Home

18536 WFA WFA12 & WFAPRO1500 Owners Manual

image

Contents

1. e Any failure to install or use the unit in accordance with the Manufacturers Instructions the Installation and Operating manual or WFA s printed instructions or e The purpose for which you are purchasing the unit You acknowledge that the quality of water supplied and your water usage rate and influent water pressure may vary seasonally or over a period of time In addition to this water characteristics can differ if the unit is relocated or the environment changes You acknowledge that WFA does not know your requirements and cannot and does not warrant that the unit is fit for the purpose for which you intend to use the unit or is appropriate for the purpose for which you intend to use the unit WFA does not authorize others to assume any obligation on its behalf even if you inform them of the purpose for which you intend to use this unit WARNING WFA does not recommend making alterations to your existing plumbing to accommodate this filter system If you wish to modify existing plumbing you must comply with AS 3500 and use a licensed plumber Where internal water pressure exceeds 1000 kPa a Watermark approved Pressure Limiting Valve must be installed prior to the filter system WARNING The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water supply Do not use with water that is microbiologically unsafe or of an unknown quality without disinfection before or a
2. including check valve supplied in the water filter system kit IF A SEPARATE WATER CONNECTION IS NOT PROVIDED e Locate the stop tap mounted on the wall underneath the sink for the existing cold water line Turn off isolation Stop Tap and disconnect attached fittings Owners Manual Attach the following parts to the Isolation Stop Cock according to the Connection Diagram below Using plumbing tape e Attach the following parts to the Isolation Stop Cock according to the Connection Diagram below Brass Female Tee 12 BSP Brass Nipple 72 BSP 72 BSP x2 Cistern Tap supplied e Reconnect the cold water line to the available 12 connection Firmly tighten all connections Parts not included with system 3 Undersink Mounting Position As you will note from the associated diagram the Filter System must be installed in the vertical position a Vertical Installation Measure 38 cm from the base of the cabinet or shelf and mark the mounting location for the top of the filter head Make sure that there is adequate space to avoid crimping the water line flex hoses Also make sure your chosen location offers easy access for future cartridge changes Important Changing the inlet and outlet on the filter head You will notice that at the top of the Head Assembly item 4 there is an arrow that indicates the direction of flow into and out of the filter head In some instances to ensure an easier
3. Cistern Tap 72 fosp x 12 mbsp Pex Hose 550mm Dual Check Valve 12 fosp x 1 2 mbsp Filter tap 3 Pex Hose 750mm Filter Monitor Alarm 4 Head Assembly 9 Plumbing Tape Filter Cartridge Mounting Screws WARRANTY Product Specifications The unit must only be used for a portable treatment cartridge if there is a defect in the filter or water source and with cold water with a temperature range cartridge This does not include the replacement of between 2 and 38 C the filter or cartridge to extend the life of the filter or cartridge The life of the filter cartridge is affected by WFA and Everpure Inc warrants to you the first person water quality usage and water pressure The warranty who has purchased and used the unit you that only extends to the original purchaser of the unit this unit is free from defects due to faulty material and a ci What this warranty does not cover workmanship in accordance with the conditions set out y in this document This warranty is provided to you in This warranty does not cover the unit or a Replaceable addition to your rights at law including but not limited to Element of the unit where your rights under the Trade Practices Act 1074 Cth and e The defect fault or failure is attributable or applicable legislation in your Australian State or Territory substantially attributable to misuse abuse accident What this warranty covers misapplication neglect freezing ox
4. IANCE IT IS ESSENTIAL Underwriters Laboratories Inc against NSF ANSI Standards pesky TO OBSERVE THE MANUFACTURER S 42 and 53 for the reduction of Q O INSTRUCTIONS Std No 42 Aesthic Effects Chemical Reduction Chlorine Taste amp Odour Mechanical Filtration Nominal Particulate Class 1 WATER QUALITY Std No 53 WATER FILTER Health Effects ANSI NSF Chemical Reduction casa STANDARDS Mechanical Filtration 42 AND 53 Cyst 3LSD Turbidity Distributed by Water Water Filters Australia Pty Limited ABN 78089 574 489 Unit 1 91 93 Old Pittwater Road Fi ters BROOKVALE NSW 2100 Australia j AUSTRALIA PO Box 636 FRESHWATER NSW 2096 Australia tie gt T 61 2 9905 6211 F 61 2 9905 6255 E info waterfiltersaust com au W www waterfiltersaust com au
5. WFA12 amp WFA PRO1500 Water Filter Kits Owners Manual Thank you for purchasing the Everoure manufactured commercial grade half micron Water Filtration System distributed exclusively by Water Filters Australia WFA You get premium quality filtered water direct from your filter tap that s clean great tasting healthy and convenient for you and your family Water PiE C Water Filters Performance Data Important Notice Read this performance data sheet and compare the capabilities of this unit with your actual water treatment needs FEATURES e Finely polishes treated water to premium quality for drinking and cooking e Reduces chlorine taste and odour e Reduces dirt rust asbestos fibres and other particulates such as oxidized iron manganese and sulphides e Reduces parasitic protozoan cysts such as Giardia Entamoeba and Cryptosporidium e Absorbs common earthy mouldy fishy tastes and odours HEALTH CLAIM PERFORMANCE CLASSIFIED BY UL This system has been tested according to NSF ANSI 42 and 53 for the reduction of the substances listed below The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissable limit for water leaving the system as specified in NSF ANSI 42 and 53 Max Permissible Influent Challenge Product Water Reduction Minimum Average substance Concentration Concentration Requirements Reduction Require
6. aminants or other substances removed or reduced by the water treatment system are not necessarily in your water e Check for compliance with state and local laws and regulations e Tested under sustained standard laboratory conditions actual performance may vary Water MITES INSTALLATION INSTRUCTIONS 1 Open Carton and Inspect Parts Installation Parts included refer installation diagram Item No Cistern Tap 12 fosp x 72 mbsp Dual Check Valve 12 fosp x 12 mbsp Pex Hose 750mm Head Assembly Filter Cartridge Pex Hose 550mm Filter Tap Filter Monitor Alarm Plumbing Tape Mounting Screws OGQCO QOOQHOOHOO IMPORTANT NOTES When installing this filter system in a new home or kitchen please ensure that the cold water lines under the sink are flushed to remove all debris within the pipes before installation of the water filter system This Water Filtration System should be installed in accordance with any local Water Authority by laws Australian Standard AS3500 Where water pressure exceeds 1200 kPa a suitable pressure limiting valve should be installed prior to connection to the filter system Connect to Water Supply Check to see if separate water connection is provided IF A SEPARATE WATER CONNECTION IS PROVIDED e Locate the stop tap cistern cock mounted on wall under the sink Ensure water is turned off at the mains and then replace the existing stop tap cistern cock with the cistern cock
7. e tap Tighten locking nut beneath the sink to secure the tap firmly in position If a hole for the filter tap is not provided then use a drill or hole cutter to cut a 12 7mm 1 2 hole in the sink or counter top where the tap is to be located Attach Filtered Water to Cold Water Line of Filter Tap Take the braided pex hose from the outlet of the head assembly and connect to the bottom of the filter tap Install Filter Cartridge item 5 a Hold filter head firmly with one hand b Align cartridge lug with label on filter head c Insert filter cartridge and push into filter head assembly d Turn it to the right about 1 4 turn until it stops 10 Flush the Filter Cartridge a Turn mains water supply back on at mini cistern tap b At this stage check for leaks and fix if necessary c Turn kitchen filter tap on and flush the filter cartridge for at least 1 2 minutes Collect water in container and use for garden etc NOTE Flushing the filter cartridge is important to remove air from the system and any loose carbon At first the water may appear cloudy due to compressed trapped air in the filter and hoses However the cloudiness will disappear over time and with use 11 Installing the Filter Monitor Alarm item 8 The filter monitor alarm item 8 is supplied to assist you with knowing when it is time to replace your filter cartridge Regular annual cartridge replacement ensures that your filter syst
8. em is maintained in accordance with the manufacturers recommendations a Remove double sided tape and plastic wrapper from monitor b On the back of the monitor pull the tab back c The LED and buzzer will cycle 3 times to confirm the start d It is programmed to flash and sound again in 11 months e Remove the two adhesive tapes from the back of the monitor and locate mount in a convenient location under your kitchen sink NOTES 1 This installation must comply with all applicable state and local regulations 2 Do not use with water that is microbiologically unsafe or of an unknown quality without disinfection before or after the system 3 When storing filtered water in a refrigerator please ensure the container has an air tight seal lid PRODUCT SPECIFICATION e Usage For cold water only e Temperature Range 2 38 C e Min Max Working Pressure 10 125 psi 0 7 8 6 bar e Service Flow Rate Filtered 8 3 Litres per minute cold e Capacity 5 600 litres e Micron Rating Half 0 5 micron e Removes Reduces Chlorine cysts lead giardia cryptosporidium bad taste and odours and all particles down to half micron in size e This filter does not remove fluoride e Filter Change Annually or TOOLS REQUIRED FOR INSTALLATION sooner if flow rate becomes e Philips Head Screwdriver Tape Measure inconveniently slow e Adjustable Wrench e Pencil Subject to water quality and usage Q
9. fter the system IMPORTANT This filter is designed to be used with mains city water supplies If the incoming water is from a water tank or bore install a suitable prefilter prior to this filter system to prolong filter cartridge life CAUTION Safely isolate the water supply prior to installing the filter system to avoid injury and property damage Check for compliance with state and local laws and regulations Product performance is dependant upon incoming water conditions This drinking water system must be maintained according to the manufacturer s instructions including replacement of cartridge AS3497 This appliance meets the domestic water treatment Lic WMKA22045 appliance Standards AS NZS3497 for the following WaterMark IAPMO R amp T OCEANA water treatment processes CLASS TREATMENT TYPE FUNCTION PASS Microbiological Status Will stop bacteria increasing but will N A Bacteriostatic not stop them unless lla is passed Microbiological Treatment Will remove or inactivate bacteria N A Bacteria Removal Virus Removal Will remove or inactivate virus Protozoa Removal Will remove or inactivate J Cryptosporidium and Giardia Will not remove or inactivate bacteria and virus unless Il a and II b is passed Turbidity and Particulate Reduces Cloudiness J Reduction IV Taste and Odour Reduction Reduces Tastes and Odours S WARNING FOR CORRECT OPERATION eee ee OF THIS APPL
10. idizing agents including but not limited to chlorine ozone This warranty covers defects due to faulty material and chioramines and other related components OF actor workmanship of the unit supplied to you God e For a period of 5 years from the date of purchase in The unit has been in conditions which do not conform respect of the entire unit excluding the Replaceable to the recommended design guidelines or has been Elements The Replaceable Elements are consumable operated in a manner which is contrary to WFA s components and all parts of the unit which can be printed instructions replaced including but not limited to the filter or water e The unit has not been installed in accordance with WFA s printed instructions and has not been installed in compliance with all applicable laws regulations and industry standards e The unit has not been used in accordance with the manufacturer s instructions e The unit does not meet the conditions for use described in the owners manual or performance data sheet for this unit e You use accessories or components which do not meet WFA s specifications as set out in the Owners Manual e The defect fault or failure is due to normal wear and tear e The defect fault or failure has occurred where the unit has been used reasonably or has reached its serviceable life e The serial or model number label of the unit is removed or defaced e The unit is serviced modified alte
11. installation it may be appropriate to have the inlet side on the right of the head assembly as opposed to the left hand side which is provided as standard This can be easily done by removing the four 4 screws on the top of the head assembly turn the head around the opposite way and replace the screws ensuring a tight fit This allows flexibility when choosing your desired install location a Apply plumbing tape to the Pex Hose 3 8 male connection item 3 Wrap tape in direction of the thread to ensure a tight fit and avoid leaks Screw this connection to the inlet side of the filter head Repeat same for the Pex Hose Item 6 on the outlet side of the Head Assembly Item 4 Securely mount the Filter Head Assembly item 4 on the cabinet wall using two of the mounting screws item 10 provided WFA12 amp WFA PRO1500 KITS Connect Dual Check Valve item 2 IMPORTANT It is a legal requirement under Australian Plumbing Standards that the Dual Check Valve be installed If this part is not installed all warranties are null and void a Apply plumbing tape to the 1 2 male connection on the outlet of the existing cistern tap Wrap tape in direction of the threads to ensure a tight fit and avoid leaks Screw on the Dual Check Valve item 2 and secure Attach Pex Hose item 3 Connect the 12 female end of the Pex Hose to the 1 2 male end of Dual Check Valve Install the Filter Tap Aseemble and mount th
12. ments Standard 42 Aesthetic Effects Chlorine 2 0mg L 10 Particulate at least 10 000 Class 1 particles particles mL 0 5 to lt 1um Standard 53 Health Effects Cyst Minimum 50 000 L z 99 95 99 99 99 99 Turbidity 11 1NTU 0 5NTU1 98 99 Tested using flow rate 0 5gom pressure 60 psig oH 7 5 0 5 temp 20 C 2 5 C tNTU Nephelometric Turbidity Units WFA12 amp WFA PRO1500 KITS OPERATING SPECIFICATIONS e Capacity 2835 litres e Pressure Requirement 10 125 psi 0 7 8 6 bar non shock e Temperature 2 389 C e Flow Rate 1 9 litres per minute GENERAL INSTALLATION OPERATION MAINTENANCE REQUIREMENTS e Space required 38cm x 13cm including 6cm of clear space for cartridge change e Install cartridge vertically e Flush new cartridge at full flow for 2 minutes until air is purged e Replace cartridges when capacity is reached or when flow becomes too slow but at least annually SPECIAL NOTICES e Installation instructions parts and service availability and standard warranty are included with the product when shipped e This drinking water system must be maintained according to manufacturer s instructions including replacement of filter cartridges e Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts e The cont
13. red or repaired by an unauthorized or unqualified person How to make a claim under this warranty To make a claim under this warranty you must contact WFA within 21 days of the defect fault or failure occurring WFA Warranty Contact number is 1300 785 355 At the time of repair or replacement under your warranty claim you must provide to WFA e Proof that you purchased the unit from an authorized retailer or dealer within the warranty time and e A copy of a certificate which certifies that the unit was installed in compliance with our printed installation instructions and all applicable laws regulations and industry standards WFA will only pay for repair or replacement upon receipt of proof of your purchase showing the date of purchase Limitation of Liability of WFA under this warranty Where a warranty exists or is implied by law WFA s liability is limited to the extent that it can be limited to repair or replacement of the faulty Replaceable Element or the unit or an equivalent unit WFA may in its discretion choose whether it shall repair or replace any unit or Replaceable Element or WFA may choose to pay to you the cost of replacing the Replaceable Element or the unit or the cost of having the unit repaired To the extent permitted by law WFA assumes no liability whatsoever and disclaims all liability for direct indirect or consequential loss or special general or other damage or expense caused by or arising out of

Download Pdf Manuals

image

Related Search

Related Contents

DIET Users Manual  Air King Dehumidistat DH55 User's Manual  Hotpoint SE103PGX  Deutsch - Heddier Electronic GmbH  440bx mainboard    Samsung RW33EBSS Priručnik za korisnike  高輝度・高精細DLP®プロジェクター  テレビ&ナビューティリティーキッ ト TN-308H 取扱説明書/狂暴  

Copyright © All rights reserved.
Failed to retrieve file