warranty and may expose the end user or the service provider to legal and financial liabilities Siklu LTD and its resellers or distributors are not liable for injury damage or violation of regulations associated with the installation of outdoor units or antennas Prudence Les unit s ext rieures et les antennes doivent tre install s que par des professionnels exp riment s d installation qui sont familiers avec les norms locales et les codes de s curit et si applicable sont agr es par les autorit s gouvernementales de r glementation comp tents Ne pas le faire peut annuler la garantie du produit et peuvent exposer l utilisateur final ou le fournisseur de services d obligations juridiques et financiers Revendeurs ou distributeurs de ces quipements ne sont pas responsables des blessures des dommages ou violation des r glements li s a l installation des unit s ext rieures ou des antennes L installateur doit configurer le niveau de puissance de sortie des antennes conform ment aux r glementations nationales et le type d antenne Page 6 EH 600T Installation Manual TABLE OF
33. le for the control plane and the antenna alignment Antenna Siklu s self designed 1ft innovative antenna as well as 2ft antenna option for longer range higher availability Page 13 EH 600T Installation Manual Ja 4 Memory controller Upconver ter A Control Peripherals processor AFE PLL VCO RX TX Switch Downconver ter lt Modem amp Packet Proc Ethernet PHY1 MAC 1 H RFIC Network Processor RF Controller PoE Eu DC DC Baseband ASIC Figure 1 2 EH 600T Functional Block Diagram 1 3 Technical Specifications For detailed technical specifications please refer to the datasheet For detailed supported features list please refer to the product s release notes EtherHaul 600T Technology and frequency e TDD 57 66GHz e Hitless adaptive bandwidth coding and modulation boosting system Adaptive modulation gain by 25dB Up to 1000Mbps aggregated with asymmetric downlink uplink rate Over the air throughput j BEES l S EE support Typical link distance e Upto 400m e 3x100 1000 base T or 2x100 1000 base T 1x1000 base F SFP PoE IEEE 802 3at Power options Direct Telco DC 36 57VDC PSE IEEE 802 3af
34. less errorless Adaptive Bandwidth Coding and Modulation ABCM for a large dynamic range e Configurable center frequency across the entire band Page 11 EH 600T Installation Manual Carrier Ethernet Inside e Integrated Gigabit Ethernet switch e Advanced bandwidth aware QoS capabilities e MEF compliant services and QoS Advanced service management OAM and SLA assurance support e SyncE IEEE 1588TC and optimized transport of IEEE 1588 Ring mesh and daisy chain topologies for carrier grade availability and resiliency Standard based for seamless integration into existing networks and multi vendor interoperability e Multi vendor interoperability approved Carrier Grade e CLI SNMP and web based local and remote management Extremely high reliability with very high MTBF e Designed for ultra low MTTR without the need for antenna realignment Green Design e Zero footprint all outdoor extremely light weight e low power consumption e IEEE 802 3at complaint Power over Ethernet Quick and Easy Installation e Rapid and flexible deployment e Precise antenna alignment e Minimal site preparation Security e Advanced AES encryption and security Narrow and secure beam width Adaptive Bandwidth Coding and Modulation The EtherHaul family implements hitless errorless adaptive bandwidth coding and modulation adjustment to optimize the over the air transmission and prevent weather related fading from disrupting traffic on the link The
35. llation Manual 3 4 2 Quick Configuration Step 2 Radio CA eee Tx Frequency 58375 MHz kal Copy to Remote gt gt 58375 Channel Bandwidth MHz RI Lv 500 X lt 5 5 Radio Tx Power dBm 5 Alignment Status Inactive Inactive Alignment Probe Li v S QAM64 4 10 5 sl QAM64 4 1 0 5 sl demm 87 Adaptive O Alignment Static Copy to Remote gt gt amp Adaptive V Alignment Static Transmit 7 symmetiy 50TX 50RX y Copy to Remote gt gt 50TX 50RX y Back Next Figure 3 6 Quick Config Page Step 2 Radio This section allows configuring the following parameters Channel Bandwidth MHz 250 or SOOMHz default is 500 MHz Note 250MHz support depends on product s specs Tx Frequency MHz transmit frequency Rx Frequency MHz R O field updated based on Tx frequency Tx Power dBm ODU s transmit power Default is the max power based on product s specs Minimum configurable Tx power is 35dBm note that actual minimum Tx power is based on product s specs Note threshold Adjust Tx Power so the RSSI at the remote end will not exceed 35dBm overload The Tx power value sets the transmit power for the highest modulation profile In case lower modulation profile s has higher max Tx power based on product s specs the Tx power will be increased automatically without indication in RF configuration m
36. ne by service personnel who are properly trained and certified to carry out such activities L installation et l entretien de la liaison EtherHaul ne doivent tre effectu s par du personnel de service qui sont form s et accr dit s pour mener bien ces activit s Caution It is the responsibility of the installer to insure that when using the outdoor antenna kits in the United States or where FCC rules apply only those antennas certified with the product are used The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15 204 Avertissement Il est de la responsabilit de l installateur de s assurer que lorsque vous utilisez les kits d antennes ext rieures seules les antennes certifi s avec le produit sont utilis s L utilisation d une antenne autre que ceux qui sont certifi s avec le produit est express ment interdite par la r glementation FCC partie 47 CFR 15 204 et IC normes RSS This equipment should be installed and operated with a minimum distance of 50 cm between the radiator and your body Cet quipement doit tre install et utilis une distance minimale de 50 cm entre le radiateur et votre corps Preparing the Site Carefully select and prepare each EtherHaul ODU site to make device installation and configuration as simple and trouble free as possible During site selection and preparation always consider the long term needs of b
37. ned meaning the IP is not associated with specific VLAN Click the Trash icon to clear an IP Note you cannot clear the IP address you used to log in to the system e Default Gateway e SNMP Managers Up to five managers that will receive SNMP traps can be configured SNMPv2c or SNMPv3 o Index 1 5 o IP Address Destination IP Address o UDP Port port number for sending traps o Security Name community o SNMP Ver SNMP version SNMPv2c or SNMPv3 o Engine ID Used for SNMPv3 Click Apply to execute the configuration changes or Back to return to previous section Radio Page The radio link parameters and radio link monitoring are managed in the Radio page This chapter includes the following topics e Settings e Advanced Settings Maintenance e Modulation Table e Statistics Page 40 EH 600T Installation Manual 3 5 1 Settings Tx Frequency MHz 58375 M Copy to Remote gt gt 58375 v Advanced Settings Tx Power dBm 5 5 Maintenance RSSI dBm 41 WE ma 39 WE T 100 35 100 35 Modulation Table I BEE CINR dB 23 Gt ap 23 W qT 0 25 0 25 Statistics Alignment Status Inactive Inactive Alignment Probe MI Ba Mode Transmit Asymmetry QAM64 4 10 5 v Adaptive Alignment Static 50TX 50RX sl Copy to Remote gt gt Copy to Remote gt gt QAM64 4 1 DE sl Adaptive Alignment Static 50TX 50RX v
38. ofile ODUs are shipped from the factory in Adaptive mode 2 9 1 Setting the ODU to Alignment Mode Switch the EtherHaul ODUs to Alignment mode by inserting the DVM probes into the DVM probes at the top of the ODU For this purpose you will have to remove the Page 28 EH 600T Installation Manual Alignment Cap Screw secured with metal strip The RF LED color indicator turns orange indicating the ODU is in Alignment mode The ODU remains in Alignment mode even if the DVM probes are ejected until the Alignment Cap Screw is inserted and locked and ODU is rebooted 2 9 2 Performing the Alignment 1 Verify that both ODUs are in Alignment Mode 2 Verify that the Elevation 1 and Azimuth 5 Lock Bolts are unlocked and positioned at 0 degrees Coarse Alignment Azimuth Only 3 Verify visually that the ODU is pointing to remote site Optimize the coarse alignment by turning the mounting bracket Once optimum achieved fasten the worm clamp to secure the bracket to the mounting pole Fine Alignment 4 Read the receive level RSSI using the DVM The voltage reading will be between 0 to 1Vdc indicating the RSSI in dBms for example 0 45V 45dBm Voltage reading on the RSSI will be available 1 minute after switching the ODU to Alignment Mode 5 Perform fine Azimuth and Elevation alignment using the fine adjustment bolts identifying the main lobe until the expected receive level is achieved within 4dB Align the ODUs
39. or operation Before configuring it verify that license is available and enable the encryption license component e Role Determines whether the ODU functions as a master or slave In a link one side must be set to Master and the other side must be set to Slave required for link synchronization Default value is Auto meaning the role is set automatically by the link Manually setting the Role is necessary only for asymmetric configurations Link ID unique Tx and Rx Link IDs for links installed on the same site to avoid locking on the wrong transmitter Link IDs must be identical on both ends for the link to be operational e ARQ checkbox to enable the mode and field to view the current status The ARQ Automatic Repeat Request is an algorithm that uses selective repeat retransmission to eliminate radio BER The default mode is Enabled When both sides are enabled and radio link is up ARQ status will be Established Disabling the ARQ mode is not recommended as it may result in radio BER e Lowest Modulation Lowest modulation profile When modulation drops below this threshold radio link will be down It is used to limit the minimal modulation profile of the link Default is QPSK 1 40 5 lowest available Maintenance Settings RF Loopback Timeout sec D Modulation Advanced Settings Mute Timeout sec 60 Maintenance Modulation Table Statistics Figure 3 11 Radio Page Maintenance Pa
40. oth your network and your applications Physical and Environmental Requirements Each EtherHaul ODU site should adhere to the following requirements e There must be a clear unobstructed line of sight between ODU e The EtherHaul ODU should be mounted on a fixed stable permanent structure A reinforced steel mounting pole is required with a diameter measuring from 2 4 inches Caution Do not mount the EtherHaul device on a structure that is temporary or easily moved Doing so may result in poor service or equipment damage e You must mount the EtherHaul ODU in a site that is easily accessible to authorized personnel and only authorized personnel Page 18 EH 600T Installation Manual Operating temperature between 45 and 55 C Relative humidity 0 to 100 Maximum altitude 4 500m Ingress Protection rating IP67 2 1 2 Cabling Requirements e Ensure that your power connection cable matches the EtherHaul power connector pin outs e Install the EtherHaul ODU where network connections and optional power cabling are ready for operation and easily accessible All cabling connected to the ODU should be outdoor grade with UV protection e DC input Use a two wire cable 14 18 AWG to connect the power supply to the ODU e PoE input Connect Eternet cable to Eth1 PSE Output The voltage output at the PSE port is following the voltage at the PoE input port The cable length from the PSE port ETH 3 to t
41. ould be powered by connecting the PoE to Ethernet RJ45 Eth 1 DC connector connect ONLY the and Page 23 EH 600T Installation Manual Figure 2 3 DC Connector To power up the EtherHaul using PoE connect the cable to Eth 1 2 1 2 DC Power Supply Notes The DC power input range of the ODU is 36 57 VDC The DC supply should be limited to two ampere to avoid surges and possible damage to the ODU For that use limited power supply or circuit breaker fast blow fuse The circuit breaker is the disconnecting device and should be readily accessible When connecting the ODU to a MAINS DC distribution system use a two ampere circuit breaker to enable the central DC system to isolate the ODU in an emergency case Use one poly circuit breaker and should connect it on the live voltage or The other poly should be grounded Connect the circuit breaker to the or live voltage The DC input is floating so either or can be connected to the GND on the power supply side For the sake of consistency with other systems Siklu recommends that you connect the to the GND Use a two wire cable 14 18 AWG to connect the power supply to the ODU On the ODU DC terminal connect only the and wires Do not connect to the ODU s GND input Caution S Disconnect all power cables before service Page 24 EH 600T Installation Manual 2 7 3 Grounding the EtherHaul 1 Connect one end o
42. rHaul Operation Administration and Maintenance Manual e The EtherHaul Operation Administration and Maintenance Manual also details the configuration monitoring and maintenance procedures using the Command Line Interface This chapter includes the following topics e Connecting to the ODU using the Web Based Management e Main Page e General Configuration Commands e Quick Configuration Wizard e Radio Page e Default Bridge Configuration e Applying and Saving Configuration Changes Page 31 EH 600T Installation Manual 3 1 Connecting to the ODU Using the Web Based Management 1 Launch an Internet Browser and enter https followed by the ODU s IP address The ODU s default IP address is 192 168 0 1 A O Q https 192 168 0 1 DrX Figure 3 1 Launching the Web Based Management 2 When prompted enter the username and password Default admin and admin Windows Security The server 192 168 1 183 at main requires a username and password ps er name ww Password Password Remember my credentials Figure 3 2 Entering Username and Password 3 Once loaded the Web Based Management Main page is displayed Quick Config Radio Eth Ports System Network Services Advanced Config Statistics Help LOCAL 192 168 0 1 emm a REMOTE Product EH 600T Product EH 600T Status Link Up Name EH 600T Name EH 600T Link Length m 0
43. ration Running Configuration In order to save the applied configuration changes click Save Configuration so changes will be saved to the startup configuration If changes are not saved to the startup configuration they will be lost the next time the system resets Save Configuration button are available for local and remote systems Rollback A safety measure that allows recovering from system configuration changes that caused loss of communication When Rollback is used a timer runs and restarts whenever a management or CLI command is entered In the event that no command is entered within the timeout period the system automatically resets and comes up with the saved startup configuration A Rollback timeout is especially recommended when configuring remote elements that are being managed over the link Rollback is activated for both local and remote systems Reset Separate buttons for local and remote reset The system will reset and come up after initialization 120 seconds Note that any unsaved changes will be lost Copy To Remote You can find the Copy To Remote button next to some configuration parameters or sections This function copies configuration to remote system based on the changes on the local system Copy to Remote gt gt Figure 3 4 Copy To Remote icon Page 35 EH 600T Installation Manual 3 4 3 4 1 Matching configuration may be of two types Identical configuration exa
44. rm factor the EtherHaul products are also environmentally friendly boasting a small system and antenna footprint with especially low power consumption The EtherHaul systems are High capacity Gigabit Ethernet backhaul with advanced networking capabilities at the lowest TCO in the industry EtherHaul enables mobile operators to profitably and reliably provide data intensive services Provided by Siklu the pioneer in silicon based mm waves backhaul systems EtherHaul systems are the perfect choice for future proof investment Main Features Siklu s EtherHaul wireless backhaul radio link operates in the new V band and E band spectrum which provides clear technological and economic advantages over the existing lower frequency bands Taking advantage of the new spectrum the EtherHaul enables easy migration to support Gigabit throughput enabling operators to enhance bandwidth capacity on a pay as you grow basis Supporting point to point daisy chain ring and mesh configurations the EtherHaul system offers carrier class availability and services The following are some of the main features of the EtherHaul availability of features depends on platform All Outdoor Packet Radio e Operates in the unlicensed 57 64 GHz V band Upto 1 Gbps throughput e Asymmetric capacity configuration e High gain narrow beam width directional antenna e Low latency Highest Spectral Efficiency e 250 MHz 500 MHz channel bandwidth e Advanced hit
45. rrerrrrrrrrrra 36 3 4 2 Quick Contieuration Step 2 Te e E 37 3 4 3 Quick Configuration Step 3 Eth Rote 38 3 4 4 Quick Configuration Step 4 Network 39 GG DE 40 E ie Ha EE 41 SG NOVA C COS E 43 BO EREM 44 Ds lee E 45 E E e 45 30 EE EE 46 4 Commissioning and Acceptance Procedure ccccssccesseeeeseseeneseeneneees 47 4 1 Installation Verification and Iespng 47 4 1 1 Physical Installation Verification ssssssssrrssersssrerserrrerrerserrrsrrrrerrrrrrrrerrrr rss rrr rss 47 A REENE E E 47 Adc dS EMEEN S PCS ecsttietiews rican ee eee 47 e E Ethene SCL VICES RE 48 e Manasemeont e tee OD EE 48 A106 JRecordine OD U EE eet 48 4 2 EtherHaul Commissioning and Acceptance Form 48 Page 8 EH 600T Installation Manual TABLE OF FIGURES Figure 1 1 Hitless Adaptive Bandwidth Coding and Modulation ssssresssersrsrrrrrserrrrrerrn gt 13 Figure 1 2 EH 600T Functional Block Diagram sssserssssersssserrrrerrrrrerrrrsrrrrrrrrrrrrrrrrrrrrrrr rr rna 14 Figure 2 1 EtherHaul 600T Mounting Bracket 22 Figure 2 2 EtherHaul 600T Connection Panel Deals 23 Fore DEC ere EE 24 Pie ure 2 4 ee EE EE 25 Figure 2 5 All Weather Connecting Cable Shell Assembly osmemsssssssserssrsrrrrrrrrerrerrrrrerrrrrrrrr gt 26 Figure 3 1 Launching the Web Based Management 32 Figure 3 2 Entering Username and Password ccccccccccseeeeeceeeeeceseesecceaeeeeeeaeeseeeesaeseeees 32 Figure 3 3 Web Based
46. s are optimized and should not be modified can be configured via CLI only after consulting Siklu support Statistics Radio link s performance can be monitored using the advanced statistics counters Refer to the Statistics chapter of the EtherHaul Operation Administration and Maintenance Manual for detailed description of the system s statistics Page 45 EH 600T Installation Manual 3 6 Default Bridge Configuration The default system s configuration is IEEE 802 1d Transparent Bridge In this mode all traffic both tagged and untagged is transparently forwarded between all ports and over the radio Page 46 EH 600T Installation Manual 4 1 4 1 1 4 1 2 4 1 3 Commissioning and Acceptance Procedure This chapter presents the recommended commissioning and acceptance procedure to be performed following the installation of each EtherHaul radio link The commissioning and acceptance procedure verifies the correct installation and the proper safe and robust operation of the EtherHaul RF link This chapter includes the following topics e Installation Verification and Testing e EtherHaul Commissioning and Aceptance Form Installation Verification and Testing Inspect the following components and confirm their adherence to requirements that are detailed in the accompanying checklist Physical Installation Verification This inspection verifies the physical installation of the ODU in accordance with the Et
47. structions how to use the product s features refer to the EtherHaul Operation Administration and Maintenance Manual Features and functionality described in this document may be available for specific Note product models or starting from specific SW version A Please review the individual product s release notes to verify if a specific feature is supported in the product you use Applicable Products and Releases e V Band o EH 600T minimum SW release 6 0 0 Audience This document assumes a working knowledge of wireless backhaul platforms and their operating environments This document is intended for use by all persons who are involved in planning installing configuring and using the EtherHaul system Conventions The following conventions are used in this document in order to make locating reading and using information easier Special Attention Hint Informs you of a helpful optional activity that may be performed at the current operating stage d Note Provides important and useful information or describes an activity or situation that may or will interrupt normal operation of the EtherHaul system one of its components or the network Page 3 EH 600T Installation Manual Caution Describes an activity or situation that requires special attention or warning Text Conventions Italicized text is used to reference sections or chapters in this document In many cases references use clic
48. t RSSI 35 Min Tx Power 35 Min CINR 128 Advanced Settings E d J Static key 92E3C28020570998E74B41C06A58BB4C Static key 92E3C28020570998E74B41C06A58BB4C nc on de Copy to Remote gt gt Maintenance Role Auto KA Auto v Modulation Table Link ID T 0 Rx 10 Tx 0 Rx 10 Statistics Automatic F 5 RENERE Rennes Vi Status Established d Status Established Lowest P Modulation QPSK 1 40 5 VI QPSK1405 V Figure 3 10 Radio Page Advanced Settings This section allows configuring the following parameters e Long Range Mode checkbox to enable extended range mode e Normal links from 0 to 750m e Long links from 0 to 1000m e ATPC Automatic Transmit Power Control adjusts transmitter output power of the local system based on the varying signal level at the remote receiver ATPC allows the transmitter to operate at less than maximum power for most of the time and when fading conditions occur transmit power will be increased as needed until the maximum configured value is reached ATPC messages are carried over the radio over radio communication channel The purpose of ATPC is a to reduce interference to other radios operation in the same channel band and to allow better frequency reuse and b to reduce transmitter power consumption and prolong system s components life ATPC is supplementary to adaptive modulation and works before adaptive modulation changes modulation profiles Int
49. ultiple ports enable also colocation installation and leveraging the infrastructure for additional fixed services delivery The EtherHaul is fast simple and inexpensive to deploy EtherHaul as the ideal solution for mobile backhaul and business services delivery features e Field proven technology e Reduced TCO and fast ROI All outdoor invisible footprint o Small and light o Quick and easy to install e Spectral efficient o Wide range of frequencies o TDD modulation with seamless delay and jitter o Hitless Adaptive Bandwidth Coding and Modulation for high availability Advanced layer 2 features o MEF compliant services and QoS o VLAN amp Provider Bridge with 16K jumbo frames support Clear separation between multiple services with QoS Enables QoS aware MPLS services delivery o SLA assurance e Advanced AES encryption for secured street level deployments Page 10 1 1 EH 600T Installation Manual Highly scalable the EtherHaul products are software upgradable to support future Layer 2 5 3 networking and routing capabilities as networks evolve to flat IP topologies The EtherHaul products features advanced adaptive modulation bandwidth and coding allowing operators to maintain prioritize and verify QoS in all weather conditions while achieving maximum up to 99 999 link availability for prioritized services such as voice signaling and Sync Offering easy and low cost all outdoor installation and a small fo
Download Pdf Manuals
Related Search
Related Contents
GE JVM152J User's Manual Expert Conclusion + - TELE NZXT Avatar S Notices Séries FM-TM-SM-KM SPECIFICATIONS EQUIPMENT P3 International P8315 User's Manual manuel d`instructions manual de instrucciones owner`s Copyright © All rights reserved.
Failed to retrieve file