Model G-7 Owners Manual
Contents
1. main display The menu timer is adjustable in increments of seconds Press the UP key until the display reads Set menu timer Press ENTER The display will read Change timeout to Use the UP DOWN keys to scroll up or down to the desired timeout When scrolling in either direction press ENTER to select the desired timeout RESET METER This feature clears data memory and restores default parameters as follows Grain first in list Barley Temp Mode AUTO Temp Scale Fahrenheit Alarm Set Point 15 096 All Offsets 0 Menu Timer 4 secs Off Timer 4 minutes esogezs 6 of 16 Press the UP key until the display reads Reset meter Press ENTER to reset meter The display will read Memory storage is cleared Meter is reset 7 of 16 The following functions are stand alone functions accessed by scrolling up or down the main menus They are not part of the Setup Menu CHECK METER CALIBRATION Press the UP or DOWN key until the display reads Cal test Press the Enter key and the meter will go through the following sequence Measured nominal 14 0 Then it will display mc 14 0 Then it will read Calibration Pass gt The meter is considered in calibration if the display reads 14 0 5 gt If the calibration does not pass the sequence will end with a Calibration Failed display CHANGE THE SET POINT The set point is a user adjustable MC value that will fl2. match the readings of the commercial grain elevator The offset may be changed in increments of 0 1 Before changing the offset we recommend that you determine the average of at least three tests with the G 7 on the sample that was tested with the elevator meter If you accept the elevator moisture meter as a standard then adjust the MC offset to match the elevator 5 of 16 Press the UP key until the display reads Set MC offset Press Enter to change the MC offset Use the UP DOWN keys to scroll forward or backward to the offset value desired When scrolling in either direction press ENTER to select the desired offset SET OFF TIMER The off timer allows you to change the meter s automatic shut off in one minute increments The default setting is four minutes If the meter reads only a LO reading or no key has been pressed for four minutes the meter will shut off automatically Press the UP key until the display reads Set Off Timer Press the ENTER key to enter this mode The display will read Change off timer to Press the UP DOWN keys to select the desired increment of the timer When scrolling in either direction press the ENTER key to select the desired timer increment SET MENU TIMER The menu timer allows you to change the amount of time in which a menu will timeout if no key is pressed If no key is pressed in the amount of time set on the timer the display will revert back to the
3. pressure in a standard bale of hay If you do not have the 831 short pin prod squeeze a handful of hay around the tip of the 830 2 for an estimate of windrow moisture levels For more detailed information about using the G 7 on hay please call Delmhorst Instrument Co at 877 DELMHORST Or you may download any of the owner s manuals for our hay moisture meters from our web site at www delmhorst com 12 of 16 SECTION C FACTORS AFFECTING YOUR READINGS GRAIN TEMPERATURE Wide differences may exist between the grain temperature and that of the instrument Under such conditions the temperature of the samples may change so that it becomes difficult to measure it accurately MOISTURE DISTRIBUTION This condition prevails when grain is drying especially when using heat or rapid circulation of air Differences in moisture content are also found in different parts of the same field because some parts may mature at different times Actual differences in moisture content can also be found in a single ear of corn moisture usually being greater near the stalk SAMPLE SIZE The G 7 tests a small sample and therefore its reading is directly related to the moisture content of the grain from where the sample was selected If the initial two or three tests indicate uniform moisture content there is no need to make additional tests on other samples On the other hand if the initial tests indicate considerable variations in moisture co
4. the seed is at a safe level of moisture content A reading of 1496 indicates a borderline condition of moisture content In this case additional readings are recommended TESTING HAY Setthe meter to Hay TESTING BALED HAY gt Screw the optional 4830 2 10 prod into the H 3 handle and connect the electrode cable to the external connector on top of the moisture meter gt Insert the probe into the bale Pressthe ENTER key to store the displayed reading in memory TESTING IN THE WINDROW gt Attach the 831 short pin prod to the H 3 handle and connect the handle to the external connector on top of the meter Prepare a representative sample by collecting hay from various parts of the windrow Place hay in a non conductive container such as a 5 to 10 gallon plastic pail and apply the short pin prod to the hay Press down on the electrode until the head of the screw which holds the pressure button touches the palm of your hand Pressthe ENTER key to store the displayed reading in memory Mixthe sample once again and take at least two more readings Use the highest readings When testing in the windrow push down on the pressure button until the palm of your hand touches the screw that holds the key in place The pressure button depresses a calibrated spring inside the handle When the screw touches the palm of your hand the pressure applied on the sample is 27 30 Ibs which closely simulates the
5. Delmhorst Instrument Co Model G 7 Owners Manual TABLE OF CONTENTS 2 INTRODUCTION 3 G 7 FEATURES 4 SECTION A METER OPERATION 4 KEY SWITCH FUNCTIONS 4 SET UP MENU 4 TO ACCESS THE SET UP MENU 5 TEMPERATURE MODE 5 TEMPERATURE SCALE 6 MC OFFSET 6 SET OFF TIMER 6 SET MENU TIMER 7 RESET MENU 8 CHECK METER CALIBRATION 8 CHANGE THE SET POINT 8 LOW BATTERY INDICATION 8 SELECT THE GRAIN 9 STORAGE MENU 9 TO ACCESS THE STORAGE MENU 9 VIEW READINGS 10 VIEW STATISTICS 10 TO CLEAR MEMORY 11 SECTION B TAKING A READING 11 TESTING GRAINS 11 TESTING GRAIN AND SEED IN BAGS 12 TESTING FESCUE AND OTHER GRASS SEEDS 1 of 16 12 TESTING HAY 13 SECTION C FACTORS AFFECTING YOUR READINGS 13 GRAIN TEMPERATURE 13 MOISTURE DISTRIBUTION 13 SAMPLE SIZE 14 UNIFORMITY OF SAMPLE 14 CARE OF YOUR METER 15 SERVICE FOR YOUR METER 16 WARRANTY IMPORTANT NOTE When turning G 7 ON allow it to run through its entire initialization before pressing any keys Any interruption to the initialization power up will result in a Calibration Fail when performing a calibration check If this occurs reset the meter power it down and then power it up properly INTRODUCTION Thank you for purchasing the G 7 Grain Moisture Meter The G 7 is a full featured meter that incorporates a double disc pressure type electrode The lower disc forms the base of a shallow cup in which the grain sample is placed The upper electrode screws down over the sa
6. Turn the upper electrode counter clockwise empty the cup and clean it with the brush in preparation for next test TESTING GRAIN AND SEED IN BAGS gt Screw the optional 832 long pin prod into the H 3 handle and connect the electrode cable to the external connector on top of the moisture meter gt Push the 832 prod into the seed bag and Press down on the electrode until the head of the screw which holds the pressure button touches the palm of your hand Pressthe ENTER key to store the displayed reading in memory NOTES Make several tests on various parts of the bag Push the prod into the lower portion of the bag being tested or into one of the bags on the bottom of the pile You may stand on a bag and apply the electrode between your feet When using the 832 Long Pin Prod the following correction should be added to the meter readings Oats Corn Wheat 1 096 Rye Sorghum Soybeans 2 096 Barley 1 596 Rough Rice Coffee 2 596 TESTING FESCUE AND OTHER GRASS SEEDS Screw the optional 2832 long pin prod into the H 3 handle and connect the electrode cable to the external connector on top of the moisture meter Setthe meter to HAY gt Push the 832 prod into the seed and Press down on the electrode until the head of the screw which holds the pressure button touches the palm of your hand Pressthe ENTER key to store the displayed reading in memory 11 of 16 NOTE A reading of 12 normally indicates that
7. ace when the meter is not in use Change the 9 Volt battery as needed Continued use with a low battery may cause the meter to go out of calibration Clean the meter with any biodegradable cleaner Use the cleaner sparingly and on external parts only Keep cleaner out of the external connector Brush off excess material from the sample cup and upper electrode assembly after each use Remove the battery if the meter will not to be used for one month or longer 14 of 16 SERVICE FOR YOUR METER Before sending in your meter we recommend you give one of our trained technicians a call Many times troubleshooting can be taken care of over the phone Call us at 877 DELMHORST Pack your meter securely Enclose a purchase order or letter with a brief description of the problem There is no need to call us for a return authorization number if you are within the U S Customers outside the U S must contact us for more specific instructions prior to returning a meter Include your name address daytime phone and fax numbers or e mail address If you believe the meter is under warranty please provide the original sales slip or invoice Ship via UPS Express Mail Priority Mail or any overnight courier who provides prompt service Do not use standard parcel post Insure your instrument for its full value and ship prepaid We are not responsible for damage in transit We do not accept COD shipments or cover any incoming freight or dut
8. ash two arrows in an upward direction on the display screen if the meter reads higher than the selected value The set point value may be changed in increments of 1 0 Press the UP key until the display reads Change Setpoint Press ENTER The display will read Change Set Point Alarm To Use the UP DOWN keys to scroll up or down to the desired set point When scrolling in either direction press ENTER to select the desired set point LOW BATTERY INDICATION The meter displays BATTERY LOW when the battery voltage drops to approximately 5 8 volts This is an indication that the remaining battery life is 1 1 2 hrs of continuous on time SELECT THE GRAIN Tochange the scale press the UP DOWN key until the display reads Select grain Press ENTER to view the available grains The meter will display Change Grain to gt Using the UP DOWN keys to view the list of grains Press Enter to select the desired grain 8 of 16 Note ifyou do not press the ENTER key after having reached your desired setting for any of the above selections the meter will remain at the previous value prior to scrolling in either direction STORAGE MENU The storage menu of the G 7 allows you to view any stored readings and display various statistics about those readings It also allows you to clear the memory TO ACCESS THE STORAGE MENU Press the UP DOWN keys until the display reads Storage Menu Press ENTER The follo
9. d batch and the co efficient of variation Definition of standard deviation and co efficient of variance is as follows Standard Deviation is a statistical parameter that gives the user in one single figure an indication of the range of readings that make up the AVERAGE The lower the standard deviation the closer all readings are to the average indicating a uniform distribution of moisture content throughout the batch or load Cov or co efficient of variation is a term used to express the standard deviation as a percentage of the average Its values are between 0 0 and 1 0 and again a low COV would indicate a more uniform distribution of moisture 3 Low High The meter displays the lowest and highest reading for the stored readings in the selected batch TO CLEAR MEMORY This function allows you to clear the stored readings while maintaining all other settings such as grain temperature mode etc Press the UP key until the display reads Clear Memory gt Press the ENTER key The display will read Memory storage is cleared 10 of 16 SECTION B TAKING A READING TESTING GRAINS Fill the sample cup with a single layer if grain or seed and place it on the pressure plate Place electrode upper plate in position Turn the electrode screw until you feel some resistance to turning it Then turn it an additional one and a half turns Pressthe ENTER key to store the displayed reading in memory
10. h the warranty shall be void At our option we may replace or repair the meter Delmhorst shall not be liable for incidental or consequential damages for the breach of any express or implied warranty with respect to this product or its calibration With proper care and maintenance the meter should stay in calibration follow the instructions in the Care of Your Meter section Under no circumstances shall Delmhorst be liable for any incidental indirect special or consequential damages of any type whatsoever including but not limited to lost profits or downtime arising out of or related in any respect to its meters or electrodes and no other warranty written oral or implied applies Delmhorst shall in no event be liable for any breach of warranty or defect in this product that exceeds the amount of purchase of this product The express warranty set forth above constitutes the entire warranty with respect to Delmhorst meters and electrodes and no other warranty written oral or implied applies This warranty is personal to the customer purchasing the product and is not transferable INSTRUMENT CO WHEN ACCURACY IS THE POINT Delmhorst Instrument Co 51 Indian Lane East Towaco NJ 07082 877 DELMHORST www delmhorst com e mail info delmhorst com For 60 years Delmhorst has been the leading manufacturer of high quality moisture meters and thermo hygrometers Today we offer the innovative KIL MO TROL in kiln monitoring
11. mple cup Both discs have sharp points that penetrate the seed coat and make contact with the interior of the grain This system rests on a pressure plate that is mounted on a pretensioned calibrated spring insuring uniformity of pressure from one test to another for optimum repeatability The G 7 has been calibrated against well conditioned samples whose moisture content was determined by standardized approved methods In these laboratory tests it was found that the readings are on the average within 0 5 in the range 9 to 17 and 1 0 in the range 17 to 23 The operating instructions for the G 7 are divided into three sections Section A Meter Operation is a step by step guide to the different features and basic use of your moisture meter Section B Taking a Reading contains information on how the meter is used for testing different grains Section C Factors Affecting your Readings discusses various factors that may affect your readings Please read the instructions carefully If you require additional information contact Delmhorst for assistance at 877 DELMHORST 2 of 16 G 7 FEATURES Designed to check moisture levels in the following grains and hay Barley Coffee Corn Flax Hay Oats Rapeseed Rough rice Rye Sorghum Soybeans Wheat Nominal Range 996 3096 MC depending on grain Built in temperature correction User programmable offset Stores up to 150 readings Adjustable set point indicator Digital read
12. ntent among the various samples we recommend that you test more samples in order to have a more accurate determination of the average moisture content and the range of moisture present UNIFORMITY OF SAMPLE When checking the operation of a dryer select samples of grain from different locations to determine how well the drier is performing since the drying rate may not be uniform throughout the grain Also when checking the moisture content of grain in a bin it is necessary to select various samples from different parts of the bin and test them individually In such cases it is very important to ascertain that there is no grain in any part of the bin with a moisture content too high for safe storage It is more important to know the range and distribution of moisture in stored grain than it is to know the average moisture content since an average may not reveal the presence of high moisture pockets Moisture migration may result in an accumulation of moisture in the top layers of the grain It is necessary therefore to take at least one sample from this area when checking the moisture content of grain in a bin Proper use of a moisture meter will show when to ventilate a bin and when fans can be shut down These tests can be made in a very short time 13 of 16 CARE OF YOUR METER To keep your meter in good working order Store your meter in a clean dry place The protective carrying case provided is an ideal storage pl
13. out Includes 1 9 Volt Alkaline Battery Proven microcontroller circuit One year warranty VVVVVVVVVV VV VVVVVVV VV 3 of 16 SECTION A METER OPERATION KEY SWITCH FUNCTIONS 1 ON OFF Turns the meter on and off The G 7 has an automatic shut off feature which turns the meter off after 4 minutes of either LOW readings only or no key activity The 4 minute timer is user adjustable 2 ENTER The ENTER key accepts a selection you make for the various functions made available through the menus This key also stores displayed reading in memory NOTE If you do not press the ENTER key to execute a particular function the selection will not be accepted and the display will return to the main menu 3 UP Allows you to scroll up the menu options 4 DOWN Allows you to scroll down the menu options SET UP MENU The set up menu is accessed by using the UP DOWN keys Within the set up menu are a number of preferences you may set before using the meter Below is a description of those functions TO ACCESS THE SET UP MENU Press the UP DOWN key until the display reads Setup Menu Press ENTER The following setup functions are accessed in this order by pressing the UP key These instructions assume that you have already accessed the Setup Menu as described above 4 of 16 TEMP MODE The G 7 defaults to a temperature of 80 F As grain temperature increases indicated moisture content rises Lower grain
14. system We also offer a wide range of meters for a variety of applications including woodworking lumber agriculture construction paper restoration AQ and flooring 2001 Delmhorst Instrument Co Rev B 04 05 Rev 9 05 16 of 16
15. temperatures result in lower indicated moisture content The temperature modes are AUTOMATIC A built in temperature sensor measures the temperature of the grain sample Let the grain sample remain in the sample cup for at least 5 minutes prior to taking a reading to allow the meter to correctly read the grain temperature The meter will then display a temperature corrected reading MANUAL Allows you to manually input the grain temperature as taken with an external thermometer or temperature system After the temperature is input the meter will display a temperature corrected reading Do not use the manual temperature mode unless you are confident that the temperature of the grain and the temperature of the meter are essentially the same To change the temperature mode Press the UP key until the display reads Temp Mode Press the ENTER key to select a temperature mode The meter will display the current temperature mode gt To choose the temperature mode press UP or DOWN keys to toggle then ENTER to set TEMP SCALE Press the UP key until the display reads Temp Scale Press the ENTER key to select the temperature scale Fahrenheit or Celsius Use the UP DOWN keys to scroll forward or backward to the temperature scale desired When scrolling in either direction press ENTER to set the desired temperature scale 9eMC OFFSET The YoMC offset allows you to make a correction to the calibration of the meter in order to
16. wing functions are accessed in this order by pressing the UP key These instructions assume that you have already accessed the Storage Menu as described above VIEW READINGS After entering the storage menu the display will immediately read View Readings Press the ENTER key The display will read Select Batch and will list the name of one of the grains which has stored data Note If you have stored readings in batches for a number of different grains you may select the grain to view by pressing the UP DOWN keys until the desired grain is displayed Then Press ENTER to select that grain The meter will display the first reading of the selected batch Press the UP key to scroll to the next stored readings To scroll backward to a previously stored reading press the DOWN key VIEW STATISTICS Press the UP key until the display reads Statistics gt If you have stored readings in more than one batch the meter will display the current grain To view statistics of another grain with stored readings press the UP key until the desired batch is displayed After you have selected the batch press the ENTER key The display will cycle through the following statistics 9 of 16 1 Total Avg The meter displays the total number of readings stored for the selected batch and the average of those stored readings 2 Std Dev Co Var The meter displays the standard deviation for the readings stored in the selecte
17. y charges on returned merchandise Turnaround time on repairs is approximately two weeks We will call you with an estimate if you specifically request one or if we determine that the meter may be too costly to repair Non warranty repairs will be returned via UPS COD unless you have already established other payment terms There is no COD service outside the U S To pay by credit card include the card number and expiration date with your repair We accept Visa MasterCard and American Express Warranty repairs will be returned at no charge if shipped within the U S via UPS Ground Service Freight charges for expedited services i e Federal Express UPS 2 Day UPS 1 Day etc are the customer s responsibility and will be charged as per the above terms 15 of 16 WARRANTY Delmhorst Instrument Co referred to hereafter as Delmhorst guarantees its G 7 meter for one year from date of purchase and any optional electrodes against defects in material or workmanship for 90 days If within the warranty period of the G 7 you find any defect in material or workmanship return the meter following the instructions in the Service for Your Meter section This limited warranty does not cover abuse alteration misuse damage during shipment improper service unauthorized or unreasonable use of the meter or electrodes This warranty does not cover batteries pin assemblies or pins If the meter or any optional electrodes have been tampered wit
Download Pdf Manuals
Related Search