UB-S09 User's Manual CAUTION:
Contents
1. UB SO9 User s Manual Introduction The UB S09 designed for EPSON TM printers and EPSON customer displays is a serial interface that has a maximum transmission speed of 115 2K bps bps bits per second with the TM printers or DM D series applicable to this product This manual provides instructions for operators of POS systems in which the UB S09 is installed so that the operators can use the UB S09 safely and correctly For information about installation and settings required see the UB S09 Developer s Guide Contact your EPSON representative or your place of purchase to get the UB S09 Developer s Guide Key to Symbols The symbols in this manual are identified by their level of importance as defined below Read the following carefully before handling the product CAUTION Observe cautions to avoid minor injury to yourself damage to your equipment or loss of data Q Note Notes have important information and useful tips on the operation of your equipment Caution Label The following caution label is visible near the modular connector customer display connector The label has the following meaning Use a modular connector specifically designed for a customer display for this product Do not connect this connector to an ordinary telephone line 401325800 Copyright 2000 by Seiko Epson Corporation Printed in Japan 2000 10 Part Names The following view shows the part names of th2. power supply to the printer EMC and Safety Standards Applied Product Name UB S09 Model Name M174A The following standards are also applied only to the units that are so labeled EMC is tested using the EPSON PS 170 power supply and TM series printer Europe CE marking North America EMI FCC ICES 003 Class A Japan EMC VCCI Class A Oceania EMC AS NZS 3548 Class B WARNING The connection of a non shielded interface cable to this board will invalidate the EMC standards of this device You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment CE Marking The printer conforms to the following Directives and Norms Directive 89 336 EEC EN 55022 Class B EN 55024 EN 61000 4 2 EN 61000 4 3 EN 61000 4 4 EN 61000 4 5 EN 61000 4 6 EN 61000 4 11 The printers in which this board is installed do not conform to the following Directive 90 384 EEC FCC Compliance Statement For American Users This equipment has been tested an found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment EN 45501 This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the i
3. e UB S09 serial interface connector customer display Caution connector label Connecting the Cables Before connecting any of the cables make sure that both the printer and the host computer are turned off Connecting the interface cable 1 Make sure both the printer and the host computer are turned off 2 Plug the cable connector securely into the UB S09 s interface connector 3 Tighten the screws on both sides of the connector Q Note If your interface connector has a grounding wire attach it to the printer using either of the screws that fasten the UB S09 to the printer 4 Attach the other end of the cable to the host computer Connecting the display module cable 1 Make sure both the printer and the host computer are turned off 2 Disconnect the power supply from the printer CAUTION You must disconnect the power supply because the electrical current is flowing in some parts of the printer circuit even when the power switch is turned off otherwise you may damage the UB SO9 and the printer 3 Plug the cable connector provided with the direct connection display module securely into the UB S09 s display module connector until it clicks CAUTION Do not connect this connector to an ordinary telephone line customer display connector Q Note Never connect customer display connectors to both the UB S09 and the TM printer at the same time 4 Connect the
4. nstruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense For Canadian Users This class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada
Download Pdf Manuals
Related Search