Home

USER GUIDE Model DL160 / DL162

1. Multi function LCD 256 000 values dual channel TRMS AC Voltage or Current 1s to 24h selectable 2000 XP Vista USB port 12 7mm 0 5 LO appears on the LCD Empty battery symbol appears on the LCD 4 AAA Batteries and 1 CR 3V memory button battery CR2032 or equivalent 5 days approximately 9V 0 5A CE CAT III 600V for inside use maximum height 2000 meters 0 to 50 C 32 to 122 F lt 70 RH 20 C to 60 C 4 F to 140 F lt 80 relative humidity Dimensions 114 x 63 x 34mm 4 5 x 2 5 x 1 3 Weight 248g 8 70z Function Range Accuracy Voltage 40Hz to 1kHz 10VAC to 600 0VAC 2 0 t1V Current 50 60Hz 10A to 200 0A 2 0 t1A Copyright 2013 FLIR Systems Inc All rights reserved including the right of reproduction in whole or in part in any form www extech com 5 DL160 EU EN V1 3 7 13
2. EXTECH USER GUIDE INSTRUMENTS Dual Input True RMS AC Voltage Current Datalogger Model DL160 DL162 Introduction Congratulations on your purchase of this Dual Input Voltage Current datalogger With this meter you can monitor and log data Voltage Voltage Current Current or Voltage Current over long periods of time and then easily transfer the data to a pc for viewing and evaluation The LCD display provides real time data Max Min data and time information This meter is shipped fully tested and calibrated and with proper use will provide years of reliable service Safety A Warning Do not attempt to make measurement in flammable gaseous areas e When testing a non insulated cable pay attention to avoid short circuits e Do not attempt to use the instrument when your hand is wet Do not input over range during measurements Never open the battery cover during measurements e Stop using the instrument when there is any structural defect or exposed metal parts Do not install substitute parts or make modifications on the meter e Never replace the battery in moist areas Ensure the meter is disconnected and switch off before opening the battery cover to replace the battery Do not attempt to place the instrument in high vibration areas e Do not expose the meter to direct sunlight high temperature and high moisture environment o Switch off the meter after use Remove th
3. e AAA batteries when the meter will be stored for a period of time e When cleaning do not use abrasives or solvents on the meter use a damp cloth and mild detergent only 2 DL160 EU EN V1 3 7 13 Description and Button Functions 1 SL O o 10 11 12 13 14 LCD Description 00 __ Om E TA aa Auto power off does not apply when recording the REC LILA EOE av meter will automatically shuts off after 5mins without any yi IXI yi button presses m REC Recording status After the record mode is set up by the A software press the START STOP button for more than 4 a poni rina seconds to begin recording This icon will be displayed i and indicates the meter is recording data Press the same button again for more than 4 seconds to stop recording Record until full is selected When the memory is full the datalogger will stop recording O Continuous recording is selected When the memory is full the data will overwrite the oldest data FULL Memory full and recording has stopped LI Battery status when completely filled in black the battery power is full When there is only one section filled in the battery is exhausted and should be replaced with a new one AC adaptor Jack ON OFF Button MAXIMIN Press the button one time to display the MAX maximum reading Press again to display the MIN minimum reading A third press will exit MAX MIN mode The meter wil
4. end user are legally bound Battery ordinance to return all used batteries and accumulators disposal in the household garbage is prohibited You can hand over your used batteries accumulators at collection points in your community or wherever batteries accumulators are sold Disposal Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle Software Introduction 1 2 Place the CD in the drive and then follow the on screen installation instruction After the software is installed keep the CD in the drive and connect the datalogger to the PC by the USB cable A USB Driver installation window will pop up Follow the directions to install the driver System Required Windows 2000 or Windows XP or Vista Minimum Hardware Required PC or NoteBook with Pentium 90MHz or higher 32 MB RAM At least 7 MB byte hard disk space available to install Datalogger USB software Recommended display resolution 1024X768 with High Color 16 bit Software Operation The Software operation is described in the HELP file located on the software disk 4 DL160 EU EN V1 3 7 13 Specifications Display Maximum data points Channels Sample rate Analysis software Data output Current Clamp Jaw opening Open input indication Low battery indication Power supply Battery life AC Adaptor Standards Operating Temperature Operating Humidity Storage temperature Storage Humidity
5. l automatically exit MAX MIN mode in 10 seconds if no button is pressed CH Input Jacks Insert the current or voltage sensor to these ports to measure and record the data CHANNEL Select the channel for display on the LCD START STOP After the datalogger is setup from the software press the START STOP button for 4 seconds to begin recording Press the button again for 4 seconds to stop recording Recording cannot be started again until the data is downloaded to the software USB Port AC Current Clamp Jaw Clamp the jaws around a single conductor for AC current measurements to 200A Jaw Opening Trigger CH Plug AC Voltage Probes or Alligator clips Voltage module CH Plug 3 DL160 EU EN V1 3 7 13 Operation 1 2 3 4 Install 4 fresh AAA batteries or connect the AC adaptor Set up the datalogger using the software provided Connect the voltage test leads or the current probes to the AC source to be measured Press and Hold the START STOP button for four seconds to start recording The REC icon will appear in the display indication that recording has begun Press and Hold the START STOP button for four seconds to stop recording The REC icon will disappear from the display Remove the probe connect the datalogger to a PC and use the supplied software to download the data Note If the clock does not set to the correct time replace the 3V button battery You as the

USER GUIDE Model DL160 / DL162

Contents

Download Pdf Manuals

Related Search

Related Contents