Owners Manual - Desert Aircraft Australia
Contents
1. We recommend filtering your fuel between your fuel container and your plane s fuel tank A high flow filter or clunk filter between the tank and motor is also a good idea Make sure the plane s tank is well vented and the fuel clunk mover freely Use of any other fuel or additives such as methanol nitro formulas aviation gas white gas etc can harm the motor and will void the warranty Do not use any silicon sealers on the fuel system Gas can break it down and carry it into the carburetor For Break in we recommend a petroleum based oil such as Castrol Active 2T 33 1 ratio 150ml oil per Sits fuel Run at least 15 to 20 litres of petroleum oil gas mix for break in This procedure shortens the time required to get a good seal on the ring If the ring is not seated correctly blow by will occur which can damage the engine If blow by sets in early the ring and piston may never have a chance Use a prop that allows peak RPM over 6 500 during the break in process Set the High needle slightly rich during break in After the break in process we recommend a high quality synthetic oil As for brand of oil there are many good ones on the market Some oils and their mix ratios that Desert Aircraft recommends are Red line 2 Cycle Racing Oil 40 to 1 Castrol TTS 40 1 These oils can be found at most motorcycle Auto shops Redline can be sourced from DA Australia Mix Ratio 33 1 40 1 50 1 1002. 1 Mls Mls Mls Mls 1 Litre 30 3 25 20 10 5 Litres 151 5 125 100 50 10 Litres 303 250 200 100 15 Litres 454 5 375 300 150 20 Litres 606 500 400 200 Recommended Props e Always tighten prop bolts and inspect your prop and spinner before each flight e While special break in props are not required avoid large heavy load props during the break in period After break in the normal recommended peak RPM range for good performance is 6 300 to 7 300 depending on prop selection e Some recommend props are o For break in Mejzlik 22x8 22x10 23x8 Xoar wood 22x8 Vess 22a or b Mejzlik 21x11 5N 3 blade o After break in Same as above but also Mejzlik 23x10 Mejzlik 20x12 3 blade e Smaller Diameter props with more pitch especially 3 blades will reduce noise but may make the plane fly and land fast e Lower rpm normally equals less prop and engine noise e Always use a drill guide to drill your props e Always check the balance of your prop e For safety we recommend painting the tips of you props front and back with a bright color especially when using black props e Never use a damaged or repaired prop or a prop that has struck the ground or any other object Damage that can be hard to see could turn into disaster when turning at thousands of RPM 10 Starting e Beware of running the engine without the wings installed on the fuselage Without the mass of the wings vibration will be very pronounced e Check t
3. DEFECTIVE BY DESERT AIRCRAFT This warranty does not cover the following e Shipping expenses to and from Desert Aircraft for warranty service e Damage caused by improper handling operation modifications or maintenance e Damage caused by a crash e Damage caused by using improper fuel or additives e Damage incurred during transit to Desert Aircraft pack carefully 15 When returning a product always include a brief note describing the problem along with your contact information Information like type of exhaust system prop size oil type and ratio amount of use etc can be of great help to our technicians See attached form DESERT AIRCRAFT AUSTRALIA Unit 5 74 Secam Street Mansfield Queensland 4122 Ph 07 3422 0772 Fax 07 3420 3250 Email sales desertaircraft com au Web www desertaircraft com au 16 Repair Return Form Customer Details Name Address City State Postcode Phone Number REASON FOR RETURN DESERT AIRCRAFT AUSTRALIA Unit 5 74 Secam Street Mansfield Queensland 4122 Ph 07 3422 0772 Fax 07 3420 3250 Email sales desertaircraft com au 17
4. leans the fuel mixture Turning the needles counter clockwise richens the fuel mixture e Settings will vary with altitude temperature humidity fuel carburetor variances etc A general starting point is 1 5 8 s open on the low needle 1 7 8 s open on the high needle e Adjusting either needle can have a slight effect on the other Example leaning the low needle can slightly lean the high range e Adjust the High needle to peak rpm A tachometer is a great help but remember that the RPM may drop a little bit after every start due to heat build up Don t lean the mixture any more than necessary If the rpm steadily drops at full throttle or fades on long vertical maneuvers the engine is too lean and is over heating e Adjust the Low needle until you achieve a smooth idle and a reliable transition to high throttle Generally if the engine stutters or coughs in the mid range or when the throttle is advanced the Low end is too rich and possibly even the High needle If the engine dies quickly the Low end is probably lean e Set the High needle slightly rich during break in Operating the engine overly rich not only reduces power it creates other problems such as poor transition pre mature carbon build up fouled plugs excessive exhaust residue sticking rings and overall rough running 12 Trouble Shooting e Motor Won t start o Flooding The DA 50R normally only needs to be choked for t
5. that the fuel clunk is intact and can move freely to the correct tank position Check all ignition connections and switches carefully Faulty switches and contacts can cause momentary loss of ignition power due to vibration and harness movement during flight Make sure your fuel is fresh Changes in atmospheric conditions can cause water condensation in gas cans and tanks Look for water in your fuel can and plane s fuel tank Needle settings may need adjustment when the engine is moved from one plane to another or cowl configurations airflow and pressure is changed IF ANY PROBLEM PERSISTS PLEASE CONTACT DESERT AIRCRAFT AUSTRALIA We designed and manufactured your engine We have serviced and trouble shot thousands more We cover your engine s warranty not someone at the field or a stranger on the Internet Please give us the opportunity to help 14 DA 50R WARRANTY Your DA 50R engine and ignition system are covered with a 3 year warranty by Desert Aircraft starting from the date of purchase This warranty covers defects in workmanship and materials only Do not disassemble the engine or ignition system Disassembly of the engine or ignition system will void the warranty on that item Any modifications to the engine or the ignition system other than those authorized by Desert Aircraft will void this warranty WARRANTY ITEMS WILL NOT BE REPLACED OR SHIPPED UNTIL ITEMS IN QUESTION ARE RECEIVED BY AND DEEMED
6. the side of the propeller Always stand behind the propeller Keep spectators at least 30 feet away when operating the motor Turn off the motor before making any adjustments Always use the proper size propeller Never use a damaged modified or repaired propeller Always use the correct length propeller bolts Do not use spacers behind the propeller Spinner cones must not touch the propeller Thinner props may require using shorter prop bolts Please make sure your prop bolts do not bottom out in the propeller hub Check that the propeller bolts are tight before every flight Always install an ignition kill switch to stop the motor Adjust the carburetor linkage so that the motor will stop when the carburetor is completely closed Gasoline is extremely flammable Be careful of any sparks from electrical contacts such as fuel pumps battery chargers etc Do not allow smoking in the area of your fuel supply or motor Store fuel in approved containers and in well ventilated areas Allow the motor to cool before touching or fueling Always turn the prop a few revolutions after running the motor to discharge the ignition system The ignition system develops extremely high voltage Do not touch it during operation Mounting the Engine The DA 50R features a rear induction carburetor that is intended to protrude or breath through the fire wall This carburetor location provides a stable air environment for consistent high performance wh
7. DA50R DESERT AIRCRAFT AUSTRALIA www desertaircraft com au DESERT AIRCRAFT AUSTRALIA Thank you for buying your DASOR Please read this manual carefully before you operate your engine Please be careful when operating your new engine make yours and the safety of others a priority Your new DASOR is a purpose designed model aircraft engine and proper care should be taken when in operation Desert Aircraft Australia is proud to stand by our products and happy to aid and assist you where ever we can If you have any questions regarding your engine and its operation please do not hesitate to call us We are here to help Please be aware that this is a petrol engine and silicone fuel tubing is not suitable Tygon or neoprene fuel tube is required not only to the carburetor but also in the fuel tank Standard unleaded fuel mixed at the required ratio see page 8 is all that is need for running your DASOR Your DASOR is well suited to many kinds of model aircraft from aerobatic scale war birds glider tugs and the likes Propeller selection will depend on the airframe and its intended use see page 10 So recommending the correct propeller is not a straightforward issue Obviously choosing a quality balanced propeller is a must and we will be happy to help with your selection Desert Aircraft Australia Unit 5 74 Secam Street Mansfield Qld 4122 P 07 3422 0772 F 07 3420 6678 sales desertaircraft com au www dese
8. hat prop bolts are tight and spinner is secure e Make sure the starting area is free of dirt sand gavel or other loose debris e Turnon the radio system and check the throttle operation and position e Have someone with eye protection firmly hold the plane e Close the choke completely e Open the throttle to approximately 1 8 position e Turn on the ignition ALWAYS BE PREPARED FOR THE ENGINE TO START ON ANY FLIP OF THE PROP whether the ignition switch is on or off Flipping the prop with the ignition off may flood the engine e Always wear a heavy leather glove when starting the engine e Give the prop a quick firm flip counter clockwise Follow through quickly as you flip the prop so your hand swings out of the props path Repeat until the engine fires or pops Less than a firm flip may cause the engine to bounce off of compression and run backwards e Open the choke e Set throttle to idle position carburetor butterfly plate slightly open e Flip the prop again until the engine runs e Let the engine warm up for 15 to 20 seconds before advancing the throttle e Usually the engine only needs to be choked on the first start of the day e For idle on a single cylinder engine the rom range should be 1700rpm to 1900rpm 11 Needle Adjustments e The needle farthest from the engine is the High End needle The needle closest to the engine is the Low End needle Turning the needles clockwise
9. he DA 50R carburetor is fairly light and most users will leave it as is If you wish the throttles return spring can be released not removed off the end that hooks on the throttle spring return arm Opposite side of the carburetor from the throttle arm The choke lever can be actuated finger or by a small servo behind the firewall Another option is to remove the choke arm and replace it with a nose wheel steering arm Goldberg or equivalent this allows adjustment for linkage access from the bottom or rear Soft mounts can be used but movement of the engine can cause problems with exhaust systems and carburetor linkages Make sure firewall and or motor box are secure Ignition System When making electrical connections to the ignition system use the same gauge wire or larger as used on the red and black power leads on the ignition module all the way to the battery pack Keep wire lengths to a minimum Please use the heavy duty connector plugs supplied with the ignition Use a high quality switch such as a Futaba or JR heavy duty switch Standard size R C receiver switches are not recommended 6 Mount the ignition module on a foam pad with plastic zip ties DO NOT HARD OR VELCRO MOUNT DO NOT USE DOUBLE SIDED TAPE Isolate the charge circuit from the ignition while charging the batteries In other words don t charge the ignition module while charging the battery Use 4 8 or 6 0 volt battery pack Higher voltage w
10. he first start of the day Over choking can cause flooding o Check battery voltage should be at least 5 0 volts and all ignition connections regulators wiring and switches o Check tank venting clunk position and fuel flow o Check all fuel lines for kinks pin holes or damage o Is the crankcase pressure tap sealed 8 32 thread hole in the rear case near the carburetor o Does fuel move toward the carburetor when the prop is flipped o If fuel isn t moving towards the carburetor is the choke plate completely closing Is the carburetor or carburetor mount loose causing an air leak Look for fuel seepage around the carburetor mounting area o Is the throttle set at idle or slightly higher after engine pops and choke is opened o Make sure prop is flipped over with authority The ignition won t fire at low speed o If a lot of fuel drips from the carburetor the engine may be flooded If so remove and dry or replace spark plug Try starting again without using the choke 13 e Motor runs poorly O The engine might be too rich Make sure both needle are adjusted to peak performance Due to changes in air pressure and air flow in the cowl when the plane is flying the needles may need to be adjusted to deal within flight performance not just the way the engine runs on the ground Make sure carburetor has not come loose causing an air leak in the carburetor mounting area Look for fuel seepage Check
11. ile carburetor noise is greatly reduced The width of the motor is also reduced for tighter cowl installations The DA 50R can be mounted with or without the included stand off spacer mounts The spacers are mounted to the motor mount flange tabs with steel M5 metric screws supplied The rear of the stand off mounts are threaded for 4 20 SAE mounting bolts not supplied The engine is mounted to the firewall with 74 20 mounting bolts that pass through the stand offs from the rear of the firewall Note Export Metric versions of the stand off mounts are red color and are threaded for M6 metric screws at the rear We recommend blue Loctite on all engine mounting screws Check the mounting bolts regularly to insure they are tight Be very careful using shims or spacers behind the supplied stand off mounts The rear face of each stand off must be in the same surface plane If they are not in the same plane the mounts and crankcase will be under stress causing damage to the engine Make sure the carburetor has adequate clearance near the inlet to allow an unobstructed airflow into 5 the carburetor We recommend at least 1 25mm of clearance If the carburetor is located in front of the firewall be sure there is at least 1 25mm of clearance from the carburetor inlet If not make a hole larger than the carburetor inlet diameter in the firewall The throttle arm is tapped for a 2 56 SAE ball link The spring tension on t
12. ill damage the ignition system and will void the warranty We recommend a 1500 mAh or larger pack With this size pack the ignition pack should last longer than your receiver pack will If a meter shows 5 0 volts or less don t fly re charge If using a pack rated above 6 0 volts you must use a 5 2 to 6 0 volt regulator Check the output voltage of your regulator We have seen regulators fail allowing excessive voltage to reach the ignition causing ignition failure This will not be covered under warranty Unlike some ignitions the Desert Aircraft ignition is designed to spark only when the prop is flipped at a high speed If the prop is not turned over at starting speed the ignition will not fire This helps to prevent the motor from firing accidentally Unless you are having problems starting the motor don t bother testing the ignition with the plug removed from the cylinder Do not turn the engine over or flip the prop without the caps firmly installed on the spark plugs If the caps are not securely installed the ignition system can be permanently damaged This will not be covered under warranty When removing the spark plug caps PULL STRAIGHT out on the caps not the shielded ignition wires If the cap seems loose and is not making a solid metal to metal contact with the spark plug base contact Desert Aircraft for a replacement To prevent radio interference the spark plug caps must have the split 7 re
13. rtaircraft com au Safety Instructions WARNING This motor can cause severe harm to you and or others if misused or if these safety precautions and instructions are not observed Desert Aircraft is not responsible for any loss injury or damage resulting from the miss use of its products e You alone are responsible for the safe operation of your motor e Do not operate the motor if you do not want to be completely responsible for any damage or injury incurred or caused during it s operation e Read all instructions before operating your motor e If you have any questions about any aspect of operating this motor do not attempt to start or operate it e Never operate the motor or fly alone e Keep away from the prop while operating the motor Do not wear loose clothing near the motor or prop Do not run the motor near loose material such as dirt gravel power cords ropes sand etc Loose material can be drawn into the turning prop causing injury or damage e Always operate the motor in an open area Do not operate indoors e This motor can develop tremendous thrust Make sure the aircraft is properly secured or held when starting or operating the motor e Inspect motor mount bolts and firewall integrity before operating the motor Anyone in the immediate area of the motor should use eye protection during operation of the motor When operating the motor never stand or allow anyone else to stand in front of or to
14. tainer ring around their base DON T FLY WITHOUT THEM e Protect the shielded plug wires from rubbing against fiberglass or sharp edged of wood or metal Rubber grommets and plastic spiral wrap insulation from automotive or electronic supply stores work well Holes in the braided shielding can emit R F noise i e RADIO INTERFERENCE e Keep ignition components and wiring separated as much as possible from your receiver receiver battery servos wiring and switches e Don t use metal to metal linkages to operate the throttle e Always perform a radio range check before flying Range with one section of the antenna extended should be at least 80 to 100 ft with the plane on the ground and the motor running If there are glitches DON T FLY Check for holes in the braided shielding or loose connections spark plug caps connectors and switches If that doesn t solve the problem re locate your ignition and receiver components farther apart If the problem persists return the ignition to Desert Aircraft for inspection e Timing is set at the factory and should not need adjustment Contact Desert Aircraft if you have any questions regarding timing e Only use NGK CM 6 spark plugs Other plugs may not fit the plug caps firmly e Plug gap is 018 to 020 45mm to 50mm Break In and Fuel and Oi Mix e Low octane pump gas is recommended High octane may be beneficial only when using tuned exhaust systems
Download Pdf Manuals
Related Search