Cl5808 CL5816 User Manual
Contents
1. o JE o Sp 4 5 No Component Description 1 Power Socket This is a standard 3 prong AC power socket The power cord from an AC source plugs in here 2 Power Switch This standard rocker switch powers the unit on and off 3 External The external KVM console cables plug into the ports in this Console Section section The section consists of ports for USB or PS 2 keyboard and mouse and a VGA monitor 4 Grounding The grounding wire used to ground the switch attaches here Terminal 5 KVM Port The cable that links the CL3000 to the KVM switch plugs in Section here Note The shape of this SPHD connector has been specifically modified so that only KVM cables designed to work with this switch can plug in see Cables page 3 for details CL3000 User Manual This Page Intentionally Left Blank Chapter 2 Hardware Setup Before you Begin device is provided on page 27 Please review it before proceeding l 1 Important safety information regarding the placement of this 2 Make sure that power to all the devices you will be connecting up have been turned off You must unplug the power cords of any computers that have the Keyboard Power On function Standard Rack Mounting A standard rack mount kit is provided with your CL3000 The kit enables the console to be mounted in rack with a depth of 42 72 cm NU Side Mountng Brackets Note 1 I2. When a firmware upgrade procedure fails To perform a firmware upgrade recovery do the following 1 Power off the CL3000 2 Slide the Firmware Upgrade Recovery Switch to the Recover position 3 Power the CL3000 back on and repeat the upgrade procedure 4 After the switch has been successfully upgraded power it off and slide the Firmware Upgrade Recovery Switch back to the Normal position 5 Power the CL3000 back on Exiting Firmware Upgrade Mode To exit the Firmware Upgrade Mode do the following 1 Slide the Firmware Upgrade Recovery Switch see page 6 to the Normal position 2 Power off and restart the CL3000 according to the instructions given in the Powering Off and Restarting section see page 18 26 Appendix Safety Instructions General This product is for indoor use only Read all of these instructions Save them for future reference Follow all warnings and instructions marked on the device Do not place the device on any unstable surface cart stand table or other surfaces If the device falls serious damage will result Do not use the device near water Do not place the device near or over heat radiators or heat vents The device housing is provided with slots and openings to allow for adequate ventilation To ensure reliable operation and to protect against overheating these openings must never be blocked or covered The device should never be placed on a soft s
3. LED backlit LCD 4 x Pushbutton Adjustment LEDs Power 1 Green Lock Num 1 Green Caps 1 Green Scroll 1 Green Emulation Keyboard Mouse PS 2 USB Video 1280 x 1024 75Hz DDC2B UD Rating 100 240VAG 50 60Hz 1A Power Consumption 120V 21 4W 230V 22 7W Vibration Test MIL STD 810G Certified Environment Operating Temp 0 40 C Storage Temp 20 60 C Humidity 0 80 RH Non condensing Physical Housing Metal Properties Weight 9 00 kg Dimensions L x W x H 48 00 x 58 92 x 4 40 cm CL3000 User Manual Optional Rack Mounting For convenience and flexibility three optional rack mounting kits are available as shown in the following table Bracket Type Size cm Standard Installation Long 70 0 105 0 Easy Installation Short 57 0 70 0 Easy Installation Long 68 0 105 0 To install the long bracket standard rack mount kit simply replace the short L brackets on the standard rack mount kit with the long ones and mount the CL3000 according to the instructions given for Standard Rack Mounting page 9 While it takes two people to perform a standard installation with an Easy Installation kit one person can mount the CL3000 To install the Easy Installation kit do the following 1 Remove the standard sliding L brackets not shown and the side mounting brackets from both sides of the CL3000 Phillips head hex M4L4 6pcs 32 Ap
4. http www aten usa com CL3000 User Manual This Page Intentionally Left Blank Chapter 1 Introduction Overview The CL3000 is an integrated KVM keyboard monitor and mouse console module that serves as the front end console for compatible KVM switches Lightweight and with a 19 power saving LED backlit LCD the CL3000 offers a space saving streamlined approach to KVM switch technology by integrating a keyboard LED backlit LCD monitor and touchpad in a 1U housing Additional console ports allows the second user local access while in conjunction with an ATEN Over the Net KVM switch or IP access unit you can remotely control computers that are located anywhere around the world MIL STD 810G testing provides certified reliable operation of the CL3000 Console in harsh environments The MIL STD 810G uses advanced testing procedures to emphasize the equipment s environmental design and limits in real world conditions which it will experience throughout its life such as operating in moving vehicles or functioning on factory floors where vibrations are high and experienced frequently There is no better way to save time and money than with a CL3000 installation By using the CL3000 with its light weight and green power LED backlit LCD monitor to manage your installation you 1 eliminate the expense of having to purchase a separate keyboard monitor and mouse for each computer 2 save all the space those extra compone
5. Chapter 4 The Firmware Upgrade Utility INTRODUCTION se ese feces Es Er ee 21 Before You Begin aan aus ar Bee 21 Firmware Upgrade Mode 22 Starting the Upgrade 23 Upgrade Succeeded 25 Upgrade Failed oe er ee ee 25 Firmware Upgrade Recovery 26 Exiting Firmware Upgrade Mode 26 Appendix SatetyInstructions zz see ae gees hie Ad ais 27 Generala ae Sod R A Sep le pa nee ete Gs 27 Rack Mounting 222 5 ee be ah de ae an geen nee aa 29 Technical Supports i ea eaa er eal elle 30 Inte rnational 5 sar Z T R a b et ch SE eS 30 North America sa R eR latente te a near 30 Specifications 2 324 er ea baer 31 Optional Rack Mounting 32 Sun Keyboard Emulation 36 Troublesho ting 2 Sra cae gerade ees aca weed ila eae 37 About SPHD Connectors 37 Limited Warranty 20 0c eee eee een 37 vii CL3000 User Manual About this Manual This User Manual is provided to help you get the most from your CL3000 system It covers all aspects of installation configuration and operation An overview of the information found in the manual is provided below Chapter 1 Introduction introduces you to the CL3000 system Its purpose features and benefit
6. Emulation The PC compatible 101 104 key keyboard can emulate the functions of the Sun keyboard when the Control key Ctrl is used in conjunction with other keys The corresponding functions are shown in the table below PC Keyboard Sun Keyboard Ctrl T Stop Ctrl F2 Again Ctrl F3 Props Ctrl F4 Undo Ctrl F5 Front Ctrl F6 Copy Ctrl F7 Open Ctrl F8 Paste Ctrl F9 Find Ctrl F10 Cut Ctrl 1 wt Ctrl 2 Oo mQ Ctrl 3 Ctrl 4 C Ctrl H Help Es Compose sa Note When using key combinations press and release the first key Ctrl then press and release the activation key 36 Appendix Troubleshooting Symptom Action Some characters enter from The keyboard layout setting for the port does not the keyboard do not display match the keyboard you are using On your switch correctly change the keyboard layout setting for the port to match the layout of the keyboard you are using can t use the special keys on Use Sun keyboard emulation keystrokes page 36 to the Sun external keyboard to achieve all Sun keyboard functions control Sun computers About SPHD Connectors This product uses SPHD connectors for its KVM and or Console ports We have specifically modified the shape of these connectors so that only KVM cables that we have designed to work
7. ATEN Lightweight PS 2 USB LCD Console CL3000 User Manual www aten com CL3000 User Manual EMC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense The device complies with Part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment CE Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures KCC Stateme
8. Section of the KVM switch 3 Plug your external console keyboard monitor and mouse connectors into their respective ports in the Console Section of the CL3000 located on the unit s back panel 4 If you are using an external USB mouse or USB peripheral in your installation plug it into the USB port located on the CL3000 s front panel 5 Plug the power cord into the CL3000 s power socket and into an AC power source 6 Power up your KVM installation 7 Turn on the power to CL3000 CL3000 User Manual A QD o n a gt Chapter 3 Operation Opening the Console The CL3000 s console is located under the top cover To access the console slide the console module out and raise the cover Note As a safety precaution to keep the console from accidentally sliding out the console is locked into the Jn position Before you can pull the console module out you must release it by pushing the catches on the unit s front panel as indicated below CL3000 User Manual Closing the Console To slide the console module back in close the cover and do the following 1 Pull the safety catches on the unit s side rails toward you and push the module in u
9. eds status messages appear in the Status Messages panel and the progress toward completion is shown on the Progress bar 24 Chapter 4 The Firmware Upgrade Utility Upgrade Succeeded After the upgrade has completed a Screen appears to inform you that the procedure was successful 75 Firmware Upgrade Utility The Firmware upgrade was successful Click Finish to close the utility Device List Status Messages gt Loading amp testing files gt Loading amp testing files OK gt Searching for devices gt Preparing firmware upgrade gt Firmware version is not newer than device MAIN 001 001 gt Preparing firmware upgrade OK gt Upgrading device MAIN 001 001 gt Uparading device MAIN 001 001 OK gt Upgrading device KB 001 004 gt Upgrading device KB 001 004 OK Device Description Device F W Ver 3 0 292 Upgrade F W Ver 1 0 081 MID 001 004 Click Finish to close the firmware upgrade utility Upgrade Failed If the Upgrade Succeeded screen doesn t appear it means that the upgrade failed to complete successfully See the next section Firmware Upgrade Recovery for how to proceed 25 CL3000 User Manual Firmware Upgrade Recovery There are three conditions that call for firmware upgrade recovery When the unit s firmware becomes corrupted for some reason and you are unable to operate it When a firmware upgrade procedure is interrupted
10. fety Instructions General 27 Rack Mounting 29 SJ T 11364 2006 iii Specifications CL5708D CL5708E 31 Standard rack mounting 9 System Requirements Cables 3 External Console 3 T Technical Support 30 Telephone support iv U User Notice iv 39
11. fy the layout we strongly recommend that you use high quality custom cable sets available in varying lengths described in the table below which can be purchased from your dealer Length m Part Number 1 20 2L 5201P 1 80 2L 5202P 3 00 2L 5203P 6 00 2L 5206P 1 80 2L 5702P 1 20 2L 5201U 1 80 2L 5202U 3 00 2L 5203U 5 00 2L 5205U CL3000 User Manual Operating Systems Supported operating systems are shown in the table below OS Version Windows 2000 and higher Linux RedHat 9 and higher SuSE 10 and higher Debian 3 1 4 0 Ubuntu 7 04 7 10 UNIX IBM AIX 4 3 5L FreeBSD 4 2 and higher Sun Solaris 8 and higher Novell Netware 6 0 and higher Mac OS 9 and higher DOS 6 22 Chapter 1 Introduction Components Front View No Component Description 1 Upper Handle Pull to slide the LED backlit LCD module out push to slide it in See Opening the Console page 19 for details on sliding the console in and out 2 Module Release In order to slide the console out you must first release it by Catches sliding these catches to the inside 3 LED backlit LCD See Rear View page 7 Module CL3000 User Manual No Component Description 4 LED backlit LCD The buttons to control the position and picture settings of the Controls LED display are located here See page 16 for de
12. ghtly from these examples 2 Read and Agree to the License Agreement enable the I Agree radio button 3 Click Next to continue 23 CL3000 User Manual The Firmware Upgrade Utility main screen appears The devices capable of being upgraded are listed in the Device List panel 2 Firmware Upgrade Utility Check Firmware Version is checked the utility compares the device s fimware level with the upgrade files If the devices version is newer the utility lets you decide whether to continue or not If it is not checked the utility performs the upgrade directly Click Next to begin Device List Status Messages gt Loading amp testing files gt Loading amp testing files OK gt Searching for devices IV Check Firmware Version Progress Help View Log Click Next to perform the upgrade If you enabled Check Firmware Version the utility compares the device s firmware level with that of the upgrade files If it finds that the device s version is higher than the upgrade version it brings up a dialog box informing you of the situation and gives you the option to continue or cancel Warning 9 The firmware Ver 1 0 092 is not newer than current firmware Ver 1 0 092 v7 in device MAIN 001 001 Continue the upgrade Yes No If you didn t enable Check Firmware Version the utility installs the upgrade files without checking whether they are a higher level or not As the upgrade proce
13. ine technical support including troubleshooting documentation and software updates http support aten com For telephone support Telephone Support page iv North America Email Support support aten usa com Online Technical Support Troubleshooting Documentation Software Updates http www aten usa com support Telephone Support 1 888 999 ATEN ext 4988 When you contact us please have the following information ready beforehand Product model number serial number and date of purchase Your computer configuration including operating system revision level expansion cards and software Any error messages displayed at the time the error occurred The sequence of operations that led up to the error Any other information you feel may be of help 30 Appendix Specifications Function CL3000 Computer Connections 1 Console Selection Hotkey 1 x 6 pin Mini DIN Female Purple 1 x USB Type A Female Black 1 x HDB 15 Female Blue Connectors External Keyboard Console Ports Video Mouse 1 x 6 pin Mini DIN Female Green 1 x USB Type A Female Black KVM Ports 1 x SPHD 18 Male Yellow USB Port 1 x USB Type A Female Black Power 1 x 3 prong AC Socket Switches Reset 1 x Semi recessed Pushbutton Power 1 x Rocker F W Upgrade 1 x Slide LED backlit LCD Power 1 x Pushbutton
14. ionality is immediate upon switching to USB mouse mode Ctrl Alt Shift U P Enter Configures the front USB Port to peripheral mode Note 1 Press the keys in sequence one key at a time First Ctrl then Alt then Shift etc 2 Console selections are not saved If the CL3000 is powered off it reverts to the default setting of both consoles enabled when it is powered on again 3 If the KVM switch connected to the CL3000 uses the Ctrl Alt Shift combination to invoke its hotkey mode you won t be able to access any of its hotkey operations because the CL3000 will capture the combination for console selection first 19 CL3000 User Manual This Page Intentionally Left Blank 20 Chapter 4 The Firmware Upgrade Utility Introduction The purpose of the Windows based firmware upgrade utility is to provide an automated process for upgrading the CL3000 firmware As new firmware versions become available new firmware upgrade packages are posted on our website Check the website regularly to find the latest information and packages Before You Begin To download the firmware upgrade package 1 From a computer that is not part of your KVM installation go to our website and choose the model name that relates to your device Choose the firmware upgrade package that you wish to install usually the most recent and download it to your computer 2 Connect the KVM cable
15. ndard Rack Mounting Kit Long Easy Installation Rack Mounting Kit Short Easy Installation Rack Mounting Kit Long Check to make sure that all the components are present and that nothing got damaged in shipping If you encounter a problem contact your dealer Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit and or any of the devices connected to it Features may have been added to the CL3000 since this manual was published Please visit our website to download the most up to date version of the manual Copyright 2015 ATEN International Co Ltd Manual Date 2015 08 19 ATEN and the ATEN logo are registered trademarks of ATEN International Co Ltd All rights reserved All other brand names and trademarks are the registered property of their respective owners CL3000 User Manual Contents EMC Information sa ee er er Laie abe ii ROHS i244 dan en eee els TR hs ii SULT 11304 2000 Gnade iii User Information sanai a a a N A E E iv Online Registration iv Telephone Support iv User N tiGe seins N RA ea ate ead Re led ned ne uns iv Package Contents V Basic Package uses coche re ns V Optional Equipment V About this Manual viii CONVENTIONS aii anne ols a eye o
16. nt FA AES Aw 717 AT BS SA 7171 ol 77S AFS AF AAS 7 7 SA BHA EE AS FL SHA 7 2 7F4 JA Z AoA ARS SHE 7 ut rd RoHS This product is RoHS compliant CL3000 User Manual SJ T 11364 2006 The following contains information that relates to China O SJIT 11363 2006 O SJ T 11363 2006 X SJ T 11363 2006 CL3000 User Manual User Information Online Registration Be sure to register your product at our online support center International http eservice aten com Telephone Support For telephone support call this number International 886 2 8692 6959 China 86 10 5255 0110 Japan 81 3 5615 5811 Korea 82 2 467 6789 North America 1 888 999 ATEN ext 4988 United Kingdom 44 8 4481 58923 User Notice All information documentation and specifications contained in this manual are subject to change with
17. ntil it stops 2 Release the catches Pull the module slightly toward you then push it all the way in Note The reason for the two step procedure is to minimize the chances of you pinching your fingers when sliding the module in Chapter 3 Operation Operating Precautions The maximum load bearing capacity of the keyboard module is 30 kg Failure to heed the information below can result in damage to the keyboard module Right Rest your hands and arms lightly on the keyboard module as you work Wrong DO NOT lean your body weight on the keyboard module DO NOT place heavy objects on the keyboard module 15 CL3000 User Manual LED backlit LCD OSD Configuration LED backlit LCD Buttons The OSD allows you to set up and configure the LED backlit LCD display Four buttons are used to perform the configuration as described in the table below Button Function MENU 4 When you have not entered the LED backlit LCD OSD Menu function pressing this button invokes the Menu function and brings up the Main Menu When you have entered the LED backlit LCD OSD Menu function and have reached a setting choice with the navigation buttons pressing this button brings up its adjustment screen KA When navigating through the menus this button moves you Right or Up When making an adjustment it increases the value lt iv When naviga
18. nts would take up 3 save on energy costs and 4 eliminate the inconvenience and wasted effort involved in constantly moving from one computer to another The Benefits of LED backlit LCDs LED backlit LCDs are a new generation of display technology that uses LED backlighting instead of the cold cathode fluorescent lamps CCFLs used in traditional LCDs This provides great benefits that include lower power consumption a more dynamic range of colors and better heat dissipation as well as increased display brightness and higher contrast levels When you factor in the LED backlit LCDs longer life and greater stability it is no wonder that they are fast becoming the display of choice in many different environments from commercial advertising and sports venues to advanced computer displays and high end televisions CL3000 User Manual Features Exclusive LED illumination light designed by ATEN to illuminate the keyboard and touchpad to allow visibility in low light conditions Integrated KVM console featuring a 19 LED backlit LCD monitor in a Single Rail Slideaway housing Green power LED backlit LCD monitor saves energy Lightweight design for easier installation MIL STD 810G Standard Certified Testing Dual Interface supports computers with PS 2 or USB keyboards and mice Additional hot pluggable USB mouse port on front panel also functions as USB peripheral port Multiplatform support Wind
19. ome screen appears 2 Firmware Upgrade Utility Welcome to the Firmware Upgrade Utility Put your device into Firmware Upgrade Mode Use the Firmware Upgrade Cable to connect its Firmware Upgrade Port to your computer or connect via Ethemet Agree to the License Agreement Then Click Next LICENSE AGREEMENT LICENSE GRANT goces Intemational Co Ltd Licensor grants to you a non exclusive nontransferable license to ss and use FIRMWARE UPGRADE UTILITY tthe Product during the Term set forth below ou may install the Product on a hard disk or other storage device install and use the Product on a file server for use on a network for the purposes of permanent installation onto hard disks or other storage devices or i use of the Product over such network and make backup copies of the Product RESTRICTIONS You agree not to modify adapt translate reverse engineer recompile disassemble or otherwise attempt to discover the source code of the Product or create derivative works based on the Product or remove any proprietary notices or labels on the Product including copyright trademark or patent pending notices You may not sublicense the Product or otherwise allow others to use the Product licensed to you v Agree C 1Dont Agree Help About Note The screens shown in this section are for reference only The wording and layout of the actual screens put up by the Firmware Upgrade Utility may vary sli
20. out prior notification by the manufacturer The manufacturer makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose Any of the manufacturer s software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not the manufacturer its distributor or its dealer assumes the entire cost ofall necessary servicing repair and any incidental or consequential damages resulting from any defect in the software The manufacturer of this system is not responsible for any radio and or TV interference caused by unauthorized modifications to this device It is the responsibility of the user to correct such interference The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE CL3000 User Manual Package Contents Basic Package The basic CL3000 package consists of 1 CL3000 Lightweight PS 2 USB LCD Console with Standard Rack Mounting Kit 1 Custom KVM Cable 1 Power Cord 1 User Instructions Optional Equipment Depending on any optional equipment that you may have purchased one of the following may be included in your package Sta
21. oves the display area left or right V Position Positions the display area on the LED backlit LCD panel vertically moves the display area up or down Color Temperature Adjusts the color quality of the display You can adjust the warmth value color balance etc The Adjust Color selection has a further submenu that lets you fine tune the RGB values Language Selects the language that the OSD displays its menus in OSD Duration Lets you set the amount of time the OSD displays on the screen lf there is no input for the amount of time you choose the OSD display turns off Reset Resets the adjustments on all menus and submenus to their factory default settings Note The Language setting does not return to the factory default but remains at the one that you have set it to Manufacturing Number The MFG Number Manufacturing Number is an internal serial number used by ATEN s factory and technical support staff to identify products This number does not affect products warranty If your product requires after sales services you may provide the MFG Number to ATEN s sales or technical support staff to identify the product and model number 17 CL3000 User Manual Hot Plugging The CL3000 supports hot plugging components can be removed and added to the console by unplugging their cables from the ports without the need to shut down the CL3000 Powering Off and Restarting Ifit become
22. ows Linux Mac and Sun Supports high resolution video up to 1280 x 1024 75 Hz DDC2B Firmware upgradable Extra console port manage computers from an external console monitor USB or PS 2 keyboard and mouse Console lock the console remains securely locked away when not in use Slideaway housing is slightly less than 1U with top and bottom clearance for smooth operation in 1U of rack space DDC emulation video settings of each computer are automatically adjusted for optimal output to the monitor Adjustable depth to fit within a rack Standard 105 key keyboard Keyboard languages supported English US English UK French German German Swiss Greek Hungarian Italian Japanese Korean Russian Spanish Swedish and Traditional Chinese Chapter 1 Introduction Requirements LED backlit LCD Console The LED backlit LCD console supports most KVM switches If you are unsure whether your switch is supported or not check with your dealer The integrated LED backlit LCD monitor s maximum resolution is 1280 x 1024 75Hz Make sure that none of the resolution settings of the connected computers exceed the LED backlit LCD monitor s maximum resolution External Console A VGA SVGA or MultiSync monitor capable of displaying the highest resolution provided by any computer in the installation USB or PS 2 keyboard and mouse Cables For optimum signal integrity and to simpli
23. pendix 2 Attach the left and right easy installation mounting rails to the inside of the rack The flange that supports the CL3000 will be to the inside Rear Flange Slide Bar N Front Flange Rear Attachment Sliding Bracket a Screw the front flanges to the rack first b Slide the bars with the rear flanges toward the rack until the flanges make contact with the rack then screw the rear flanges to the rack 33 CL3000 User Manual 3 Slide the CL3000 onto the support flanges Use the screws supplied with this package to loosely attach the front of the CL3000 to the front of the rack only tighten the screws part way Phillips head M4L6 4 Slide the rear attachment sliding brackets along the slide bars until they contact the rear of the CL3000 then use the screws supplied with this package to attach the bars to the rear of the CL3000 tighten the screws all the way Phillips head M4L6 SEF SSS 34 Appendix 5 Slide the CL3000 open and closed a couple of times to be sure that it is properly aligned and operating smoothly See Opening the Console page 13 for opening and closing procedures 6 After determining that the CL3000 is lined up and operating correctly finish by fully tightening the front attachment screws inserted in Step 3 35 CL3000 User Manual Sun Keyboard
24. s are presented and its front and back panel components are described Chapter 2 Hardware Setup describes how to set up your installation Chapter 3 Basic Operation explains the fundamental concepts involved in operating the CL3000 Chapter 4 The Firmware Upgrade Utility explains how to use this utility to upgrade the CL3000 s firmware with the latest available versions An Appendix provides specifications and other technical information regarding the CL3000 viii CL3000 User Manual Conventions This manual uses the following conventions Monospaced A Indicates text that you should key in Indicates keys you should press For example Enter means to press the Enter key If keys need to be chorded they appear together in the same bracket with a plus sign between them Ctrl Alt Numbered lists represent procedures with sequential steps Bullet lists provide information but do not involve sequential steps Indicates selecting the option on a menu or dialog box for example that comes next For example Start Run means to open the Start menu and then select Run Indicates critical information Product Information For information about all ATEN products and how they can help you connect without limits visit ATEN on the Web or contact an ATEN Authorized Reseller Visit ATEN on the Web for a list of locations and telephone numbers International http www aten com North America
25. s necessary to Power Off the CL3000 to upgrade the firmware for example simply turn off the power to the unit using the rear panel power switch To restart the CL3000 turn the rear panel power switch back on Port ID Numbering amp Port Selection Port ID numbering and Port Selection follow the method used by the KVM switch connected to the CL3000 Consult your KVM switch s User Manual for details Chapter 3 Operation Hotkeys Console selection on the CL3000 is accomplished with hotkey combinations as described in the following table Combination Action Ctrl Alt Shift P C Enter To select normal mode pc etc Ctrl Alt Shift M A C Enter To select Mac Ctrl Alt Shift S U IN Enter To select SUN Ctrl Alt Shift u p g r a d e Enter Activates the Firmware Upgrade Mode Note this Hotkey sequence only works when the Firmware Upgrade Recovery Switch see page 22 is in the Normal position Ctrl Alt Shift L Enter Enable Local LED backlit LCD console Disable Remote external console Ctrl Alt Shift R Enter Enable Remote external console Disable Local LED backlit LCD console Ctrl Alt Shift L R Enter or Ctrl Alt Shift R L Enter Enable both consoles default Ctrl Alt Shift U M Enter Configures the front USB Port to mouse mode Mouse funct
26. set s Type A USB connector to a USB port on the computer 3 Atthe other end of the cable set connect the SPHD connector to the KVM port of the CL3000 21 CL3000 User Manual Firmware Upgrade Mode The CL3000 s firmware upgrade mode can be accessed one of two ways by entering a hotkey sequence see Hotkeys page 19 or by placing the CL3000 in firmware upgrade recovery mode see Firmware Upgrade Recovery page 26 Note In order to activate the Firmware Upgrade Mode using a hotkey sequence the Firmware Upgrade Recovery Switch see page 6 must be set to the Normal position 1 Turn off the power to the CL3000 using the power switch located on the back side of the console 2 Slide the firmware switch to NORMAL see page 6 3 Turn on the power to the CL3000 using the power switch located on the back side of the console When the CL3000 is in Firmware Upgrade Mode the Num Lock Caps Lock and Scroll Lock LEDs will continually flash on and off To exit the Firmware Upgrade Mode see Exiting Firmware Upgrade Mode page 26 22 Chapter 4 The Firmware Upgrade Utility Starting the Upgrade To upgrade the firmware 1 Run the downloaded firmware upgrade package file either by double clicking the file icon or by opening a command line and entering the full path to it The Firmware Upgrade Utility welc
27. t takes two people to mount the console one to hold it in place the other to screw it in 2 The standard rack mounting kit does not include screws or cage nuts If you need additional screws or cage nuts contact your rack dealer 3 Optional mounting kits including single person Easy Installation kits are available with a separate purchase CL3000 User Manual To rack mount the console do the following 1 While one person positions the CL3000 in the rack and holds it in place the second person loosely screws the front brackets to the rack 2 While the first person still holds the CL3000 in place the second person slides the L brackets into the CL3000 s side mounting brackets from the rear until the bracket flanges contact the rack then screws the L brackets to the rack 3 After the L brackets have been secured tighten the front bracket screws Note Allow at least 5 1 cm on each side for proper ventilation and at least 12 7 cm at the back for the power cord and cable clearance Chapter 2 Hardware Setup Connecting Up Refer to the installation diagram on the following page as you perform the installation steps The numbers in the diagrams correspond to the numbers of the steps 1 Plug the SPHD connector end of the KVM cable provided with this unit into the CL3000 s KVM port 2 Plug the keyboard monitor and mouse connectors of the KVM cable into their respective ports in the Console
28. ta eee ei eee ede ix Product Information ix Chapter 1 Introduction OVEIVIEW ner AD LE eee ee ei 1 The Benefits of LED backlit LODSs 1 Feature Sk ccd 4 000 be Raat ad ie herd hg ety tan ee 2 Requirements anie 2 Sas de ees yee Ee See Sie 3 LED backlit LCD Console 3 External Console sr d una eee ae 3 Cables sr ee be hartley eae a nee oN Bs 3 Operating Systems 4 GOMBONENIS er rear ee rae hd aes 5 Front View s oi binder dare ben tee Dr aoe ee nern 5 Rear VOW sd ees oe eek Rea ea he sce pe A A 7 Chapter 2 Hardware Setup Before you Begin dra ee ai Beebe ee ie ta ee 9 Standard Rack Mounting 9 Connecting Up 11 Chapter 3 Operation Opening the Console 13 Closing the Console 14 Operating Precautions i 15 LED backlit LCD OSD Configuration 16 LED backlit LCD Buttons 16 Adjustment Settings 17 Manufacturing Number 17 Hot PIUggiIng sis hin ek Ss en en tiens range ut rer 18 Powering Off and Restarting 18 vi CL3000 User Manual Hotkeys ke RR ee 19
29. tails 5 LED backlit LCD Push this button to turn the LED backlit LCD monitor on and On Off Button off The button lights when the LED backlit LCD monitor is off Note The light indicates that only the monitor is off not the attached KVM switch 6 Keyboard Module Standard 105 key keyboard 7 Touchpad Standard mouse touchpad 8 USB Port The USB port is available to connect a USB peripheral device flash drive CD ROM drive etc to the console or a USB mouse for users who prefer to use an external mouse 9 Power LED Lights blue to indicate that the unit is receiving power 10 Rack Mounting Rack mounting tabs are located at each corner of the unit Tabs See Standard Rack Mounting page 9 for details 11 Lock LEDs The Num Lock Caps Lock Scroll Lock LEDs are located here 12 Reset Switch Located to the right of the Lock LEDs Press this recessed switch in with a thin object to perform a system reset 13 Firmware During normal operation and while performing a firmware Upgrade Switch upgrade this switch should be in the NORMAL position If a firmware upgrade operation does not complete successfully this switch is used to perform a firmware upgrade recovery See Firmware Upgrade Recovery page 26 for details 14 LED Illumination Press the Exit Light pushbutton for two seconds to turn the Light LED light ON or Off Default On Chapter 1 Introduction Rear View
30. ting through the menus this button moves you Left or Down When making an adjustment it decreases the value EXIT When you have not entered the LED backlit LCD OSD Menu function pressing this button performs an auto adjustment An auto adjustment automatically configures all the settings for the LED backlit LCD panel to what the OSD considers their optimum values to be When you have entered the LED backlit LCD OSD Menu function pressing this button exits the current menu and returns you to the previous menu Use it to leave an adjustment menu when you are satisfied with the adjustment you made When you are at the Main Menu pressing this button exits the LED backlit LCD OSD 16 Chapter 3 Operation Adjustment Settings An explanation of the LED backlit LCD OSD adjustment settings is given in the table below Setting Explanation Brightness Adjusts the background black level of the screen image Contrast Adjusts the foreground white level of the screen image Phase If pixel jitter or horizontal line noise is visible on the display your LED backlit LCD may have the wrong phase setting Adjust the phase setting to eliminate these problems Clock If vertical banding is visible on the display your LED backlit LCD may have the wrong clock setting Adjust the clock setting to eliminate vertical banding H Position Positions the display area on the LED backlit LCD panel horizontally m
31. to the rack extended to the floor and that the full weight of the rack rests on the floor Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack Always load the rack from the bottom up and load the heaviest item in the rack first Make sure that the rack is level and stable before extending a device from the rack Use caution when pressing the device rail release latches and sliding a device into or out of a rack the slide rails can pinch your fingers After a device is inserted into the rack carefully extend the rail into a locking position and then slide the device into the rack Do not overload the AC supply branch circuit that provides power to the rack The total rack load should not exceed 80 percent of the branch circuit rating Make sure that all equipment used on the rack including power strips and other electrical connectors is properly grounded Ensure that proper airflow is provided to devices in the rack Ensure that the operating ambient temperature of the rack environment does not exceed the maximum ambient temperature specified for the equipment by the manufacturer Do not step on or stand on any device when servicing other devices in a rack Caution Slide rail LED backlit LCD LCD KVM mounted equipment is not to be used as a shelf or a work space 29 CL3000 User Manual Technical Support International For onl
32. to the wall outlet does not exceed 15 amperes To help protect your system from sudden transient increases and decreases in electrical power use a surge suppressor line conditioner or un interruptible power supply UPS Never push objects of any kind into or through cabinet slots They may touch dangerous voltage points or short circuit parts resulting in a risk of fire or electrical shock Do not attempt to service the device yourself Refer all servicing to qualified service personnel If the following conditions occur safely remove the power to the wall outlet then unplug the device and bring it to qualified service personnel for repair The power cord or plug has become damaged or frayed Liquid has been spilled into the device The device has been exposed to rain or water The device has been dropped or the cabinet has been damaged The device exhibits a distinct change in performance indicating a need for service The device does not operate normally when the operating instructions are followed Only adjust those controls that are covered in the operating instructions Improper adjustment of other controls may result in damage that could require extensive work by a qualified technician to repair Do not connect the RJ 11 connector marked UPGRADE to any type of telephone network 28 Appendix Rack Mounting Before working on the rack make sure that the stabilizers are secured
33. urface bed sofa rug or other soft surface as this will block its ventilation openings Likewise the device should not be placed in an enclosure unless adequate ventilation has been provided Never spill liquid of any kind on the device Unplug the device from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning The device should be operated from the type of power source indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company The device is designed for IT power distribution systems with 230V phase to phase voltage To prevent damage to your installation it is important that all devices are properly grounded The device is equipped with a 3 wire grounding type plug This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not attempt to circumvent the purpose of the grounding type plug Always follow your local national wiring codes Do not allow anything to rest on the power cord or cables Route the power cord and cables so that they cannot be stepped on or tripped over 27 CL3000 User Manual If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating Make sure that the total of all products plugged in
34. with this product can be connected Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and especially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquiries please contact your direct vendor 37 CL3000 User Manual This Page Intentionally Left Blank 38 C CL5708 CL5716 Overview 1 CL5708D CL5708E Specifications 31 Components 5 Console Selection 19 F Features 2 Firmware upgrade Mode 22 recovery 26 Front View 5 H Hot Plugging 18 Installing 11 K Keyboard Emulation 36 L LCD Buttons 16 OSD configuration 16 O Online Registration iv Operating Precautions 15 P Port ID Index Numbering amp Selection 18 Powering Off 18 Precautions 15 R Rack Mounting Optional 32 Safety information 29 Standard 9 Rear View 7 Requirements Operating systems 4 Reset Switch 6 Restarting 18 RoHS ii S Sa
Download Pdf Manuals
Related Search