Operating instructions for Washing machine W 5903 WPS
Contents
1. Drain Spin 32 Detergent 1 Use liquid detergent 2 Use powder detergent Miele special detergents Washing detergents which were specifically designed for certain programmes or items e g Miele CareCollection Only use proofing agents which are stated by the manufacturer as being suitable for use on membrane textiles as these consist of fluorochemical compounds Do not use proofing agents which contain paraffin Fill the detergent drawer amp with proofing agent All modern detergents produced for automatic front loading washing machines are suitable Use dispensing aids e g balls if these are supplied with the detergent Tablets are suitable for full loads but note that it may be impractical to reduce tablets for smaller loads Some tablets do not dissolve as rapidly as others and may not be suitable for programmes with short durations Do not use biological detergents on silk as the enzymes may damage the silk Instructions for use and recommended dosage amounts are given on the detergent packaging For programmes without Pre wash or Delay start liquid detergent can either be dispensed placing a ball shaped container commonly provided by the detergent manufacturer straight onto the laundry load or alternatively dispensed through the detergent dispenser drawer For programmes with Pre wash or Delay start where applicable an additional liquid detergent dispenser insert Material2. 30 t 4 Woollens E AAA Dark garments I 40 Denim Drain Spin Separate rinse Starch Spin button For selecting the spin speed or No spin The selected spin speed is illuminated in yellow Programme selector For selecting a wash programme and the appropriate temperature The programme selector can be turned clockwise or anti clockwise button For switching the washing machine on and off To save energy the washing machine will switch off automatically 15 minutes after programme end Anti crease or if no other function is selected after switching on Door button Opens the machine door Operating the washing machine Display The display shows the programme duration Time left display the programme sequence the selected Delay start the Settings Fault message and notes Display fascia The Start and Delay start buttons have a second function during initial operation and in the menu settings This secondary function is made visible with the display fascia gt OK Programme duration After the start of a programme the estimated programme duration will appear in the display in hours and minutes When Delay start is being used the programme duration will appear after the delay start time has elapsed During the first 8 minutes the machine measures how much water is being absorbed by the laundry The programme duration may be longer
3. Awash programme together with the Soak Extra option for heavily soiled laundry The Pre wash Extra option for laundry with large amounts of dirt e g dust sand When drying with a tumble dryer Selecting the highest possible spin speed for the wash programme will save energy when drying in a tumble dryer afterwards Brief instructions The headings numbered O show the operating sequence and can be used as brief instructions Sort the laundry m Empty all pockets Foreign objects e g nails coins paper clips etc can cause damage to garments and components in the machine m Badly soiled areas stains etc should be cleaned as soon as possible preferably whilst still fresh Spillages should be carefully dabbed off using a soft colourfast cloth Do not rub Badly soiled areas can be pre treated with liquid detergent stain removers etc first following the manufacturer s instructions With particularly stubborn stains ask your dry cleaner for advice How to wash correctly If you use a solvent based cleaning agent e g one containing benzene to pre treat a stain make sure that any plastic parts e g buttons are protected and that the cleaning agent is rinsed off before washing the garment in the machine ZN Do not use solvent based cleaning agents in this machine m Sort the laundry by colour and by care label Most garments have a textile care label in the col
4. Installation and connection FA LG 4 N m Using the spanner supplied turn the m Turn the right hand transit bar 90 left hand transit bar 90 then then m withdraw the transit bar m withdraw the transit bar 50 Installation and connection NTo avoid the risk of injury the holes for the transit bars must be covered after the transit bars have been removed m Secure the transit bars to the back of the washing machine Make sure that the upper hooks are above the retainers N The machine must not be moved m Fit the covers onto the two holes without the transit bars in place Store them as shown or keep them in a safe place for future use They must be re fitted if the machine is to be moved again e g when moving house Re fitting the transit bars Re fitting is carried out by reversing the procedure 51 Installation and connection Levelling the machine The machine must stand perfectly level on all four feet to ensure safe and proper operation Failure to level the machine can result in the machine banging in the spin cycle or walking across the floor during operation Screwing out and adjusting the feet The four adjustable screw feet are used to level the machine All four feet are m Use a spirit level to check the screwed in when the machine is machine is standing level delivered m Hold foot 1 securely with a pipe wrench Turn counter nut 2
5. Water consumption and energy usage are determined by the size of the load To make the most out of your machine load the maximum dry load for the programme you are using When smaller loads are washed in the Cottons programme the auto matic load recognition system will reduce the amount of water time and energy used This may mean that the time left shown in the display is adjusted during the course of the wash programme Use the Cottons 60 C programme rather than the Cottons 95 C programme This allows you to save between 35 45 energy This is sufficient for most soiling Use the Soak programme for more stubborn soiling Using the Cottons 40 C programme is recommended for a normally soiled load and is the programme used in energy water consumption tests to AS NZS 2040 Refer to consumption data Detergent consumption Do not exceed the amounts of detergent recommended by the manufacturer on the packaging Adjust the dosage to the degree of soiling of the laundry Reduce the amount of detergent with smaller loads approx less than the amount recommended can be used when washing a half load Choosing the correct Extra option Short Soak Pre wash Select Awash programme together with the Short Extra option for light to normal soiling where there are no obvious marks Awash programme without any Extra options for normal to heavy soiling with visible staining
6. etc and fluff Turn the impeller by hand to check that it rotates freely Any foreign object causing an obstruction should be removed m Put the drain filter back in place and secure Problem solving guide N Make sure the drain filter is securely tightened Otherwise there is a risk of water leakage during use To activate the ball valve and prevent a loss of washing detergent pour approx 2 litres of water through the detergent dispenser drawer after cleaning the drain filter Opening the drum door N Always make sure that the drum is stationary before reaching into the machine to remove laundry Reaching into a moving drum is extremely dangerous m Pull the emergency release downwards see illustration The drum door will open 45 After sales service In the event of any faults which you cannot remedy yourself please contact your Miele Chartered Agent or Miele see back cover for contact details When contacting Miele please quote the model and serial number of your appliance both of which are shown on the data plate visible at the top inside the door above the porthole glass when the door is open 46 Future updates PC The indicator light marked PC allows a service technician to update your machine in future years If for example new programmes are developed or new fabrics are introduced a Miele service technician will be able to modify existing
7. programme cycles accordingly Miele will provide information when such developments become available Appliance warranty The appliance has a manufacturer s warranty of 2 years See the warranty card supplied with the machine for further details Optional accessories Optional accessories for these washing machines are available from Miele Please note that telephone calls may be monitored and recorded to improve our service Front view E am Inlet hoses with Waterproof system for cold water and hot water connection Electrical connection 3 Flexible drain hose with detachable swivel elbow Fascia panel with controls Installation and connection Detergent dispenser drawer 2 Drum door 40 Flap for fluff filter drain pump and emergency release Handle recesses for moving the machine 42 Four height adjustable screw feet 47 Installation and connection Rear view lll Z G Protruding lid for holding when moving the machine 2 Electrical connection 3 Inlet hoses with Waterproof system for cold water 4 Inlet hoses with Waterproof system for hot water 5 Drain hose 48 INN m SS I mi m Y SS E sss ES Zn Al 7 Up SS SS NS 6 Transport brackets for inlet and drain hoses Transit bar covers 8 Transport brackets for inlet and drain hose and restraining
8. 2 20 59 2h 19 min 60 C 7 5 kg 1 05 55 2 h 09 min 60 C 3 5 kg 0 64 45 40001 7 5 kg 0 56 62 2 h 24 min 40 C 35 KG 0 45 45 59 min Minimum iron 40 C 3 5 kg 0 50 50 1 h 05 min Delicates 30 C 2 0 kg 0 38 69 59 min Darks and denim 40 C 3 0 kg 0 60 52 1h 12 min Woollens 4 30 C 2 0 kg 0 23 39 39 min Note for test institutes 1 AS NZS 2040 1 amp AS NZS 2040 2 Consumption data can vary from the nominal values given depending on water pressure water hardness water inlet temperature room temperature type and volume of load fluctuations in the electricity supply and any additional options selected 61 Settings menu The programmable functions are used to alter the machine s electronics to suit changing requirements Programmable functions can be altered at any time To open the Settings menu m Close the washing machine m Set the programme selector to Finish m Place the display fascia onto the panel m Switch on the washing machine m Press both buttons and OK simultaneously until the following appears in the display Settings Continue OK You are now in the Settings menu Selecting settings m Press the button until the desired setting appears in the display m Press the OK button to select the setting Select option m Press the button until the desired option appears in the display m Press the OK button to select the option A tick Y will appear beside the option to
9. The tap should be fitted by a qualified plumber N The connection points are subject to mains water pressure Turn on the taps slowly and check for leaks Correct the position of the washer and union if appropriate Maintenance and care Only use a Miele Waterproof system hose should you need a replacement In order to protect the water inlet valve the dirt filter in the water inlet valve connection must not be removed Extension hose A 1 5 metre long metal extension hose is available from Miele as an optional extra This hose is tested to withstand pressures of up to 14000 kPa and can be used as a flexible extension to the water supply 55 Installation and connection The washing machine is programmed Useful hints when connecting to the hot on cold water at the time of delivery To and cold water supply run the machine with hot water it needs to be reprogrammed This is described under section Settings menu The maximum temperature at the tap must not exceed 60 C The ideal temperature is 55 C The washing machine must always When connected to the hot and be connected to the mains water cold water supply after some time supply inlet hose with blue dots the washing machine will switch over to the mains cold water supply if no Cold water connection mains water hot water is being supplied supply However this can lead to a poor The inlet hose with blue dots is used for o tasu m
10. a ess LOSE Gee CeCe a 62 rie naib aoe er hee Ga dare A 62 Gentle ACUON Sos ou 4444006 oe beet Reed eked ee heat nds Soke eee aes 63 OA dss anata ee A Bir ka Ob ae Rone bead abe eee aes Sas 63 NCTE to ci ann rer are So ach ES de eee CO oe Bee es 63 Longer pre wash sopresa tapas wee a e paa Re eee wee ene a 63 SUS COCONINO ana 8444 306 4e dda ous Ad Re Ste bade nies aeons 64 BET gic a et bh wie cee ees ee Meek A eee ohne ae Da eae hee wake e 64 e cute ace O ee ahd eRe OR rer 65 Keypad tone es kenne au eee ee haw ee Med deta ee Obs ew eee aa eo 66 Display DIGMNSSS e s 0 24 Led hao Weds san a da fo 604 aaa bods ha 66 Display contrast asas ard cud O een eae eRe Ewe 66 TEXCDUQHINESS ie coe ceo redada EAS peer ek eed 66 standby display 400s ac ot Su ak kae IN eat ka EN RER 67 MEMO emere Eby een Oe DEG AS OEE GEG S ee 67 PRAMS SE a ad be A ed RE EHEN ee hese Eredar 67 Ve FAA sc ne wae suede ds AR nak Rare bene ee 68 Optionalaccessories ur eee ws oe Ge Fhe ee ea 69 Cale COCOA unsere kee SAG RRS A eM Eee Leese aa es ea 69 Warning and Safety instructions This washing machine conforms to current safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the washing machine please read these instructions carefully before using it for the first time They contain important information on its installation safety use and maintenance Keep these instruc
11. additional rinse is introduced Spinning To omit rinse and interim spin and the final spin No spin m Select the setting No spin via the Spin button The water will drain away and the machine will go straight into the anti crease stage An additional rinse is introduced for the programmes Cottons and Minimum iron in this setting m Press the Door button and take out the wet garments or m Turn the programme selector to Drain Spin m Take note of the set spin speed m Press the Start button 23 Delay start Delay start allows you to delay the start of a programme from 15 minutes up to a maximum of 23 hours and 45 minutes This allows you to make use of night time economy electricity rates for example Delaying the start of a programme m Select the programme you want and then press the Delay start button The display shows Start in 0 15 h m Each press of the Delay start button extends the delay time by 15 minutes If the Delay start button is held in the time is automatically set to 23 hours and 45 minutes Correct entered delay start time m Turn the programme selector to Finish m Select the required wash programme again m Press the Delay start button and enter the time again 24 Start delay start time m Press the Start button The selected time will count down in the display and the wash programme will be started Delete delay start time You can delete the delay
12. appliance to prevent misuse Contents Caring for the environment 2 Warning and Safety instructions 0 000 000 cee 6 Operating the washing machine 00 00 eee 10 CONO Dane Sueras ad AAA eee eae eae 10 DIS norris trad asada rada esa 11 Before using for the first time 20 2 00 eee 12 Washing environmentally and economically 14 Energy and WalerCOnSuMPUON ve scada cae deci we does 14 Detergent consu QUOA seser era Den A a 14 How to wash CONOCI 6 estopa traes 15 Brief INStrUCtIONS ira estao ee dhe een RSS ow er old a ob Bae As 15 Programme selection 0000 cette 20 Extra OPHONS scr ro Disidente biest sk A hohe eee Ke 22 SPIRHING e osasu risa eg ai edain a ei i aiei see 23 Delay Stat 2 na dn ped cused sirbe Rs a e A E E ai 24 Programme chart 00 0 020 eee 25 Garment care label symbols 0 000000 c eee eee 27 Programme Sequence 28 Changing the programme sequence o 30 Cancelling a Programme ua 6a eee bd Koes ghee dee hen SS aE ae bE RS 30 Interr ping a PIOgrammeE urn 30 NOS ae eee ed ee Se ee ee Be ha BE pee A Ee ask 30 Adding or removing laundry after a programme has started 31 Delergent oec raris riris tes sa rada desire do ine che 32 Ihecorect detergent a4 ge oa we rra ait wire dope Ow san ea aa da e a 32 Water sotene sos reade ite a arte e a nA a Ea ad EAS 34 Wash
13. be hot when washing at very high temperatures Do not let children touch it Warning and Safety instructions Technical safety gt Before setting up the washing machine check it for any externally visible damage Do not install or use a damaged washing machine gt Before connecting the washing machine ensure that the connection data on the data plate voltage and rated load match the mains electricity supply If in any doubt consult a qualified electrician gt The electrical safety of this washing machine can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock gt Do not connect the washing machine to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating gt Faulty components must only be replaced by genuine Miele original spare parts Only when these parts are fitted can the safety standards of the machine be guaranteed gt Unauthorised repairs could result in unforeseen dangers for the user for wh
14. clips for transit bars Installation surface A concrete floor is the most suitable installation surface for a washing machine being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface Please note m The machine must be level and securely positioned m To avoid vibrations during spinning the machine should not be installed on soft floor coverings If installing on a wooden joist floor m We recommend a plywood base at least 59x52x3 cm The base should span several joists and be bolted to the joists and not only to the floorboards Check for the presence of pipes and cables first If possible install the machine in a corner as this is usually the most stable part of the floor AN the machine is installed on a raised plinth it has to be secured against slippage during spinning using retaining clips available from Miele Installation and connection Installing the washing machine To manoeuvre the machine out of its packing case to its installation site hold it by the edge of the lid where it protrudes to the rear of the washing machine as well as by the handle recesses at the front N Ensure that the machine feet and the floor are dry to prevent the machine from slipping during the spin cycle Removing the transit bars m To remove the left and right covers 1 Pull off the transit bar covers and 2 use a screwdriver to prise out the covers 49
15. estimated programme duration will appear in the display O Selecting Extra options if required Gus Soak Water plus gt Pre wash gt m Press the button for the programme you wish to run The Extra option will be illuminated Not all the Extra options are suitable for use with every programme You can only select Extra options which are compatible with the basic programme being used See Extra options for more information How to wash correctly O Selecting Spin speed if required You can reduce the final spin speed 1400 1200 900 400 Without spin gt m Press the Spin button until the required spin speed is highlighted in yellow See Spin for more information O Selecting Delay start if required The start of the programme can be delayed from 15 minutes up to a maximum of 23 hours and 45 minutes This allows you to make use of night time economy electricity rates for example See Delay start for more information How to wash correctly O Add detergent It is important to dispense the correct amount because too little detergent results in laundry not getting properly clean and with time it may become grey and hard to the touch greasy particles clinging to the laundry limescale deposits on the heater elements too much detergent results in excessive foam which causes a low level of agitation and poor wash rinse and spin
16. noises occur at the end of a pump sequence as a normal part of the operation Large amounts of detergent residue remain in the detergent dispenser drawer The water pressure is too low Clean the filter in the water inlet Select Water plus Powder detergent used with water softeners can be sticky Add washing powder and then add the water softener Fabric conditioner is not completely dispensed or too much water remains in the amp compartment The siphon tube is not correctly positioned or is clogged up Clean the siphon see Cleaning and care Cleaning the detergent dispenser drawer The display is ina different language A different language has been selected in Settings Language P Set the language you want The flag symbol will guide you When laundry is dry it feels hard to the touch Too vigorous wash action Programme in gentle action and more water Not enough detergent used Increase detergent dose to prevent limescale build up in laundry No fabric conditioner used Use fabric conditioner in last rinse Power cut Once power has been restored to the appliance push the D button to continue the programme 41 Problem solving guide An unsatisfactory wash result Problem Possible cause Remedy Liquid detergent does not give the required result Liquid detergents do not contain bleachi
17. of one hour A tick Y will appear beside the soaking time to show that it has been set Settings menu Water plus This programmable function is used to select the water intake setting for the Water plus Extra option There are three different options Water the machine is delivered with this option selected as standard The water level is increased in the wash and rinse stages Extra rinse An extra rinse is introduced Water amp Extra rinse The water intake is increased in the wash and rinse stages and an extra rinse is carried out A tick Y will appear beside the option to show that it has been set Longer pre wash The pre wash for the Cottons programme can be extended by 6 9 or 12 minutes The default setting for the pre wash is 25 minutes If you require a longer pre wash this can be extended A tick Y will appear beside the option to show that it has been set 63 Settings menu Suds cooling When this is activated additional water flows into the drum at the end of the main wash to cool the suds down Hot suds can damage plastic drainage pipes Suds cooling takes place when temperatures of 95 C and 75 C are selected Suds cooling should be activated to prevent the danger of scalding if the drain hose is hooked over the edge of a sink or basin where the drainage pipes do not comply with DIN 1986 The machine is delivered with Suds cooling dea
18. results higher water consumption an additional rinse cycle will automatically switch on a burden to the environment 18 m Pull out the detergent drawer and place detergent in the compartments as follows Ly Detergent for the pre wash divide the total recommended amount as follows add 1 4 to compartment LU and 7 3 to compartment UV ul Detergent for the main wash B Fabric conditioner or liquid starch m Close the detergent drawer See Detergent for further information How to wash correctly O Start the programme Check that all items have been removed from the drum Left items If a delay start time has been set this might shrink in the next wash or will count down in the display At the discolour other items end of the delay start time or immedi ately after the programme has started if no delay start time has been selected the estimated programme duration will appear in the display During the first 8 minutes the machine measures how much water is being absorbed by the laundry The programme duration may be longer or shorter depending on this absorbency rate m Press the Start button The programme sequence is also shown in the display The programme sequence display shows the stage the m Check the folds in the door seal for programme has reached any small articles e g buttons which igh here Remove the laundry when the oO Aa programme has finished m Turn
19. show that it has been set 62 Changing values Some settings have no options but the set value can be changed Each press of the button increases the set value Once the maximum setting has been reached the value jumps at the next press of the button to the minimum setting The set value is confirmed by pressing the OK button To leave selected setting In settings with options you can find the point back To close the Settings menu m Switch off the washing machine Language F The display can be set to appear in one of several different languages You can change the language for the display via the Language sub menu The flag after the word Language acts as a guide if a language you do not understand has already been set The set language will be marked with a tick V Gentle action Activating gentle action reduces the drum action and is suitable for washing slightly soiled items more gently Gentle action can be activated for the Cottons and the Minimum iron programmes The machine is delivered with the Gentle action setting deactivated Atick Y will appear beside the option to show that it has been set Soak You can set a soaking time with the Soak button from between 30 minutes and two hours in 30 minutes steps The selected soaking time will precede the actual wash programme by selecting the extra function Soak The Soak button is delivered with a soaking time
20. siphon 1 Remove the siphon from compartment and rinse under m Use a bottle brush to remove warm running water Clean the detergent residues and limescale siphon tube in the same way from the jets inside the detergent dispenser drawer housing 2 Replace the siphon If starching frequently thoroughly clean the siphon and siphon tube regularly A build up of starch will cause them to get clogged 37 Cleaning and care Cleaning the filter in the water inlet The washing machine has a filter to protect the water inlet valve The accessible filter in the union in the open end of the inlet hose should be checked every six months or more often if there are frequent interruptions to the external water supply 38 m First turn off the tap m Unscrew the threaded union connecting the free end of the inlet hose to the tap m Remove the rubber seal 1 from the recess m Using pointed pliers take hold of the plastic filter bar 2 and remove m Clean the plastic filter m Put the filter and seal back in the reverse order and reconnect the hose Turn on the tap and check the connection is watertight If water drips out tighten the connection Never forget to put the filter back in place after cleaning What to do if Problem solving guide With the aid of the following guide minor problems can be easily corrected without contacting Miele Please note that a call out charge will be applied for
21. start time and start the selected programme straight away m Press the Delay start button Programme chart Cottons 95 C 60 C 40 C 30 C Max load 7 5 kg Item Cottons linens or cotton mixed fabrics e g table linen towelling underwear T shirts etc Note for test institutes Short programme 3 5 kg load and Short Extra option Minimum iron 60 C 40 C 30 C Max load 3 5 kg Item Synthetics mixed fibres and easy care cottons Note Reduce the spin speed for fabrics which crease easily Delicates 40 C 30 C Max load 2 5 kg Item For delicate garments made of synthetic fibres mixed fibres and rayon Curtains including net curtains specified as machine washable by the manufacturer Notes Dust in curtains usually makes using a programme with a pre wash advisable For items which crease easily deselect the spin Dark garments 40 C Max load 3 0 kg Item Black and dark garments made from cotton mixed fibres and denim Notes Wash inside out Denim often contains excess dye and will run during the first few washes Wash light and dark coloured items separately 25 Programme chart Woollens 4 30 C Max load 2 0 kg Item Machine washable or hand washable wool or wool blend fabrics If the care label does not specify atemperature wash using the cold setting Note Reduce the spin speed for fabrics which crease easily Separate rinse St
22. the next section The door was not correctly engaged Press hard against the lock side of the drum door and then press the Door button There is still water in the drum and the machine is unable to drain Clean the drain filter and drain pump as described in the next section For safety reasons the drum door cannot be opened if the suds temperature is higher than 55 C 43 Problem solving guide Opening the drum door in the event of a blocked drain outlet and or power failure m Switch the washing machine off There is a filter flap opener behind the detergent drawer fascia panel m Use it to open the access flap 44 Blocked drain outlet If the drain outlet is clogged more water will be retained in the machine up to 25 litres N Caution If laundry has been washed at a high temperature water draining out of the machine will still be hot Danger of scalding Procedure for draining the machine m Place a suitable container under the access flap When draining water from the machine do not unscrew the drain filter completely or take it right out m Turn the drain filter lid round until water runs out To interrupt the flow of water m Tighten the drain filter back up again Once the flow of water ceases m Remove the drain filter completely m Clean the drain filter thoroughly m Remove any foreign objects e g buttons coins
23. too high Pin ieee The water inlet is Check whether ater intake Open stopcack blocked or the tap is opened wide restricted enough the inlet hose is kinked M Waterproof activated Close stopcock The water protection system has reacted Call Miele A Technical fault Call the Service Department There is a fault Start the programme again If the fault message appears again contact Miele The following will flash in the display Anti crease alternately with Chk detergent Excessive foam has built up during washing Use less detergent next time and follow the manufacturer s instructions on dosage given on the packaging O To switch off the fault message Switch the washing machine off with button 40 Problem solving guide General problems Problem Possible cause Remedy The machine shakes during the spin cycle The machine feet are not level Level the machine see Installation The laundry has not been spun properly and is still wet The machine detected an imbalance during the final spin and reduced the spin speed automatically Include both large and small items in the load as this will give better distribution The laundry has not been spun satisfactorily The spin speed selected was too low Select a higher spin speed next time The pump makes strange noises This is not a fault These
24. AAA N A for Washing machine W 5903 WPS To avoid the risk of accidents en AU NZ or damage to the machine it is essential to read these instructions before it is installed and used for the first time M Nr 07 647 500 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Rather than just throwing these materials away please ensure they are offered for recycling Disposal of your old appliance or machine Electrical and electronic appliances machines often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance or machine Therefore please do not dispose of your old machine or appliance with your household waste Please dispose of it at your local community waste collection recycling centre and ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person The plug must be rendered useless and the cable cut off directly behind the
25. again using the spanner supplied until it sits firmly up against the housing ZN AI four counternuts must be firmly up against the housing Please also check this for the feet which did not need adjustment Otherwise there is the danger of the machine moving about m Using the spanner supplied turn counter nut 2 in a clockwise direction Then turn counter nut 2 together with foot 1 to unscrew 52 Building under a continuous worktop in a kitchen run A special building under conversion kit is required The machine lid must be replaced by a cover plate To ensure electrical safety the cover plate must be fitted N B If you wish to push your machine under a worktop and there is space to do this without removing the lid the conversion kit is not necessary Otherwise the conversion kit is essential For installation under a work surface 900 910 mm from the floor a raising kit is required Connections for electricity water and drainage should be installed in such a way that they remain accessible when the machine is in place Fitting instructions are supplied with the conversion kit All parts marked are available from Miele The fitting of cover plates and stacking kits must only be undertaken by qualified and competent persons in accordance with the instructions supplied with the kit Installation and connection Washer and Dryer stack A Miele tumble dryer can be stacked
26. ains water connection The conditions for connection are Hetwatereonneation described on the following pages The inlet hose with red dots is used for This appliance incorporates connection to the hot water supply backflow protection complying with ATS 5200 101 No further backflow protection required for connection to the water supply 56 Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre The drain hose must not be kinked as this restricts drainage The swivel elbow at the end of the hose can be turned in either direction or can be detached if required with a sharp twist and pull If required the drain hose can be extended to a length of 5 m The necessary parts can be purchased from Miele For a delivery head more than 1 m up to a max of 1 8 m a second duo drain pump is available with the corresponding kit from Miele Drain hose connection 1 Direct into a sink or basin Please note the following Hook the hose over the edge and secure Make sure that the water can drain away freely without hindrance Otherwise there is a risk of water overflowing or of some of the drained water being sucked back into the machine 2 Connected securely to a plastic drain pipe with a rubber nipple There is no need to use a non return valve 3 Connected securely to a standpipe 4 Connected securely to a floor gully Installation and connec
27. ar UY ers e ae mr an ER ne Be A Eee ae 48 INstallalons fase ass an ner nr ROLE aS a ed heed Mors Ok er 49 Installing the washing machine u 2c ccna eae eee eee ee ee ee eas 49 Removmg INES rane DAS ca escasa dende ad die 49 Re fitting the transit Bars 24 224 Hu an aaa aa an en ea ee ee 51 Esto Ines MAC ING Stones e aam atg he eee he tee eee here ceo 52 Screwing out and adjusting the feet aa eee 52 Building under a continuous worktop in akitchenrun 00 53 Washer amd Diversiath s 4s can tac g oe RARER AGRA ea de eG Oe oes 53 The Miele Waterproof system 0 0 54 Connection to the water SUD DIY sa wur a Kar ee Pek aude ad 55 Cold water connection mains water supply saoasaoa aaiae 56 Hot water CONMECION seast ereas ea ica Oe Radin cid a 56 Connection to the drainage SyStemM naana aaa 57 Electrical connection ee Kran dad rs ds dana pita 58 Contents Technical data sucurs000s 00H cc 59 Consumption data 66564046044 caro dera CREED OO dE een 60 Consumption data for the nominated energy labelling programme according to AS NZS 2040 1 amp AS NZS 2040 2 Standard 60 Notes for test institutes niet che src Chie edu g eher baw eeeeged ae 60 Settings MENU usw ose 54s eed dee 44 erario EOE ERLE 62 To open the Settings Menu testar nos wader eee wie needs 62 Selecting settings un urn ee ba lee eee naar ee he 62 To Close Ne Settings ME ces saci Koti Noose
28. arch Max load 7 5 kg Item For rinsing hand washed items Table cloths napkins and overalls that require starching Notes Reduce the spin speed for items which crease easily The laundry should be washed but not treated with fabric conditioner Drain Spin Notes Drain only Set spin speed to No spin Make sure you select the appropriate spin speed 26 Garment care label symbols Washing Drying The figure quoted in the tub is the The number of dots indicates the maximum temperature the garment drying temperature can be washed at Normal temperature No bar under the symbol Low temperature normal agitation a D Els o not tumble dr One bar under the symbol 2 reduced agitation E Ironing Two bars under the symbol es much reduced agitation The number of dots indicates the e ironing temperature Hand wash If no temperature E is specified use the lowest ZA approx 200 C temperature or cold ZA approx 150 C AXI Do not wash FA approx 110 C ZX Donot iron Examples of programme selection Professional cleaning Programme Care label E Dry clean only The letters Cottons _ indicate the type of cleaning Minimu iron agent required Daliesies W Professional Wet Clean only Dark ES Do not dry clean SEEN Bleaching Woollens Wy U A Any oxidising bleaching agent can be u
29. ase of the appliance A float switches off the water inlet valves preventing water flowing into the machine and water in the suds container is pumped away Overflow protection This prevents the washing machine taking in too much water If the water level exceeds a certain level the drain pump switches on and pumps the water away 3 Drain hose The drain hose is protected by a ventilation system which prevents the washing machine from being emptied completely Connection to the water supply N The plastic casing of the safety valve contains electrical components The Waterproof system must only be connected to its own tap It must not be connected to mixer taps or similar and must not be fitted in areas where there is the risk of water or other liquids reaching it A flexible metal extension hose available from Miele as an optional extra should be used if necessary Do not dip into any liquid The protective sleeve of the hose must not be damaged or kinked Installation and connection The machine should be connected to a mains water supply in accordance with local and national safety regulations Connection to a household water softener is not recommended The machine is designed to operate with a flow pressure of between 100 and 1000 kPa If it is higher than 1000 kPa it is essential to fit a reducer valve Connection to the mains water supply should incorporate a mains tap with thread
30. ctivated Lock code The code prevents your machine being used without your knowledge When the code has been activated you have to enter a code after switching the washing machine on Otherwise the washing machine cannot be operated 64 To activate the code Lock code Continue OK m Press the OK button m You are asked to enter a code The code is 125 and cannot be altered To enter the lock code Lock code T m Enter the first number with the gt button Confirm by pressing the OK button Now enter the second number m Repeat the process until all three numbers have been entered Confirm code 125 m Confirm the lock code by pressing the OK button or if you want to correct it press the button The following will appear in the display D Lock code activated Entry OK Once the machine is switched off it can only be used again if the code is entered To use the washing machine when the code is activated When the machine is switched on again the display will request the lock code m Enter code 125 as described above and confirm the entry The following will appear in the display fe Readw ES Entry OK The washing machine is now unlocked and ready for use To deactivate the code Proceed as for activating the lock code The following will appear in the display Lock code deactivated Entry OK Settings menu Buzzer When the buzzer functio
31. d This also activates the ball valve The ball valve prevents detergent escaping from the suds container into the sump during a wash programme thus making maximum use of the detergent 12 Before using for the first time 2 Language settings display You will be asked to select the language you require for the display It is possible to change the language at any time via the Settings menu Sprache d Ok m The required language can be selected by pressing the button Confirm with OK 3 Reminder to remove transport struts To avoid the risk of damage the transport struts must be removed before the machine is used for the first time See Installation and connection for instructions on how to do this Remove transport i bars OF m After removing the transport struts if this has not already been done by your fitter press the OK button m Remove the display fascia 4 Running your first programme Your machine is now ready for the first programme to be run Select Programme m Turn the programme selector to Cottons 60 C Duration 2 09 h Start flashes green m Press the Start button The washing machine will now run a complete wash programme Anti crease Finished m Turn the programme selector to Finish m Switch off the washing machine The machine is now ready for use Washing environmentally and economically Energy and water consumption
32. e laundry from the washing machine once the drum has stopped turning Reaching into a moving drum is extremely dangerous and could result in injury Accessories gt Accessory parts may only be fitted when expressly approved by Miele If other parts are used warranty performance and product liability claims will be invalidated Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Operating the washing machine Control panel Start Short Go n Soak 900 400 Water plus Delay start Pre wash 00 4 Display See the next page for more information 2 PC Optical interface This is used by service technicians to run diagnostic checks on your machine and can also be used to update programming data in the future Start button For starting the programme selected The green backlight of the word Start flashes if a programme can be started and stays lit up if a programme has already been started 4 Delay start button For selecting delay start If a delayed start has been selected the words Delay start will be illuminated in yellow 5 Extra option buttons Various Extra options can be added to the washing programmes If an Extra option has been selected the relevant Extra options will be illuminated in yellow Without spin Minimum iron Cottons 60 Finish 95 Delicates 40 30
33. has started Changing the programme sequence Adding or removing laundry after a programme has started m Press the Door button to open the drum door m Add or remove items m Close the drum door The programme will continue automatically Please note Once a programme has started the machine cannot recognise any adjustment to the load For this reason if laundry is added or removed after the start of a programme the machine will always complete the programme cycle assuming a full load This can increase the programme running time shown in the display The door cannot be opened if the suds temperature is above 55 C the water is above a certain level the programme has reached the Spin stage If you press the Door button when the above conditions are present the following will appear in the display Sea Door locked 31 Detergent The correct detergent All modern detergents produced for automatic front loading washing machines are suitable Refer to the manufacturer s label on the packaging to get information on the use and the dosage rinse Starch Detergent Detergent Detergent Special Proofing Fabric for for for detergent agent softener universal coloured delicates fabrics fabrics Cottons X X x Minimum iron X X X Delicates X X X X Darks and denim X X X X Woollens W x X Separate X X
34. ich Miele cannot accept liability Repairs should only be undertaken by a Miele approved service technician Ensure current is not supplied to the machine until after maintenance or repair work has been carried out gt If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger gt In the event of a fault or for cleaning purposes the washing machine is only completely isolated from the electricity supply when itis switched off at the wall socket and the plug is withdrawn or itis switched off at the mains or the mains fuse is withdrawn or the screw out fuse is removed in countries where this is applicable gt The Miele Water protection system protects from water damage provided the following conditions have been met the machine is correctly plumbed in and connected to the electricity supply if a fault has been identified the machine must be examined by a competent person before further use and repaired if necessary gt In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the machine and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the machine warranty Warning and Safety instructions gt This washing machine must not be installed and operated in mobile i
35. ing with several COMPONEN S s2 056cdsee eee nhda wea ea e 34 Fabric conditioners and liquid starch cra rd a is een 35 Automatic dispensing of fabric conditioner or liquid starch to laundry al ne end Ola programines vx sed e ei A eu 35 Adding fabric conditioner or starch separately nnana aaa 35 Colour run and dye removers dyeS n nananana 35 Contents Cleaning and Care 0 0 0 0 cee 36 External casing ana fascia panel censeas stacker dee keen dades oia 36 Extra Clas ssa ot et be A wees Dae ee 36 Cleaning the detergent dispenser drawer 0 0 0 ccc eee 36 Cleaning the filter in the water inlet 0 0 ce eee 38 Problem solving guide 00 e a 39 A ee eee ee wee 39 The programme does not start 0 0 eee 39 Fault messages in the display u eu Haare A Pe Se ESE eS 40 General problemS coccion aan a hada EGER ORES SE hen aS 41 An unsatisfactory wash result scores a e di le 4 42 The drum door does not open when you press the Door button 43 Opening the drum door in the event of a blocked drain outlet and or power FANGS se acces ont Oo ob cto a roda 44 After sales Service o ee eee 46 F RS pdat s PO a cc ede d mda bea asa e weak WAR E ms 46 A WANN tows staal at koa kt eRe eee ee a ed hoe BR EES ea 46 Optional accessories ocx via a cde a di a A 46 Installation and connection 0000 000000000 eee 47 POON VIEW A eee Oho tee KOS 47 Re
36. ion Degree of soiling Extra options 21 Extra options Short For light to nomal soiling with no visible staining The duration of the main wash is reduced Soak For heavily soiled and stained items with protein stains e g blood fats and oils cocoa The soaking time can be programmed to between 30 minutes and two hours in 30 minute steps The factory default setting is one hour See Soak in the Settings chapter Water plus The water level in the main wash and the rinses will be increased ifthe Water plus option is selected However you can select other settings for Water plus These are described in Settings menu Pre wash For laundry with large amounts of dirt e g dust sand 22 Selectable Extra options TU Os Cottons X X Minimum iron X X Delicates X X Dark garments X X Woollens tw Final spin speed Programme rpm Cottons 1400 Minimum iron 1200 Delicates 400 Darks and denim 1200 Woollens W 1200 Separate rinse Starch 1400 Drain Spin 1400 You can reduce the final spin speed However you cannot select a final spin speed higher than that shown in the chart above Rinse and interim spin There is a spin after the main wash and between the rinses A reduction in the final spin speed will also reduce the interim spin speed For the programme Cottons with a spin speed of 400rpm an
37. lar or side seam Dark textiles often contain excess dye and should be washed separately several times first Always wash whites and coloureds separately Curtains Remove lead weights first or place in a laundry bag Underwiring and collar stiffeners Any loose wiring in bras shirt collar stiffeners etc should be removed or sewn in Close any zips fasten hooks and eyes etc before washing Fasten duvet covers etc to prevent small items from being rolled up inside them Do not wash any items in this machine which are specified by the manufacturer as not washable on the care label IX symbol 15 How to wash correctly O Switch on the washing machine m Press the button Select Programme Load the drum m Press the Door button to open the drum door m Unfold the laundry and load loosely in the drum Mixing both large and small items gives better wash results and also helps distribute the load evenly during spinning The most efficient use of energy and water is achieved when a full load is washed However do not overload as this causes creases and reduces cleaning efficiency Make sure that no garments are caught between the drum door and seal m Shut the door with a gentle swing O Select a programme Minimum iron 60 Finish 95 40 Delicates Separate rinse Starch m Turn the programme selector to the required programme Duration 1 45 h The
38. lay To save energy the display and the lights will go out and the indicator light for the Start button will start flashing slowly The display will always go out if a programme is not selected within 10 minutes of the machine being switched on 10 minutes after the end of a programme Pressing one of the buttons switches the display and the lights back on again You can also choose whether the display and the lights remain on or off during the course of a programme On The standby function is switched on The display and the lights will be switched off 10 minutes after the start of the programme Not in current programme the machine is delivered with this option selected as standard The standby function is switched off The display and the lights remain switched on during the course of the programme Settings menu Memory If an Extra option has been selected for aprogramme or the recommended temperature or spin speed has been altered the machine will store the changes in memory at the start of a programme When this programme is chosen again these settings will appear in the display The machine is delivered with the memory function deactivated Anti crease Anti crease helps prevent creasing if the laundry is not normally removed immediately after the end of a programme The drum will continue to rotate for up to 30 minutes after the programme end The washing
39. machine door can be opened at any time On the machine is delivered with this option selected as standard Anti crease is activated Off Anti crease is deactivated 67 Settings menu Water intake You can choose between cold water and hot water intake Cold The machine is delivered with this option selected as standard The washing machine will be operated with cold water Hot cold To save energy warm water will be used during the main wash ifa temperature of 40 C or higher is selected Exceptions The programme Woollens only use cold water You can heat up your water with cheaper energy saving options e g gas solar power oil The temperature has to be below 60 C ZN For hygienic reasons the intake hose with the blue marking must be connected to the cold water main 68 Miele washing machines offer perfect care for your laundry and feature a wide range of special programmes designed to suit the fabric being washed And now Miele have developed a range of specialist CareCollection detergents and conditioning products to offer you a complete package for cleaning and caring for your laundry The Miele CareCollection detergents and conditioning products are listed below You can order these and many other useful products via the internet at www miele shop com All the products can also be ordered from Miele see back cover for contact details Optional accessories Ca
40. n has been activated an audible tone sounds at the end of the programme There are two volumes Off the machine is delivered with this option selected as standard The buzzer is switched off Normal The buzzer sounds at normal volume at the end of the programme Loud The buzzer sounds at loud volume at the end of the programme A tick Y will appear beside the option to show that it has been set 65 Settings menu Keypad tone An audible tone sounds each time a button is pressed The machine is delivered with the keypad tone switched off Atick Y will appear beside the option to show that it has been set Display brightness There are ten different display brightness settings The machine is delivered with the display brightness on setting 5 The bar chart shows you the setting This will change as soon as a different setting is chosen 66 Display contrast There are ten different display contrast settings The machine is delivered with the display contrast on setting 5 The bar chart shows you the setting This will change as soon as a different setting is chosen Text brightness There are ten different brightness settings for the lights Start Delay start Extras and Spin speed The machine is delivered with the lights brightness on setting 5 The bar chart shows you the setting This will change as soon as a different setting is chosen Standby disp
41. ner or the liquid starch to compartment amp Do not exceed the maximum level mark It will be automatically dispensed in the last rinse At the end of the programme a small amount of water remains in the fabric conditioner compartment amp Detergent If starching frequently thoroughly clean the dispenser compartment especially the siphon tube and fabric conditioner channel regularly See Cleaning the detergent dispenser drawer Do not use powder starch formulations or viscous liquid starch in the compartment as it will clog up Adding fabric conditioner or starch separately m Dispense in accordance with manufacturer s instructions on the packaging m Add powder or viscous starch to compartment LU Add the fabric conditioner or liquid starch to compartment amp m Turn the programme selector to Separate rinse Starch m Select a spin speed m Press the Start button Colour run and dye removers dyes m Do not use colour run or dye removers in this machine m Dyes suitable for use in domestic washing machines can be used However please note that the salt used in the dyeing process can cause corrosion to stainless steel components in the machine if you dye frequently Follow the manufacturer s instructions carefully 35 Cleaning and care N Disconnect the machine from the mains electricity supply and withdraw the plug from the socket before cleaning the machine N The washing machine must n
42. ng agents They do not remove fruit coffee and tea stains Use a general purpose detergent containing a bleaching agent Add stain remover to the compartment WY Never put stain removers and liquid detergent together in the dispenser drawer Grey greasy particles cling to washed laundry Insufficient amounts of detergent were used The laundry was heavily soiled with grease Use more detergent Before washing the next load run a Cottons 60 C programme with liquid detergent but without a load White residues which look like powder detergent are seen on dark textiles after washing The detergent contained compounds zeolites to aid water softening which are not soluble in water These have stuck to fabrics Try and brush off the residues with a soft brush once the laundry is dry Wash dark textiles using a detergent which contains no zeolites Liquid detergents usually contain no zeolites Use the Dark garments programme 42 Problem solving guide The drum door does not open when you press the Door button Possible cause Remedy The machine is not connected to the electricity supply and or is not switched on Insert the plug in the socket and switch on and or switch the machine on with the button Access via a code has been activated Deactivate the code as described in the Settings menu Power outage Open the drum door as described in
43. nstallations e g on a ship gt Do not make any alterations to the washing machine unless authorised to do so by Miele Correct use gt Do not install your washing machine in rooms where temperatures below freezing may occur Frozen hoses may burst or split The reliability of the electronic control unit may be impaired at temperatures below freezing point gt Before using the washing machine for the first time check that the transit bars at the rear of the machine have been removed see section on Installation During spinning a transit bar which is still in place may result in damage to both the machine and adjacent furniture or appliances gt Turn off the tap if the machine is to be left for any length of time e g holi day especially if there is no floor drain gully in the immediate vicinity gt Flooding danger If hooking the drain hose into a wash basin check that the water can drain off quickly enough to prevent the sink from overflowing Make sure the drain hose is secure so that the force of the water flowing out of the hose does not dislodge it gt Take care to ensure that foreign objects e g nails pins coins paper clips do not find their way into the machine with the laundry These may damage components of the machine e g suds container drum which in turn can result in damage to the laundry Warning and Safety instructions gt If the correct amount of detergent is dis
44. number 6134691 is available from Miele 33 Detergent The right amount to dispense will depend on the following The quantity of the laundry The soiling level of the laundry Lightly soiled No visible dirt or stains Possibly slight body odour Normally soiled Visibly dirty and or just a few slight stains Heavily soiled Stains and soiling clearly visible The water hardness level Check with your local water supplier if you do not know the hardness level in your area 34 Water softener A water softener can be used to cut down on the use of detergents in hard water areas Dispense according to the amount specified on the packaging First add detergent and then the water softener Use a quantity of detergent as for soft water Washing with several components If you wash using several components e g special application detergents we recommend always dispensing the agents into compartment UW in the following order 1 Detergent 2 Water softener 3 Stain remover This way the agents are distributed more evenly Fabric conditioners and liquid starch Fabric conditioners make garments soft to handle and help prevent static cling when tumble drying Starch stiffens and gives body to items of laundry e g shirts tablecloths and bed linen Automatic dispensing of fabric conditioner or liquid starch to laundry at the end of a programme m Add the fabric conditio
45. or shorter depending on this absorbency rate Delay start The delay start time selected will appear in the display After the machine has started the delay start time counts down Once the delay start time has finished the programme begins and the estimated programme duration appears in the display Settings The settings can be used to tailor washing programmes to suit your individual requirements The selected function will be shown in the Settings menu Before using for the first time 1 Welcome screen Before using the machine for the first time ensure that it is correctly installed and connected See Installation and connection This washing machine has completed a comprehensive functional test A small quantity of water remains in the drum as a result The initial operation consists of four steps The washing machine guides you automatically through steps 1 to 3 m Place the display fascia onto the For safety reasons spinning is not panel possible until the machine has been prepared for using for the first time To m Press the button in activate the spinning function you must r run a wash programme without laundry Miele and without detergent Using detergent could result in an excessive build up of foam Willkornmen The welcome screen will appear in the display every time the washing machine is switched on until a programme lasting longer than 1 hour has been complete
46. ot be hosed down External casing and fascia panel m Clean the casing with a mild non abrasive cleaning agent or soap and water using a well wrung out cloth Wipe dry with a soft cloth m The drum can be cleaned using a suitable proprietary stainless steel cleaning agent following the manufacturer s instructions on the packaging NDo not use solvents abrasive cleaners glass cleaners or all purpose cleaning agents These might damage plastic surfaces and other components because of the chemicals they contain 36 Extra cleaning Carry out a hot wash 70 C or above with powder detergent approx every 6 weeks to help prevent deposits building up in the machine These can occur when washing is mainly done at low temperatures and also lead to unpleasant smells If you have no reason to wash occasionally at this high temperature then run a Cottons 95 C programme with detergent but no laundry at regular intervals Cleaning the detergent dispenser drawer The two main detergent compartments of the dispenser drawer are self cleaning The drawer should be removed and cleaned regularly for hygiene reasons m Pull out the detergent dispenser drawer until a resistance is felt Press down the release catch and at the same time pull the drawer right out of the machine m Clean the detergent drawer with warm water Cleaning and care Cleaning the detergent dispenser drawer housing m Clean the
47. pensed the machine should not need to be descaled If however you do wish to descale the machine only use Miele Descaler for washing machines and strictly observe the instructions on the packaging If in doubt contact Miele or your Miele Chartered Agent gt Textiles which have been pre treated in solvent based cleaning agents must be thoroughly rinsed in clean water before being washed in the machine gt Never use solvent based cleaning agents e g those containing benzene in this machine as this may result in damage to component parts and create toxic fumes Such agents also pose a fire and explosion hazard gt Never use solvent based cleaning agents e g those containing benzene to clean the outside surfaces of this machine They can cause damage to plastic surfaces gt Only use dyes specified by the manufacturer as being suitable for use in a domestic washing machine Always observe the manufacturer s instructions carefully gt Colour run and dye removers contain sulphur compounds which can Cause damage such as corrosion Do not use these products in this machine gt If liquid detergent comes into contact with the eyes rinse them thoroughly with lukewarm water imme diately If swallowed seek medical assistance immediately and retain the packaging or label for reference Those with skin problems or sensitive skin should avoid their skin coming into contact with liquid detergent gt Only remov
48. r Width for building under Depth for building under Weight Capacity Voltage Rated load Fuse rating Consumption data Water flow pressure minimum Water flow pressure maximum Inlet hose length Drain hose length Connection cable length Drain pump head max Drain pump length max Test certificates awarded Technical data 850 mm 595 mm 615 mm 993 mm 820 mm 600 mm 650 mm 98 kg 7 5 kg dry laundry See data plate See data plate See data plate see Consumption data 100 kPa 1 bar 1000 kPa 10 bar 1 60 m room 1 60 m 1 00 m 5 00 m See data plate Including building under kit See Installation and connection 59 Consumption data Consumption data for the nominated energy labelling programme according to AS NZS 2040 1 amp AS NZS 2040 2 Standard Load Consumption data Energy Water Duration in kWh in litres Normal Cold Water Cottons 40 C 7 5kg 0 56 62 2h 24 min Notes for test institutes Detergent must be dispensed via the detergent dispenser drawer Consumption data can vary from the nominal values given depending on water pressure water hardness water inlet temperature room temperature type and volume of load fluctuations in the electricity supply and any Extra options selected 60 Consumption data Load Consumption data Energy Water Duration in kWh in litres Cottons IS 7 5 kg
49. r of the fabric and preventing static build up Down ltems This special purpose detergent contains a mild tenside and has been specially formulated to keep down filled items supple and to give them bounce 70 71 Miele Australia Pty Ltd ABN 96 005 635 398 Melbourne 1 Gilbert Park Drive Knoxfield VIC 3180 Telephone 1300 464 353 Fax 03 9764 7149 Sydney 3 Skyline Place Frenchs Forest NSW 2086 Telephone 1300 464 353 Fax 02 8977 4249 Brisbane 39 Harvey Street North Eagle Farm QLD 4009 Telephone 1300 464 353 Fax 1800 799 578 Adelaide 83 85 Sir Donald Bradman Drive Hilton SA 5033 Telephone 1300 464 353 Fax 1800 799 578 Perth 205 207 Stirling Highway Claremont WA 6010 Telephone 1300 464 353 Fax 1800 799 578 www miele com au Miele www miele shop com Alteration rights reserved 481 1 ce Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland New Zealand Telephone 0800 264 353 Fax 0800 463 453 www miele co nz Germany Miele amp Cie KG Carl Miele StraBe 29 33332 Gutersloh M Nr 07 647 500 03
50. ramme The washing machine door can be opened at any time 2 A third rinse is carried out if there is too much foam in the drum aspin speed lower than 700 rpm has been selected Without spin has been selected 3 A third rinse is carried out if Without spin has been selected 29 Changing the programme sequence Cancelling a programme You can cancel a programme at any time after it has started m Turn the programme selector to Finish The suds will be pumped away If you want to remove the laundry m Press the Door button If you want to select a different programme m Switch the machine off with the button m Switch the washing machine back on again m Check if there is still detergent in the detergent dispenser drawer If necessary refill detergent m Turn the programme selector to the required programme m Press the Start button to start the programme 30 Interrupting a programme m Switch the machine off with the button To continue with the same programme m Switch the machine on again with the button Change Programme and temperature After the start of a programme it is no longer possible to select a different programme Spin speed Once a programme has started you can change the spin speed up until the final spin begins Extra options It is possible to select or deselect the Short and Water plus Extra options up to 5 minutes after the programme
51. reCollection Miele specialist detergents Fabric softener Miele s fabric softener will give your laundry a fresh natural fragrance lt makes garments soft to handle and prevents static build up during tumble drying For delicates This liquid detergent is ideal for the gentle treatment of delicate fabrics such as wool and silk Its special formulation cleans effectively at temperatures as low as 20 C while protecting the colour of your delicate garments UltraWhite This multi purpose powder detergent has excellent stain removal properties and is suitable for white and light coloured laundry as well as heavily soiled coloured items Sensitive skin Miele s sensitive skin laundry detergent has been specifically tested and formulated for consumers with sensitive skin and allergies This detergent is powerful and deep cleaning for optimal stain removal even at 40 C leaving your laundry with a fresh mild fragrance 69 Optional accessories UltraColor Available in a liquid and powder form this detergent is particularly suitable for cleaning coloured and dark garments The special formulation offers effective stain removal even at low temperatures while helping to prevent colours fading Sportswear The Miele sportswear detergent is designed to clean sportswear whilst taking care of the special microfibres used in these garments It will help to neutralise and remove odours whilst protecting the colou
52. sed A Only use an oxygen based bleach or a non chlorine bleach A Do not bleach 27 Programme sequence Main wash Rinses Spinning Water Wash Water Rinses Interim Final level rhythm level spin spin Cottons lu a 2 3 y y Minimum iron a 2 39 y y Delicates E D ed 3 Vv Darks and denim ky k 3 J Woollens Ww lea ey 2 J y Separate 2 y rinse Starch Drain Spin V See the next page for legend 28 Low water level Medium water level BEE High water level Intensive rhythm Normal rhythm Gentle rhythm Sensitive rhythm Ultra sensitive rhythm 000006 Handwash rhythm This machine has fully electronic controls with automatic load recognition lt takes in the right amount of water required for the programme depending on the amount of laundry and its absorbency rate This means that programme cycles and durations can vary The programme sequences outlined in the chart are based on the basic programme with a full load Extra options which can be selected have not been taken into account The display shows the stage the programme has reached Programme sequence Special features in the programme sequences Anti crease The drum will continue to rotate for up to 30 minutes after the programme end to avoid creasing Exceptions There is no crease protection in the Woollens prog
53. the programme selector to Finish Anti creaze m Switch the machine off with the Finished button Enz m To avoid the build up of mildew it is m Press the Door button again to open recommended that the door is left the door ajar when the machine is not in use The machine will switch off automatically 15 minutes after the end of the Anti crease phase Push the D button to switch the machine back on m Remove the laundry Programme selection Fibres Textiles Colour Programme Cottons linens or cotton i Cottons 95 C mixed fabrics gt ligh gt E E underwear table and bed linen towels etc Cottons 40 C a dark Ip Cottons 30 C Synthetic fibres mixed fibres rayon and easy care cottons trousers blouses skirts eic y light Minimum iron 60 C p gt dark Minimum iron 40 C Minimum iron 30 C Delicate items made of synthetic fibres mixed fibres or rayon stockings blouses etc gt light Delicates 40 C dark Curtains Delicates 30 C Items made of cotton mixed fibres and or denim gt dark cm Dark garments Jeans 40 C Woollens mixed wool and handwashable items Please follow the manufacturer s care instructions 20 Woollens 30 C Programme select
54. tion Please note Adapter 2 Nut 3 Hose clip End of the hose m Fit adapter to the sink drain outlet using nut m Attach the end of the hose to adapter m Use a screwdriver to tighten hose clip up close to the nut 57 Installation and connection Electrical connection The washing machine is supplied with a mains cable with moulded plug for connection to a 230V mains supply The voltage rated load and plug rating are given on the data plate Please ensure these match the household mains supply The accesibility of the plug must always be ensured in order to separate the washing machine from the mains All electrical work should be carried out only by a suitably qualified and competent person in strict accordance with national and local safety regulations For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA Ensure power is not supplied to the appliance until after installation work has been carried out Connection should be made via a suitable switching socket which is easily accessible after installation in order to separate the washing machine from the mains Do not connect via an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating WARNING THIS APPLIANCE MUST BE EARTHED 58 Height Width Depth Depth with door open Height for building unde
55. tions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Correct application gt The washing machine is designed exclusively for domestic purposes and must only be used to wash garments which have been declared suitable for washing by the manufacturer indicated on the garment care label Any other use may be dangerous The manufacturer cannot be held liable for damage resulting from incorrect or improper use or operation gt The washing machine is not suitable for outdoor use gt This washing machine is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning its use by a person responsible for their safety gt This washing machine must not be installed and operated in mobile installations e g on a ship Safety with children gt Keep children away from the washing machine at all times lt is not a toy To avoid the risk of injury do not allow children to play on or near it or to play with its controls Supervise children whilst you are using it gt Older children may only use the washing machine if its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse gt For machines with a porthole door remember that the porthole glass will
56. unnecessary service visits where the problem could have been rectified as described in these Operating instructions Please note Repair work to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work The programme does not start Problem Possible cause Remedy The display remains dark and the indicator lights for the programme buttons are not lit up There is no power to the machine Check whether the mains plug is plugged in and switched on the fuse or circuit breaker has tripped You are asked to enter a code Access via a code has been activated Enter the code and confirm the entry Deactivate the code if you do not wish this message to appear in the display the next time the machine is switched on The display is dark The display has switched off automatically to save energy Standby mode Press any button Standby comes to an end 39 Problem solving guide Fault messages in the display Problem Possible cause Remedy O EJ Fault The water outletis Clean the drain filter and ae blocked or the drain pump d restricted The maximum delivery The drain hose has head is 1 m been fixed
57. with the washing machine A stacking kit is necessary and can be purchased from Miele Please note a Safety distance to wall at least 2 cm b Height Stacking kit with pull out shelf approx 169 cm Stacking kit without pull out shelf approx 170 cm NA washer and dryer should never be stacked without using the proper stacking kit Doing so is extremely dangerous as the dryer may vibrate off of the washing machine during use 53 Installation and connection The Miele Waterproof system The Miele Waterproof system protects all parts of the washing machine from water damage The system consists of three main components 1 the inlet hoses 2 the electronic unit and the washing machine housing 3 the drain hose 1 Inlet hoses The inlet hoses are fitted with additional electrical safety valves which work like automatic taps and are housed in the inlet hose connection boxes They are pressure proof to between 7000 and 10000 kPa The inlet hoses have a protective sleeve Any leaking water from the inlet hose is fed into the sump through the protective covering which surrounds the inlet hose as a second skin The float switches off the safety valves preventing water flowing into the machine and water in the suds container is pumped away 54 2 Electronic unit and washing machine housing Sump Any leaking water is collected in a sump in the b
Download Pdf Manuals
Related Search