NDT/RT Film Digitizer User's Manual
Contents
1. Output Basket MII 900 Plus User s Manual 21 Installing Your Film Digitizer Installing the Software Important You must install software before connecting your digitizer Always close any open programs and turn off Anti virus utilities before installing software 1 Turn on your computer 2 Place the Microtek CD into your CD ROM drive 3 Follow the on screen instructions to install the driver and software NOTE If the Microtek Software Installer screen does not come up automatically double click the following in succession My Computer the CD ROM icon then cdsetup exe to start the installer program 4 Click EXIT on the Microtek Software Installer screen when all the software have been installed 5 Restart your computer 22 MII 900 Plus User s Manual Connecting the Film Digitizer To the Power Cord 1 Connect the power cord to the left side of the digitizer 2 Plug one end of the power cord into a wall outlet or other power source To the Hi Speed USB Cable 3 Connect one end of the Hi Speed USB cable to your computer 4 Connect the other end of the Hi Speed cable to the digitizer s USB port locating at the left side of the digitizer MII 900 Plus User s Manual 23 5 Locate the hook of the Light Shield at the top of the Front Cover of the scanner Pull it up to raise the Light Shield2. Hook of the Film Shield 6 Turn the power switch at the front left panel of the digitizer to On once the scanner is detected by your system the LED lights on the front panel will brighten and the digitizer is ready to scan 24 MII 900 Plus User s Manual Using Light Shield to Digitize Industrial RT X ray Film A light shield is a tool equipped in your MII 900 Plus used to block out unnecessary light when scanning It can help to improve the dynamic range for final scanned images However the maximum limit for the width of the Light Shield is about 10 24 inches 26 cm If the your scanned target is wider than the maximum limit of the Film Shield please do not use the Light Shield Attaching Light Shield into Guide Arms Before using the Light Shield you have to fasten it into Guide Arms on the Input Tray Follow the steps below 1 Locate the hook of the Light Shield at the top of the front cover of the digitizer Use it to pull the Light Shield up Hook Fastenings 2 Slide the two Guide Arms toward the Light Shield Align the Guide Arms with the Light Shield properly MIlI 900 Plus User s Manual 25 3 Move down the Light Shield Make sure that two fastenings of the Light Shield are attached to protruding parts at the bottoms of Guide Arms t
3. To scan 8 5 x 4 5 industrial film use the 8 5 x 4 5 Film Holder which can hold up to one pieces of the 8 5 x 4 5 industrial RT X ray film at a time 1 Install the Feed Tray onto your digitizer before using it Refer to the front sections Installing the Feed Tray for the detail Feed Tray 2 Load the film face up inside the holder Slide the film along the slot of the holder until the film is fully loaded 3 Load and insert the 8 5 x 4 5 Film Holder with loaded film into the Feed Tray with the side to be scanned facing up and with the top of the film directing upwardly Push the holder into the tray until the edge of it touches the bottom edge of the Feed Tray Make sure that the Light Shield has been pull up Microtek logo 30 MII 900 Plus User s Manual B Using the 12 x 3 1 3 Film Holder To scan 12 x 3 1 3 industrial film use the 12 x 3 1 3 Film Holder which can hold up to one piece of the 12 x 3 1 3 industrial RT X ray films at a time 1 Install the Feed Tray onto your digitizer before using it Refer to the front sections Installing the Feed Tray for the detail 2 Load the film face up inside the holder Slide the film along the slot of the holder until the film is fully loaded Feed Tray 3 Load and insert the 12 x 3 1 3 Film Holder with loaded film into the Feed Tray with the side to be scanned facing up and with the top of the film dire
4. more details 1 Follow the procedures for Positioning Industrial RT X ray Film with the Light Shield to load the film into the digitizer s Feed Tray 2 Launch ScanWizard Industry either as a stand alone by clicking the program icon or by using the File Import or Scan command from an application program Note If it is your first time to turn on the digitizer and to launch the program if the Calibation information Light Shield is not pull up the program Pease beba fd nei ae will prompt a window to remind you l Bring up the Light Shield and click the Calibration button Then the scanner will start to calibrate When the calibration is done click the OK Calibation information button to bring in main windows of Microtek Scan Wizard Industry XX ScanWizard Industry program Calibration is done 3 Click the Overview button to perform a preliminary scan of the image which will appear in the Preview window 4 Select your image output type in the Type Type y Gray Scale drop down menu Gray Scale 16 bit Select Gray Scale to scan the image in 8 bit grayscale This is also the default setting of the software program Select Gray Scale 16 bit to scan the image in 16 bit grayscale 5 Select your desired image output resolution in the Resolution drop down menu The default setting is 300 dpi Res 6 Select the Scan Frame tool from the Toolbar in the Preview window and choose t
5. reduces energy costs amazingly With its stable performance the image quality will remain consistent even after used for a certain period of time e Support various sizes of X ray films The MII 900 Plus covers the scanning of all standard RT X ray film sizes from 2 5 x 2 5 to 14 x 52 which offers more flexibility to digitize X ray films e Exclusive Film Holders These specially designed industrial film holders are used to hold films in place By loading industrial film holders with loaded films before scanning you can ensure perfect alignment of your scanned images and achieve consistent scans Two types of industrial film holders provided they are 8 5 x 4 5 and 12 x 3 1 3 e Fast scanning speed The MII 900 Plus increases your productivity with fast scanning speed of 18 seconds or less at 300 dpi for a grayscale scan of 14 x 17 film e Hi Speed USB USB 2 0 port Hi Speed USB USB 2 0 is capable of high data transfer rates of up to 480 Mbit sec e Easy to operate clean and maintain The MII 900 Plus requires virtually no routine maintenance and no daily cleaning which is ideal for radiographic inspection industry e Microtek ScanWizard Industry software The friendly user interface of ScanWizard Medi converts X ray films in a computer readable format offering an easy and quick access and management Auto crop This feature automatically crops the scan frame to fit the size of the original film when
6. scanning film with provided film holders MII 900 Plus User s Manual 9 Auto density This feature enables the digitizer to optimize the image density automatically when scanning a X ray film It automatically defines the lightest and darkest pixels in a scanned image and then redistribute the intermediate pixel values proportionately Customized exposure This manual setting tool allows you to customize an exposure time for the scanned image It enhances the visibility of extreme dark film delivering a better scanning result and improving the quality of saved files System Requirements In order to use your MII 900 Plus your computer must satisfy the following system requirements CD ROM drive for installing software Color display with 24 bit color output capability 4GB RAM or more Pentium IV PC or higher with Hi Speed USB USB 2 0 port Windows XP Windows 7 64 bit and Windows 8 64 bit 10 MII 900 Plus User s Manual Unpacking Your Film Digitizer Looking for Damage While unpacking your digitizer inspect the shipping carton for any signs of mishandling or damage The digitizer s packing carton and padding material have been carefully chosen to prevent damage to the unit in shipping and can withstand a reasonable amount of pressure After unpacking your digitizer package refer to the later section to ensure that you received all of the parts necessary for digitizer setup If there are any damag
7. the digitizer from the bottom foam support Then remove the digitizer from the wrapped plastic bag MII 900 Plus User s Manual 13 Package Contents After you have unpacked your digitizer package please check for the major components listed below Accessory Box 1 MII 900 Plus Film Digitizer Accessory Box 2 Accessories for Box 1 Es E Output Guide Feed Tray Power Cord 14 MII 900 Plus User s Manual Oe ee RN RE N Accessories for Box 2 8 5 x 4 5 Holder cuore l gt 12 x 3 1 3 Holder T EE E ES SS N EE S SS EA MII 900 Plus User s Manual 15 How to Repack Your Film Digitizer for Shipping To ship back your MII 900 Plus for repairing maintenance services or other reasons in order to not damage your MII 900 Plus it is strongly recommended that using the original carton and other packing materials Follow the steps below to repack your MII 900 Plus correctly 1 Wrap the digitizer with the plastic bag and then insert it into one foam support 2 Cover down the other foam support on the tops of the digitizer 16 MII 900 Plus User s Manual 3 Turn over the foam supports and insert SR other two accessory boxes into the both sides of the foam supports 4 With both hands hold the two sides of foam suppo
8. with your digitizer there is a separated Feed Tray which holds the X ray films to be fed into the digitizer Before using the Feed Tray with your digitizer you need to assembly it onto the digitizer Follow the instructions and graphs below to correctly install the Feed Tray 1 Look for two sets of the Feed Tray Holes at both ends of the front top of the digitizer 2 Insert and push down both sides of the Feed Tray into its compartment holes making sure the Feed Tray snaps into place Feed Tray 20 MII 900 Plus User s Manual Installing the Output Tray Coming with your digitizer there are two kinds and separated Output Trays which store the stacked X ray films which have been digitized One of them is called Output Guide used to guide the digitized materials staying on the table The other is called Output Basket used to store and keep the digitized materials in a basket You may use only one of them as an output tray at a time Before using them with your digitizer you need to assembly them onto the digitizer 1 Look for two sets of Output Tray Holes at both ends of the front bottom of the digitizer 2 Insert and push down both sides of the Output Guide into its compartment holes making sure the Output Guide snaps into place Or Insert and push down both sides of the Output Basket into its compartment holes making sure the Output Basket snaps into place Output Guide
9. 14 x 52 355 6 mm x 1320 8 mm 1 00 000 times at 300 dpi scan cycle 100 000 scans or 5 years Hi Speed USB USB 2 0 10 2 x 18 7 x 9 3 260 mm x 474 mm x 235 mm 19 82 Ibs 9 kg AC 100V to 240V 47 63 Hz 1 5A Max Input 54 9 W Max Operating temperature 50 to 104 F 10 to 40 C Relative humidity 20 to 85 Storage temperature 14 to 140 F 10 to 60 C Relative humidity 20 to 95 Specifications software bundles and accessories are subject to change without notice Not responsible for typographic errors 42 MII 900 Plus User s Manual
10. MICROTEK 1 900 NDT RT Film Digitizer User s Manual Preface Copyright 2015 Microtek International Inc all rights reserved This document may not be reproduced or copied in any way stored electronically or translated into any language without the permission of Microtek International Inc Trademarks Microtek ScanMaker ArtixScan ScanWizard and ColoRescue are trademarks or registered trademarks of Microtek International Inc All other trademarks or registered trademarks are the property of their respective holders Specifications software and hardware bundles are subject to change without notice Not responsible for typographical errors Disclaimer The contents of this manual have been checked carefully for accuracy and every effort has been made to ensure that there are no errors However Microtek makes no guarantee as to the accuracy of the contents of this document and reserves the right to make changes to the contents without prior warning 149 004974 B March 2015 Microtek International Inc No 6 Industry East Road 3 Science Based Industrial Park Hsinchu 30075 Taiwan Tel 886 3 5772155 Fax 886 3 5772598 http www microtek com 2 MII 900 Plus User s Manual FCC Compliance Statement This equipment Model MSS 2400XU2L has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reason
11. a teens 23 TO the Power COR sareari nianie nanana anaa piana 23 To the Hi Speed USB Cable ssssssssssssressressrersrrrsrnrsrsrerererersserere 23 Using Light Shield to Digitize Industrial RT X ray Film 25 Attaching Light Shield into Guide Arms iiciiis iii ee eee ee neta eens 25 Positioning Industrial RT X ray Film with the Light Shield 26 Scanning Industrial RT X ray Films is iss ienes 27 MII 900 Plus User s Manual 7 Using Film Holders to Digitize Industrial RT X ray Film 30 Positioning Your Industrial RT X ray Film cccececeeeee eee siso 30 A Using the 8 5 x 4 5 Film Holder cccceceseeeeeeeeeeeeeeeenes 30 B Using the 12 x 3 1 3 Film Holder ccccccceeeeeeeeeeeeeeneeeees 31 Scanning Industrial RT X ray Films cece eee cece e eee eee eee teense enes 32 Digitizing Industrial RT X ray Films in Other Sizes 33 Positioning Industrial RT X ray Film ccc ccceeeee cece eee eee eee eee ee ea tees 33 Scanning Industrial RT X ray Films 21 0 0 cece cece eee eee eee teeta ee enee 35 Care and Cleaning sicisecccccccccccccscsscccascscscsscacascaasicacscascssssaccsscsecstecceess 36 Cleaning the Glass Surface on the Digitizer ccceecee eee eee eee ee ee ee 36 Cleaning the Glass and Components on the Front Cover 37 Cleaning the Rollers a esa ssaiss cean
12. able protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorientor relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Note A shielded Hi Speed USB interface cable with ferrite core installed on the film digitizer connector end must be used with this equipment Caution Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired op
13. cting upwardly Push the holder into the tray until the edge of it touches the bottom edge of the Feed Tray Make sure that the Light Shield has been pull up Microtek logo MII 900 Plus User s Manual 31 Scanning Industrial RT X ray Films 1 Follow the procedures for A Using the 8 5 x 4 5 Film Holder to load the industrial film into the digitizer s Feed Tray 2 Follow the procedures steps 2 through 8 for Scanning Industrial RT X ray Films to launch the ScanWizard Industry software to specify your scanning requirements and to start scanning e In step 6 instead select the correct Scan Frame 8 5 x4 5 ao ca holder size to be used and scanned in the Scan Frame drop down menu You will see a flashing frame marquee Add To Menu around the selected area Remove Settings pleecanhjzaro ne DA Scanner View Correction Help Job Unittiedt Overview i Scan F tReet Oray Soale De a i 0 Res 300 v ppi 0 0847mm E O Scan Frame Wi 1200 H 333 Image Size 3 513 KB DO Settings window Scan frame enclosed by red dotted lines al lt gt MICROTEK ore press CTRL key to keep aspect ratio selection or press SHIFT key to Preview window 32 MII 900 Plus User s Manual Digitizing Industrial RT X ray Films in Other Sizes If your scanned target cannot be used together with the Light Shield wider than 10 24 or
14. d Use a dust blower or lint free cloth to clean components inside the hollow part under the glass 5 After cleaning the glass and the components along the tracks push back the glass surface until it snaps into place 38 MII 900 Plus User s Manual Cleaning the Rollers Prolonged used of the digitizer may result in accumulation of ink and other residue on the feeder s rollers affecting their efficiency Clean the rollers periodically to maintain performance Rollers are found in two areas of the MII 900 Plus Directly on the digitizer and on the side of the front cover To clean the two sets of rollers 1 Push down two buttons at both sides of the front cover of the digitizer and open the front cover When opening the front cover support the both sides of the front cover with your hands avoiding suddenly falling down of the front cover 2 Clean the rollers with a lint free cloth or a swab moistened with alcohol or ECO cleaner as shown in the graphic below Remember to clean the rollers on the digitizer and the front cover at the same time Rollers on the digitizer Rollers on the front cover of the digitizer Maintenance After usage for a period of time the parts inside your digitizer such as rollers or light source may become worn out and a problem such as insufficient light supply may occur In this cases contact your local dealers or wholesales for the maintenance services Note Your digiti
15. ed or missing parts notify the shipper immediately or contact customer service NOTE Save the carton and all packing materials If you need to ship the digitizer later it is recommended that you should repack it using the original wire ties plastic bags foam supports and cartons which protects your digitizer from unnecessary damage Refer to the later section How to Repack Your Film Digitizer for Shipping for the detail Unpacking Package Contents After unpacking the shipping carton follow the steps shown below to take out your digitizer and other accessory components 1 Ensure that you put your shipping carton toward the right direction Then lift up the A top cover MII 900 Plus User s Manual 11 2 Remove each cardboard from four sides of the shipping carton 3 With both hands hold the two sides of foam supports and then lift up the foam supports firmly from the carton Before putting down the package on a steady surface do not go off either of hands from holding the foam supports Note The package of the contents is heavy almost 33 pounds Due to the heavy weight of the package about 33 pounds make sure you can handle it properly before removing it from the carton 4 Remove two accessory boxes 1 and 2 from the foam supports 12 MII 900 Plus User s Manual 5 Turn over the foam supports and make them stand vertically 6 Lift up the upper foam support 7 Pull out
16. er C Send image to application after saving a Adobe Photoshop e If ScanWizard Industry is launched as a Plug In from an application program the scanned image is delivered after the scan to your application where the image can be saved viewed or printed further Note When scanning with the Light Shield if the scan frame covers the area of the Light Shield the selected area of the Light Shield will be cropped out automatically and will not appear in the saved image file If the scanned image is too big more than 200 MB a message will appear on the screen to notify you that the selected area of the Light Shield will not be cropped out instead it will be filled with blanks 28 MII 900 Plus User s Manual Untitled Gray Scale ppi 0 0847mm 7 96 H 4 076 KB Scan frame enclosed by red dotted lines 0 1 85D Settings window K While selecting press CTRL key to keep spect ratio selection Preview window MII 900 Plus User s Manual Using Film Holders to Digitize Industrial RT X ray Film Come with the digitizer package there are two types of holders 8 5 x 4 5 Film Holder and 12 x 3 1 3 Film Holder Use the holder that correctly matches the film size to be scanned The use of the individual industrial film holder is explained in the succeeding pages of the manual Positioning Your Industrial RT X ray Film A Using the 8 5 x 4 5 Film Holder
17. eration MII 900 Plus User s Manual 3 CE Compliance Statement This device complies with CE Certification pursuant to EN 55011 2007 A2 2007 EN 60601 1 2 2007 WEEE Compliance Statement Microtek International Inc operates under full compliance with the WEEE Directive Among the requirements of the Directive are the marking of any applicable equipment placed in the EU market with the WEEE symbol a crossed out wheeled bin as shown at left demonstration of the implementation of a take back program and meeting recycling targets ISO Compliance Statement Comply with the requirements of the international quality standard ISO 9001 2000 and ISO 13485 2003 4 MII 900 Plus User s Manual Safety Precautions Before using your digitizer read the following safety guides carefully which detail the proper operation of the digitizer and its accessories to prevent injuries or damage to users or equipment Meanings of Symbol Signs This indicates hazardous situation which if not payed CAUTION attention could result injury or damage to users or equipment J This indicates hazardous situation which if not payed WARNING attention could result serious injury or death to users Power Supply A e Use a power source only with a power rating specified on the marking label A AN e Ensure to turn off the power of each device before connecting or disconnecting the cables N AN e Insert the plug completely into the ou
18. fety PrecautionS ssitrsea on nia a E E E a ces 5 Knowing about Your Film Digitizer 2 2 0 ceeeeeeeeeeeeeeeeeneeeeeeeeeeeeee 9 Features of th MII 900 PIUS scccscenceadsatince ceseededvanerecese da eradasi pusaaaac minado 9 System Requirements ssiri ienris partie nas ianhesda aaa 10 Unpacking Your Film Digitizer o nono 11 LOOKING FOF Damage smasausasi van epsnmicasaesicaansaMic e nsiado asas nadas icaamazinia 11 Unpacking Package Contents sis ee ee eats tana eneeaenes 11 Package Contents usansxasauada pras spaicioasassa casas Sica snsiace nda EA Ea 14 How to Repack Your Film Digitizer for Shipping 16 Taking a Closer LOOK 2 c0sceceeceeeeeeeeeeeeeeeeeeeeaeeeseeeeeaeeseeeeeeeeeeeeeees 18 Front Top Bottom View asscassasassa sa ainicssaassemas pisa noa asia me saia nas aad dia 18 Rear Side VIEW resensente ini Masai ria mad anal uia das Saad isa dana 19 Assembling Your Film Digitizer nono on ooo nnno 20 Installing the Feed Tray ccccceeee eee iss tenet eens ee eeeee nae eee ea eneneee 20 Installing the Output Tray ccceee cece eee eee eee eee terete neta eee eaten eae 21 Installing Your Film Digitizer 2 22222cececeeeeeeeeeee seen eee cece eeeeeeeeeeeeee 22 Installing the SOTW AE aa usiasi nasais ainsi anana anaa a aeaa 22 Connecting the Film Digitizer ccecece cece eect eee eee eee eee e net
19. he area to be scanned by dragging a rectangle around it You will see a flashing frame marquee around the selected area MII 900 Plus User s Manual 27 7 If necessary click Darkness to choose a predefined exposure setting for the current scan job enhancing the visibility of dark areas ooo e Type Gray Scale x Res 30 ppi Ooa Scan Frame W 1200 H 333 Image Size 3513 KB 1 If you want to customize an exposure setting for the current scan job choose Adjust from the Darkness drop down menu and then point your mouse to its edit box Choose a desired setting by clicking the left right arrow from its available settings Optimization Darkness 7 ar w Adjust 1 10 Add to Menu Default Click the Scan button on the control panel to start scanning at z Industry e If ScanWizard Industry is launched as a y Microtek ScanWizard Industry Save As Images stand alone program a window Save ESSET E Mine es As dialog box will appear Click the ite Save button then the scanned image Soom can be saved into your selected folder Imagenooos tr or sent to your selected application Filename mage00006 To view the scanned image double E 7 click the Industry Images icon on lta rene your desktop default folder assigned Topi bia by the software or retrieve it from cet E your assigned fold
20. ightly If the Light Shield and Guide Arms are jointed successfully they can be moved together by sliding Guide Arms Positioning Industrial RT X ray Film with the Light Shield MII 900 Plus s Feed Tray can hold only one piece of X ray film at a time This section shows you how to position a single sheet of X ray film into the Feed Tray with the aim of the Light Shield 1 Attach the Light Shield into Guide Arms before using it Refer to the front sections Attaching the Light Shield into Guide Arms for the detail 2 Load and insert the film into the Feed Tray with the side to be scanned facing up and with the top of the film directing upwardly A Push the film into the tray until the edge of it touches the bottom edge of the y Feed Tray E 3 Align the film with the center of the z gt o Feed Tray by sliding the two Guide Arms with the attached Light Shield toward the film if the width of the film is less than 10 24 inches Guide Arms with the attached Light Shield 26 MII 900 Plus User s Manual Scanning Industrial RT X ray Films ScanWizard Industry is a scanning software designed by Microtek for Industrial X ray films scanning used for an industrial purpose Its user friendly interface enables you to easily start the scanning process and finish all the scan jobs Refer to the ScanWizard Industry software manual for
21. m your computer and refer to the installation instructions in this document 3 When trying to scan an error message appears on your screen that reads Can t Find Scanners Make sure your digitizer is connected to your computer and plugged in to a power source see Connecting the Digitizer in the Assembling Your Film Digitizer section Uninstall and reinstall the ScanWizard Industry software 4 After clicking Scan a blank screen appears Uninstall and reinstall the ScanWizard Industry software 5 When trying to scan an error message appears on your screen that reads Code 204 Scanning lamp or image sensor circuit failure Please don t select fast preview or draft scan This error message appears when the luminance of lamps is insufficient or surpassed Click OK first then contact the professional technician for the further help MII 900 Plus User s Manual 41 Specifications Type Image Sensor Light Source Scanning Modes Resolution Scanning Area Film Size Lamp Life Product Life Cycle Interface Dimensions L x W x H Weight Voltage Power Consumption Environment Important Sheet feed film digitizer CCD LED Light Emitting Diode Grayscale in a single scanning pass 8 bit grayscale Approx 256 shades of gray 16 bit grayscale Approx 65 536 shades of gray 2400 dpi 14 x 52 355 6 mm x 1320 8 mm Min 2 5 x 2 5 63 5 mm x 63 5 mm Max
22. ources such as radiators heat registers stoves or other products including amplifiers that produce heat N e Do not store the digitizer in which it may be exposed to direct sunlight Using the Digitizer N e Before using the digitizer make sure the area of the front cover is clear from any objects that may cause jams inside A AN e When using the digitizer if your hairs have been jammed into the front cover of the digitizer turn off the power switch immediately Do not attend to remove your hairs from the front cover when the digitizer is still turned on Maintenance and Service e When the digitizer is going to be cleaned ensure to turn off the power of each device and unplug the power cable from the AC outlet e When you need a repair service unplug the digitizer from the power outlet and consult qualified service personnel When replacement parts are required use replacement parts that are specified by the manufacturer or have the same characteristics as the original parts i ie e For safety reasons ensure to inspect the device before using it In addition carrying out a regular inspection at least once a year 6 MII 900 Plus User s Manual Table of Contents Preface TT 2 Safety Regulations ii csececseiiiecccccececancssesceettccecdesiesencscoscevenctecssastensesess 3 FCC Compliance Statement ccccceceeeee cece ee eee ee eee eee aa eana 3 RE QUIATIONS cispra r AE EE EANA ENESA NEARE EEEE 4 Sa
23. ront cover When opening the front cover support the both sides of the front cover with your hands avoiding suddenly falling down of the front cover 2 Using a soft and nonabrasive lint free cloth clean the inner glass surface on the digitizer 36 MII 900 Plus User s Manual Cleaning the Glass and Components on the Front Cover There is one more piece of glass located on the inner side of the front cover of the digitizer To clean it please remove it from the front cover first 1 Push down two buttons at both sides of the front cover of the digitizer and open the front cover Locate the glass on the inner Gisseoaatne side of the front cover inner side of the front cover When opening the front cover support the both sides of the front cover with your hands avoiding suddenly falling down of the front cover Front cover Release button 2 Find a perforation at the left of the glass Use it to pull out the glass shown as in the graph below Pull up the Light Shield before pulling out the glass Note Before pulling out the glass make sure that the Light Shield has been pull up MII 900 Plus User s Manual 37 3 Use the cleaning cloth come with your package or a soft and nonabrasive lint free cloth to clean both sides of the glass 4 Next use a dust blower or a lint free cloth to clean components in the hollow part beneath where the glass is store
24. rts firmly and then insert them into the shipping carton 5 Close the top cover of the shipping carton and seal it with tape MII 900 Plus User s Manual 17 Taking a Closer Look Front Top Bottom View No Names of Parts Functions of Parts 1 Feed Tray Holes Uses to hook the Feed Tray onto the digitizer 2 Power Switch Turns the digitizer on or off 3 Fastenings of Light Shield Uses to fasten the Light Shield into Guide Arms on the Input Tray 4 Hook of Light Shield Uses to pull the Light Shield up 5 Front Cover Uses to cover inner components of the digitizer 6 Green Orange LEDs Indicates the status of the digitizer For more details refer to the Troubleshooting section of this manual 7 Output Tray Holes Uses to hook either the Output Guide or the Output Basket onto the digitizer 8 Release Buttons Releases the front cover to open the lamp holder There are two Release buttons located on each side of the front cover Press the buttons down simultaneously to release the front cover 18 MII 900 Plus User s Manual Rear Side View No Names of Parts Functions of Parts 1 Hi Speed USB Port Connects the Hi Speed USB USB 2 0 cable to the computer 2 Power Connector Connects the digitizer to the power cord MII 900 Plus User s Manual 19 Assembling Your Film Digitizer Installing the Feed Tray Coming
25. the supplied film holders the MII 900 Plus also allows you to scan various sizes of industrial RT X ray films up to 14 x 52 Positioning Industrial RT X ray Film MII 900 Plus s Feed Tray can hold only one piece of X ray film at a time This section shows you how to position a single sheet of X ray film into the Feed Tray 1 Install the Feed Tray onto your digitizer before using it Refer to the front sections Installing the Feed Tray for the detail Feed Tray 2 Load and insert the film into the Feed Tray with the side to be scanned facing up and with the top of the film directing upwardly Push the film into the tray until the edge of it touches the bottom edge of the Feed Tray Make sure that the Light Shield has been pull up MII 900 Plus User s Manual 33 3 Align the film with the center of the Feed Tray by sliding the two Guide Arms toward the film if the width of the film is less than 14 inches Guide Arms Note There are several precautions and reminders about using the digitizer correctly Please refer to the section as below for the detail e The Feed Tray can handle X ray films of the following sizes Width 2 5 to 14 63 5 to 355 6 mm Length 2 5 to 52 63 5 to 1320 6 mm Sheet Feed Single sheet per time e Ifthe film are torn curled or wrinkled do not put them into the Feed Tray
26. tlet as a loose connection may cause arcing and result in fire e Ensure to hold the plug or connector to disconnect the cable otherwise if you pull the cable only it may damage the core wire and result in fire or electric shock N e Place and route the power supply cord such that it is not likely to be walked on or pinched by items placed upon or against them paying particular attention to the cord near the power plugs convenience receptacles and at the point where it exits from the outlet N e When the digitizer is left unattended and unused for long periods of time unplug it from the wall outlet Moving and Storing the Film Digitizer N e Always ensure that the digitizer is stored properly before shipping or moving it Quick stops excessive force and uneven surfaces may cause the product to overturn when moving N AN e Do not hit or drop the digitizer The digitizer may be damaged if it receives a strong jolt which may result in fire or electric shock if the digitizer is used without being repaired J e Do not place the digitizer on any slippery slanted or unstable surface The product may slide or fall causing serious injury to people as well as serious damage to the product MII 900 Plus User s Manual 5 N N e Do not use the digitizer near water Never spill liquid of any kinds on the product or it may result in electric shock or other hazards N e This digitizer should be situated away from heat s
27. to scan because they may cause film jams e Remove clips or staples before placing the film into the Feed Tray DO NOT use the digitizer to scan your X ray film with clips or staples because they may cause film jams or damage the digitizer 34 MII 900 Plus User s Manual Scanning Industrial RT X ray Films 1 Follow the procedures for Positioning Industrial RT X ray Film without Film Holders to load the industrial film into the digitizer s Feed Tray 2 Follow the procedures steps 2 through 8 for Scanning Industrial RT X ray Films to launch the ScanWizard Industry software to specify your scanning requirements and to start scanning Scan Frame tool EJ Microtek ScanWizard Industry Digitizer Overview Settings Job Type Res 300 v Scan Frame Image Size Wt Untitled Gray Scale ppi 0 0847mm 14 00 H 17 00 20 918 KB Scanner Yiew Confection Help 1 Settings window Scan frame enclosed by red dotted lines MICROTEK tire pres CTRL key to keep spect ratio selection Preview window MII 900 Plus User s Manual 35 Care and Cleaning To ensure optimal performance from the MII 900 Plus it is important to clean several critical parts of the digitizer on a regular basis Cleaning the Glass Surface on the Digitizer 1 Push down two Release buttons at both sides of the front cover of the digitizer and open the f
28. xncnceet sane dantiaeacals teed sra caga ci ens aj tenes 39 Maintenance 2 22 c2c02sc2cc20 eens cris cecexescceeteecebieeneseuiecueieced ecvedeesseresiiesisecies 39 Appendix 2 200 D222520052525200520suisisasdissssdasiasayaaasdosbsasdissasasisiaicastaa danos 40 Fixing Filta Jams seas s cxtchicc cuts conn acesa ditada aspas das Rida senna piada bg 40 Troubleshooting ss ciassaaiacana snsc esnio pesa began ao aean denna Eca a 41 SPECI CALIONS ooien anie A E A TEE A AN NE 42 8 MII 900 Plus User s Manual Knowing about Your Film Digitizer The MII 900 Plus is a sheet fed film digitizer which is specifically designed for the use of the RT X ray film scanning The MII 900XL can capture details in bright and dark areas of industrial RT X ray films and provide the professionals a convenient method to digitize the physical originals for the electric data storage saving maintenance time and storage space enormously Features of the MII 900 Plus The MII 900 Plus comes with several important features including the following e Premium Image Quality With a high resolution of 2400 dpi a dynamic range of 4 7 Dmax and the 16 bit grayscale the MII 900 Plus allows users to get better image details in just seconds e Energy saving LED light source Adopting LEDs as the light source when the digitizer is detected by the system there are no requirements for any warm up time before carrying out the scan which boots your productivity and
29. zer need a professional to perform the required service or maintenance Do not attend to fix or perform the maintenance by yourself or it may cause dangers to you or the digitizer MIlI 900 Plus User s Manual 39 Appendix Fixing Film Jams 1 Open the front cover by pressing the Release buttons on the both sides of the front cover 2 After opening the front cover let the jammed film fall into the output basket and then remove it from the output basket Note To remove the jammed film from the digitizer you have to open the front cover first Otherwise your film may be damaged if they are forcedly removed 40 MII 900 Plus User s Manual Troubleshooting The LEDs on the front right panel of the digitizer indicate the status of the digitizer C All Off Digitizer is off J C E Flashing Orange Starting up or L scanning a 4 Alli On Ready to scan Green LED Orange LED First make sure that you have followed steps as described in the Assembling Your Film Digitizer section of this document Then if your problem is listed here try the suggested solution 1 No light comes on when the digitizer is turned on Make sure your digitizer is connected to your computer and plugged into a power source 2 The Add Remove Hardware Wizard appears on your screen Click the Cancel button and close the ScanWizard Industry scanning software Disconnect the Hi Speed USB cable fro
Download Pdf Manuals
Related Search