FP-570T User Manual
Contents
1. 1 The three power terminals are AC100V L AC Input Terminal live line AC100V N AC Input Terminal neutral line FG Ground Terminal connected to the FP chassis FP 570T User s Manual 3 5 Connect the FP power cable as follows Installation and Wiring D Check to make sure the FP s power cord is disconnected Remove the plastic terminal cover Remove the screws from the 3 middle terminals align the power wire connectors and re insert the screws Check each wire to make sure it 1s securely connected r 3 MEMI Use no more than 0 5 0 6Nem of torque to tighten the screws 3 2 2 Precautions 100V FP 570 TC11 Power Supply Please pay special attention to the following points when connecting the power cable to the Power Terminal Block at the back of the 100V FP 570 TC11 unit Twisted Lines constant voltage transformer main FP a input out put unit Z FP unit Za Input Out put Power Input Out H put Power main circuit o Operation Unit main Fp power po wer a a 3 o T1 T2 power input output If the supplied voltage exceeds the FP unit s range connect a voltage transformer didia Chapter 2 Specifica tions for the allowable voltage range For between the line and ground select a power supply that 1s low in noise If there 1s an excess amount of noise connect a noise reducing transformer V Use Volt2. Maintenance FP 570T User s Manual Symbols 640 x 480 pixels Features viil A Adjusting the Touch Panel s Display 3 9 Afterimage iii Analog RGB features viii Analog RGB Interface 2 3 Analog RGB Interface Cable 1 1 Angled Face Installation 3 2 Arcing 3 2 ATPH EXE 4 3 B Boot up Initialization 4 2 Brightness conditions iii variations iii Bundled Software Communication Programs 5 1 Buzzer 4 1 Buzzer output 4 5 C Cable Diagrams 2 5 CALIB EXE 4 3 Calibration mode 5 8 Calibration program 4 3 5 1 Caution explanation i Cleaning the Display Maintenance 7 1 Cleaning the display iii Click sound 4 1 Color displacement 3 10 Command List 4 1 Common grounding 3 7 Connecting the FP to a PC 1 1 Contrast Volume 3 10 FP 570 T User s Manual Index D Damages responsibility iv Data Format 8 bit ASCII 4 4 Default Contrast Volume Setting 3 10 Dip switches 3 8 Disassembling the unit ii Display coordinates 5 3 Display mode vii Displayed color 11 Dot Clock 3 9 E Easy Installation Features viii Electrical shock 11 Wiring 3 5 Electrical Specifications 2 1 Environmental Specifications 2 1 Excessively dusty or dirty environments iii Exclusive grounding 3 7 F FA Factory Automation viii Fire Hazard ii Flammable gas environment ii Flat Panel FP Dimensions 2 8 Forced Reset 4 1 FP Installation Dimensions 2 9 FP Parts Names and functions 2 7 Functional Specifications 2 1 2 2 G General
3. Connect the appropriate voltage Is it using the correct mE Chapter 2 Specifica power voltage Turn OFF the power switch Fix the power cable connection Is the power supply cable connected properly EEG Chapter 3 Installa to the unit rng Check the 100V unit s backlight Has the 11V unit s CFL Change the backlight if it backlight CFL been set has burnt Gut Chapter up correctly 7 3 Changing the 100V Unit s Backlight There is a problem with the FP unit Please contact your local FP distributor FP 570T User s Manual Troubleshooting Is the computer operating Start the computer Is RGB cable connected correctly Diagrams Select the correct display mode Is display mode with Dip SW1 4 Chapter 3 3 Operation Mode night Setup and Display Positioning Adjust the screen display position Does the screen display Chapter 5 5 Operation correctly Mode Setup and Display Position ing NO There is a problem with the FP unit Please contact your local FP distributor FP 570T User s Manual 6 3 6 4 Troubleshooting 6 1 3 The Touch Panel Does Not Work When the touch panel does not react or its reaction is very slow after it is pressed follow the flowchart below to find the origin of the problem and the appropriate solu tion From a personal computer touch panel data communication can be performed by the CALIB EXE program Please execute CALIB EXE to
4. 77 5 Rear View FP 570T User s Manual 2 9 Specifications 2 6 2 Installation Brackets Unit mm Top View Rear View 27 FL o Front View Side View H x31 OT iE 4 6 2 6 3 FP Installation Dimensions Unit mm 302 40 5 8cc less than 4 R 2 2 10 FP 570T User s Manual 3 Operation Mode Setup and Display Positioning Installation Install the FP unit using the following steps M Before mounting the unit please make sure the gasket 1s attached Gasket Create an Opening Following the FP Installation dimensions create cut the FP opening required for installation The FP s rubber gasket installation brackets and screws are all required when installing the FP Chapter 2 6 3 FP Installation Dimensions plate panel FP Opening t is important that the plate panel surface is flat clean and without wma any jagged edges The Plate Panel thickness should be between 1 6mm and 10 0mm 1 6 10mm FP 570T User s Manual 3 1 3 2 emma MEMI Installation and Wiring e For easier maintenance and operation and improved ventilation be sure the FP unit is mounted at least 100 mm away from any adjacent structures or objects Lol L 1 1mm i 100mm 100mm 100mm L 100mm t froomm CT 1 TT The FP uses natural ventilation through its outer shell for cooling When installing the unit horizontally or sideways
5. 45 degiees verial Y 30 to 10 degiees horzontal K 60 to 60 degiees vertral Y 55 to 35 degiees Anabg RGB herce SD herce ouch iterace CFL Qndernomal temperatures and hum iiy Hespan 20 000 hours CFL amp Gndernomal temperatures and hum iiy espan 25 000 hours Vertical angle Y axis Horizontal angle X axis FP 570T User s Manual 2 3 2 4 Specifications Interface Specifications For both 100V and 24V Units 2 3 1 Analog RGB Interface mETIT Iiputsynalcharcterstu Inage sinal anabg RGB Synchrionous signal TTL Evel negatve tne orposiwve une Scannmg type non nterbse Admstm ent fanctons Fickeradustment 0 Eves Anabg RGB contastadmnstm ent Horzontaldsp by positioning 46 15 preb Vertctaldisp by postonng 9 7 preb Spay Md G A Giaohrs Mode 640 x 480 640 x 400 640 x 350 2517WMMHz 1 camo 11 VGA text mode the far right side s 80 pixels do not display Selection of display mode is done via switch SW 1 4 Pin Assignments and Signal Names for Analog RGB No 5 sina pen IT iC eroe bri perm H SYNC Horzontal synchionous signal anout VeSYNC Vertral synchionous signal anout pene Connector M ini Dsub 15 pin type Connector set screw Inch type 4 40 E 10 15 13 14 15 FP 570T User s Manual Specifications 2 3 2 Serial Interface Baud rate 9600 bps Data Ength 8 bis Serial Interface P arty none Diop bas Pin Assignments an
6. Specifications 2 1 GLOBAL WINDOW SETUP GLOBAL WINDOW 5 5 Graphic Panel Auxilary Input Output 2 7 GP 470 External Dimensions 2 8 Installation Brackets 2 9 Installation Dimensions 2 9 Names and Functions of parts 2 5 2 7 Power Input Terminal Block 2 7 Serial Interface 2 7 Ventilation 3 2 Ground wire Wiring 3 5 Grounding wire 3 7 Guidelines ii H Header Data Format 4 4 High voltage ii I I O cover Contrast Adjustment 3 10 Infinite wait Touch Panel Input 5 5 Insertion Slot 3 3 Inspection Items Maintenance 7 2 Installation 3 1 Installation brackets Dimensions 2 9 Packaging ix INT 59H Function List 5 5 Interface Specifications 2 3 Internal buffer 4 2 IP65F standard 2 1 L Liquid Crystal Display LCD iii M Main circuit Wiring 3 6 Main Menu 4 2 4 3 Metallic dust ii Mouse simulation driver 4 3 N Natural ventilation 111 3 2 No Screen Display Troubleshooting 6 2 Noise resistance Wiring 3 6 Non Digital cable 2 3 O OA Office Automation viii Operating Environment Oil Resistance 2 1 Operation Mode Setup 3 8 Optional Equipment 1 2 Overheating 3 2 P Packaging Contents ix PC Connectivity Notes vil Periodic Check Up Maintenance 7 2 Pin Assignments 2 3 Possible Device Problems 6 1 Power Cable Connection Wiring 3 5 Power Terminal Wiring 3 5 Power Terminal Block 3 5 Wiring 3 5 Power Terminals 3 2 Precautions Grounding 3 7 Precautions Input Output Signal Lines 3 7 Precautions Power Suppl
7. a set OS and Touch Panel Driver Combinations OS Touch F Program Feature nclded n Feature nchded n Feature nclded n W md amp 95 TIW N95 1 ELLISELIMENRS M the touch Tf piogrem D pos o CALBEXE o EXE B Touch Panel Coordinate Data 1 Resolution Both the X and Y coordinates have a resolution of 1024 The origin point 0 0 is located in the upper right corner of the screen 0 0 Screen display origin with resolution of 640 x 480 is normally at the upper left corner of the screen Therefore a software to convert the touch coordinates to display coordi 1023 1023 nates 1s needed I The following software is sold separately TT WIN A mouse simulation driver for Windows 3 1 sold by GUNZE LIMITED TT WINNT A mouse simulation driver for Windows NT sold by GUNZE LIMITED TT WINO95 A mouse simulation driver for Windows 95 sold by GUNZE LIMITED FP 570T User s Manual 4 3 Touch Panel Commands 2 Data Format All data is in 8 bit ASCII format and is structured in the following 11 byte strings Header 1 byte T touched R released X coordinate 4 bytes 0000 1023 Separator I byte Y coordinate 4 bytes 0000 1023 Termination code byte CR ODh pt tt tT yet llle M X coordinate Y coordinate 31h 0 39h 9 31h 0 39h 9 four digits four digits 54h T Touched 2Ch fixed ODh n fixed 52h R Released lt Ex
8. cU Mae DM PORE I2 Optional Equipe Mb esie aoo rao abe aae votes tutats paca ond a vence pit cams aed eueus tute debuts Chapter 2 Specifications 22 General S PECUICAMIONS I OO o Sm l ISCHIA SPE CINI CAL OMG aucem diede erm oO eoo dia d ete ip doo dle dide eeadreiaee 2 Environmental Specifications oet Eoesect o E INE ELE eR ees 3 t ctutal 3S PEC IE CANONS oio eet ir dede ente reser bedient a S dsba Lo een ue iras edita 2 2 Functional Specificato nS ceusuotodecctudus E E Eu Du eR dudo dd 2 9 Int traceSpecIbe aUIODIS a c on eucuuo Subcaute edes oe b beer Rab EQuuuo fusca e dose h eost sputo sur oe T Analog ROB Ter aC ceense eate etae deed based efie decas a iu agio zoe Qui ue PS Sab DNE ETT T mm 2 4 Cable DIaetamsc oid aa a a uim ar TUTO UE 1 Pin Connections for the RGB Interface Cable eeeeseeeeeeenn 2 Pin Connections for the SIO Interface Cable sees 2 5 Names and Functions of FP Parts eeeeeeeee ee eren nennen rnnt nus 226 Flat Panel CEP DImelistOls oett tte Sr tee mee rH rtv denvvtetetutatetatabvsv tom a de iueassd L FP570 T External Dimensions 5 uocoareteser e oco ted oi o evo solere amt oie wevwcdauseotcodeais 2 Installation Brackets 252 rez eese ree vetu etes ates Pa ee eed esee tee id vsu pe i oed ove oic od be 9 EP Installation Ditiensiolls 2 0 2 2 coxiOe aa oda ouis eu paL d Chapter 3 Installation and Wiring S MEE SCIL tese ccm
9. check touch panel s operations Fada ea 3 2 CALIB EXE Touch Panel Data Calibration NER MEMI Touch panel not working NO Connect the SIO cable correctly 2 4 Cable Diagrams Is the SIO cable connected correctly There is a problem with the FP unit Please contact your local FP distributor FP 570T User s Manual a L E 1 Cl af 2 Peri die ofi a s Backlight 3 Changing EM Cleaning 7 1 1 Cleaning the Display When the display or the border around the display become dirty soak a soft cloth in a neutral detergent wring it well and wipe the display 4 4 Donotuse paint thinner organic solvents or highly acidic compounds mir e to clean the unit Do not press the touch screen with hard or pointed objects such as a mechanical pencil since they may damage the surface of the screen FP 570T User s Manual 7 1 7 2 Maintenance Periodic Check Up To maintain your unit in its best condition please check your unit periodically Inspection Items Surrounding Environment O Is the surrounding temperature within the allowable range O Is the humidity within the specified range 30 8590 RH O Is the atmosphere free of corrosive gas FP Temperature When the FP unit is mounted into a cabinet the conditions inside the cabinet are considered to be the environment Electrical Specifications O Is the input voltage appropriate AC 100V o
10. mode If the test result is OK press the Enter key After the following message appears enter the name of the data file and press the Enter key Em When the data filename is speci fied from the parameter C path during the execution of CALIB EXE the program will terminate without showing the message on the left FP 570T User s Manual 6 1 Troubleshooting 6 1 1 Possible Device Problems Possible types of trouble while using this unit are as follows No display No display appears after the unit is switched on The screen disappears during running mode The screen does not display normally Touch panel doesn t function The touch panel does not react when pressed or its reaction time is abnormally long A Warning Because of the danger of electric shocks be sure the power cable is not connected when wiring the unit When changing the backlight there is a danger of electric shocks or burns so be sure to turn the unit OFF and wear gloves This section assumes that the FP is the cause of a problem not the camion host PLC When the host is the problem please refer to its corresponding manual FP 570T User s Manual 6 1 6 2 Troubleshooting 6 1 2 No Display When the screen does not display when powering up or if the screen turns OFF by itself use the flowchart below to find an appropriate solution No Screen Display Does the backlight CFL light up NO
11. portrait style use a fan or air conditioning unit to prevent overheating SUE ic LC c CC E 7 Vertical Installation Side Front Horizontal Installation Dp ee R N i uM p UR E UU PI IE AE BENE UE HSIEIES I SIS MIS S ed 7 Sideways Installation Poe J When installing the FP sideways place it so that the Power Terminals point upwards Check that heat from surrounding equipment will not cause the FP to overheat Do not use the 100V FP 570 TC11 in an environment that exceeds 40 C and the 24V FP 570 TC21 24V in an environment that exceeds 45 C Ensure this unit is located as far away as possible from electromagnetic circuits non fuse type breakers and other equipment that can cause arcing When installing the FP unit in a panel with an angled face the face should not incline either backwards or forwards more than 30 H Ir E A LG less than 30 L 1 I say S ga Y FP 570T User s Manual Installation and Wiring Install the FP unit into the front of the panel Panel Side View Install the brackets from the rear of the panel There are a total of 4 insertion slots 2 on the top and 2 on the bottom of the FP for the metal installation brackets to hook onto Top Bottom View 2 Installation Bracket b 7m Panel Front Side Back Side Insertion Slot After inserting each bracket into its app
12. the FP 570 T Vill The features of the FP 570 T are as follows High Quality TFT Color LCD Display This unit 1s equipped with a 10 4 inch TFT type color LCD Its superior brightness and wide viewing angle not found in ordinary laptop type TFT LCDs widens your scope of applications The screen s maximum resolution is 640 x 480 pixels and can display 260 000 colors Easy Installation In User s Cabinets and Panels The FP 570 T s slim lightweight and compact design make installation a snap It was designed specifically for use as your FA Factory Automation or OA Office Automation system monitor The flat front panel meets the rigorous IP65F standard and even without any protective cover the flat panel is highly resistant to both water and dust Flat Panel can be used as a VGA Display Since the FP 570 T is equipped with an analog RGB interface it can be connected to any PC with standard VGA mode The PC s clock frequency however must be within the standard range Easy Operation With the Built In Touch Panel The FP 570 T s built in touch panel is standard equipment allowing touch panel data to be output to a host PC via input output commands and an RS 232C cable Ultra convenient for systems requiring both touch panel operation and monitoring FP 570 T User s Manual Package Contents The FP s packing box contains the items listed below Please check to be sure each is included and is not
13. the display position to the left FP 570T User s Manual 3 9 3 10 Installation and Wiring 3 3 3 Default Contrast Volume Setting and Adjustment The default contrast setting for the FP unit 1s based on the standard IBM PC series display If you connect the FP unit to another type of PC unit with a different RGB screen output level then color displacement or screen flicker may occur In such case please adjust the display as follows Unscrew the FP s two I O cover screws and remove the cover I O Cover Turn the Contrast Volume in clock wise to make the screen brighter and counter clockwise to make it darker o OO00 000 o Contrast Volume caution When readjusting the contrast please use a ceramic or plastic screwdriver to avoid causing an electric short or damage from static electricity FP 570T User s Manual Chapter 4 5 houcw interface Data 2 Boot u MZAA A hA Panel Commands ESI Command List Here the touch panel commands host gt touch panel supported by the FP 570T are described The comma used between the transferred format sent by the touch panel to the host computer is only for separating commands and has nothing to do with the actual touch panel commands Command codes and data are all expressed in hexadecimal format Example 65h 65 HEX lt Touch Panel Commands gt Regardless of the dip switch set
14. 2 25 WN MIN etna E cu Maa Nescit NA EE PTE N LCS dne taU e S aot eens Power Cable Connec UD tetona cdit ioi Eod pieni eeu cuo iato rfe tubi tu bae ea uie 2 Precautions 100V FP 570 TC11 Power Supply eeeeeeMee BS PRC CAUTIOUS c Ground MED eoo vs Go ert om be NO deo suede Pe Delos e ence debi lad b Ra buses uo ERG 4 Precautions Input Output Signal Lines esses FP 570 T User s Manual vl 3 3 Operation Mode Setup and Display Positioning i ceecesseeeeeeeeeeeeceeeeaeeeeeeeeees 3 8 1 Operation Mode Setup and Adjustment ccccccccccccceeeceesesseeeeeeceeeeeeeeeeeeaas 3 8 2 Adjusting the Touch Panel Display sneren e EE aaa 3 9 3 Default Contrast Volume Setting and Adjustment cc cccceseseeeseeeeeeceeeeeeeeeeeeeeeeeaas 3 10 Chapter 4 Touch Panel Commands AE C Oia MOIS NER UU E UM 4 4 2 jBoot up InttaltzatlOD oio eto ioco do e a ea lotto ous 4 2 d onchdnteridee D abdo tole E ett tiov dieu retota sebo v Dieu ene d ated Dou PU 4 3 4 1 Touch Panel Commands eee Eee ois epe ea ine pauco eaae to tespaso Qeepe nde E 4 5 Chapter 5 Touch Panel Communication Programs pL Budsdied SO tWabe 59e hodie fete ae ene oat d IRE 5 592 Operauon BnyIEoDitielit wa osos ceu aieo esed atrae a atuo db cunas deb to tts 5 2 259 Touch panel npor DIVE Susa ate E ipu n mild eM ON ETeM mco icum hes 5 3 ATPH EXE Touch Panel Handler one ntesite ebd Fes A Ha co pha dee 5 3 2
15. 720 x 400 or 720 x 350 Dot clock frequency 28 322MHz 1 VGA special graphics mode 640 x 400 Dot clock frequency 25 175MHz 1 SWI1 5 This switch controls the Automatic Backlight OFF mode When this switch is ON and if there 1s no SIO transmission or touch operation performed for 5 minutes the backlight turns off automatically It will remain OFF until another SIO transmission or touch operation takes place at which time the backlight automatically turns back on If the FP unit is frequently not used please set this switch ON to extend the life of the backlight Also if a display related command is transmitted by the SIO this Automatic Backlight OFF mode will be automatically disabled SWI1 6 This controls 1s used as the touch screen Click sound s ON OFF switch When this is set to ON a click will sound every time the touch panel 1s touched 3 3 2 Adjusting the Touch Panel s Display Turning ON the FP unit while the upper left corner of the touch panel is pressed will cause the FP to enter display positioning mode In this mode by touching certain areas you can adjust the display s positioning and its dot clock Touch here while turning the power switch ON um oS The above touch area data will not display on the screen DOT CLOCK for screen flicker adjustment Display moves the display position upwards Positions moves the display position downwards moves the display position to the right moves
16. CALIB EXE Touch Panel Data Calibration eeeeeeeeen nnn 5 7 Chapter 6 Troubleshooting Gl ErOublesNOOUNe etc nite ciriscee 6 1 possible Device Problems iis ooo haces c eed wa tee Sanita tite a e ene Saat poa ur coe 6 1 Z INOS LAY so ERU m Bodice teadendaeeeeanece tues 6 2 3 TOUCH Panel Docs NOC W ORK derina a a a a NG s opis s Mss UU 6 4 Chapter 7 Maintenance and Inspection T Resare in Mer ETT 7 1 b Sle amie The Dis Plan de 7 1 72 JRemodic Check in dide teni Pap ot eco eee Edu occ t ein ats 7 2 7 3 Changing the 100V Unit s Backlight eeeeeeeeee 7 3 FP 570 T User s Manual PC Connectivity Notes The FP unit s analog interface is designed for standard VGA mode The number of dots pixels displayed are as follows Display Mods Bot Clock Rangs Text Mode 720x400 120 x 350 28 322MHz 1 E Graphics Mode 640 x 480 640 x 400 640 x 350 25 175MHz 1 CAUTION When the unit is used in VGA text mode the far right side s 80 dots are not displayed The display mode is designated using dip switch SW1 4 Some types of VGA equipment may not be within the ranges specified above and therefore cannot be connected to the unit Also if the user changes his PC s VGA board there is the possiblity that the new board may not be able to be connected to the FP FP 570 T User s Manual vii Features of
17. For the Safe And Correct Use of this Unit This manual describes safety instructions for correct use of the FP unit Please keep this manual close at hand and refer to it when necessary The following symbols are used throughout this manual to ensure the safe use of the FP unit Please make sure to follow all instructions given since they explain impor tant safety points This mark warns of a situation that could either seriously injure a person or lead to death if the instruction 1s ignored and or the unit is used incorrectly This mark warns of a situation that could either injure a person or damage property if the instruction 1s ignored and or the unit is used incorrectly Other Symbols Used In This Manual The list below describes the symbols used in this manual Explains a situation that requires a moderate amount of caution Indicates a word or phrase that has an additional explanation A reference point Describes the word or phrase marked by the as terisk and the corresponding number Reference pages on related topics Operational steps Please follow these numbered steps in order to perform the desired operation FP 570 T User s Manual 1 Warning safety Instructions For the safe use of this unit please follow these guidelines B Because of the ever present danger of electrical shock be sure to unplug the power cable from the FP unit before plugging the cable s other end into
18. UND BLU NC GROUND MONITOR SENSE COLOR MONITOR SENSE COLOR OUTPUT HSYN OUTPUT VSYN NC OUTPUT OUTPUT OUTPUT c ON Oa Ro N gt na O N Signal names for the FP s RGB interface are designed to match the same pin order as the RGB interface on personal computers FP 570T User s Manual Specifications Pin Connections for the SIO Interface Cable FP side SIO cable PC side 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 O COnN OU BWYN BE Signal names for the FP s SIO interface are designed to match the same pin order as the SIO interface on personal computers FP 570T User s Manual 2 7 Specifications Names and Functions of FP Parts Front View A TFT Color LCD The display monitor for your host PLC B Touch Panel Allows you to perform touch operation C Power Lamp Indicates if the PL isturned ON C Power Input Terminal Block Provides the input and ground terminals AB for a power cable D Setting Switches Dip switches Rear View E VGA Interface analog RGB E Connector CA F Serial Interface Used for both sending touch panel data to the host and receiving commands from the host FP 570T User s M anual Specifications Flat Panel FP Dimensions 2 6 1 External Dimensions Both 100V and 24V units Unit mm Top View 301 Side View 85 Front View 317 7 5
19. age and Noise Reduc ing transformers that have ca pacities that exceed 100VA When supplying power to the FP unit please separate the input out put and operation unit lines as shown in the figure To increase the noise quality sim ply twist the power cable before connecting it to the FP unit The power supply cable must not be bundled or kept close to main circuit lines high voltage high cur rent or input output signal lines Connect a surge absorber as shown in the diagram to deal with power surges To avoid excess noise make the power cable as short as possible FP 570T User s Manual Installation and Wiring r surge eme m absorber 3 2 3 Precautions Grounding a Exclusive grounding BEST FP unit other equipment b Common grounding OK FPunit other equipment c Common grounding BAD FPunit other equipment am e Make sure the surge absorber El is grounded separately from the FP unit E2 e Select a surge absorber that has a maximum circuit voltage greater than that of the peak voltage of the power supply Connect the FP s FG terminal to an exclusive ground diagram a Grounding resistance of under 100 If exclusive grounding 1s not possible use a common connection point dia gram b The grounding wire should have a cross sectional area greater than 2mm Make the connection point as close to the FP unit as possible and make the
20. ample gt If the coordinate X 23 Y 500 is touched T0023 0500CR touched T0023 0500CR continuous output with the same location T0024 0500CR moving the location without releasing touch T0024 0499CR continuous data output unless finger 1s released T0022 0501 CR T0023 0500CR R0023 0500CR when released only 1 unit of data is sent 3 Sampling Rate A maximum of 87 points per second 4 4 FP 570T User s Manual Touch Panel Commands 44 Touch Panel Commands The following are touch panel commands sent from the host computer to the FP unit nema The letter inside the bracket next to the command code shows the actual character used for that code Display ON 65h e Turns on FP 570T s display Backlight is also turned on simultaneously Display OFF 66h f Turns off FP 570T s display Backlight is also turned off simultaneously Backlight ON 67h g Turns on FP 570T s backlight Display is also turned on simultaneously ssh cm Turns off FP 570T s backlight Display is also turned off simultaneously Regarding the Automatic Backlight OFF mode and display commands When the FP unit is in Automatic Backlight OFF mode Dip SW1 5 ON and ifa display related command is transmitted to the unit the Automatic Backlight OFF mode will be cancelled CAUTION Automatic Backlight OFF mode is only initialized at boot up Click sound high ON 69h i Makes a high click sound when the touch
21. ay resident After execution the command stays in memory caution When the data file made by CALIB EXE is not found or cannot be 2 opened the following message appears In such a case the program will run without data correction e If data correction is not carried out successfully the display position may not match with the touch panel input position 5 4 FP 570T User s Manual Touch Panel Communication Program B Function ATPH EXE has the following functions which are activated by software interrupt Default INT59H function calls INT 59H Function List gt 0200n Iiputbufercbar 8500h Detection oftouch panel s condition FEOOh ResuentConfim aton B Function Explanation Function 8100h Touch panel input infinite wait Returns touch coordinates Waits infinitely for input input AX 8100h lt output gt AH 0 normal termination BX Y coordinate 0 479 DX X coordinate 0 639 CX Number of effective input buffer for the analog touch panel Function 8101h Touch panel input instant return Returns touch coordinates It will quit the function 1f there is no input input AX 8101h lt output gt AH 0 input no input BX Y coordinate 0 479 DX X coordinate 0 639 CX Number of effective input buffer for the analog touch panel Function 8102h Non renewing touch panel input Sends the position coordinates and does not renew the panel s in
22. d Signal Names for Serial nterface d Signal Cond ton P in Location Name lt ae CamerDetect FP gt Host D2 ao sexo fies Orne Le ere sent eem Le rooms Connector Dsub 9 pin female Connector set screw Inch type 4 40 Concerning Signal Names 4 Signal names used for the serial interface on FP units are designed to match the pin order used on most PC serial interfaces so that a straight cable can be used to connect the two Therefore connect each pin s signal to the same signal name on the PC side For an example pin 2 RD should be connected to the RD input terminal on the PC s connector Refer to section 2 4 Cable Diagrams for each signal s direction FP 570T User s Manual 2 5 RGB Interface Cable Pin Connections FP side ANALOG R ANALOG G ANALOG B RESERVED DIGITAL GROUND RETURN R RETURN G RETURN B RESERVED DIGITAL GROUND RESERVED RESERVED H SYNC V SYNC RESERVED c ON OO FW DY gt O N RGB cable RED IN GRN IN BLU IN NC GND RED GND GRN GND BLU GND NC GND NC NC RED VIDEO GRN VIDEO BLU VIDEO NC GROUND GROUND RED GROUND GRN GROUND BLU NC GROUND MONITOR SENSE COLOR MONITOR SENSE COLOR HSYN VSYN Oo ON Oo 0 FPF WN gt fo eel O N Specifications PC side RED VIDEO GRN VIDEO BLU VIDEO NC GROUND GROUND RED GROUND GRN GRO
23. d actual coor dinates Then from the result a correction data file to be used by ATPH touch panel handler is made B How to Operate CALIB d parameter Explanation of parameters d Attach this parameter all the time a lt n gt Selects the I O base address of the SIO port where the touch panel is connected hexadecimal default 2f 8 n 3f8 COMI 2f 8 COM2 q n Selects the interrupt level IRQ for the SIO port where the touch panel is connected default 3 n 4 COMI 3 COM2 c path Specifies the data file made by CALIB EXE touch panel data calibration that contains the correction value memo When the touch panel is connected to COMO the default value can be used gm Operation Procedure D When CALIB EXE is ex Analog Touch Panel Calibration CALIB EXE Version 1 01 ecuted the message on Copyright e 1994 Digital Electronics Corporation the left displays on the Calibration Mode screen Then the two designated position upper left and lower right corners starts to blink Touch upper left and lower right corner of the screen Enter Go to test mode Esc Terminate program Upper left Lower right O00 0000 QUDU Q000 FP 570T User s Manual 5 7 Touch Panel Communication Program Analog Touch Panel Calibration DBLIB EXE Version 1 01 Copyright c 1994 Digital Electronics Corporation Calibration Hode Touch upper left and lower right corner of the screen Ente
24. damaged L1 FP unit FP 570 TC11 or O FP 570 T User s Manual FP 570 TC21 24V n LERNEN FP 570 T User s Manual 100V 24V Units L1 3 5 inch floppy disk O Installation brackets 4 Contains Touch Panel programs k 7m These items have all been carefully packed with special attention to product quality However should you find anything damaged or missing please contact your local distributor immediately for prompt service FP 570 T User s Manual 1X FP 570 T User s Manual 1 C CLMACI ENG FP LO ARK The following diagram illustrates the connection between the FP unit and a PC Connecting the FP to a PC Wiring CX mq FP 570T unit Analog RGB Interface Cable VGA standard Dsub 15 pin male FP 570T User s Manual 1 1 SIO Interface Cable Dsub 9 pin female Personal Computer PC Introduction E Optional Equipment All optional equipment listed below are products of Digital Electronics Corp Model eeeenipuon Backight Rephcem entBackightbubs GP570BLOOMS Mainte nance fhsta JAton M etalinsta JAton brackets for GPO7OATOOMS Parts Brackets FP 570 I Rephcem ent rmribbergasket R hen 1 Im KP ubber GP570 4 POO MS used when msta Bue Gasket Same as the FP 5 orgmal gasket P rovides disposabb screen pirotecton fom dustand other GPS70D F104 ebm ents The touch panelcan be used with the C overS heet attached 6
25. er 5 4 Vertical Installation 3 2 VGA board vii VGA text mode Right side 80 pixels 2 3 Viewing angle Definition 2 2 Voltage Transformer 3 6 FP 570 T User s Manual iii
26. o the unit for long periods of time If the GP s front face protection sheet becomes peeled off these conditions can lead to the ingress of oil into the GP and separate protection measures are suggested Also if non approved oils are present it may cause deforma tion or corrosion of the front panel s plastic cover Therefore prior to installing the GP be sure to confirm the type of conditions that will be present in the GP s operating environment If the installation gasket is used for a long period of time or if the unit and its gasket are removed from the panel the original level of the protection cannot be guaranteed To maintain the original protection level you need to replace the installation gasket regularly 2 1 3 Structural Specifications C eese Sooty Syer FP 570T User s Manual Specifications Functional Specifications For both 100 V and 24V Units C omes T oem Cont astAd usm ent Volme adusim entavaiBb b dmstm entdali bcated n rearofFP Touch Panel Resoixon 1024 x 1024 Method Anabg Resistance Fim Disp by Ara nm 211W x 158H Disp By M ode Ge ected with a swich Vewng Angb Back toht 1 C gt 1 Definition of Viewing angle VGA textm ode 720x400 720x350 Farrohtsde s 80 dot are notdisphbyed 400 or 350 Ine disp by modes ae disp Hyed m the center VGA graphics m ode 640x480 640x400 640x350 400 or350 Ine disp by modes are disp Hyed m the center horrorntal Kk 45 io
27. or organic solvent Do not press on the touch panel s face with sharp objects such as a mechanical pencil or screwdriver since it might damage the panel Avoid using or storing the FP in direct sunlight excessively dusty or dirty environments or where chemicals or their vapors are present in the air Avoid restricting the FP s natural ventilation or storing and using the FP in an environment that will increase the FP s internal temperature Please avoid using the FP in areas where sudden large changes in temperature may occur These changes can cause condensation to form inside the unit possibly causing an accident Notes on the FP s Liquid Crystal Display LCD The FP s LCD contains a strong irritant If the panel is ever cracked and the LCD s liquid contacts your skin be sure to wash it with running water for at least 15 minutes If any of this liquid should enter your eye be sure to flush the eye with running water for more than 15 minutes and see a doctor immediately The current brightness of the LCD screen will depend on the screen s current display and the LCD s contrast adjustment Any brightness variations that result are normal for LCD displays There are minute grid points on the LCD surface These points are not defects Sometimes crosstalk shadows appearing on extended display lines will appear on the display This phenomenon is a common attribute of LCDs and is not a defect The displayed color will look diffe
28. out the express permission of the Digital Electronics Corporation of Japan 2 The information provided in this manual 1s subject to change without notice 3 This manual has been written with care and attention to detail however should you find any errors or omissions please contact Digital Electronics and inform them of your findings 4 Please be aware that Digital Electronics 1s not responsible for any damages resulting from the use of our products regardless of article 3 above Specifications set out in this manual are for overseas products only and as a result some differences may exist between the specfications given here and the Japanese ones 5 All Company Manufacturer names used in this manual are the registered trademarks of their respective companies Copyright March 1997 Digital Electronics Corporation FP 570 T User s Manual Table of Contents For the Sate and Correct Use ofthis Unit sisi atu bs gone e b on uude uomo suceso Oui o euet Warmin Safety InSttollODs ones drei rond ea ee pates dod iuc a UAR MR TRUE 1 Caution Safety Tnt LOTES ississsnrencdsaatisensbacconsbsnscdaieandaaneneend Abba N 111 Pre ICC nee eine a n E eee ee re l Table OI One D eusa a a aa x diaeta abun PC C ONTEN IDON OlCS Ea a E tS cU dito posu iota RE adr eed Features orthe PPS ico ER l Paekauc C OMG MIS easa a a a edie Chapter 1 Introduction IF Connecting the PP fo PG aussen vede ves bugs stt ote s a pespu Mani enu Usa
29. panel is touched Click sound high OF 6Ah j The high click sound will not activate Click sound low ON 6Bh k Makes a low click sound when the touch panel is touched Click sound low OFF 6Ch 1 The low click sound will not activate Buzzer high ON 71h q Turns on the buzzer output high Buzzer high OFF 72h r Turns off the buzzer output high Buzzer low ON 67h s Turns on the buzzer output low Buzzer low OFF 68h t Turns off the buzzer output low FP 570T User s Manual 4 5 Touch Panel Commands The order of priority for the buzzer and click sounds 1s as follows They are not processed simultaneously Command Code Priority Order Buzzer high ON 71h high Buzzer low ON 73h Click sound high ON Click sound low ON Also if the OFF command for each buzzer item 1s transferred regardless of the priority order only that buzzer item is turned off Example If the following three commands are sent at the same time Buzzer high ON Buzzer low ON Click sound high ON the Buzzer high activates However when the Buzzer high OFF command is sent afterwards the Buzzer low will activate Reserved The following commands are reserved If these commands are used they are sometimes treated as errors 30 2 2 3 Reserved 20h 22h 23h 25h 26h 27h 28h 29h Ah Bh 33h Ch 42h 43h 44h 45h 46h 47h FP 570T User s Man
30. put buffer input AX 8102h lt output gt AH 0 input no input BX Y coordinate 0 479 DX X coordinate 0 639 CX Number of effective touch panel input buffers Nn FP 570T User s Manual 5 Touch Panel Communication Program Function 0200h Input buffer clear Clears the touch panel s input buffer input AX 0200h lt output gt AH 0 normal end Function 8500h Detection of touch panel s conditions Returns the touch panel condition input AX 8500h lt output gt AH status at 640 x 480 mode o9 p ow 0 1 nochange e ee Function FEOOh Confirmation of resident memory If ATPH EXE is resident in memory a fixed message and its version number are returned input AX FEO00h lt output gt AH Q normal termination BL Y BH B CX version number Fit 15 0 Version number ATPH EXE discrimination number Carry clear 5 6 FP 570T User s Manual Touch Panel Communication Program 5 3 2 CALIB EXE Touch Panel Data Calibration Because of changes in operational environment and the unit s deterioration dif ferences in theoretical and actual touch coordinates arise and therefore these differences must be corrected periodically via a utility software called CALIB EXE touch panel data calibration By touching the designated position on the display upper left and lower right CALIB EXE calculates the difference between the theoretical an
31. r Go to test mode Esc Terminate program Upper left Lower right CUS te eb TOSS OO The actual value is shown on the display Terminate program without saving calibration data Y N Analog Touch Panel Calibration DRLIB ERE Version 1 01 Copyright c 1994 Digital Electronics Corporation Test Mode Enter save calibration data and Exit Esc Return to calibration node Calibration data name APPR GRE Enter the file name 5 8 Touch the desigated positions one after the other CAUT ICH Y Do not touch two points at the same time Touch right above the designated position By re touching the points the ac tual coordinates will redisplay Correction data will be calculated from the difference between the actual and the theoretical values JR Press the Esc key to terminate m the program Press the Y key after the message on the left 1s shown and the program will terminate without saving any calibration data If the N key is pressed the system will return to calibration mode To enter test mode press the Enter key This mode tests whether the calibration has been processed correctly or not The calibration 1s confirmed as suc cessful if the locus shown on the display matches as touched Otherwise return to the calibration mode and redo the calibration by touching the right blinking position dart m ress the Esc key to return to calibration
32. r DC 24V Attachments O Is the cable connected properly Is it loose O Are the mounting brackets holding the unit securely O Are there many scratches cuts or traces of dirt on the rubber gasket FP 570T User s Manual Maintenance Changing the 100V FP570 TC11 Unit s Backlight A Warning Whenever changing the Backlight be sure the power has been turned OFF When the unit is Hot be sure to use gloves to prevent injury e When the unit is still ON high voltage runs through the Backlight area do not touch When the power has just been turned OFF both the unit and Backlight are still very hot The 24V FP571 TC21 24V unit s backlight should only be changed by an authorized Digital serviceman Do not attempt to change this backlight by yourself Change the Backlight following the instructions shown below Be sure to wear gloves D Unplug the FP s power cord With a screwdriver unscrew the two screws on the upper rear face of the unit Open only the upper part of FP and remove the backlight s connector Take the old backlight out Insert a new Backlight and reconnect the power connector 00 0 9 Put the panel cover back in place and reattach its screws In this step be careful not to pinch any of the connector s wiring between the Backlight cover and the FP s body two screws connector FP 570T User s Manual 7 3 7 4
33. rent when viewed from an angle outside the speci fied view angle This 1s also normal Displaying a single screen image for long periods of time can cause an afterimage to remain To correct this turn the unit OFF for 5 or 10 minutes then ON again This phenomenon is a common attribute of the LCDs and not a defect To prevent this effect you can use the Display OFF feature if the same image is to be displayed for a long period of time change the screen display periodically to prevent the displaying of a single image for a long period of time FP 570 T User s Manual lii Preface ee 1V Thank you for purchasing Digital s TFT type color display panel the FP 570 T hereafter referred to as the FP unit The FP unit is a TFT type color liquid crystal display monitor for IBM PC compatible per sonal computers VGA mode Please read this manual completely to insure the correct use and complete understanding of the FP unit s functions The FP s analog interface is designed for use with standard VGA mode Please be aware that this unit may not be able to be connected with nonstandard VGA modes For more details please refer to this manual s PC Connectivity Notes section The term FP 570 T refers to the following units FP 570 TC 11 AC 100V type FR 570 TC21 24V DC 24V type with CE marking Note 1 It is forbidden to copy the contents of this manual in whole or in part except for the user s personal use with
34. ropriate slot carefully force it to the back of the FP Ek ET FP 570T User s Manual 3 3 3 4 Installation and Wiring Use a screwdriver to tighten the screw and secure the FP unit in place A torque of no more than 0 5 0 6 Nem should be required to tighten the screw FP ae Using too much force may break the case and damage the unit FP 570T User s Manual Installation and Wiring 3 2 1 Power Cable Connection Warning To prevent electrical shocks be sure the Power Cable is plugged first into the FP unit then into the wall main supply e Your FP 570 uses input voltage of either DC24V or ACIOO0V If your power supply is greater than that required by your unit it may damage both the power source and the FP unit n lieu of the power switch on the FP unit please connect a breaker unit cuo When connecting the FG terminal be sure to connect the ground wire Not grounding the FP unit will create excessive noise and vibration e Wherever possible use thick wires max 2mm for power terminals and provide an extra twist to the wire before connecting it e The ring terminal size should be as follows Qj3 2 mm less than 6 0 mm e Toavoid a power short when loosening power terminal screws use a power terminal with plastic sleeves 100V Unit FP 570 TC11 Power Terminal Block Crimp on Ring Terminals 24V Unit FP 570 TC21 Power Terminal Block Crimp on Ring Terminals
35. sheets set 1 2 FP 570T User s Manual 1 General eC atio 2 Functional YUU 3 Interface Specifications ble Diagrams Names and Functions of FP Parts 6 Flat Panel FP Dimensions General Specifications For both 100V and 24V Units 2 1 1 Electrical Specifications sd 100V FP 5 0 TC1 24V EP 5703C1224V ACSS 13N SOD Ez DCZ 208 awarna O O wRhms Voltage Endurance AC1500V 20mA 1m mute AC1000V 10mA lmmute between the lve wie and between the lve wie and giound ng tem nak grounding tem nak Bo Bton Ressiance DC500V above 10MOhm between the Ive wie and gioundng tem nab 2 1 2 Environment Specifications o T me e E Siehii sti Nose Endurance Nose volage 1200 Vp p Nose voltage 1000 Vp p Puke Ength 1m xwsecond Arse tme sel 1 nanosecond G ound Connecton Less than 100 2 oryourcounty 5 applcabb standard Ratng Equyvabntio P65f UEM 1030 and NEMA 250 TYPEZX 12 See the next page s note FP 570T User s Manual 2 1 Specifications 1 Continued from previous page The front face of the GP unit installed in a solid panel has been tested using condi tions equivalent to the standard shown in the specification Even though the GP unit s level of resistance is equivalent to the standard oils that should have no effect on the GP can possibly harm the unit This can occur in areas where either vaporized oils are present or where low viscosity cutting oils are allowed to adhere t
36. splay panel so that it can pass the absolute input coordinates to the application software The following picture shows the relation between the touch panel and the display panel coordinates Touch panel coordinates Hg Display p di 0 0 coordinates 0 0 Touch panel coordinates 1023 1023 Display coordinates 640 480 The touch panel coordinates are converted to the display coordinates when ATPH EXE is activated FP 570T User s Manual 5 3 Touch Panel Communication Program Mi How to Operate the Software ATPH d parameter or ATPH r Explanation of parameters d Attach this parameter all the time a lt n gt Selects the I O base address of the SIO port where the touch panel is connected hexadecimal default 2f 8 n 3f8 COMI 2f 8 COM2 q n Selects the interrupt level IRQ for the SIO port where the touch panel is connected default 3 n 4 COMI 3 COM2 i lt n gt Sets the vector number for the function call s software interrupt hexadecimal default 59 r Removes the current resident memory command c path Specifies the data file made by CALIB EXE touch panel data calibration that contains the correction value ATPH CAL in the current directory is selected for default When this program runs the following message will display on the screen Analog Touch Panel Handler ATPH EXE Version 1 00 Copyright c 1993 Digital Electronics Corporation St
37. the wall B Do not use power in excess of the unit s specified voltage range since it may cause a fire or electric shock B Because the FP unit is contains high voltage parts an electric shock can occur when disassembling the unit Therefore please be sure to always unplug the unit before disassembling it Do not modify the FP unit in any way since it may cause a fire or electric shock When changing the backlight be sure to turn off the unit s power first in order to prevent an electric shock Do not use touch panel keys to perform life threatening or vitally important safety functions Use separate mechanical switches for such keys If substantial amounts of metallic dust water or liquids enter the FP unit turn off the power immediately unplug the unit s power and contact your local FP distributor When installing the FP unit be sure to follow the instructions given in Chapter 3 Installation and Wiring to insure it is done correctly Do not use the FP in an environment with flammable gas since it may cause an explosion FP 570 T User s Manual Safety Instructions For the correct use of this unit please follow these guidelines Do not press the screen s touch surface too strongly with either your finger or a hard object since the touch surface may be damaged When the surface of the display screen becomes dirty or smudged clean the display with a cloth soaked in a neutral detergent Do not use paint thinner
38. tings the FP s display click sound and buzzer can all be controlled from the host computer PLC by sending one character touch panel commands to the FP unit The dip switch settings are only enabled when the FP is turned ON co rmon 6Bh Click sound low ON 6Ch Click sound low OFF 71h FP 570T User s Manual 4 Touch Panel Commands p Boot up Initialization When the power is turned ON the touch panel is initialized as follows Clears its internal buffer Initializes the serial communication mode 36000ps Data length Stop bit nitializes the system default values Function Default Setting Display output Backlight Click sound ON or OFF selected with Dip SW1 6 high Automatic OFF mode ON or OFF selected with Dip SW1 5 FP 570T User s Manual Touch Panel Commands 43 Touch Interface Data Since the FP uses an analog type touch panel all 640 x 480 coordinates can be detected Resolution of the analog touch panel is 1024 x 1024 so a conversion program to convert the coordinates to 640 x 480 becomes necessary Also a calibration program to adjust the actual touch position is needed As a result the following software is included with the FP 570T unit ATPH EXE Passes 640 x 480 touch coordinate data to user program This is not a mouse simulation program CALIB EXE Calibrates the touch coordinate data to the actual touch position This program is to be used with ATPH as
39. ual 3 Touch Pe Bundled Software The 3 5 inch floppy disk pictured below included with the FP unit contains the following utilities A touch panel handler for easy detection of touch panel data A calibration program for making touch coordinate adjustments Touch panel handler ATPH EXE Touch panel data calibration program CALIB EXE ava These programs only run on PC AT compatible machines under the MS DOS environment FP 570T User s Manual 5 Touch Panel Communication Program 52 Operation Environment Analog RGB Interface Cable SIO Interface Cable VGA standard Dsub 15 pin Dsub 9 pin female male Personal Computer 3 5 inch FD Touchpanel communication programs 5 2 FP 570T User s Manual Touch Panel Communication Program 53 Touch Panel Input Drivers 5 3 1 ATPH EXE Touch Panel Handler Input for the analog touch panel is carried out at a resolution of 1024 x 1024 dots with the origin point located in the upper right corner of the panel The origin point of the display panel however is located in the upper left corner and its resolution is 640 x 480 dots Since the coordinates of the touch panel and the display panel do not match the ATPH EXE Touch panel handler is used to convert touch panel input data to match the both resolution and the origin point of the di
40. wire as short as possible When using a long grounding wire replace the thin wire with a thicker wire placed in a duct If this equipment does not function properly when grounded disconnect the ground wire from the FG termi nal 3 2 4 Precautions Input Output Signal Lines Input and output signal lines must be separated from operating circuit power cables If this is not possible use a shielded cable and connect the shield to the FP chassis FP 570T User s Manual 3 7 Installation and Wiring 33 Operation Mode Setup and Display Positioning 3 3 1 Operation Mode Setup and Adjustment The setup switches dip switches are located in the rear of the unit FP 570 T rear view Dip switch The default settings for the FP were created based on the standard connection method used with IBM PCs Use these dip switches to control the FP unit s display features If it does not display 1mages properly with the standard settings shown below please adjust the switches SWI Not used Always OFF SW1 6 Turns touch panel input s click sound ON OFF SW1 7 Selects Backlight Automatic OFF mode SW1 8 Selects Display mode Not used Always OFF OFF ON 3 8 FP 570T User s Manual Installation and Wiring SWI 4 This switch is used to designate the FP s display mode Display Mode VGA Standard graphics mode 640 x 480 Dot clock frequency 25 175MHz 1 and Text mode
41. y 3 6 Printer Connection 3 1 3 8 Printer Interface 2 3 Priority Buzzer and Click sounds 4 6 R Reserved Commands 4 6 RGB Interface Cable Pin connections 2 5 Rubber gasket 3 1 S Safety Instructions ii Sampling Rate Screen 4 4 Screen display iii Screen display origin 4 3 Screen flicker 3 10 Serial communication mode 4 2 Serial Interface 2 4 Shielded cable Wiring 3 7 Sideways Installation 3 2 Signal Names 2 3 2 4 SIO Interface Cable 1 1 SIO transmission 3 9 Specifications Electrical 2 1 Environmental 2 1 Interface 2 3 Structural 2 3 FP 570 T User s Manual Structural Specifications 2 3 W Surge Absorber 3 7 Surge absorber 3 7 Wiring 3 5 Switch SW1 4 2 3 Grounding 3 7 Symbols 1 Input Output Signal Lines 3 7 System default values Power Cable 3 5 Initialization 4 2 Power Supply 3 6 SYSTEM ENVIRONMENT SETUP 5 3 SYSTEM SETUP 5 3 5 7 SYSTEM SETUP Touch Buzzer sound 5 3 T Terminals Crimp On Ring 3 5 Termination code Data Format 4 4 TFT Color LCD viii Touch Interface Data 4 3 Touch Panel Command 4 1 Touch Panel Commands 4 5 Touch Panel Coordinate Data 4 3 Touch panel coordinates 5 3 Touch Panel Data Calibration CALIB EXE 5 7 Touch Panel Does Not Work Troubleshooting 6 4 Touch panel input Infinite Wait 5 5 Instant Return 5 5 Non renewing 5 5 Touch Panel Input Drivers Bundled Software 5 3 Touch Panel programs Floppy disk ix Troubleshooting 6 1 TT WIN95 4 3 U User s Manual ix V Vector numb
Download Pdf Manuals
Related Search