LDAL310S User Guide
Contents
1. Dual Axis Laser with Gradient LDAL310S User Guide _ Lufkin LDAL310S A Dual Gradient Laser of extremely rugged design for civil and construction engineering applications High precision Rotary Gradient Laser 5 horizontal self levelling range accuracy 0 5 mm 10 m Gradient can be set digitally in both X and Y axes Electronic vials and positioning motors controlled by temperature stable sensors for automatic horizontal alignment Highest reliability is guaranteed through the ant drift system ADS The electronics permanently monitor the measuring process and switch the laser off in the case of any outside interference or disturbance The laser beam can be switched off in sections Laser modes rotary and hand receiver mode High maximum speed of 1100 rpm the telescopic sight supplied with the device makes alignment easy large illuminated LCD General safety instructions Caution Do not look directly into the beam Lasers must be kept out of reach of children Never intentionally aim the device at people This is a quality laser measuring device LASER RADIATION and is 100 factory adjusted within the stated DO NOT STARE INTO AHE BEAM tolerance For reasons of product liability we must lt 1 mW 635 nm also draw your attention to the following Regularly EN 60825 120010 J check the calibration before use after transport and after extended periods of storage We also wish to point out that absolute calibration is only2. 0 300 600 1100 rpm Digital slope Press the X button 27 The first digit starts to flash Press function the plus minus buttons 28 to enter a positive zero or negative value Press the X button to select the values of subsequent digits Numerical values can be set using the 28 28 plus minus buttons 28 The Y button functions in the same Q way as the X button 27 31 Important You must confirm your entries by pressing Enter 29 the rotary laser will then set the required value Value entry is disabled during levelling SLOPE flashes on the LCD 19 Once levelling is complete and value entry has been reactivated SLOPE will stop flashing and will be displayed permanently on the LCD Manual slope This function is used to deactivate automatic levelling function Large deviations from the horizontal and vertical planes can now be set using an optional external tilt plate To do this press the auto man button 32 MAN will appear on the LCD 24 Note The DualAxis Laser is not capable of motorized slope adjustment in auto man mode Important As the automatic sensors are not active horizontal levelling is not possible Lufkin LDAL310S Tilt function 33 Laser segment mode llluminated display Power manage ment Calibration Once the rotary laser has been levelled and the automatic sensors are running press the tilt button 33 It takes approximately 30 seconds to activat
3. Make sure that you do not reverse the polarity Replace and close the cover completely amp Laser Area Mode e The operating range of the laser beam can be divided into segments The individual segments of the laser beam can be deactivated This is important if a number of rotary lasers are in use on the same site e Use the segment button 30 to select the 4 segments and the plus minus o f buttons 28 G to activate or deactivate the required segment e Confirm the setting by pressing Enter 29 This will restrict the laser s active range to the required segments Rotary mode You can use the rotation button 35 to set various speeds stop 300 600 and 1100 rpm Detector mode Working with the laser detector Press button 17 to switch the SensoLite laser detector on Set the maximum speed of 1100 rom using the remote control or on the rotary laser button a 35 The laser detector is now able to detect the laser beam reliably up to 300m Move the laser detector up and down through the laser beam until the middle indicator 13 appears Mark the measured height at the perimeter marking groove SpotLite Marking The projected light beam at the height of the laser beam simplifies precise marking and prevents parallax errors Spotlite AN Marking Wg Lufkin LDAL310S Calibration Check To check the calibration of the LDAL310S Laser place the Laser on a surface or prefer
4. possible in a specialist workshop Calibration by yourself is only approximate and the accuracy of the calibration will depend on the care with which you proceed Note This product is a precision instrument that must be handled and treated with care Avoid shocks and impact Always keep and carry in the case Switch laser off For cleaning use a soft cloth and glass cleaner Warranty The warranty period is two years from the date of purchase The warranty covers all material and manufacturing defects occurring during this time The following are excluded from warranty Damage due to improper use e g connection to an unsuitable power source falling onto a hard surface etc improper storage normal wear and tear minor defects not impairing operation Any tampering by unauthorized persons will render the warranty void In the event that you need to claim warranty please return the complete device together with proof of purchase to the place of purchase or to the Service address on the back page Quick Reference Guide Switching the Switch the unit on using the ON OFF button 34 The laser unit on for the rotates at a speed of 600 rom and the automatic sensors first time are active Remote control The remote control can be used to control all functions except gradient entry Standby mode is activated by pressing the standby button 37 All settings are retained Rotating speed Press the rotation button 35 to switch speeds
5. Laser 35 Select rotation speed 0 300 600 1100 rpm 36 Calibration mode indicator 37 Activate standby mode on DualAxis Laser All settings are retained 38 Calibration mode switch X Y axis 39 Calibration mode adjusting axis 40 Enter button for calibration mode save new setting 41 LEV Laser out of level Lufkin LDAL310S Sensor Automatic AUTOMATIC The DualAxis Laser is of the self levelling kind After it has been put in the required basic position fine adjustment is being made automatically Horizontal and vertical adjustments are made by the self levelling system SLS while the X axis and the Y axis are scanned by two electronic measuring sensors The working angle is 5 Digital slope adjustment With special slope sensors the operating plane can be inclined The inclination of the X and Y axis can be adjusted separately up to 7 999 The large LC Display shows the exact values ADS Anti Drift System ADS The Anti drift system ADS is to prevent measurement errors caused by movement of the Laser or tripod To activate the ADS press the TILT button after the Laser has been switched on The TILT LED will flash and 30 seconds later the ADS becomes active If the laser is now moved for any reason the ADS will stop the Laser and the TILT LED will illuminate continuously This is to prevent further readings and possible errors until the unit has been suitably checked To cancel the ADS switch the L
6. ably a tripod approximately 10m from a wall or post with the control panel away from the wall or post 1 Switch on the Laser 2 Mark the level point on the wall or post and label this point A using the detector 3 Rotate the Laser on the surface or Tripod 180 Be certain NOT to move or adjust the tripod Mark the level point on the wall or post and label this point B You have now checked the Y axis Max 4mm The point half way between points A and B is true level If A and B are 4mm apart or less then no adjustment is required To check the X axis rotate the level by 90 so that one of the sides is towards the wall or post 4 Mark the level point on the wall or post and label this point C 5 Rotate the Laser on the surface or Tripod 180 so that the other side is towards the wall or post Be certain NOT to move or adjust the tripod Mark the level point on the wall or post Max 4mm and label this point D You have now checked the X axis The point half way between points C and D is also true level and should be the same as that noted for the Y axis above If points C and D are 4mm apart or less then no adjustment is required Note the maximum adjustment is 20mm so if more than this is required then return the Laser to Cooper Tools service dept Lufkin LDAL310S Resetting the calibration 1 T
7. aser Off and then On Attention The ADS function will switch on the control of the laser 30 sec after the laser has completely been levelled adjustment phase Tilt display C emits long blink signals during the adjustment phase and short blink signals when ADS is activated Operating mode ADS ON Rotation ADS in focus after The laser stops rotating begins 30 sec to prevent errors o Adjustment phase Sensor Activate ADS Please External Automatic press tilt button influence Lufkin LDAL310S Set up e Set the unit up on a surface that is as level as possible or fasten it to a tripod ae e Press the ON OFF button 34 on the rotary laser gt e The unit will level itself automatically to within 5 Once levelling is complete the laser will rotate at a speed of 600 rpm The speed can be modified 0 300 600 1100 rpm using the rotation button 35 The laser will flash whilst the laser is being levelled Important The high measuring accuracy means that automatic levelling can take up to 3 minutes e BackLight Press and hold down button 29 Q on the rotary laser for at least 2 seconds to switch the illuminated display on Press the button again to switch it off e Press button 17 to switch the SensoLite laser receiver on The laser beam can now be received Please note that the laser receiver will respond more quickly if the rotary laser is set to a higher speed Note If the unit is set to an exce
8. e tilt If you move the unit during this time it will switch itself off The laser and TILT 22 flash Press the tilt button again to reactivate the automatic sensors tilt will be reactivated within approximately 30 seconds Once the tilt function has been activated it can be deactivated by pressing the tilt button again Important The tilt function is not active in standby mode Press the segment button 30 The top segment 21 flashes on the LCD Use the plus minus buttons 28 to activate deactivate the segment Press the segment button again to move to the next segment Press Enter 29 to confirm the setting and transfer it to the laser Press and hold down Enter 29 on the rotary laser for at least 2 seconds to activate deactivate the illuminated display The unit can run on rechargeable batteries standard alkaline batteries and a mains power supply Running the unit on a mains power supply will charge its rechargeable batteries Press and hold down the auto man button 32 With the auto man button held down press the ON OFF button 34 until CAL 36 appears on the display Open the calibration compartment on the remote control unit and select the X axis by pressing the X Y button 38 You can now set the selected axis using the plus minus buttons 39 Proceed in the same way to set the Y axis Save the new setting by pressing Enter 40 Lufkin LDAL310S Operation of the DualAxis Laser Charging the batte
9. for this digit Use the X button 27 amp to select the values of subsequent digits Numerical values can be set using the plus minus buttons 28 Press Enter 29 to confirm your entry once the entire value has been set sr 1 The unit will then apply the required value 1 Important Value entry is disabled during levelling SLOPE flashes Wie a on the LCD 19 Once levelling is complete and value entry has W been reactivated SLOPE will stop flashing and will be displayed permanently on the LCD e To set the Y axis press the Y button 31 and proceed in exactly the same way as when setting the X axis e Note The automatic sensors are active for the digital slope function Manual gradient function e The automatic sensors are not active when this function is selected al significant deviations from the horizontal and vertical planes can now be configured To do this press the auto man button 32 MAN appears A on the LCD 24 e Adjust the unit to the desired angle The slope can be set easily using the optional tilt plate LLTP1 p e Important Auto man mode does not support horizontal levelling A In 2 planes W since the automatic sensors are not active Lufkin LDAL310S Laser modes These modes can also be controlled with the Commander DAL 50 at distances of up to 50 m away from the unit To insert the battery open the compartment completely as shown on the right
10. o recalibrate the LDAL3108 firts perform the calibration check Important Use the buttons on the calibration panel 28 Calibration 2 During calibration pay attention to the alignment of the axes on the panel LDAL310S Always calibrate both axes 3 Switch the device to calibration mode t switch off the LDAL310S and then switch it on again while pressing the auto man button 32 by pressing the ON OFF button friefly Keep the auto man button 32 depressed until the message CAL 36 appears on the LCD display You can toggle between the axes with the X Y button 38 6 on the remote control The laser begins to rotate as soon as the X Y button is pressed 4 Correcting the calibration Using the plus minus buttons 39 on the remote control you can move the laser up or down until the laser beam is at the True Level position midway between A amp B or C amp D as determined during the calibration check 5 Ending the calibration Save The new calibration is saved by pressing the Enter button 40 GD on the remote control After saving switch off the LDAL3108 The new setting becomes active when the device is switched on again TIP Save every axis individually Cancel The entire calibration is aborted and the previous status is restored if the device is switched off before the Enter button has been pressed X Y axis Note Regularly check the calibration before use after transport and afte
11. r extended periods of storage Always make sure to check both axes Lufkin LDAL310S DualAxis Laser Self levelling range 5 Adjustment speed approx 60 sec on entire working angle Horizontal levelling automatic with electronic vials Digital slope adjustment X axis 7 999 Y axis 7 999 X axis Y axis 10 Precision of the digital slope 3mm 10m adjustment 0 300 600 1100 rpm Class 2 EN 60825 1 2007 10 approx 80 h 4 x Typ D Mono 1 5 V Weight OOOO O O SensoLite 310 Commander DAL 50 Batteries SensoLite 310 1 x 9V battery each Commander DAL 50 Range Commander DAL 50 max 15 m IR control Laser reception range SensoLite 310 Operating temperature 10 C 50 C Storage temperature 10 C 70 C LDAL310S User guide rev a COOPER Tools GUARANTEE This product is guaranteed against any defect in material or workmanship for two years Damage caused by abuse improper use or excessive wear is not covered by this warranty Claims should be returned to the place of purchase or returned prepaid to COOPER TOOLS PTY LIMITED Incorporated in N S W A B N 50 002 965 826 519 Nurigong Street ALBURY A WARNING N S W 2640 Australia
12. ries e The battery symbol 26 will flash constantly on the LCD I to indicate that the batteries need changing or recharging e Open the battery compartment K insert the batteries and connect the plugs to the sockets The plugs fit in the sockets in one position only see pictures on right Reclose the battery compartment e Connect the battery charger mains unit to a mains source and plug into the socket F Please only use the charger mains unit supplied with the device If a different one is used the warranty will become void e The device can also be operated with standard alkaline batteries 4 x type D Insert the batteries as shown by the installation symbols Ensure the polarity is correct Inserting batteries into the SensoLite laser receiver e Open the battery compartment 8 and insert the battery according to the installation symbol making sure that you do not reverse the polarity Replace the cover e In order to save battery power the receiver will switch itself off automatically after approximately 5 minutes of inactivity Note Do not expose batteries to excessive heat such as sunshine fire etc Dry batteries must not be recharged Used batteries must not be disposed of as household waste Lufkin Lpat310s Alignment A Scope G Battery charge indicator B View point H 5 8 tripod thread base C Scope mounting plate LC Display D Prism head J Control panel E Receiver diode for remote con
13. ssive angle out of its 5 range a warning signal will sound and the rotary head will stop turning The unit must then be placed on a more level surface Standby mode e The ON OFF button 37 on the Commander DA 50 can be used to switch the rotary laser to standby mode All preset values are retained highly recommended in digital slope mode e Note If the rotary laser is switched off directly by pressing the ON OFF button 34 on the unit all preset values will be deleted Tilt function e To protect the unit against drift due to external influences you must activate the tilt function To do this press the tilt button 33 see the ADS section about the anti drift system for more information Tilt 22 appears permanently on the LCD to indicate that the tilt function is active e Note The tilt function is not active in standby mode and the unit is not protected against drift Lufkin LDAL310S x Digital gradient function e Deviation from the horizontal plane can be set digitally for the X and Y axes The maximum slope in one plane is up to 7 999 and the sum of both axes may be up to 10 in 2 planes X axis and Y axis The values are displayed In 1 plane on the LCD and can be entered separately e To set the X axis press the X button 27 The first digit of the value assigned to the X axis will flash on the LCD Press the plus minus buttons 28 to select a positive 0 or negative value
14. trol K Battery compartment F Charger socket DC 9V Lufkin LDAL310S Included accessory SensoLite 310 Protection class IP 66 oh All round marking groove Laser beam sensors spotLite Marking LED Levelling vial Clamping screw for levelling staffs Universal mount Binding screw rear side Battery compartment rear side no O N O O A Q N Control panel 10 LC Displays front and rear side 11 Display measuring range selection Close up of detector 12 Detector above laser level 13 Precisely on laser level 14 Detector below laser level 15 Volume indicator 16 Low battery indicator 17 Detector mode Switch Precision range Free hand range 18 Volume adjustment Lufkin LDAL310S LC Display and control panel DualAxis Laser 19 i gt 2 N oe SLOPE CAL a 3 2534X ORO ps 19 Digital Slope function indicator 20 Digital slope adjustment X and Y axis indicator 21 Indicator of the laserbeam area 22 Tilt function indicator 23 Rotation speed indicator 24 auto man function indicator 25 Sensor Automatic indicator 26 Low battery indicator 27 Activate the slope adjustment of the X axis select data zone 28 Plus minus button for slope adjustment selection of the laserbeam area 29 Enter button 30 Set laserbeam area Commander DAL 50 31 Activate the slope adjustment of the Y axis select data zone 32 auto man function 33 Tilt function 34 ON OFF button DualAxis
Download Pdf Manuals
Related Search