Dehumidifier User Manual
Contents
1. 220 240V N 50Hz sL ld Note The Dehumidifier must have a good grounding 3 Selection of protective device and cable specification circuit Rated residual 30 30 breaker Operating current mA Power cable mm 3x4 Signal ine m Note The data above is suitable for power lines shorter than 10 meters For those longer than 10 meters the wire diameters must be increased The maximum length of signal line is 50 meters 4 Installation instructions and requirements Dehumidifier must be installed by professional technicians and you as users cannot do the installation by yourselves in case that it may cause harm to others and yourself or damage the machine A Installation of machine 1 2 3 Dehumidifier should be installed in a place with good ventilation The bolt M 12 must be used to fix the machine body during the installation The machine can be fixed on the concrete foundation or support with the concrete foundation being firm and the support being of great strength and anti rust treatment Please notice that there will be condensate water coming out from classis during the operation Conne2. wired controller display ae Overheat Protection only available with EC heating element Appendix 1 Installation of Heating Element Optional Warning The heating element of dehumidifier must be installed and trial by qualified electrician A Heating element s break down 1 Heating Element 1pc 2 Screws 4pcs B Steps 1 Turn off the machine and shut off the power Use a Phillips screwdriver to takeoff the 8pcs screws from the side panels Dismantle the front panel 2 Take off the 2pcs screws on the left side of electric element take off the bottom strip 3 Put the heating element on the top of the dehumidifier make sure the four holes of heating element in the right position against the four holes of top panel 6 Open the cover of electric box and drill the signal cable amp power cord through the holes and pull it to the electric box 8 Connect the power cord of heating element as bellowed chart Heating Element Electric Heating Power supply L Electric heating overheat protection POWER 220 240V 50Hz 9 Install the electric box cover and dehumidifier s front panel back 10 After adding the heating element please refer to Appendix 2 Advanced application of inner parameter and reset the code Cl s value to 1 the default value of Cl is 0 Appendix 2 Advanced application of inner parameter Warning Non professional is not recommended to avoid er
3. Dehumidifier User Manual For the series of DP40 DP70 Content I Please re d immediately seitin onn aa eiai da adea MTs APPC ON cicastas sei E tease A A eames eaten eects 2 Ie Fei unione E T A 2 Eye Techne Paramet Se oss daca asia cosseedacenaoascosseecucme asses 3 V Overall Dimensioon r e E E EE 4 Vi nstallat Gud anna nE E A dears 5 Vit LCD Controller Operation sonrssroikia r a a a 8 VIN Test ronmin a rien eernialeen ele ane nee 10 A bes 610728 18 E eo Te SPP EET SPP CT Tn SP Cn OP eC 11 Me Reparan a MENAN Ee a a E N E eae 12 XI General Troubl eshootnh E serren E EE 13 AM Faaltdis play screen EEA ERR 13 Appendix 1 Installation of Heating Element Optional eens 14 Appendix 2 Advanced application of inner parametef sseeeseeeeseeeeees 17 Please read immediately Attention This machine is an ordinary Dehumidifier and can never be used for regulating other combustible gas and stale air The main power switch should be installed out of the reach of children to avoid dangers caused by their playing with the switch If it 1s necessary to remove the machine shell during repair and maintenance please make sure that power has been cut off Notice for Use The repair and maintenance must be conducted by qualified and professional mechanics The power supply circuit must be in line with the local standards and please read instructions carefully Set appropriate humidity levels to create a co
4. X Precautions 1 The usage should notice that Ay By C D Es Fy G H Please don t place any object close to the air inlet or outlet which may block the airflows Otherwise the efficiency may be reduced or the whole operation of the system may even stop Don t put hands sticks or other objects into the air outlet of Dehumidifier And don t dismantle the fan cover otherwise the fan running at a high speed may cause harm to you If any abnormal situation appears such as strange noises smell smoke electric leakage etc electricity should be cut off immediately and the local dealers should be contacted Don t repair the machine by yourself The usage or storage of hair gel paint oil or other combustible gas or liquid near the device is forbidden otherwise there might be fires Drip washing the machine directly with water is forbidden Please don t stand on or lean against the machine Please don t use it to preserve the artworks or academic materials or for other special purposes otherwise the quality of restored objects might be reduced This machine is only for indoor use Please don t use it under the conditions with direct sunlight or wind and rain 2 Safety rules As The main power switch should be installed out of the reach of children to avoid dangers caused by their playing with the switch ey ee B If the electricity fails during the usage this Dehumidifier will start
5. automatically after the power restoration Therefore please switch off this machine Otherwise there might be some accidents C Please cut off the main power in thunderstorm weather or else the lightning may damage the machine D Please cut off the main power and drain water out of the machine if it is not used for a long time X Repair and maintenance 1 Before examining and repairing the Dehumidifier its power must be cut off 2 In seasons when this device is not used please cut off its power and cover the machine body with plastic cloth so as to avoid the dust 3 When the machine is washed the domestic neutral detergent or clear water is recommended and the volatile oil gasoline diluent agent or polishing power for washing 1s forbidden 4 Regularly checking if the bolts has become loose if the wires have been worn or if the connections are firm ee XI General Troubleshooting Cause Handling method Waiting for power restoration Switch on the power Not operating Check the problem and Fuse burnt out replace the fuse Check the problem and Leakage circuit breaker oo switch on the leakage circuit being off breaker If the problems above cannot be solved please contact professional workers and inform them of the product type and details about faults Attention Never dismantle the machine and repair it by yourself so as to avoid any danger XII Fault display Error Code Protection fault
6. ct the drain port to the drainage hole in classis and link the drainpipe to enable the smooth flowing out of condensate water Electrical wiring installation 1 2 3 4 5 Use the special power supply and the supply voltage should be in line with the rated voltage of this product The Dehumidifier must have a good grounding Wiring must be conducted by professional technicians in accordance with the standards of circuit diagram According to related technical standards for electrical equipment specified by the nation users are located in the electric leakage protection device must be well set the residual operating current should be less than 30 mA Power line and signal line arrangement should be tidy and reasonable without any interference Given the environmental conditions environmental temperature direct sunlight rainwater grid voltage cable length etc the sectional area can be increased C When the wiring construction is finished the power can be on if there are no faults after careful checking VII LCD Controller Operation Heatin RT g Ventilation only available with extra heating element Dehumidification Ambient temperature timer time Relative humidity Fan Speed Timer on off Power on off key Timer on off key Mode key Wind Speed key 1 Display a The screen will display actual relative humidity and ambient temperature C when the machine is of
7. defrosting High quality compressor of world famous brands Convenient installation and easy operation IV a Parameters ModeRef Ref DP40 DP70 Capacity in l h Air 30 C Humid 70 Heat Recovered KW a Electric Heating Optional kw Rated Power kW een en Power supply 220 240 V 1Ph SOHz Net Weight Gross Weight 53 68 70 86 Kgs 1 The rated current with electric heating will be 8 7A for DP40 13A for DP70 1 Dehumidifying capacity refers to the dehumidifying volume when keeping the relative humidity at 30 C 70 2 Devices of this series can operate normally at the temperature of 5 C 38 C Effects cannot be guaranteed if not within this range Please notice under different working conditions the technical parameters of the Dehumidifiers may vary 3 Due to the technical advances related parameters will have phase adjustments without additional notices Please refer to the nameplate for more information V Overall Dimension ni ae a i a LOOO i aS fe fete fe fe o es as a me ee eee ieee Note Above is the dimension specification figure and is only for the reference of professional workers during installation and arrangement Due to the continuous improvements the products
8. f b The screen will display following message when the machine is on 1 Mode 2 Actual relative humidity and ambient temperature C 3 Fan speed and timer if set 2 Setting a Mode setting When the machine is on press M key to switch the mode Dehumidifying mode 2 Ventilation mode 4 wl Heating mode aS only available with extra heating element Dehumidifying and Heating b Set Humidity setting range 30 99 In the dehumidifying mode no matter machine s on or off every time you press button A or V the set humidity will be increased or decreased by 1 It ll flash for 8 seconds and then display the actual humidity again To check the set humidity press A or V key under dehumidifying mode c Set Fan Speed oar na nem When the machine s on and in ventilation mode press SET to switch the speed from High speed aMi and low speed al d Timer Setting 1 Set timer When the device is on the off time can only be set as 1 12H When the machine is off the on time can only be set as 1 12H Press button Start the timer setting and change the timer time through button A and Y 2 Cancel the timer Press to have the time value flashing then press button Io cancel the timing and press lt Q to exit e Keypad lock setting Press A and W simultaneously for three seconds so as to open close the ke
9. mfortable environment Dust gauze must be cleaned regularly Please don t place objects close to the air inlet or outlet which may block the airflows If the electricity fails during the usage this device will start automatically after the power restoration Don t put hands sticks or other objects into the air inlet and outlet Don t dismantle the running fans of the dust gauze If any abnormal situation appears such as strange noises smell smoke electric leakage etc electricity should be cut off immediately and the local dealers should be contacted Don t repair the machine by yourself The usage or storage of hair gel paint oil or other combustible gas or liquid near the device is forbidden otherwise there might be fires II III E ae ee R a Se Application Economically and efficiently dehumidify providing you with cozy environment Users can decide the machine type by referring to the technical parameters and under the guidance of professional personnel Dehumidifiers of this series have been adjusted to the best of its ability and they can work normally after the wiring and connection of the drainage tube by professional workers under the standards Features Efficient heat exchanger Sensitive and accurate computer controlling of humidity Environmental cooling medium R410A High voltage low voltage and overheat protection system Ultra low temperature automatic stop system Computer automatic
10. ror by incorrect operation Inner parameter s checking amp setting 17 Press button SET for three seconds and enter the menu of parameter checking amp setting Parameters Code The smaller 8 displays codes and the bigger 8 displays the relative parameters A To check the inner parameters When machine s on press button Set for 3 seconds And then press button A and V to check the code and relative parameter B To set the inner parameters When machine s off press button Set for 3 seconds Press A and V to check each code amp parameter press Set and the code will flash you can press A and Y to reset the parameter value After press Set to confirm And press T ar O to exit The parameter table is as follows Parameter Se Parameter specification Default value meaning 0 no I yes a Measured value C2 Coil temperature 20 C 99 C 5 5 18 compensation Defrosting cycle 20Min 90Min Defrosting starting 10 C 10 C temperature 6 Defrosting closing 0C 15 C temperature Maximum defrosting 2Min 12Min time O reaching the set value Working state and the fan stops of draught 1 reaching the set value fan and the fan operates with low wind temperature value temperature value value degree Ox Version H64 20130719
11. will have phase adjustments without additional notices VI Installation Guide 1 Position 1 The distance of dehumidifier must be over 2 meters from the swimming pool Ambient Floor Standing Ambient_Wall Mounted l i TT 4 i TI ia Lt ami LP 1 i 4 ae rr a LL p al l l I l rer Cold Humid air _ late Ld Cold Humid air 2 Make two holes in a strong wall and knock two explosion screws ofp 12mm 3 Hang the machine from the screws firmly through two circular holes on the back of the machine 4 Connect the drainpipe 5 Connect the signal lines and power line in accordance with the connection ani AN Lo ae Z i l Qw A signal line B power line C water outlet Note The figure above is an example and the machine installation and arrangement ts only for reference 2 Electrical wiring diagram Breaker fuse Customer prepare Earthing P AN Power Cord Power Supply L
12. ypad lock f Set Heating only available with extra heating element the setting range is from 18 C to 32 C NA Under heating mode 7 pS every time you press A or V the set temperature can be increased or decreased by 1 C To check the set temperature press A or V and it ll display the set temperature g Set Humidity amp Heating only available with extra heating wiles Under mode dehumidifying and heating j 1S press A or V to reach the set humidity amp temperature Press to switch on humidity and temperature VIII Test running 1 Checking before usage A Check whether the whole machine is place on the ground vertically and be connected with drainpipes B Check whether the electrical wiring has been connected in accordance with the electrical wiring diagram and whether the earth wire has been linked reliably C Check whether the power of host machine has been cut off D Check whether the set humidity is appropriate E Ensure the air inlet and outlet of the Dehumidifier haven t been blocked 2 Test run 10 Ay Users should first switch on the power B To protect the dehumidifier the device has the start delay function Every time when the machine is switched on the draught fan starts first and then the compressors operate automatically one minute later C After the dehumidifier start check whether there is any strange noise along with the machine operation I
Download Pdf Manuals
Related Search