Portable Bluetooth 2” Thermal Printer User's Manual V1
Contents
1. 3 4 PRINTER INTERFACE CONNECTION AND PRINTING 3 4 1 RS 232 SERIAL INTERFACE The optional accessories for printer include DB 9 serial interface cable one end is D model standard serial interface socket connected to host computer the other end is PS 2 socket connected to printer When connect the serial interface if it works normally then the printer stops to received data from Bluetooth interface The serial interface of the printer is RS 232 the baud rate range is 1200bps 2400bps 4800bps 9600bps 19200bps 5 600bps 115200bps 3 4 3 BLUETOOTH CONNECTION PDA Laptop and other communication devices with Bluetooth can drive printer to print by the Bluetooth interface printer BT is compatible with Bluetooth 2 0 protocol Power grade is CLASS 2 effective communication distance is 10 meters The name of the printer is printer the initial password is 0000 The method for the pairing between printer with the host device is Turn on the printer Host device searches for the outer Bluetooth device If there are other Bluetooth devices please select BT PRINTER Put in password 0000 Pairing finished oR WN Notice If the printer name has been changed please be sure not turn on more than one printer otherwise it will be difficult to justify which printer been paired 3 5 INDICATORS AND BUZZER There are three indicators for printer printer they are MODEX FEED and POWER indicator The following is the me2. red color e Battery full charge time 4 hours e Battery duration under 25 print density at least 100 meters the standby time is over 15 days Chapter 3 Operation 3 1 USING PREPARATION 3 1 1 BATTERY INSTALLATION 3 1 2 PAPER INSTALLATION 3 1 3 BUCKLE INSTALLATION WITH SNAP RING amp HOLSTER F 3 2 Operation Specifications 3 2 1 PRINTER ON The printer is powered on by pressing the power button the power indicator is on with green color whenever the printer is on Notice when the batter is almost exhausted the power indicator blinks with red color in this case you must charge the battery by using the adaptor The method of charging the battery please refer to 3 2 5 3 2 2 PRINTER OFF The printer is off after hold down the power button All the indicators are off whenever the printer is off 3 2 3 SELF TEST The self test checks the printer s current settings status and whether the printer has any problems Turn on the power while holding down the FEED button the self test begins The printer is ready to receive data as soon as it completes the self test 3 2 4 PAPER FEEDING When the printer works normally hold down FEED button the paper feeding begins and stops when hold down FEED button again When the printer works in black mark mode hold down FEED button the printer begins to feed paper and stops at the position of black mark If the paper is not black mark paper the printer will not stops
3. work improperly If print with serial interface should not unplug the interface cable in the course of printing or else some printing data may be lost When print with Bluetooth interface the communication distance should be within 10 meters otherwise the printer doesn t print or prints rubbish codes Too high 50 C pr too low 0 C temperature and too high 85 or too low 20 relative humidity both effect the print quality The print paper in poor quality or stored for too long time also may reduce the print quality even damage the printer In the black mark detecting mode the printer requires that the ready print black mark is accordant with the black mark printing rules details please refer to Chapter 5 otherwise the black mark can not be detected correctly Be sure to use up the electricity of the battery before charge it as it can ensure the using life of the battery 0 3 NOTES ON HANDLING The printer should be placed in such an environment that the temperature is between 20 Cand 60 C and the relative humidity is between 5 and 95 If the printer will be stored for a long time pleas be sure to take out the battery otherwise may damage the battery and printer Normal thermal paper can t be kept too long if you need to keep the receipt for a long period please choose long term effective thermal paper The print paper should be keep away from high temperature environment and point blank sunshine Chapter 1
4. Outer Appearance and Model 1 1 Standard Package 1 2 Option Accessories Snap Ring Can be used with or without Holster Chapter 2 General Specifications 2 1 PRINTING SPECIFICATIONS Print method thermal line printing Paper width 58mm Print width 48mm Resolution 8 dots mm 203dpi 384 dots line 2 Print speed 60mm sec e Paper thickness 60 80um Character Alphanumeric characters extended graphics international characters 1D Barcode EAN13 Code 39 CODE128 2D Barcode PDF417 By WINDOWS XP DLL 2 2 PHYSICAL SPECIFICATIONS e Outline dimension 75x105x46mm e Weight 261g including paper roll and battery e Paper roll diameter lt 4Qmm e RS232 serial 1200bps 115200bps The RS 232 cable is optional e Bluetooth Wireless Interface Default 2 3 ENVIRONMENTAL CONDITIONS e Operation temperature 0 C 50 C Relative humidity 20 85 e Storage temperature 10 C 70 C Relative humidity 5 95 2 4 OTHER FEATURES e Paper loading method drop in easy loading details please refer to 3 1 2 Paper Installation e Black mark localization available details please see Command Set and Chapterd e Paper out detection when paper is out the FEED button indicator blinks Yellow LED e Print commands ESC POS compatible command set refer to Chapter 4 e Power supply 1400mAh rechargeable polymer lithium battery e Low power alarm when the battery is low the power indicator blinks with
5. Portable Bluetooth 2 Thermal Printer User s Manual V1 0 Model BT TP2 Chaper 0 Operating Precautions This section presents important information intended to ensure safe and effective use of the printer Please read the following carefully 0 1 NOTES ON SAFETY Be sure to use the specified battery and power source provided by our company Connection to an improper power source may cause fire explosion or damage to the printer Don t put the battery into the fire or water don t disassemble or modify the battery don t be short circuit otherwise may result in injury or fire even explosion If the printer would not be used for a long time be sure to take off the battery otherwise the battery may leak liquid which is corrosive if improper operation causes battery leak and the liquid is spattered on the skin or clothes please wash it with water if spattered in the eyes please rinse them with water thoroughly and see a doctor Please do not open the paper case cover when it is printing or just when printing is over do not touch the print head with hand or body overheat may cause scald 0 2 NOTES ON USING Be sure not to print continuously over 1 meter otherwise may cause damage to the print head Water or other liquid should not spill into the printer also the printer should not be appeared in the rain or else may cause printer damage Please do not open the paper case cover when it is printing otherwise the printer may
6. aning of each indicator denotes MODE indicator Blink Blue Bluetooth active but yet connection Solid Blue Data transmission connection ready Green LED blinking twice high temperature error FEED indicator Blink Orange Paper out Cover open POWER indicator Solid GREEN power on Solid RED low battery Solid RED while charging Light off Full charging begins from power off status Chapter 4 Printing Control Commands The printer adopts ESC POS compatible commands the command table is the printing commands They are classified according to their functions Please Refer to Command Set CHAPTER 5 BLACK MARK DETECTION lf user uses ready printing black mark to localize the receipt please be sure to abide by the following black mark ready printing regulation when print the black mark otherwise the black mark can t be recognized by the printer The black mark ready printing regulation Print position as the following figure shows the black mark should be printed on the right of the word side Width range 27mm Height range 4mmsheights6mm Reflectivity to infrared ray lt 10 the reflectivity of the other parts of the paper black mark width to infrared ray gt 65 HPS 4 5mmsHpss6 5mm
7. until release FEED button 3 2 5 BATTERY CHARGING The power indicator becomes red when the power of the battery is run out so charging the battery is required in this situation The charging method is as following turn off the printer connect the adapter to the power socket with 110V 220V 50HZ then plug the power charging cable to the power socket of the printer so the power charging begins During the course of power charging the Power indicator goes red and becomes turn off when the charging is over Notice it would better not turn on the printer during the course of charging power lest the charging time goes longer moreover be sure not to use the printer to print when the battery is charging The adapter voltage may not afford the power exhaust while printing activation When the battery is low the power indicator blinks with red color In this case you must charge the battery by using the adaptor Charging battery method The printer uses a Lithium rechargeable battery pack Before first use the battery pack should be charged for at least 4 hours To prevent electrical damage to the printer and or battery pack please use approved AC DC adapter only During charging the POWER indicator is red and when the battery is charged fully the POWER indicator is turned off 3 3 PRINTER SETTING You can transfer instruction through the computer to set the printer Related information please refer to instruction that
Download Pdf Manuals
Related Search