SP10 – User's Manual
Contents
1. 6 Run SeaConfigurator Windows Start Programs SEA Configurator gt Configurator Connect your SP10 and your PC using a USB cable which is a part of the package USB connector B is located under the small square cover on SP10 see the picture When configuring SP10 with a USB cable SP10 must be connected to the power supply Load the configuration from SP10 by clicking the From station Enter your phone number and name on the User List 7 Modified configuration must be written to SP10 Click the To station If you leave the USB cable connected you can monitor the current state of SP10 inputs outputs and status 8 Digital inputs signals to SP10 are connected to terminals X1 to X9 and digital outputs signals out of SP10 are connected to terminals Y1 to Y8 Schematics of these Signals are listed in the Hardware section In the event of any change on any input SP10 can send to your mobile phone the SMS message in the form as Input1 is closed the text depends on SP10 configuration 4 Technical specifications Parameter eo Unit Width ea e GSM antenna Dimensions Depth between DIN Saaf a Vcc 8 30 Voc a a A Supply Average Pec 2 5 wW eT consumption Digital inputs igital i Voltage log IVinI 12 30 V DC H any polanty oebe b NA ef Current ty a VEV adada A Number J o S S 8 S h Digital Voltage DC Voume Cd Cd W outputs DC Voltage AC a2. Low credit on prepaid SIM card Prepaid SIM card is no longer valid because credit was not paid for long time Usually for more than a year Other reason SIM card has not active GPRS data GSM SP10 User s Manual EN v1 07 2014 05 07 Check power supply Test the SIM card in your mobile phone Check the credit on prepaid SIM card contact your operator if necessary Cancel all phone calls redirection Check the connection of GSM antenna Check the GSM signal level in the place where is located GSM antenna for SP10 Use your mobile phone with SIM card from SP10 Signal level has to be at least two bars Check the credit on prepaid SIM card contact your operator if necessary Contact your GSM mobile phone operator if you have any problem with SIM card in your mobile phone Test the SIM card in your mobile phone Sending receiving SMS voice call data call Check the SCA center setting on SIM card and in SP10 configuration Try to identify the cause of problem using LED diodes Contact your mobile operator to be sure GPRS data tariff is active for SIM card in SP10 CE 10 Frequently Asked Questions 1 What is necessary to use SP10 successfully e SIM card capable to send and receive SMS messages from a standard mobile phone and voice data call incoming and outgoing as well Please test all these functions in your mobile phone It s important to solve all possible problems be
3. O Warning Its highly recommended to use the extra power supply for SP10 power galvanically separated from the power supply for input and output external circuitry especially when I O have long wires that may be noisy page 1 of 4 5 1 Digital inputs X Digital inputs SP10 input signals are labeled X1 to X9 The COM terminal is common for all digital inputs The figure shows an example of the connection of external circuits and internal wiring of input X1 same for all digital inputs The polarity does not matter COM can be connected either to plus or to minus External exema o f com x2 xa xe m xi xa xs x7 xo At 8 to 30 V DC SP10 inputs Internal wiring i of input X1 3k9 O X1 A A N A A O F E O COM 5 2 Analog Input A SP10 has 1 analog input A1 which is connected to the input terminals labeled Ai A1 Analog input can be configured for measuring of voltage 0 to 10Vpc current 0 to 20mA or temperature using temperature sensors KTY81 210 Pt100 Pt1000 SP10 Analog input OWWWWwWw ory Analog input Input configuration for i A voltage 0 to 10VDC current 0 to 20mA Temperature sensor KTY 81 Pt100 Pt1000 nus 9 A K A WB A com x2 x4 m The measured values can be converted to user units For example the measured current from 4 to 20 mA can be displayed as the pressure of 0 5 MPa see the configuration progra
4. O dW AC Curen DC Hove 100 m Current AC Tourac 0m Number J Jo o S S r y Measured value analog input configurable for voltage current temperature measuring with calculation into users unit 0 to 10V 0 to 20mA input resistance 75Q temperature sensors KTY 50 to 150 C Analog Pt100 100 to 300 C input Al Pt1000 100 to 300 C Voltage maximum p y Current f maximum 5 mA Input voltage e e Input current waa fom f S E Resolution hn he a ee bits GSM module 850 900 1800 1900 MHz MicroSD card Temperature Operating ty P20 SC Rel humidity Operating on aa n aa SP10 is designed to be mounted into a cabinet with IP44 or better 5 Hardware GSM antenna HOSES COM X2 DEEE DE DEAE REA SP9 under the top cover 4 Input status 5 6 LED indication 7 8 GSM SP10 PWR SP10 status GSM LED indication BERR SEA i OUT Y eve 1 2 Output status www SEApraha cz i LED indication SMS PROCESSOR SIM card Connector reader tor expansion board or unit I E Button MicroSD Card reader amp 30V vs cscs ve 0c A A A A A A ous HAJARE Terminals A1 A1 analog intput voltage input 0 to 10Vpc connect terminal A1 to higher potential analog input 0 to 20 mA connect terminal A1 to higher potential temperature sensor KTY81 210 polarity does not matter
5. debugging information Y cmd B alert A alarm Q reset P pulse N not freezing temperature Number regulation function SP10 needs a MicroSD card formatted as FAT16 or FAT32 with directory LOGGER in the root directory C LOGGER Warning Check if the MicroSD card is formatted as FAT16 or FAT32 and contains directory LOGGER in the root before insertion into SP10 5 6 Backup battery SP10 is equipped with an internal Li Ion battery so it can operate without connection to the power supply When long time operation on the battery is needed so called Power saving mode can be activated in configuration in which SP10 disconnects itself during several minutes from GSM network to minimize the power consumption SP10 is awakened by an event on specified digital or analog inputs or after specified time period This cycle repeats until the power supply is restored or special SMS which cancels the power saving mode is received 6 Remote Control 6 1 SMS Message control SP10 is controlled via SMS messages of GSM network Command SMS messages are in form lt PASSWORD gt lt COMMAND gt lt RETURN COMMAND gt page 2 of 4 Example 1234 STATE 1234 DOUT1 ON be returned 1234 DOUT8 PULSE NOBACK SP10 pulse on output8 will be generated no confirmation message will be sent back SP10 returns an SMS containing status SP10 output1 will be switched on Confirmation SMS will It
6. 3 1 Check for updates GSM SP10 User s Manual EN v1 07 2014 05 07 PIN Personal Identification Number usually four digits number Only persons with knowledge of PIN can operate a SIM card in case the PIN usage on a SIM card was activated Usage of the PIN can be deactivated Insert the SIM card to your mobile phone and follow the instruction in the mobile phone manual Usually the PIN usage can be deactivated in Menu gt Security gt PIN ACCESS CODE Password for SMS commands configuration and monitoring of SP10 accepts only SMS with a valid access code The password is requested also for connection of SP10 via USB cable or remotely via data connection of GSM network Factory setting of access code is 1234 EVENT level change in case of digital input zone change in case of analog inputs SP10 can react on EVENTS by several ACTIONS if it is setup this way SP10 can send SMS messages on selected phone numbers and or to make voice calls on selected phone numbers ACTION one voice call or one SMS to one user Any EVENT can contain several ACTIONS COMMAND is sent using SMS to device or is possible to caused it as an ACTION in case of EVENT This type of command is called INTERNAL COMMAND and has the same rules as COMMND in SMS except PASSWORD which is not necessary USER LIST List of all users and their phone numbers which are used for ACTIONS User names are used only for better clarity SP10 d
7. Explanation Control outputs and monitor SP10 states is also possible from the configuration sw SeaConfigurator on a folder Monitoring 7 Configuration For local and remote configuration of SP10 and local and remote monitoring is used special program called SeaConfigurator The USB cable can be used for local configuration monitoring GPRS data connection can be used for remote configuration monitoring Actual version of SeaConfigurator can be downloaded free of charge on the website www seapraha cz fill in the word CONFIGURATOR into an entry field of the Search tool Example Configuration program SeaConfigurator basic screen C fi Label Name Device type Serial number Configurator 3 GSM SP10 GSM SP10 GB700001 ii Station Manager SEE Monitoring w Connect GPRS Configuration i Settings overview Phone Password On call Digital outputs Monitoring and Control State H Pulse Reset Name State L Regulation val vyp zap puls reset tepl fT More g More More gp More J More iy More lia Y2 vyp zap puls reset tepl ict vyp zap puls reset tepl Y4 vyp zap puls reset tepl ws vyp zap puls reset tepl Y6 vyp zap puls reset tepl Digital Inputs Temperature inputs Heated SMS Message Cooled SMS Message PWR f PWR 11 0 13 9 V Al Sf Al Alarm Circuits D Name Below Above 5 00 m 20 00 m SEA spol sr o 1 2
8. s possible to write more commands into one command SMS For higher readability separate commands by semicolon inside command use 1234 OUTPUTO ON OUTPUT1 ON OUTPUT3 PULSE Names of inputs and outputs are user definable by SeaConfigurator Command SMS may look like this 1234 GATE OPEN HEATING ON LAMP BLINK 6 2 Status SMS Text Message Whenever command SMS contains valid password SP10 always sends back status SMS Status SMS contains following information lt Device Name gt lt LogInput1 gt lt LogInput1Status gt lt LogInput2 gt lt LogInput2Status gt lt LogOutput1 gt lt LogOutput1Status gt lt LogOutput2 gt lt LogOutput1Status gt lt GSM Signal Level gt Status SMS message contains only information concerning selected inputs and outputs Selection is done using configuration program SeaConfigurator by checking the appropriate checkbox Explanation DEVICE SP10 Device Name user configurable Dinti 0on Digital Input 1 is on Digital Input 2 is off DOout3 on Digital Output 3 is on closed SIGNAL 58 GSM Signal level in 6 3 Control using SeaControl from Smart phone with Android This application can be used in smartphones with OS Android It makes it easy to control and monitor SP10 states This application can be installed free of charge from Google Play after insertion of word seacontrol 6 4 Control using SeaConfigurator PC with WIN 7 1 Important Terms
9. software was created by the best software engineers in SEA and was carefully tested both in SEA and also by SEA customers using GSM applications products made in SEA In spite of making all possible to get error free software it can happen that the software in CPU or PC programming SW or their mutual interaction has some error under some specific conditions If such error is found and the description of the problem including configuration file is sent by E mail to SEA Itd the error is removed free of charge and SEA will send new SW by E mail to customer SEA Itd has NO RESPONSIBILITY for any damage lost costs and any other problems direct or inducted caused by aaa such SW error by eventual device malfunction from any reason or by undelivered SMS from the device CE Declaration of conformity in accordance with the Radio and Telecommunications Terminal Equipment Directive 1999 5 EC R amp TTE and Directive 2011 65 EU ROHS We SEA spol s r o Dolnom cholupska 21 CZ 102 00 Praha 10 Czech Republic ID 47117931 manufacturer declare under our sole responsibility that product device for remote control and monitoring type GSM SP10 is in conformity with the following standards health and safety EN 60 950 1 2005 A1 2009 EN 60 950 1 2006 A11 2009 A1 2010 A12 2011 EMC ETSI EN 301 489 1 ETSI EN 301 489 7 v1 3 1 radio frequency EN 301 511 v 9 0 2 The last two digits of year in which the CE marking was affixed 13 SEA s r
10. SP10 User s Manual 1 Introduction GSM SP10 SP10 for short is a device for remote control and monitoring via GSM network SP10 has 8 digital outputs which can be changed or can generate pulse depending on SMS command or a voice call 9 digital inputs SP10 can react on these inputs by sending a SMS and or by a voice call and one analog input terminals Al A1 which can be configured as current input 0 to 20mA voltage input 0 to 10V or temperature input for various temperature sensors SP10 is equipped with an internal backup battery so it can operate even during power supply failure When long time operation on the battery is needed Power saving mode can be activated in configuration in which SP10 disconnects itself during several minutes from GSM network to minimize the power consumption Detailed data of SP10 activities can be logged into file in a MicroSD card Functions and names of inputs and outputs phone numbers password etc are fully user configurable using a personal computer via the USB cable or remotely via GPRS data using program SeaConfigurator which can downloaded free of charge on a webpage www seapraha cz fill in the word CONFIGURATOR into an entry field of the Search tool SP10 has an integrated DIN rail mount so you can comfortably place it into a cabinet 1 SIM card holder located under the removable cover 2 MicroSD card holder located under the removable cover 3 USB connecto
11. ble cover close to the SIM card reader A user can use SeaConfigurator to setup which data will be written into the log file e g input and output statuses changes analog values incoming and outgoing SMS messages Log file format is standard csv file Comma Separated Values The file name depends on the actual date datum csv In case there are more files created during one date the filenames are distinguished by sign followed by characters A to ZZ e g 130205 csv 130205 A csv 130205 B csv 130205 ZD csv etc This usually happens after SP10 reset or configuration changes manipulation with MicroSD card or SIM card Logged file can be erased only manually on PC There are two types of logged records periodical and event I O changes Event record contains actual analog values Periodical log file can contain average minimum maximum analog value Typical logged values LocalTime type phone text Y1 Y1 cmd Y2 Y2 cmd Y3 Y3 cmd Y4 Y4 cmd Y5 Y5 cmd Y6 Y6 cmd Y7 Y7 cmd Y8 Y8 cmd X1 X2 X3 X4 X5 X6 X7 X8 X9 PWW AP A1 ALM1 Batt Chg Batt Cap T int Ubat Inab GSM cell GSM signal GSM credit Example of one record of data 2014 05 04 14 15 43 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0 1 16 1 17 6 0 100 27 5 4209 1 23002F 2F20 049E_0030 38 Type of recorded data 1 regular by time 2 extra caused by change of digital input or output 3 incoming SMS 4 outgoing SMS 5 phone call outgoing 6
12. fore using the SIM card in SP10 Contact your mobile operator if necessary e Good quality GSM signal in area of installation of SP10 at least 2 bars on your mobile phone If there is a problem with GSM signal quality try to use another type of external antenna which can be placed in proper place with better GSM signal and which is connected to SP10 with several meters long coax cable with SMA connector Sufficient Credit in case of prepaid SIM card e Cancel all phone calls redirection and all automatic operators voice announcement for a SIM card in SP10 2 What is a phone number of SCA SCA Service Center Address of my mobile operator It s not possible to send an SMS Contact your mobile operator for this piece of information 3 I ve tested SP10 with my own SIM card Now I cannot find SMS messages formerly stored on my SIM card e SMS from your SIM card were processed by SP10 and then deleted They were very probably canceled due to syntactical error 4 Where can I find more and up to date information e Search GSM SP10 product on the website www seapraha cz English pages 11 Warranty General warranty period is 12 months after purchase when eventual malfunction device will be repaired free of charge in SEA company while shipping to SEA is paid by customer and SEA pays for shipping back to customer For SW there is 24 months warranty under following conditions Both CPU and PC software is sold as is The
13. ice SP10 insert an activated SIM card call the helpline of your GSM operator to the SIM card reader under the removable cover and connect the GSM antenna The SIM card is inserted into the reader by cut corner down and contacts to the center of SP10 Proper insertion can be identified by a mechanical click The SIM card can be removed by gently pressing until you hear a click and release Now the SIM card can be freely pulled out 2 Connect the power supply voltage from the DC voltage source 8 to 30 Vpc to the terminals and and power on the power supply 3 If the power supply is OK the green LED PWR lights At the same time after ca 20 seconds the blue LED GSM will briefly flash in the interval 1 time per 3 sec 4 Send the SMS text message from a mobile phone in form 1234 3 STATE to the phone number of the SP10 The device responds with a status message in the form Test SP10 Window Closed elevator Heating system OK ON SIGNAL 53 To use other functions it s necessary to configure the device using the program SeaConfigurator see below 5 Install the program SeaConfigurator The current software version can be downloaded free of charge on the web site www seapraha cz fill in the word CONFIGURATOR into an entry field of the Search tool Please follow the instruction during installation USB driver is installed automatically with SeaConfigurator GSM SP10 User s Manual EN v1 07 2014 05 07
14. m SeaConfigurator configured Otherwise the inputs can be damaged E g when an input is configured as temperature it must not be used to measure voltage or current Use only passive resistive temperature sensor when input configuration is for temperature measuring Warning Do not connect wires to analog inputs before analog inputs are properly 5 3 Digital outputs Y Digital outputs are labeled Y1 to Y8 The terminal C1 C4 is common for outputs Y1 to Y4 and the terminal C5 C8 is common for Y5 to Y8 The figure shows an example of the external and internal wiring circuits of output Y1 the same for all digital outputs Y2 output switches negative branch power relay coil and vice versa Re2 Y6 output switching power supply positive branch of the relay coil Re6 relay voltage must correspond to an external source voltage The polarity of the terminals C1 C4 and C5 C8 terminals is irrelevant can be plus or minus SP10 Outputs g 30V v1 v3 os ca ve oc coe R vstupy Internal wiring H of output Y1 i HO v1 Lo C1 C4 0 2A O Power supply of o SP10 8 to 30 V DC External power supply 8 to 30 V DC 5 4 Front Panel The front panel of the SP10 includes status LEDs of inputs outputs and status of of SP10 The states are only shown for inputs X1 to X8 and all outputs Y1 to Y8 LED for Y7 and Y8 are located above the USB connector In case an input or output is switched on its LED number lights o
15. o 2 Spole nost pro elektronick aplikace Dolnom cholupska 21 9 aa CZ 102 00 PRAHA 10 Hostival agrade tel 2 727 8 z 01 A CO 4711 1 Place of issue Praha Date of issue 2 9 2013 Ing Vladim r Ros lek director page 4 of 4
16. oes not use them in any way DEVICE OFF Disconnection of SP10 from any form of power supply including internal battery DEVICE ON Connection of SP10 to any form of power supply Processor reset has the same effect POWER ON OFF Connection disconnection of supply terminals from external power supply SP10 supplied from internal battery can send SMS about Power recovery and Power outage 8 SP10 in box SP10 can be placed into a special box order code GSM SP BOX MV equipped with power supply 230Vac 12Vpc type GSM PWR1 Empty space on the left side of GSM SP10 is intended for the expansion digital and analog inputs module GSM SP EXP On the BOX is mounted the panel SMA connector for antenna connection GSM ant na OWWWWWY ison ees Tarte Ta COM EEE DEAE REN SMS PROCESSOR GSM SP10 GSM PWR1 GSM SP BOX MV Box parameters Ingress Protection IP55 Outer box dimensions Width 166 mm Height 140 mm without connectors Depth 150 mm Next to power supply and SP10 can be placed GSM SP EXP or 8 pcs of relay in a socket e g GSM RELE OUT or GSM RELE OUT1 page 3 of 4 9 Troubleshooting Problems during installation of SP10 SP10 is not available on GSM network Problems during operation of SP10 Problem with remote configuration via GPRS No power supply Bad or not activated SIM card Low credit on prepaid SIM card Phone calls are redirected Low level of GSM signal
17. r under the square cover 4 8 outputs Y 2 x 4 5 DIN rail holder 6 Power supply 8 to 30 Vpc 7 LED for outputs status indication 8 LED for SP10 status indication 9 LED for inputs status indication 10 Analog input 0 to 10V 0 to 20 mA temper 11 GSM antenna connector 12 9 Digital inputs X 2 Package 1 pc GSM SP10 1 pc GSM antenna order code GSM ANTO5S 1 pc USB cable A B order code HW 11 02 8818 1 pc MicroSD card 2 GB 1 pc printed documentation this manual Accessories has to be ordered separately Box with power supply 230V GSM SP BOX MV Temperature sensor GSM C T2 range 20 C to 50 C based on sensor KTY81 210 Expansion Input Module GSM SP EXP 9 digital 7 analog inputs Communication module RS232 GSM SP CB2 or RS485 GSM SP CB5 3 Installation Before inserting the SIM card into the SP10 it is highly recommended to turn off setting of the PIN code Insert the active SIM card at least one call was made to any mobile telephone and turn off the requirement of setting the PIN On most mobile Warning Do not connect wires to analog inputs before analog inputs are properly configured telephones this option can be found in menu Setting the telephone protection or Setup gt Security gt PIN control Note The PIN is possible to activate later when the user became familiar with the configuration procedure of SP10 1 Before power on the dev
18. r blinks Under the removable cover is placed the SIM card reader the MicroSD card reader the button for turning the device into sleeping mode and a connector for connecting of an expansion board GSM SP CB2 or GSM SP CB5 or an expansion module GSM SP EXP The SIM card is inserted into the reader cut corner down and contacts to center of SP10 Proper insertion can be identified by a mechanical click SIM card can be removed by pressing gently on it until a click and release Then the SIM card can be pulled out Operation with the MicroSD card is similar An expansion connector is intended for connection of a communication board or using a flat cable expansion unit which can be located on left side of the SP10 on a DIN rail The USB connector for connection to the PC is hidden under the square cover GSM SP10 User s Manual EN v1 07 2014 05 07 LED Light Blink 1x per COLOR Dark 3sec Power ON or battery Power OFF powered signal GSM error operation Error Error operation green SIM card problem red Error during transition time before input status is accepted after input change before SMS can be sent input not activated input is activated 1to8 OUT output not output is activated activated 5 5 MicroSD card SP10 can store detailed information of its activities into a log file on a MicroSD card for later analysis The MicroSD card reader is located under the remova
Download Pdf Manuals
Related Search