Installation and Operating Instructions
Contents
1. SOVEREIGN BBQS amp GRILLS AUSTRALIA iw mee fh A www sovereignbbgqs com Installation and Operating Instructions For Single Burner Outdoor BBQ Models Outback RV Explorer and Bushman RV Explorer IMPORTANT READ THIS DOCUMENT THOROUGHLY BEFORE USING YOUR SOVEREIGN RV EXPLORER BBQ IMPORTANT REMOVE ALL PACKING MATERIAL AND LITERATURE FROM YOUR BBQ BEFORE ASSEMBLY CONNECTION TO GAS AND USE Thank you and congratulations for choosing a quality Sovereign RV Explorer BBQ for all your cooking and entertainment needs This BBQ has been specifically designed for RV applications including Caravans Motorhomes and Camping It is manufactured from 430 Grade Stainless Steel well suited to the above applications By following these Installation and Operating Instructions for safe and easy operation you will enjoy many years of satisfying trouble free outdoor cooking IMPORTANT Your Sovereign RV BBQ is NOT suitable or designed for Marine use or salt air applications a Sovereign 316 Grade Stainless Steel appliance is available for these harsher applications DO NOT install this BBQ in such applications INSTALLATION Product Dimensions and Gas Connection Position Outback RV Explorer BBQ 600mm Long x 380mm Deep x 295mm High The gas connection is located on the right hand end of the BBQ and is 35mm from the rear and 80mm from the bottom of the BBQ Bushman RV Explorer BBQ 480mm Long x 350mm Deep x 240mm High The gas connection i2. Cont The injector size of the Outback RV Explorer BBQ is Propane 1 10mm and ULPG 0 85mm The injector size of the Bushman RV Explorer BBQ 1s Propane 0 95mm and ULPG 0 80mm For further information regarding the correct gas type and the gas consumption please refer to the data plate on the left hand end of your selected Sovereign BBQ model Gas Connection The gas inlet fitting on your chosen Sovereign BBQ is a 14 male B S P Parallel Inverted Flare fitting The correct connection to the gas inlet fitting is to be made with a 14 B S P Parallel Coned Swivel fitting After installation the gas technician should proceed to check that there are no gas leaks by brushing a soapy water solution over the connection points on both the gas supply source and your Sovereign BBQ do NOT use a naked flame Any leaks should appear as bubbles Retighten if necessary to ensure no gas leaks are present To make soapy water solution mix one part water and one part liquid detergent Apply the mixture with a paint brush to all connections and then turn the gas supply on at the supply point Any connections that are not properly sealed should appear as bubbles WARNING After installation and prior to ignition of the BBQ for the first time it is important that your gas technician checks the internal gas connections for leaks To check internal gas connections Outback and Bushman Models 1 Remove the burner refer to C
3. closely at the burner through the sight hole Once the flame failure valve has engaged after several seconds you can then release the control knob and adjust the BBQ to your desired temperature as per the low medium and high heat settings as detailed on the side of your BBQ adjacent the control knob Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com Lighting Cont 5 If ignition does not occur turn the control knob to the OFF position and wait minimum 60 seconds before trying again The below diagrams will assist you in lighting your selected Sovereign BBQ 1 Open BAS Lid 2 Of Position fy Piri Tht To Lat Oh Hed Ford Seo C3 Tum Gag On 4 Toe Ignite Optimum Cooking Temperatures WARNING always use the low temperature setting when cooking with the lid closed The BBQ will reach much greater temperatures with the lid closed Cooking time is also a lot quicker when cooking with the lid closed WARNING prolonged periods of excessive temperatures may cause damage to your BBQ The BBQ is designed to generate the required additional heat in adverse conditions such as wind and rain etc However generally a low setting is optimum for cooking in normal conditions WARNINGS 1 The outer shell of your BBQ will get hot during cooking 2 Do not touch your BBQ during cooking or after cooking while the applianc
4. area is completely open and i1 at least 30 of the remaining wall area is open and unrestricted In the case of balconies at least 20 of the total of the side back and front wall areas shall be and remain open and unrestricted Figure F1 Outdoor Area Example 1 Open side at least 25 of total wall area Figure F3 Outdoor Area Example 3 30 or more in total of the remaining wall Figure F4 Outdoor Area Example 4 area is open and unrestrictec Open side at least 25 of i mas total wall area i h 30 or more in total of the remaining wall 4 y area is open and unrestricted Figure F5 Outdoor Area Example 5 all aria Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com Gas Supply Information Your Sovereign BBQ is intended for connection to a reticulated gas supply eg a gas system which supplies other appliances including gas refrigerators and gas water heaters for example A reticulated gas supply system should be supplied installed and certified only by a qualified gas technician In the event that connecting your BBQ to a reticulated gas system is not preferred please liase with a qualified gas technician regarding suitable alternatives If connecting your BBQ to a gas cylinder using a gas hose and regulator only Class B or Class D gas hoses are suitable and the connect
5. ck cable with the ceramic pin end by lifting it out of its securing bracket Likewise unbolt the thermocouple copper tube with probe end adjacent the Piezo lead securing nut on the face side of the thermocouple locator bracket to allow the burner to side out the second rear nut at the back of the thermocouple locator bracket can be left as is 2 Lift the left end of the burner up while holding back the securing clip 3 Slide to the left off the gas control valve and out of the thermocouple locator and lift out Bushman Model In line Burner 1 Unclip the Piezo ignition system the black cable with the ceramic pin end by lifting it out of its securing bracket 2 Unscrew fixing on left hand side of burner 3 Lift the left side of the burner and slide to the left The below diagrams will assist you in removing the burner from your selected Sovereign BBQ 2 Lift Left Side Of Bumer 3 Slide Burner To Left Ancillary Service Information Your BBQ should be serviced at 12 month intervals or sooner as required by an authorised gas technician to ensure its ongoing safe operation Note that the burner flame should always burn blue with only a small amount of yellow at the peak If abnormal gas smells are present turn off all controls and the gas supply point then have your BBQ checked immediately by a qualified gas technician Do not modify this appliance in any way Sovereign BBQs amp Grills Australia Phone In
6. e is still hot 3 The use of protective gloves is recommended when cooking or handling parts of your BBQ that are hot or in use 4 Children should be supervised at all times around your BBQ 5 Long hair and loose clothing should be tied back in case of unexpected flare ups 6 Do not leave your BBQ unattended while in use 7 Do not place combustible materials near your BBQ 8 Do not spray aerosols in the vicinity of your BBQ while in operation 9 Your BBQ is not to be used as a space heater Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com To Turn Off 1 Turn the control knob to the OFF position 2 Always turn the gas supply off at the supply point as well CLEANING and MAINTENANCE BBQ Plate Do not clean your BBQ while hot Your BBQ plate can be easily removed using the handles on each side as per the below diagram BBQ shown with optional utensil tray Hot BBQ Plate Removal Recommended Cleaning Solutions and Appliances Clean the inside and outside of your BBQ with warm soapy water as required A stainless steel polish such as 3M stainless steel cleaner and polish should be used at regular intervals to protect and shine the outer casing Cleaning your BBQ after each use will diminish the burden of removing stubborn build ups or deposits NEVER use abrasive materials e g scouring pads t
7. ion fitting is to be compatible with the BBQ gas inlet fitting described under the Gas Connection section in these Installation and Operating Instructions Additionally ensure the regulator is the correct type as described in the Gas and Regulator Information section in these Installation and Operating Instructions In any instance the gas technician is to complete the installation and test that the BBQ operates correctly and safely They are to also confirm the installation is in accordance with these Installation and Operating Instructions and any governing regulations The gas technician must also instruct the user on the correct and safe operation of the BBQ General Precautions Do not obstruct any of the ventilation openings in your Sovereign BBQ body Should you need to disconnect the appliance from the gas supply point confirm that the BBQ is turned off and that there are no sources of ignition cigarettes open flame sparks etc nearby before proceeding Disconnect any hose from the gas supply point only and not from the appliance itself If the appliance is installed using a hose be sure to inspect the gas supply hose each time the BBQ is used and ensure it is free of any twisting or tension The hose should hang freely with no bends folds or kinks which could obstruct free flow of gas Apart from the connection point no part of the hose should touch any hot BBQ parts Inspect the hose before each and every use of the ap
8. just removed the brass thermocouple to replace the protective plate re test the connection point upon final completion of the re assembly where the thermocouple screws onto the gas control valve to ensure no leaks are present Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com The below diagrams will assist with testing your Sovereign BBQ for any leaks 4 c Remove Tighten amp Repke Outback RV Explorer model shown above U Shaped Burner Bushman RV Explorer model has a different burner being a single In line Burner If the correct installation or performance cannot be obtained contact Sovereign BBQs amp Grills Australia Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com Grill Kit Option It is possible to configure your nominated Sovereign RV Explorer BBQ with a Flat Grill plate cooking surface as shown below in lieu of the standard flat plate arrangement as packaged Should you elect to purchase this accessory option your Flat Grill Plate Kit will be supplied complete with a flame disperser The flame disperser is designed to sit over the burner on the grill half of the plate and below the BBQ plate itself see below diagram When the flame contacts the flame disperser the flame disperser distributes the fla
9. leaning and Maintenance section later in this document the burner removal process varies per Sovereign BBQ Model 2 Unscrew the 5 screws on the right hand side of the BBQ loosening the protective plate 3 Unscrew the brass thermocouple from the gas control valve to allow the protective plate to be fully removed Immediately refix the thermocouple after the protective plate is removed to complete the below outlined leak test Brush over all connections with a soapy water solution and then turn on the gas supply at the supply point Any leaks should appear as bubbles Re tighten internal gas connections on the control valve itself if necessary To retighten a pull off the black control knob b unscrew the two external screws beside the control valve shaft upon which the control knob is attached too and also undo the external nut on the threaded B S P gas inlet these fixings hold the control valve in place c remove the gas control valve and gas piping from the BBQ d retighten and replace Complete the process outlined in step 4 until no gas leaks are present and then proceed to re assemble the BBQ to its operating assembled status as follows 4 Unscrew the brass thermocouple to allow the protective plate to be reinstalled Refix the thermocouple after the protective plate is placed loosely in position 5 Tighten the five 5 screws that hold the protective plate in place and then re install the burner As you have
10. me and heat evenly over the grilling surface It is not recommended that you use your Flat Grill Plate BBQ without the disperser installed Grill Option As the above diagram shows the flame disperser clips in place on the left hand side of your nominated Sovereign BBQ with the recessed lowest part of the disperser inclusive of larger drain holes sitting directly over the fat tray as shown above Please ensure your disperser is installed in accordance with the above diagram USING YOUR SOVEREIGN BBQ Lighting 1 Open the BBQ lid on all occasions prior to lighting 2 The control knob should be in the OFF position 3 Turn the gas on at the supply point to the BBQ 4 To ignite push the control knob in and turn it to the left anti clockwise Repeat this action the piezo ignition will make a clicking sound each time you do this until the BBQ ignites and then continue to hold the control knob in for at least 3 seconds until the flame failure valve thermocouple has engaged depending upon various conditions it make take more than 3 seconds for the flame failure valve to engage on occasion To confirm ignition has occurred and after ignition upon release of the control knob that the flame failure valve has engaged a sight hole is provided beside the control valve The sight hole will allow you visually confirm the burner is alight please use appropriate caution when lighting including not looking directly into and or too
11. o clean the outside of your BBQ this will scratch the appliance A scouring pad may however be necessary to remove grease and build up on the BBQ Plate itself Do not use caustic cleaners NEVER use steel wool in addition to scratching it will also leave fragments that will rust Fat Tray and Flame Disperser WARNING Cleaning the Fat Tray and Flame Disperser A Flame Disperser is supplied only with the optional Flat Grill Plate Kit refer Grill Kit Option in these Installation and Operating Instructions after every use reduces the possibility of a fat fire in the fat tray caused by a flare up A flare up is when fat from food drops onto the hot flame disperser and ignites A small amount of fat will quickly burn out Removing excess fat from foods before cooking will reduce flare ups Be aware that some sausages can produce excessive fat during cooking The only recommended lining for the fat tray 1s aluminium foil Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com Burner Removal Burners should be removed periodically and cleaned with warm soapy water Ensure the burner is totally dry before reassembly which may take some time preferably dry your burner in the sun but exercise caution as it may become very hot to touch To remove the burner Outback Model U Shaped Burner 1 Unclip the Piezo ignition system the bla
12. pliance If the hose is damaged it must be replaced with an approved hose to AS NZS 1869 standards for use with LPG and meet the national standards for the country of use The length shall not exceed 1 5m Gas and Regulator Information WARNING Your Sovereign BBQ must be connected to a gas supply that has passed via an approved 2 75kpa regulator If you are in doubt as to wether or not your gas supply source is low pressure contact a qualified gas technician to ensure the gas supply source is suitable Please note your Sovereign BBQ is intended for use with either Propane Gas or ULPG Refer to the data label on the left hand end of your BBQ for the correct gas type to use with your BBQ your BBQ cannot be used with both gas types and is specifically configured for either Propane or ULPG applications Approved regulators for use with your Sovereign BBQ must have an outlet pressure of 2 75 kpa You must have an approved regulator in order for your BBQ to operate safely and efficiently Please consult your local gas technician for advice should you have any queries The gas consumption of the Outback RV Explorer BBQ is Propane 13 6Mj h and ULPG 9 5Myj h The gas consumption of the Bushman RV Explorer BBQ is Propane 11 0Mj h and ULPG 8 0M j h Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com Gas and Regulator Information
13. s located on the right hand end of the BBQ and is 23mm from the rear and 43mm from the bottom of the BBQ Choosing a Location This BBQ is for outdoor use only and should be placed in a well ventilated area Take care to ensure that it is not placed UNDER or ABOVE any combustible surfaces The sides of the BBQ should NEVER be closer than the following minimum recommended distances from combustible materials 100mm sides 200mm front and rear 50mm bottom 1200mm above Keep this BBQ away from flammable materials Installation of appliance must be in accordance with AS5601 2004 AG601 2002 requirements Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com Choosing a Location Cont This appliance shall only be used in an above ground open air situation with natural ventilation without stagnant areas where gas leakage and products of combustion are rapidly dispersed by wind and natural convection Any enclosure in which the appliance is used shall comply with one of the following An enclosure with walls on all sides but at least one permanent opening at ground level and no overhead cover Within a partial enclosure that includes an overhead cover and no more than two walls Within a partial enclosure that includes an overhead cover and no more than two walls the following shall apply i at least 25 of the total wall
14. tl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com WARNINGS 1 Your Sovereign BBQ is only to be used outdoors 2 Read the Installation and Operating Instructions carefully before using the appliance DISCLAIMER The Installation and Operating Instructions are provided on the understanding that Sovereign BBQs are not responsible for the results of any actions taken relying on the information in these Installation and Operating Instructions or for any error in or omission from these Installation and Operating Instructions Please also review the comprehensive Disclaimer documentation as included with this paperwork as use of the appliance infers your consent to this notification Sovereign BBQs amp Grills Australia Phone Intl 61 7 3382 0230 Fax Intl 61 7 3382 0087 Web www sovereignbbgs com Email sales sovereignbbqs com
Download Pdf Manuals
Related Search