Home

Operating instructions Heat pump tumble dryer

1. Ironing ZA Very hot Z Hot A Warm zx Do not iron Laundry care when drying in a tumble dryer See the Programme chart This describes the programmes and gives their maximum load Load according to the optimum amount of laundry recommended for the programme being used Underloading is uneconomical Overloading gives a poorer quality of drying and may cause unnecessary creasing With half loads you can select the Auto load control Extra Select an appropriate drying level eg Normal plus if you want to fold and put away the laundry after you take it out of the dryer Machine iron if the laundry e g table linen requires further processing after drying Down filled garments have linings which have a tendency to shrink depending on the quality of the item They can be partially dried using the Gentle smoothing programme Pure linen should only be machine dried if specified as suitable by the manufacturer on the care label as the surface of the fabric may otherwise become rough It can be partially dried using the Gentle smoothing programme Woollens and wool blends tend to become matted and shrink if dried in a tumble dryer They can however be fluffed up in the Woollens handcare programme Loopknit garments e g T shirts and underwear tend to shrink depending on their quality Do not overdry these textiles When purchasing these garments
2. The laundry is not sufficiently dry The load consisted of different types of fabric m Finish drying using the Warm air timed drying programme m Select a more suitable programme next time Tip You can alter the residual moisture level for some programmes See Settings menu Laundry or feather filled pillows smell after drying The laundry was washed with insufficient detergent Feathers are a natural product and this is quite normal m Laundry use sufficient detergent next time m Pillows take out of the tumble dryer and aerate m Use a fragrance flacon available as an optional accessory for your favourite fragrance Items made of synthetic fibres are charged with static electricity after drying Synthetic fibres tend to attract static charge m Static charge can be reduced by adding a fabric softener to the final rinse in the washing programme There is a build up of fluff Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed Machine drying hardly causes any fluff to form Fluff is collected by the fluff filters and the plinth filter and can be removed easily m See Cleaning and care 61 Problem solving guide Other problems Problem Possible cause and remedy The drying process goes on too long or even switches off The room in which the tumble dryer is located is too warm m Ventila
3. 17 Operating the tumble dryer Display a ii w V OK A EcoFeedback L J Settings Duration Start Stop Drying level Delay start C V OK sensors These sensors are used to operate the display when the symbols light up V sensor Scrolls down the list to the next option or decreases a value OK sensor Confirms the programme selected a value set or opens a sub menu sensor Scrolls up the list to the next option or increases a value The sensor symbols will go out if no selection is made They will also go out if a selection is not confirmed with OK EcoFeedback sensor See EcoFeedback for more information 18 Settings The Settings menu is opened by touching the V and sensors at the same time Settings can be changed to alter the dryer s electronics to suit different requirements Please refer to Settings menu at the end of this booklet for more information The following programmes are selected using the programme selector at the Further programmes position Automatic plus Delicates Silks handcare Sportswear Standard pillows Outerwear Proofing Warm air Cool air Basket programme Cottons hygiene Operating the tumble dryer Perfect Dry indicator With programmes with a selectable drying level the Perfect Dry system calculates the residual moisture present in the laundry
4. EARTHED Consumption data Load Final spin speed in a Residual Energy Duration domestic washing moisture machine kg rpm kWh min Cottons lt _ 8 0 1000 60 1 87 149 4 0 1000 60 18 95 Cottons Normal 8 0 1200 53 1 65 135 8 0 1400 50 1 60 128 8 0 1600 44 1 40 114 Cottons Normal Gentle tumble 8 0 1000 60 1 92 163 Freshen up 3 0 1000 60 1 09 95 Cottons Hand iron 08 8 0 1000 60 1 55 125 8 0 1200 53 1 35 109 8 0 1400 50 1 25 102 8 0 1600 44 1 10 87 Minimum iron Normal 4 0 1200 40 0 60 55 Gentle tumble 4 0 1200 40 0 60 55 Freshen up 4 0 1200 40 0 76 65 Minimum iron Hand iron 08 4 0 1200 40 0 50 48 Automatic plus Normal 5 0 800 50 1 30 110 Shirts Normal 2 0 600 60 0 65 58 Delicates Normal 2 5 800 50 0 58 54 Sportswear Normal 3 0 800 50 0 90 76 Outerwear Normal 2 5 800 50 0 78 70 Denim Normal 3 0 900 60 1 26 110 Express Normal 4 0 1000 60 0 96 82 1 Weight of dry laundry All data was calculated using EN 61121 unless otherwise stated Power consumption when switched off 0 10 W Power consumption when not switched off 2 50 W 79 Consumption data Consumption data can vary from the nominal values given above depending on the size of the load types of textiles residual moisture levels after spinning fluctuations in the electricity supply and any options selected Using the Cottons Extra dry programme is recommended for a mixed cotton load and i
5. _123 abc MS 3 Saving a name Save name reg Z 123 abc T m Touch the V or A sensor to highlight the V symbol m Confirm by touching the OK sensor The programme will be saved as a favourite Changing a Favourite programme Favourite programmes m Select Change m Select the Favourite programme that you want to change m Change the favourite programme and save it under the same name or change the name The modified parameters will be active when the Favourite programme is started again Deleting a Favourite programme If 10 Favourite programmes are saved you will need to delete one of them before being able to save a new programme m Select Delete m Select the Favourite programme that you want to delete m Confirm the deletion 35 Mixed items For drying a mixed load of items which can be compiled from a list m Turn the programme selector to Mixed items m Touch the V or A sensor to highlight items A list of 19 items will appear in alphabetical order in the display m Confirm the item you want by touching the OK sensor The item selected will have a M next to it and the following will appear in the display Individual items mix Change selection Finish selection Display selection m Touch the V or A sensor to highlight an option m and confirm by touching the OK sensor Changing or adding to the selection m You
6. carefully N A clogged filter is a fire hazard The fluff filter must be cleaned after every programme The maximum load for this tumble dryer is 8 0 kg dry weight See the Programme chart for the maximum recommended loads for individual programmes gt To prevent the risk of fire do not connect the tumble dryer via a controllable socket e g a timer or a peak load switch off device If the drying programme is interrupted before the end of the cooling down phase this could cause the laundry to self ignite Warning and Safety instructions To prevent the risk of fire the following textiles must not be dried in this tumble dryer Items which have not been washed Items such as workwear which have not been thoroughly cleaned and which are still soiled with grease oil or other desposits Such as cosmetics lotions etc If items have not been thoroughly cleaned there is a danger that these might ignite when heated even after they have been removed from the dryer at the end of the programme Items that have been soiled with substances such as cooking oil acetone petrol kerosene spot removers turpentine waxes wax removers and other chemicals e g mops and floor cloths Items which have been splashed with hair lacquer hair spray nail varnish remover or similar substances When washing such heavily soiled items ensure that you use sufficient detergent and select a high temperature If i
7. it is advisable to take their shrinkage properties into account Select the Gentle tumble Extra for fabric which is particularly heat sensitive or susceptible to creasing 25 2 Loading the tumble dryer A It is essential to read 1 Notes on correct laundry care first of all m Switch the tumble dryer on by pressing the button The interior drum lighting will come on The interior drum lighting will automatically go out after a few minutes and or after the start of a programme to save energy If you are not using a fragrance Opening the door flacon the tab must be pushed down completely see arrow Closing the door m Reach under the door grip and pull the door open m Unfold the laundry and load loosely into the drum m Shut the door with a gentle swing Do not overload the drum Overloading can cause unnecessary wear and tear to the laundry give a disappointing drying result and cause more creasing When closing the door make sure that laundry does not get trapped in the door opening This could damage the laundry 26 3 Selecting a programme and starting it Selecting a programme Further programmes The further programmes can be selected via the display Cottons 34 Further programmes Cottons Favourites Minimum iron Mixed items Cott ottons lt _ Meer programmes Woollens Expres
8. Clean out airways only appears when there is a heavy build up of fluff Normal Factory default setting 83 Settings menu Light Clean out airways appears when there is only a small build up of fluff Buzzer volume The buzzer can be set to be louder or quieter The setting selected is shown in a bar chart Factory default a medium setting Quieter 8 22 3 Louder BEBE EE E NI You will hear the buzzer change as the setting is selected Keypad tone Condition for low conductivity setting This programmable function should only be set if the water used for washing the laundry is extremely soft with a conductivity reading electrical conductivity less than 150 uS cm Contact your local water authority for the conductivity level of your mains water supply A Only activate the Low option if the above condition is present Otherwise drying results will be unsatisfactory Total consumption You can display the total Options On Off the machine is delivered with this option selected as standard Conductivity A Low This setting should only be altered if the water is so soft that it is likely to cause the electronics which sense residual moisture in the laundry to give false readings Options Normal Factory default setting Low 84 consumption When this function is activated a tone Options will sound each time a button is pressed Dis
9. Miele Operating instructions Heat pump tumble dryer To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time en AU NZ M Nr 10 207 610 Caring for the environment Disposal of the packing Ensure that your old appliance presents material no danger to children while being 20 stored for disposal The packaging is designed to protect the appliance from damage during Energy saving tips transportation The packaging materials used are selected from materials which TO avoid unnecessarily long drying are environmentally friendly for disposal times and high consumption of energy and should be recycled Make sure that your laundry is Recycling the packaging reduces the thoroughly spun before drying use of raw materials in the The higher the spin the greater the manufacturing process and also savings that can be made in energy reduces the amount of waste in landfill and time during drying e g approx sites Ensure that any plastic 20 energy can be saved if spun at wrappings bags etc are disposed of 1600 rpm instead of 1000 rpm safely and kept out of the reach of Load according to the optimum babies and young children Danger of amount of laundry recommended for suffocation the programme being used Underloading is uneconomical Disposing of your old Overloading gives a poorer quality of appliance drying and may c
10. V or A sensor to enter the hour and confirm your entry with the OK sensor m Use the V or A sensor to enter the minutes and confirm your entry with the OK sensor Drying levels Extended cool down The automatic cooling down phase which takes place before the end of a programme can be extended for all programmes with selectable drying levels in 2 minute increments up to 18 minutes This makes the garments easier to handle You can alter the drying levels for the Cottons Minimum iron and Automatic plus programmes The setting selected is shown in a bar chart Factory default a medium setting Damper 222227 The programme duration is shorter Drier EEHEEHE The programme duration is longer Exception The Cottons lt __ programme will remain unchanged Options 00 minutes factory default 02 04 06 18 minutes Airways indicator Fluff should be removed after drying The Clean out airways message will remind you to clean the filters when a certain amount of fluff has collected in them You can decide at what level of fluff this reminder should be given You will have an idea of how often this should be done after a few drying programmes Options Off Clean out airways does not appear In cases of a very severe blockage in the airways the programme will be cancelled and the Clean out airways message will appear regardless of this option Heavy
11. caps waterproof textiles rubberised articles and items of clothing and pillows with foam rubber filling Damaged fabrics which contain padding or fillings e g pillows jackets When damaged the filling can get out with the risk of it igniting in the dryer In many programmes the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them this also avoids the danger of the laundry self igniting The programme is not finished until the cooling down phase has been completed As soon as the programme has finished remove all laundry from the drum gt Do not let anyone sit or lean on the door as this can cause the tumble dryer to tip up Always close the door after use This way you will avoid the danger of children climbing onto or into the dryer or hiding things in it pets or other small animals climbing into it Warning and Safety instructions The tumble dryer must not be used without or with damaged fluff filters with a damaged plinth filter This would cause an excessive build up of fluff which in turn would cause a fault gt The fluff filters must be cleaned after every drying cycle Fluff must not be allowed to accumulate around the tumble dryer gt The fluff filters and the plinth filter must be thoroughly dried after cleaning Do no replace them if they are damp or wet Damp or wet filters could cause operational
12. correct one for the Miele washing machine and Miele tumble dryer Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions 16 Operating the tumble dryer Control panel ae i w EcoFeedback V OK A i settings Start Stop Drying level Duration Delay start C gt C Se Gentle tumble Freshen up Auto load control Anti crease Buzzer Cottons CI Further programmes Cottons Favourites Minimum iron Mixed items Woollens Express handcare Denim Gentle smoothing Shirts Steam smoothing Display with sensors See the following page for more information 2 Start Stop button For starting the programme selected and cancelling a programme once it has started 3 Drying level button For all programmes with a selectable drying level Duration button For selecting the duration for timed drying programmes Delay start button For selecting Delay start O Extras buttons Various options can be added to the programmes Programme selector For selecting the programme Optical interface For service technicians 9 D button For switching the tumble dryer on and off To save energy the tumble dryer will switch off automatically 15 minutes after the end of the programme anti crease phase or after being switched on if no other selection is made
13. faults gt Do not install the tumble dryer in a room where there is a risk of frost occurring At temperatures around freezing point the tumble dryer may not be able to operate properly There is a risk of damage if the condensed water is allowed to freeze in the pump and hoses gt If the water is drained externally through the drain hose instead of being collected in the condensed water container make sure the drain hose is securely attached if you hang it in a sink or basin to avoid the hose slipping and the water causing damage gt Condensed water is not drinking water It can cause health problems in both people and animals Always keep the area around the tumble dryer free of dust and fluff Dust drawn into the tumble dryer can cause blockages in the heat exchanger over time gt The tumble dryer must not be hosed down 14 Warning and Safety instructions Using a fragrance flacon optional accessory gt Only use genuine Miele original fragrance flacons The fragrance flacon must be stored in its packaging so please make sure you retain this gt Caution The fragrance can run out of the flacon Make sure that you always keep the flacon or the fluff filter with the flacon inserted in it in a horizontal position when carrying and do not tip or place down on any surface gt Use an absorbent cloth immediately to wipe up any fragrance which has run out of the flacon onto the floor the dryer or any dry
14. for unauthorised work Messages in the display Problem Possible cause and remedy Code 000 flashes lights up after switching on Access via a code has been activated m See Settings menu PIN Code Adjust the load The drum is empty or the laundry is too dry lights up after a programme is cancelled This is not a fault In some programmes if the drum has been underloaded or is empty the programme will be cancelled This can also happen if the items are already dry m Open and close the door to resume drying m Use the Warm air programme timed drying to dry individual items N Technical fault F If restart is unsuccessful call Miele lights up after a programme is cancelled There is no obvious cause m Switch the dryer off and then on again m Start a programme If the programme is cancelled again and an error message appears there is a fault Contact Miele 58 Problem solving guide Problem Possible cause and remedy i Information Clean out airways lights up at the end of a programme There is a build up of fluff in the airways m Clean the fluff filters m Clean the plinth filter See Cleaning and care To switch off the message m Select OK Clean out airways Clean the fluff filter and check the airways lights up after a programme is cancelled An excessive amount of fluff has built up m Clean the fluff filters m Clean
15. holder with your below thumbs black arrows and m pull the hose holder forwards to remove it white arrows A If you want to drain the water off into a sink or basin you will need to secure the hose carefully e g by tying it to a tap to make sure it cannot slip during use see the drawing under Installation and connection Front view Overflowing water can cause damage m The non return valve can be fitted in the end of the hose You can refit the hose holder at a later stage if you decide that you no longer want to drain the condensed water externally 76 Installation and connection 1 Adapter 2 Nut 3 Hose clip 4 End of the hose secured with the hose holder 5 Non return valve 6 Tumble dryer drain hose m Fit the adapter 1 to the sink drain outlet using the nut 2 The nut is usually fitted with a washer which must be removed m Attach the end of the hose 4 to the adapter 1 m Use the hose holder m Use a screwdriver to tighten the hose clip 3 up close to the nut m Fit the non return valve 5 to the tumble dryer drain hose 6 The non return valve 5 has to be fitted so that the arrow points in the direction of flow i e towards the sink m Secure the non return valve using hose clips 77 Installation and connection Electrical connection This tumble dryer is supplied with a mains cable with moulded plug The accessibility of the plug must be
16. near the appliance Drying durations may increase slightly Optional accessories Washer dryer stack The tumble dryer can also be combined with a Miele washing machine in a washer dryer stack The appropriate Miele washer dryer stacking kit is required 73 Installation and connection Externally draining condensed water Notes When drying is in progress condensed water is pumped into the condensed water container through the drain hose which is located at the back of the dryer The condensed water can also be drained away via the drain hose so that the condensed water container does not have to be emptied Drain hose length 1 60 m Maximum delivery head 1 50 m Maximum drain hose length 4 00 m The following optional accessories are available an extension hose anon return valve kit for connection to an external water outlet The kit includes an extension hose 74 Installation conditions requiring a non return valve A There is a risk of backflow into the dryer if a non return valve is not fitted Backflow could damage the dryer and also the room in which it is located Certain installation conditions such as those described below require the fitting of a non return valve Maximum delivery head with non return valve fitted 1 00 m Installation conditions requiring the fitting of a non return valve Drainage into a sink or floor gully where t
17. on The programme selector must not be at the Further programmes Favourites Mixed items positions m Touch the V and sensors at the same time The following will light up in the display settings Language M B Time Drying levels You are now in the Settings menu Selecting settings m Touch the V or sensor until the setting you want appears in the display The V sensor scrolls down the list The sensor scrolls up the list m Confirm by touching the OK sensor 82 Changing a setting m Touching the V or sensor will call up the different options for the setting For example you can select a value If the option is marked with a v it is active change a bar chart change numbers m Confirm by touching the OK sensor Closing the Settings menu m Touch the V or sensor repeatedly until Back lt gt appears in the display m Confirm by touching the OK sensor Language The display can be set to appear in one of several different languages The flag N after the word Language Sprache in German acts as a guide in case a language which is not understood has been set Settings menu Time First select either a 24 hour or 12 hour clock You can then set the current time of day Clock format 24h Clock 12h Clock m Select the clock format you want with the V or A sensor and confirm with the OK sensor Setting the time of day m Use the
18. operating A programme cannot be started There is no obvious cause m Connect the tumble dryer to the mains electricity supply m Turn on the tumble dryer m Close the door m Check whether the mains fuse has tripped Has there been a power cut When power is restored any previously running programme will restart automatically The display is dark and the Start Stop button is flashing slowly The dryer is in standby This is a normal function and does not indicate a fault The drum will turn at intervals in the anti crease phase m See Settings menu Display switch off status The dryer is switched off at the end of the programme The dryer switched off automatically This is quite normal and does not indicate a fault m See Settings menu Appliance switch off status The interior drum lighting does not come on The drum lighting will switch off automatically When the door is closed after a few minutes when the door is open to save energy If the dryer is switched on the drum lighting will come on when the door is opened 63 Problem solving guide Problem Possible cause and remedy Insufficient spray to remoisten the laundry The filter in the condensed water container is blocked m Clean the filter in the condensed water container optional accessory see end of this section The spray jet in the door opening is heavily
19. select the intensity of the fragrance m Turn the outer ring clockwise a little m Turn the outer ring clockwise the further you open the flacon the more intense the fragrance Damp laundry and longer drying durations with sufficient heat transfer are needed for the fragrance to be released into the laundry effectively 55 Fragrance flacon The fragrance will also be noticeable in the room air during the process Fragrance is not released when using the Cool air programme After drying To avoid the fragrance escaping needlessly m Turn the outer ring anti clockwise until marker 2 is in position You will feel a slight resistance If you want to dry laundry without adding fragrance occasionally remove the fragrance flacon and store it in its original packaging until you want to use it again See the following section 56 Replacing the fragrance flacon When the fragrance is no longer sufficiently intense m Turn the outer ring anti clockwise until markers and line up m Replace the fragrance flacon with a new one Fragrance flacons are available to order from Miele or online at www miele shop com depending on country Fragrance flacon When purchasing new fragrance flacons only remove the protective seal just before use Cleaning the fluff filters The intensity of the fragrance will be diminished if the fluff filters and th
20. the pillow feels dry Weight of dry laundry 42 Programme chart Outerwear Max load 2 5 kg Normal Hand irond Items Outerwear which is suitable for drying in a tumble dryer Proofing Max load 2 5 kg Normal Items Drying microfibre fabric skiwear outerwear fine closeweave cotton garments poplin or tablecloths which are suitable for drying in a tumble dryer and have been treated to provide a water and dirt resistant finish Notes This programme includes a proofing fixing phase Only use proofing agents which are stated by the manufacturer as being suitable for use on membrane textiles as these contain fluorochemical compounds Do not dry items which have been treated with proofing agents containing paraffin Fire hazard Warm air Max load 8 0 kg Items Multi layered fabric whose layers have different drying characteristics e g jackets pillows sleeping bags and other voluminous items For drying individual items e g bath towels bathing costumes tea towels and small loads Note Do not select the longest drying time to start with Check the items as you are drying them to find the optimum time Cool air Max load 8 0 kg Items Any item which only needs airing Weight of dry laundry 43 Programme chart Basket programme Max load for basket 3 5 kg Notes This programme may only be used with the Miele drying ba
21. AEFFELLELPEEIERTIUPEBRPETTEPESLTREEGEPELTERLFERELEERE 70 InStallatlon er ELE 71 Levelling th amp dryer cede ee aa 71 WENT ATOM x tefie eR ee NOE IE UE 72 Before moving the tumble dryer again e g when moving housegs 72 Additional installation requireMent cccccceeeeeeeeeeeeeceeaeceeeeeeeeeeeeeeeeneaanaeeeeeeeeees 73 Externally draining condensed water uuensessnsnnensennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 74 Installation conditions requiring a non return valve nnnesesssnnnnennnnnnnnnnnnn nn 74 Arranging the drain hose rrr eret t etta i erue kk ERE HERR Hue rau vines 75 EXatmiple8 ocio ation ree aunt ove anes oda VER aa un ne rinnen saa konnen 76 Contents Electrical connection ursrsursnnnnnnnnnnnnnnnnnnnannnannnnnnnnnnnnnnnnunnannnannnnnnnnnnnnnnnnnnn 78 Consumplion dala noter une 79 Technical data 5rd tette DEUM aris 81 Settings Menu nennen 82 Calling up settings sasssa 82 Language P RT t 82 NM Ie 83 Drying levels e o ted ie mE E xe terres Terre 83 Extended eool doWLis iiiter PE EE Eee PEE PE Feeds beh nat Erud cereer rere rere 83 Airways INGICATON vise ls la denne 83 sre zx EE 84 KEY DAC TOMG Mes ERE 84 7e alo O o1 ih 10 rS 84 Total COMSUMPTION Pe 84 PIN COJE tc 85 Display brightness uu 222nsuereennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnr en
22. EcoFeedback sensor You can view the actual amount of energy used Example Energy 2 0 kwh 0 1 kWh will be displayed if the energy consumption is very low The consumption will vary depending on the programme stage and residual moisture present If the door is opened or the tumble dryer has switched off automatically at the end of the programme the data will revert to the estimated consumption Total consumption setting Shows consumption data for the programme which has just been run and shows total energy consumption to date See Settings menu for more detailed information 23 1 Notes on correct laundry care Points to note regarding washed laundry When washing very heavily soiled items ensure that you use sufficient detergent and select a high temperature If in doubt wash the items several times Do not put soaking wet items into the tumble dryer Make sure your laundry is thoroughly spun before drying The higher the spin speed the greater the savings that can be made in energy and time during drying New dark coloured garments should be washed and dried separately from light coloured garments to avoid the danger of colours running and discolouring other garments or even plastic components in the dryer Dark coloured fibres can also settle on light coloured garments and vice versa Starched laundry can be dried in the tumble dryer To achieve the usual fin
23. Points to note regarding washed 18470 1 24 Preparing the laundry before drying uu su4s4444444444440nanannnnnnnnnnnnnnnnnnnnnannnnnn 24 Garment care label symbols sess nnne 25 Laundry care when drying in a tumble dryer seseeeseeeeeee 25 2 Loading the tumble dryer 4444444444440HHnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnnn nn 26 3 Selecting a programme and Starting it c cece cece eect cee ee eee eeteeeeeeeee 27 Selecting a programme unsuussennnannnnnnnnnnnnnnnnnnannnnnnnnnannnnnnnnannnnnnnnnannnnnnnnnannnnn nenn 27 Selecting any Extras or Delay start if required sesssssss 30 Starting the programme nn aa 30 4 Removing the laundry at the end of the programme 31 End of programme Anti crease unuusssennsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 31 Removing the lauridty iuit diri te itr i ri rede dir tua ux tas RE age 31 Dar c 32 Gentle tumble xr EHE RENE Eee e TUA IE rare 32 EreSheniuD BPRSSFFEUNEPTIERSPESTPEEFEUNSEEHELETTERLEETERBRESPEFITHETTETREFERNS III acess dI DELL 32 Auto load CONO iiec EEE coe epus berissesseccri coa busted uiisaste E 32 Anti CredSe eode anne a RUE aac aed 32 BUZZ MER 32 Favourite progra
24. See Changing the programme sequence Mixed items If you want to dry a mixed load you can select from a list of 19 different items The dryer will use the list to select the correct programme setting See Mixed items 29 3 Selecting a programme and starting it Selecting any Extras or Delay start if required Extras Gentle tumble zz Freshen up gt Auto load control Anti crease ez Buzzer ez m Press any button The button will light up when the Extra is selected An Extra can only be selected when the load indication has gone out in the display Not all Extras can be combined or can be selected deselected see Extras Please see Extras for further information Delay start m Press the Delay start button to select Delay start Please see Delay start for more information 30 Starting the programme m Press the flashing Start Stop button The Start Stop button will now light up constantly Drying and the programme duration will light up in the display When using programmes with a selectable drying level the drying level reached will light up later on instead of Drying The Perfect Dry indicator will only flash light up with programmes with selectable drying levels see also Operating the tumble dryer Cooling down will light up in the display shortly before the end of the programme The laundry will be c
25. See Cleaning and care Preparing the condensed water container for Steam smoothing 31 Extras Gentle tumble Freshen up es Auto load control ee Anti crease ee Buzzer zz Extras are switched on or off by pressing the appropriate button Not all Extras can be combined or can be selected deselected The button will light up when the Extra is selected Gentle tumble Delicate fabric with the KJ symbol on the care label e g acrylic garments is dried at a lower temperature The programme duration is longer Freshen up You can use the Freshen up Extra to help remove or reduce odours in clean dry or damp clothing The drying air is heated for a specific length of time After this the garments are aired to the Normal drying level without any more heat being added The drying level cannot be altered The Extra will be more effective if you dampen the garments a little beforehand use a fragrance flacon and reduce the load Please note that 32 odours will not be removed as effectively from parts of garments made of synthetic fibres Auto load control This Extra should be used if you only want to dry half the load given in the display and quoted in the Programme chart In this case by pressing this button you can both shorten and optimise the drying process Anti crease Depending on the programme selected the drum will continue to rotate in a special rhythm for
26. always ensured in order to separate the tumble dryer from the mains Connection of this appliance should comply with national and local safety regulations Do not connect the appliance via an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating The appliance should be connected up only by a qualified electrician in accordance with national and local safety regulations For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA The voltage rated load and plug rating are given on the data plate Please ensure that these match the household mains supply 78 Important The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter A or coloured red WARNING THIS APPLIANCE MUST BE
27. ause unnecessary Electri creasing ectrical and electronic appliances often contain materials which if Make sure the room temperature is handled or disposed of incorrectly not too high If there are other heat could be potentially hazardous to producing appliances in the room in human health and to the environment which the tumble dryer is located They are however essential for the make sure the room is well ventilated correct functioning of your appliance and switch the other appliances off if Therefore please do not dispose of possible ne PERETE NAN YOU HIVES Clean the fluff filters in the door opening after every drying cycle E Please dispose of it at your local community waste collection recycling centre 2 Contents Caring for the environment 4ussnn4nnnnnnnnnnnnnnnnnannnnnnnnnnn namen nannaa 2 Warning and Safety instructions essent 6 Operating the tumble dryer ssssssssssssseeeeeeeenenen nennen 17 Control Panel se ea an 17 DISDA y s ocior mnia den aed 18 Before using for the first time 21 EcOFeedDaCcK onore o ERE errprrrre errr reecer rte recente rere ttre 23 1 Notes on correct laundry Care c ccccccee eee e eee eeeeeeeeae eee ee eee eeeeeeeeeeaaeaees 24
28. calcified m Replace the spray jet optional accessory see end of this section m Only use condensed water Do not use tap water 64 Problem solving guide Bottom right grille A In general the cooling fins behind the grille on the bottom right do not need cleaning They should only be cleaned if the drying process is taking an exceptionally long time due to a very high level of dust or fluff in the room in which the dryer is located m First open the plinth filter panel on the left from underneath To remove the grille the catch behind it needs to be released using a spoon handle m Insert a spoon handle behind the grille in the middle m Press the spoon handle against the catch and lever the grille open m Remove the grille A Danger of injury Do not touch the cooling fins You could cut yourself A Use a vacuum cleaner with a dusting brush attached to clean the cooling fins Only pass the vacuum cleaner brush over them lightly without applying any pressure Take care not to bend the cooling fins out of shape or to damage them m Carefully vacuum up any visible fluff or dirt m Re insert the 3 hooks on the grille into the appropriate holes in the front of the dryer m Press the grille firmly back into position by pressing it in at the middle on the left 65 Problem solving guide Fluff filter in the condensed water container If you are experi
29. can select more items in the same way as described previously m Select more items if required Confirming a previously selected item will deselect it and the tick M will go out Displaying the items selected m You can view the items selected again Clearing a selection m You can delete all the items 36 Back gt m This returns you to tem selection Finishing selection save m Once you have made your selection and are ready to start drying confirm with the OK sensor The dryer has put together the optimum programme Caution Switching off the dryer will delete the tem selection list you have just made m You can still change the Drying level and select the Anti crease function or the Buzzer m Press the flashing Start Stop button to start the programme The list of items selected will be deleted at the end of the programme and the list will need to be selected again the next time you use this programme Delay start Selecting Delay start With Delay start you can delay the start of the programme by up to a maximum of 24 hours Please note that the time of day must be entered correctly for the Delay start function to work m After selecting the programme press the Delay start button Start at m The A sensor increases the time by 1 hour up to 24 hours The V sensor reduces the time m Confirm by touching the OK sensor The cursor will change from the hours to the minutes m Se
30. d care Emptying the condensed water container The condensed water is collected in the condensed water container Empty the condensed water container after every drying programme Empty the container will light up if the maximum level of the condensed water container is reached To delete Empty the container open and close the door with the dryer switched on A To prevent damaging the door and the front of the condensed water container when pulling the container out of the dryer always close the door completely m Pull out the condensed water container m Hold it at the front and towards the back and keep it in a horizontal position when carrying it 46 m Empty the container m Replace the container in the dryer A Condensed water should not be consumed It could lead to health problems for people and animals The condensed water can be used for the Steam smoothing programme The condensed water container must be filled to use this programme see the following section Cleaning and care Preparing the condensed water container for Steam smoothing A Condensed water which has collected in the condensed water container is directed into the drum in the Steam smoothing programme The condensed water container must therefore be filled with water up to at least the min marker The min marker is at the front left hand side of the container m Make use of the conde
31. d side moves with you as you scroll through the list to show you which option you have reached Identifying options selected There will always be one value selected This will have a tick V beside it The other values are deselected automatically Drying level i Slightly dry Hand iron amp 20 The V sensor highlights the next value and the A sensor highlights the previous value The OK sensor is used to confirm selection of the highlighted value If no selection is made the display will revert to the previous menu Setting numerical values 40h 0 40 2 30h The value which can be changed is highlighted in white The time is decreased with the V sensor and increased with the sensor The hours and then the minutes are confirmed with the OK sensor Leaving a sub menu Select Back to exit a sub menu Before using for the first time Removing the protective foil and stickers m Please remove the protective foil from the door any stickers from the front and the lid A Please do not remove any labels e g the data plate which are visible when you open the door After installing the tumble dryer A Before using the tumble dryer for the first time ensure that it is installed and connected to the electricity supply correctly If it has not been transported as described in Installation and connection then it must be left to stand for at least 1 hour before it is connecte
32. d to the electricity supply When the tumble dryer is switched on the welcome display Miele Willkommen will appear briefly Setting the language You will be asked to select the language you want for the display It is possible to change the language at any time via Settings deutsch V 00000 english AUS A english GB m You can scroll through the list by touching the V and sensors until the language you want is highlighted in the display m Confirm your choice of language by touching the OK sensor 21 Before using for the first time Setting the time of day if m Read 1 Notes on correct laundry necessary care and 2 Loading the tumble dryer Only touch the V sensor if you would like a 12 hour clock display m You can then load the tumble dryer and select a programme as Clock format described in 3 Selecting a 24 h clock i programme and starting it The procedure for using for the first time is completed when a programme lasting longer than one hour has been carried out in full 12 h clock m Confirm by touching the OK sensor Time m Touch the V sensor to decrease the hour or the sensor to increase it m Confirm the hour selected with the OK sensor Then set the minutes in the same way If you have selected 12 h clock you can then select am or pm The time of day will then appear at the top right hand side of the display each time you select a pr
33. e plinth filter are not cleaned A The fragrance filter must be removed before cleaning the fluff filter A Never lay the fragrance flacon down on any surface as the fragrance will run out A To prevent any fragrance running out of the flacon when not in use the fragrance flacon must only be stored in its original Only store the fragrance flacon in its packaging as illustrated original packaging m Clean the fluff filters and the plinth filter see Cleaning and care Afterwards refit the fragrance flacon When storing the fragrance flacon in its original packaging whilst you are not using it e g whilst cleaning the tumble dryer to prevent the fragrance running out do not store the packaging upright on its edge or upside down Store in a cool dry place Store away from direct sunlight 57 Problem solving guide Problem solving guide With the help of the following notes minor faults in the performance of the appliance some of which may result from incorrect operation can be put right without contacting Miele Please note that a call out charge will be applied to service visits where the problem could have been rectified as described in these operating instructions A Repair work to electrical appliances should only be carried out by an authorised Miele service technician Repairs and other work by unqualified persons could be dangerous Miele cannot be held liable
34. e rubber seal when doing this m Check whether the cooling fins are blocked with fluff as follows m Carefully vacuum up any visible fluff or dirt 51 Cleaning and care Replacing the plinth filter A The dryer can only be operated with the plinth filter fitted correctly and the heat exchanger access panel closed The access panel must be closed correctly to ensure that water cannot leak from the condenser system and to ensure that the dryer functions efficiently m Fit the filter back on the handle Make sure it is the correct way round To ensure that the filter is positioned correctly in the front of the heat exchanger unit m First insert the handle with the plinth filter attached over the two guide pins The word Miele on the handle must be the correct way up m Push the plinth filter in completely The act of pushing in the plinth filter will also push in the right hand guide pin m Close the heat exchanger access panel 52 Cleaning and care Tumble dryer A Disconnect the machine from the mains electricity supply A Do not use solvents abrasive cleaners glass cleaners or all purpose cleaners These could damage plastic surfaces and other parts m Clean the tumble dryer with a slightly damp cloth and a mild non abrasive cleaning agent or a solution of washing up liquid and water m Clean the seal around the inside of the door with a damp cloth m Dry all parts
35. e tool to the spray jet m Turn the tool anti clockwise to unscrew the spray jet m Insert the new spray jet in the tool m Turn the tool clockwise to screw the spray jet securely in position 67 After sales service Repairs In the event of any faults which you cannot remedy yourself please contact Miele Please note however that a call out charge will be applied to service visits where the problem could have been rectified as described in these operating instructions The contact details for Miele are given at the back of these instructions When contacting Miele please quote the model and serial numbers both of which are located on the data plate visible when the door is open 68 Optional accessories Optional accessories for this tumble dryer are available from Miele see contact details at the back of these instructions Miele www miele shop com You also can order these and many other useful products via the internet depending on country Drying basket The drying basket is suspended in the drum and does not rotate with the drum This enables items which must not be subjected to mechanical action to be dried or aired Fragrance flacon A fragrance flacon can be used in your tumble dryer to add a pleasant fragrance to your laundry Warranty The manufacturer s warranty for this appliance is 2 years See the warranty card supplied with the tumble dryer for f
36. encing problems running the Steam smoothing programme the fluff filter at the end of the hose which is connected to the rubber seal in the condensed water container could be blocked m Pull out the condensed water container m Remove the spout by holding the side lug and pulling upwards To avoid detaching the hose be careful not to tug on it 66 m Guide the end of the hose through the opening and hold it securely with one hand m Use your other hand to pull the fluff filter off the hose Rinse the fluff filter with a jet of water until all the fluff has been removed m Refit the cleaned fluff filter onto the hose m Now feed the hose with its fluff filter attached into the condensed water container m Replace the spout in the condensed water container Make sure it is the correct way round see the illustration Problem solving guide Steam smoothing spray jet A Limescale deposits will impair the spray jet In this case the spray jet must be removed and replaced with a new one see Optional accessories The spray jet can only be replaced using the special tool supplied with the new spray jet A Do not use any other tool as this would damage the spray jet or the dryer A Steam smoothing must never be used without the spray jet fitted and screwed in correctly m Open the door of the tumble dryer The spray jet is located in the top left of the door opening m Attach th
37. er components e g the fluff filter gt If fragrance which has run out of a flacon should come in contact with the skin wash the skin thoroughly with soap and water come in contact with the eyes rinse the eyes with clean water for at least 15 minutes be swallowed rinse out the mouth thoroughly with clean water Seek medical advice in the case of contact with the eyes or if fragrance has been swallowed gt If fragrance which has run out of a flacon comes in contact with clothing change the clothing immediately Wash the clothing or any cloths used for mopping up fragrance thoroughly with plenty of water and detergent There is the risk of fire or damage to the tumble dryer if the following instructions are not observed Never refill a flacon with fragrance Never use a faulty fragrance flacon Dispose of an empty fragrance flacon with the household waste and never use it for any other purpose gt Please also observe the information supplied with the fragrance flacon 15 Warning and Safety instructions Accessories Only use genuine Miele spare parts and accessories with this appliance If spare parts or accessories from other manufacturers are used this will invalidate the warranty and Miele cannot accept liability A Miele tumble dryer can be stacked on top of a Miele washing machine using the appropriate stacking kit available as an optional accessory Please make sure you order the
38. ers Germany Miele amp Cie KG Carl Miele Stra e 29 33332 G tersloh Federal Republic of Germany TKR 450 WP C en AU NZ M Nr 10 207 610 00
39. h filter when Clean out airways lights up To delete Clean out airways Switch the dryer off and back on again or confirm with OK Removing the plinth filter m Press the round indented area on the heat exchanger access panel to open it The panel will spring open m Pull the plinth filter out by the handle 50 Removing the plinth filter will cause the right hand guide pin in the dryer to come out This pin ensures that the heat exchanger access panel can only be closed if the plinth filter is inserted the right way round Cleaning the plinth filter Pull the handle out of the plinth filter m Clean the filter thoroughly under running water m Squeeze the water out of the plinth filter thoroughly A The plinth filter must not be replaced dripping wet as this can cause a fault m Use a damp cloth to remove any fluff from the handle Cleaning and care Cleaning the plinth filter panel Checking the heat exchanger unit A Danger of injury Do not touch the cooling fins You could cut yourself m Look to see if fluff has accumulated If there is visible soiling A Clean using a vacuum cleaner with a dusting brush attached Carefully pass the vacuum cleaner brush over the heat exchanger cooling fins without applying any pressure Otherwise the cooling fins could be bent out of shape or become damaged m Use a damp cloth to remove any fluff Make sure that you do not damage th
40. he end of the hose is immersed in water Connection to a sink drain outlet Connection to a drainage system already in use by another appliance e g a dishwasher or washing machine A The non return valve has to be fitted with the arrow pointing in the direction of flow Otherwise water will not drain out of the appliance Installation and connection Arranging the drain hose A Do not pull on the drain hose and do not stretch it or allow it to become kinked This could damage the hose There will be a small amount of residual water left in the drain hose Have a container ready to collect this m Guide the hose to the right or left side of the dryer as required f you are guiding it to the right you can fit the hose into the groove Leave the hose in the lower holder to prevent it from being kinked inadvertently m Pull the drain hose off its connection m Unwind the hose and pull it carefully out of the holders m Allow any residual water to run into the container 75 Installation and connection Examples Direct connection to a sink drain outlet Drainage into a sink or floor gully Use the hose holder to prevent the drain hose from becoming kinked m Remove the following from the back of the dryer at the top Adapter 1 and hose clip 3 behind it m Press the small catches on the left m Connect the drain hose as described and right of the hose
41. installed behind a lockable door a sliding door or a door with a hinge on the opposite side to that of the tumble dryer in such a way that a full opening of the tumble dryer door is restricted Levelling the dryer A Make sure the dryer door can be The screw feet can be adjusted to opened without hindrance after compensate for any unevenness in the installation floor The appliance must stand perfectly level to ensure safe and proper operation 71 Installation and connection Ventilation Before moving the tumble dryer again e g when moving houses A The cool air intake at the front of the dryer must not be blocked or covered This would hinder a sufficient intake of cool air for the heat exchanger After each use a small quantity of condensed water will collect in the area of the pump This water can run out if the tumble dryer is tipped up when it is being moved Recommendation Run the Warm air programme for N Do not block the gap between approximately 1 minute before moving the bottom of the tumble dryer and the tumble dryer Any remaining the floor with plinth facings deep condensed water will then be fed into pile carpet etc This would hinder a the condensed water container which sufficient flow of air to the tumble can then be emptied or out through the dryer drain hose Adequate ventilation has to be provided to avoid the back flow of gases into the room from appliances burni
42. ish double the amount of starch should be used Preparing the laundry before drying A Make sure that any objects e g detergent dosing balls lighters etc have been removed from the laundry They could melt or explode and cause damage to the tumble dryer or the laundry 24 See Warning and Safety instructions for further information Loading or using the tumble dryer incorrectly could cause a fire Sort the laundry according to the type of fibre and weave size garment care label symbol and the drying level required Check the seams of padded or down filled items to prevent the risk of fillings coming out These could catch fire when being dried Disentangle the laundry Tie together textile belts and apron ties Fasten duvet covers and pillow cases to prevent small items from being trapped inside them hooks and eyes Sew in or remove underwiring from bras Leave jackets open and undo any long zips so that textiles dry evenly Minimum iron fabrics tend to crease more the greater the load This is also the case for garments made from very fine weave fabric such as shirts or blouses If necessary reduce the size of the load for these types of fabric 1 Notes on correct laundry care Garment care label symbols Drying Normal Higher temperature Reduced temperature Select Gentle tumble for delicate textiles Ed Do not tumble dry
43. lps prevent creasing if laundry is not going to be removed immediately You can reduce the duration of the anti crease phase Options 1hr 2 hr factory default Delay start With the Delay start function you can Delay the time at which the programme should start see Delay start You can choose whether you want the display to prompt you to enter the time at which the programme should begin Start at or the time at which it should end Finish at Options Start at factory default Finish at Miele Australia Pty Ltd ACN 005 635 398 ABN 96 005 635 398 Miele Center and Head Office Melbourne 1 Gilbert Park Drive Knoxfield VIC 3180 Miele Center and Office Melbourne 206 210 Coventry Street South Melbourne VIC 3205 Miele Center and Office Sydney 3 Skyline Place Frenchs Forest NSW 2086 Miele Center and Office Brisbane 39 Harvey Street North Eagle Farm QLD 4009 Miele Center and Office Adelaide 83 85 Sir Donald Bradman Drive Hilton SA 5033 Miele Center and Office Perth 205 207 Stirling Highway Claremont WA 6010 1300 4 MIELE 1300 464 353 www miele com au Miele www miele shop com Miele New Zealand Limited IRD 98 463 631 Head Office Level 2 10 College Hill Freemans Bay Auckland 1011 Miele Center Auckland 8 College Hill Freemans Bay Auckland 1011 Telephone 0800 4 MIELE 0800 464 353 www miele co nz Miele Global Headquart
44. luff filters gm from the perforated laundry deflector m Push the upper fluff filter back into position until it clicks m Pull the upper fluff filter forwards to remove it m Close the door If there is a great deal of compacted fluff carry out the following procedure 48 Cleaning and care Cleaning the fluff filters and air flow openings thoroughly If the drying duration has become longer or the surface of the filters is visibly compacted with fluff you should carry out the following cleaning procedure A If using a fragrance flacon make sure you remove it beforehand m Pull the upper fluff filter forwards to remove it m Turn the yellow dial on the lower fluff filter in the direction of the arrow until you hear it click m Hold the dial and pull the fluff filter forwards to remove it m Use a vacuum cleaner with a long crevice nozzle attached to remove any visible fluff from the upper air flow openings Cleaning the fluff filters with water m Flush the fluff filters through with warm running water m Shake the fluff filters thoroughly and then dry them carefully A Ensure the filters are dry before replacing them Wet filters could cause operational faults m Push the lower fluff filter in completely and lock it with the yellow dial m Push the upper fluff filter in completely m Close the door 49 Cleaning and care Plinth filter Only clean the plint
45. mmes 4444444444400nannannnnnnnnnnnnnnnnnannannnnnnnnnnnnnnnnnnnnnnnnnn 34 Mixed items 00 cece cence ee ee eee ee eee eee aaa ae ee tenth nsn ea nnns e aaa ae ae eee sees n ensi nnn tnn nns 36 Delay starb o e eer rere cesta er ere re ere MEI DES 37 Programme chart 5 d eror siete PERITI EE He Herve Eus 38 Changing the programme sequence ussssssssnnnnnnnnnnnnnnnnannnnnnnnnnnnnnnnnnn 45 Contents Cleaning and care 46 Emptying the condensed water container uuussssssnsnenseennnnnnnnnnnnnnnnnnnnnnnnnnn nennen 46 Preparing the condensed water container for Steam SMOOTHING 47 nni MILL e 48 Removing visible TlUff iion ee 48 Cleaning the fluff filters and air flow openings thoroughly 49 Plinthifiliar aereo rr een voce RAE ERR Re EE YE DE ERE EK Un RARE 50 Removing the plinth filter eee eee ence eee eeeeaeeeeeeeeaaeeeeeeeaaaeeeeeeeaaeeeeeeeeaaeeeeeee 50 Cleaning the plinth filter iic ei en era ee 50 Cleaning the plinth filter panel nuunusssnsenannnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen 51 Checking the heat exchanger unit uusssrsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen 51 R placing the plinthifilter
46. n doubt wash the items several times Oil affected items can ignite spontaneously especially when exposed to heat sources such as in a tumble dryer The items become warm causing an oxidation reaction in the oil Oxidation creates heat If the heat cannot escape the items can become hot enough to catch fire Piling stacking or storing oil affected items can prevent heat from escaping and so create a fire hazard If it is unavoidable that fabrics contaminated with vegetable or cooking oil or hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent this will reduce but not eliminate the hazard gt Remove all items from pockets e g lighters matches 12 Warning and Safety instructions gt Warning Ensure that you always wait until the end of the programme before removing the laundry If the drying programme is stopped prematurely remove the laundry immediately and hang it up or spread it out to cool it down gt Fabric softener and similar products must be used according to the instructions on the manufacturer s packaging To prevent the risk of fire the following textiles must not be dried in this tumble dryer tems which have been cleaned using chemicals e g professional dry cleaning agents Fabrics which contain a large proportion of rubber foam rubber or rubber like materials For example products made from latex foam rubber shower
47. n risk and follow the instructions provided on the packaging Any other applications may be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation Warning and Safety instructions This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it by a person responsible for their safety Safety with children gt Young children must not be allowed to use this appliance Older children may only use the appliance when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse Children must not be allowed to clean or maintain the tumble dryer unsupervised Please supervise children in the vicinity of the tumble dryer and do not let them play with it Warning and Safety instructions Technical safety Before setting up the tumble dryer check it for any externally visible damage Do not install or use a damaged tumble dryer gt Before connecting the tumble dryer ensure that the connection data on the data plate fuse rating voltage and frequency matches the mains electricity supply If in any doubt consult a qualified electrician gt The electrical safety of this tumble dryer can only be guaranteed when correctly earthed I
48. ng other fuels including open fires Air which is taken in to cool the heat exchanger is then blown back out of the dryer and warms up the air in the room It is therefore very important to ensure adequate ventilation e 9 by opening a window Otherwise drying durations may be longer increased energy requirement 72 Installation and connection Additional installation requirements A The dryer should not be installed next to a refrigeration appliance The warm air expelled from the rear of the dryer would increase the temperature around the refrigeration appliance s heat exchanger causing the compressor to run continuously If it is not possible to install the dryer anywhere else then the refrigeration appliance must be sealed off from the dryer It is very important to avoid a build up of heat The warm air which is expelled from the dryer must be able to dissipate Warm air which cannot dissipate could cause a fault A build up of heat can be avoided by Adjusting the screw feet so that there is a gap of at least 20 mm between the floor and the bottom of the dryer Creating a gap for the dryer in the kitchen furniture plinth facing Creating ventilation gaps in the kitchen unit Suitable for pushing under a worktop This tumble dryer is suitable for pushing under a worktop The appliance lid must not be removed The electrical socket must be located in an accessible position
49. nnn nen nnns 85 Display switch off Status iieri eiii Lone een ei tenenda na 85 Appliance Switeh off status neueren nennen sera RAE 86 Mime 86 AB Scredseiebierdeensiereiiresstesitie n reip ise eec ei mer EEE 86 Delay Start M HH 86 Warning and Safety instructions LL P Itis essential to read these instructions This tumble dryer complies with current local and national safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the tumble dryer please read these instructions carefully before using it for the first time They contain important information on its safety installation use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Correct application This tumble dryer is designed for domestic use and for use in similar environments by guests in hotel or motel rooms bed amp breakfasts and other typical living quarters This does not include common shared facilities or commercial facilities within hotels motels or bed amp breakfasts This tumble dryer is not suitable for outdoor use gt It must only be used to dry items which have been washed in a water solution and which are marked on the manufacturer s care label as being suitable for tumble drying If using dry cleaning kits do so at your ow
50. nsed water which collects during the drying process If the condensed water container is empty m You can fill the condensed water container with commercially available condensed water ironing water You should only use tap water in exceptional circumstances If tap water is used frequently however the Steam smoothing spray jet in the door opening can become calcified 1 spout 2 rubber seal m Pour the water in through the rings of the spout 1 A Only use clean water The water must not contain any fragrance detergent or other substances Check the rubber seal from time to time If tap water is used frequently white limescale deposits can build up on the rubber seal 2 m Use a damp cloth to carefully remove any limescale deposits from the rubber seal 2 m After cleaning the rubber seal push the condensed water container fully into the dryer 47 Cleaning and care Fluff filters This tumble dryer has 2 fluff filters in the door opening the upper and lower fluff filters trap fluff produced during the drying process Removing visible fluff Remove any fluff after every drying cycle Useful tip You can also use a vacuum cleaner so that you can remove the fluff m Remove the fluff see arrows without touching it m Open the door A You must remove the fragrance flacon if present beforehand see Fragrance flacon m from the surfaces of all the f
51. ogramme Completing the procedure for using for the first time outlined in these instructions i Information s in the s booklet for setting up the machine for the first time m Confirm by touching the OK sensor 22 EcoFeedback You can use the EcoFeedback sensor to call up information about the energy consumption of your dryer Touching the EcoFeedback sensor will call up two types of information Anestimate of the consumption before the programme begins The energy consumption during the programme The EcoFeedback sensor will light up and information will appear in the display Both will go out automatically a few seconds later or alternatively they can be confirmed with OK At the end of the programme before opening the door you can also call up the following in the display The energy consumption The degree of soiling of the fluff filters and the plinth filter 0 light 50 medium 100 heavy Accumulating fluff and soiling will cause the programme duration to increase which in turn will increase energy consumption 1 Estimate m After selecting a programme touch the EcoFeedback sensor For a few seconds bars which indicate the estimated consumption will be shown Energy BEBBE___ The more bars visible the higher the energy consumption The estimate will vary depending on the programme and any options selected 2 Actual consumption m Touch the
52. ondensed water pump is running Automatic plus Max load 5 0 kg Normal plus Normal Slightly dry Hand iron Hand iron 56 Items Mixed loads of garments suitable for the Cottons and Minimum iron programmes Sort according to colour Weight of dry laundry 41 Programme chart Delicates Max load 2 5 kg Normal plus Normal Slightly dry Hand iron Hand iron 55 Items Delicate items with the KJ symbol on the care label made of synthetic fibres easy care cotton or blended fabric e g shirts blouses lingerie and evening wear with sequins and beading Notes Reducing the load will reduce creasing Silks handcare Max load 1 0 kg Items Silk garments which are suitable for drying in the tumble dryer e g blouses and shirts Notes This programme reduces creasing Items are not dried completely by this programme Remove garments as soon as the programme has finished Sportswear Max load 3 0 kg Normal plus Normal Slightly dry Hand iron Hand iron 56 Items Sportswear which is suitable for drying in a tumble dryer Pillows 1 2 pillows up to 80 x 40 cm 1 pillow up to 80 x 80 cm Normal Items Pillows suitable for drying in a tumble dryer with feather down or synthetic fillings Note Please observe the instructions on the care label Pillows can still feel damp after being dried You can use this programme several times until
53. ooled down however the programme is not yet finished 4 Removing the laundry at the end of the programme End of programme Anti crease At the end of the programme Anti crease if selected or Finish will light up The Start Stop button will no longer be lit up To save energy 10 minutes after the end of the programme the Start Stop button will begin to flash slowly and the display will go out The dryer will switch off automatically 15 minutes after the end of the anti crease phase with programmes without an anti crease phase it will switch off 15 minutes after the end of the programme Removing the laundry A Never open the door before the drying process has finished m Reach under the door grip and pull the door open m Remove the laundry Check that all items have been removed from the drum If items are left in the dryer they could be damaged by overdrying when the dryer is next used If the dryer is switched on at the mains and the door is opened the drum lighting will come on It will go out a few minutes later to save energy m f the dryer is still switched on switch it off with the D button A buzzer will sound m Remove the fluff from the 2 fluff filters in the door opening see Cleaning and care Fluff filters m Shut the door with a gentle swing m Empty the condensed water container Useful tip The condensed water can be used for the Steam smoothing programme
54. play The total consumption is displayed in kWh Reset function The total consumption to date will be deleted with the Reset option Settings menu PIN Code Display switch off status The code prevents your machine being used without your knowledge Options Activate The code is 250 and can be activated When the code has been activated you have to enter the code after switching the dryer on Otherwise the dryer cannot be operated Deactivate For using the dryer without entering the code This only appears if the code has been activated previously Change You can enter a code of your own A Important Make a note of your new code If you forget the code the dryer will need to be unlocked by a Miele service technician Display brightness The brightness of the display can be altered The setting selected is shown in a bar chart Factory default a medium setting Darker BZ Z 2 Brighter BEBE EE N You will see the brightness change as the setting is selected To save energy the display and buttons will go out after 10 minutes and the Start Stop button will flash slowly You can alter this setting Options On factory default The display will go out after 10 minutes if a programme is not selected after the dryer has been switched on during the current programme after the end of a programme On not in current
55. programme The display will go out as described above but will remain on while the programme is running Off The display will remain on i e it will never go out You can switch the display and buttons back on again by pressing any button 85 Settings menu Appliance switch off status Anti crease To save energy the dryer will switch off automatically after 15 minutes You can lengthen or shorten the time The dryer will switch off automatically after 10 15 or 20 minutes if no further selection is made after switching the dryer on at the end of the anti crease phase after a programme without an anti crease phase has finished However there is no automatic switch off in the event of a fault Options after 10 minutes after 15 minutes factory default after 20 minutes Memory drying level or options for a selected programme The duration selected for a timed drying programme will also be stored in memory These settings will then appear the next time the programme is chosen The electronics will store in memory a Options Off the machine is delivered with this option selected as standard On Exception The Cottons 4 programme will remain unchanged 86 If you have pressed the Anti crease button the drum will continue to rotate in a special anti crease rhythm for a maximum of 2 hours after the end of the drying process This he
56. red cotton fabric such as towelling jerseywear T shirts underwear workwear covers flannelette bed linen and baby clothes Notes Select Extra dry for multi layered and very thick fabrics Do not use Extra dry for jersey fabrics e g T shirts underwear as they have a tendency to shrink Items Note Hand iron 6 Hand iron 80 Machine iron Cotton or linen fabric requiring further processing e g table linen bed linen starched laundry To prevent laundry from drying out it should be rolled up until you are ready for ironing Weight of dry laundry 38 Programme chart Minimum iron Max load 4 0 kg Normal plus Normal Slightly dry Hand iron Hand iron 55 Items Minimum iron items made of cotton synthetic or mixed fibre e g tops dresses shirts blouses skirts trousers and table linen Woollens handcare Max load 2 0 kg Items Woollen garments and fabric containing wool blends e g pullovers jackets Notes Wool and wool blend items are only fluffed up they are not dried completely Remove garments as soon as the programme has finished Denim Max load 3 0 kg Normal plus Normal Slightly dry Hand iron Hand iron 56 Items Denim garments e g jeans jackets skirts shirts Shirts Max load 2 0 kg Normal plus Normal Slightly dry Hand iron Hand iron 64 Items Shirts and blouses Weight of dry laundr
57. s handcare Cottons Favourites Minimum iron Mixed items Woollens Express handcare Denim Gentle smoothing Denim Gentle smoothing Shirts Steam smoothing Shirts J Steam smoothing m Turn the programme selector Different programmes and setting options will light up in the display depending on the position of the Further programmes POSITI 90000 Automatic plus When a programme is selected the Delicates maximum load weight of dry laundry Silks handcare possible for the programme will appear in the display for a few m Touch the V or A sensor to scroll seconds through the list until the programme You can confirm with OK or wait until you want appears in the display the preset drying level or programme duration lights up If you think you have loaded too much laundry remove a few items m Confirm by touching the OK sensor 27 3 Selecting a programme and starting it Programmes with drying levels Cottons Minimum iron Delicates Denim Shirts Express Gentle smoothing Steam smoothing Automatic plus Sportswear Outerwear The drying level can be altered after selecting one of these programmes The duration and the preset drying level will be displayed in addition to the programme name Cottons Duration A S f h Normal m Press the Drying level button Drying level Normal i S Slightl
58. s the programme used in energy consumption tests to AS NZS 2442 Refer to www energyrating gov au website for consumption data The consumption data shown in the EcoFeedback display can vary from the consumption data quoted here The variations arise from the way the data is measured in the dryer For example the programme duration may vary depending on the residual moisture present in the laundry and the type of fabric which will affect the energy requirement 80 Technical data Height Width Depth Depth with door open Height for building under Width for building under Depth for building under Suitable for pushing under a worktop Suitable for stacking Weight Drum volume Maximum capacity Capacity of condensed water container Drain hose length Maximum delivery head Maximum drain hose length Length of connection cable Voltage Rated load Fuse rating Test certificates awarded Energy consumption LEDs 850 mm 596 mm 636 mm 1054 mm 850 mm 5 5 mm 600 mm 600 mm Yes Yes Approx 62 kg 1201 8 0 kg weight of dry laundry 4 8 1 60 m 1 50 m 4 00 m 2 00 m See data plate See data plate See data plate See data plate See Consumption data Class 1 81 Settings menu Calling up settings The Settings menu is used to alter the dryer s electronics to suit different requirements Settings can be altered at any time Opening the Settings menu m Switch the tumble dryer
59. sket optional accessory fitted Use this programme to dry or air items which are suitable for drying in a tumble dryer but which are not suitable for drying using mechanical action Itis essential to observe the operating instructions for the drying basket Fabric See the operating instructions supplied with the drying basket type ltems Cottons hygiene Max load 4 0 kg Normal Items Cottons and linen fabrics which will be in direct contact with the skin e g underwear nappies towelling bed linen pillow and mattress covers Note The temperature is held constant for a longer period of time longer temperature holding time to deactivate micro organisms e g bacteria or house dust mites and also to reduce the number of allergens in the laundry To ensure that micro organisms are deactivated do not interrupt the programme Weight of dry laundry 44 Changing the programme sequence You cannot change to another programme once a programme has started this prevents unintentional alterations If you move the programme selector Programme cannot be changed will light up in the display until you move the programme selector back to the original programme You will need to cancel the current programme before you can select a new one Once a programme has started cancelling the programme and then selecting a new programme m Press the Start S
60. ss eek 52 Fragrance flacon oot e eee a eet are reer desse temu uetus aai 54 Inserting a fragrance flacon 54 Replacing the fragrance flacon cccceeeeeteceeeeeenneeeeeeeaaeeeeeeeaaeeeeeeeaaaeeeeeeenaeeeeeneeaas 56 Problem solving guide essere nennen nenne 58 Problem SOWING guide incur tri rtt decreti d tra bea n cre Ee aedes ad edicta sa Ea gis 58 Messages in the display en ne ne ea 58 Unsatisfactory drying results uuusresssnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 61 Other proDleriss eene roto E a a i eU isa m scd eru ener rere 62 Bottom right grille nn een ee 65 Fluff filter in the condensed water container uun eennsersessnnnnennnnnnnnnnnnnnnnnnnnnnn nn 66 Steam smoothing spray jet 44usrsnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnns 67 After sales semice u 2 etr i d rr o RR Read a Ra FR E E an is 68 Repais HH 68 Optional accessories eaae a a a e aa ecu ESSEN ESEE 68 E E E E E A A E 68 Installation and connection 4444444Hnn nennen ee nnnnnnnnnnnnnnnnnnnnnnnnnnn ern 69 Fr nt VIEW ande inne ae aaa naar aan a nass A ER 69 Rear VIEW yc cts sca decetetcceecueves n even suyuny coucavueesatex counveeauecauudacacederestavesenvecatetes 70 Transporting 1o1 o 47 1GPPEPREREHEPRELTEFAEEFRPEFFEEEFELEPP
61. st not be installed and operated in mobile installations e g on a ship gt Do not make any alterations to the tumble dryer unless authorised to do so by Miele Heat pump technology and refrigerant The heat pump in this tumble dryer uses a refrigerant which is condensed by the compressor and led in a closed circuit through the heat exchanger unit where heat exchange with the circulating drying air takes place The humming noises caused by the heat pump are normal and do not impair the efficient functioning of the dryer The refrigerant is not flammable or explosive In general it is not necessary to leave the dryer standing for any length of time before it is connected to the mains provided it has been transported and installed correctly Warning and Safety instructions gt Please observe the instructions in Installation and connection and Technical data gt The accessibility of the plug must be always ensured in order to separate the tumble dryer from the mains gt Do not block the gap between the bottom of the tumble dryer and the floor with plinth facings deep pile carpet etc This would hinder a sufficient flow of air to the tumble dryer Make sure the dryer door can be opened without hindrance after installation 10 Warning and Safety instructions Correct use READ THE INSTRUCTIONS N Caution Risk of fire To avoid the possible danger of fire please read these warnings
62. t is essential that this standard safety requirement is met If in any doubt please have the household wiring system tested by a qualified electrician Miele cannot be held liable for the consequences of an inadequate earthing system e g electric shock Reliable and safe operation of this tumble dryer can only be assured if it has been connected to the mains electricity supply Do not connect the tumble dryer to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating gt If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger Unauthorised repairs could result in unforeseen dangers for the user for which Miele cannot accept liability Repairs should only be undertaken by a Miele authorised service technician otherwise any subsequent damage will not be covered by the warranty gt Faulty components must only be replaced by genuine Miele spare parts Miele can only guarantee the safety of the appliance when Miele replacement parts are used Warning and Safety instructions gt In the event of a fault or for cleaning purposes the tumble dryer is only completely isolated from the electricity supply when itis switched off at the wall socket and the plug is withdrawn or itis switched off at the mains circuit breaker This tumble dryer mu
63. t the minutes in the same way The minutes are selected in 15 minute increments m Confirm by touching the OK sensor Changing Delay start if necessary m Press the Delay start button m Select Change the time and change it Deleting Delay start if necessary m Press the Delay start button m Select Cancel the time and confirm this with OK Starting Delay start m Press the Start Stop button The time at which the programme will start automatically will appear in the display The drum will turn briefly every hour until the start of the programme to reduce creasing Changing Delay start after it has started counting down m Press the Delay start button You can either start the programme immediately or change the time m To do this touch the A or V sensor m Confirm by touching the OK sensor Adding or removing laundry after a programme has started m You can open the door to add remove laundry m Press the Start Stop button so that the Delay start time continues to count down Cancelling Delay start m Press the Start Stop button m Confirm Cancel Delay start with OK 37 Programme chart Cottons lt _ Max load 8 0 kg Items Cotton items such as those described under Cottons Normal with normal residual moisture Note Items are dried to a Normal level only Cottons Max load 8 0 kg Extra dry Normal plus Normal Slightly dry Items Single and multi laye
64. te the room thoroughly Detergent residues hair and fine fluff can clog the filters m Clean the fluff filters and the plinth filter m Remove any visible fluff bottom left from behind the panel in the heat exchanger cavity see Cleaning and care from the cooling fins behind the grille bottom right See the end of this section The cool air intake bottom right grille is blocked m Move any objects such as a laundry basket away from the dryer The fluff filters and the plinth filter were wet when replaced m The fluff filters and the plinth filter must be dry The laundry is too damp m Spin using a higher spin speed in the washing machine The tumble dryer has been overloaded m Do not exceed the maximum load for the programme selected Metallic components e g zippers have prevented the dryer from registering the correct moisture level m Open the zippers next time m If the problem recurs dry these items using the Warm air timed drying programme Before starting another programme m Switch the dryer off and then on again 62 Problem solving guide Problem Possible cause and remedy There are humming noises This is not a fault The compressor heat pump is operating or you have selected the Steam smoothing programme m No action is required These noises are quite normal and can be heard when the compressor or the condensed water pump is
65. the plinth filter Clean the airways m Clean the area underneath the plinth filter m Clean the heat exchanger To switch off the messages m Switch the dryer off and back on again CIJ Empty the container Empty the container or check the drain hose lights up after a programme is cancelled The condensed water container is full or there is a kink in the drain hose m Empty out the condensed water container m Check the drain hose To switch off the message m Open and close the door while the dryer is switched on or switch the dryer off and back on again i Information Fill condensate container i Information Please open and close the door This is to remind you that water is taken from the condensed water container when the Steam smoothing programme is being used The condensed water container must be filled with water to at least the min marker m Confirm with OK This it to remind you to load the laundry when the Steam smoothing programme is selected m Load the laundry in the drum 59 Problem solving guide Problem Possible cause and remedy Extra cooling 60 The programme has finished but the laundry has not yet cooled down m Either remove the laundry and spread it out to cool down or leave it in the tumble dryer to cool down during the cooling phase Problem solving guide Unsatisfactory drying results Problem Possible cause and remedy
66. to ensure a precise drying result The Perfect Dry indicator Will flash after the programme has started and go out when the programme duration appears in the display Will light up again when the selected drying level is reached and remain on until the end of the programme Will remain dark with the following programmes Woollens handcare Silks handcare Cool air Warm air Basket programme Estimated time remaining After the programme has started the estimated programme duration will appear in the display in hours and minutes The programme duration displayed for programmes with a selectable drying level may vary or jump The following factors among others affect the programme duration displayed the quantity of the laundry the type of fabric and the residual moisture in the laundry The electronics continually access conditions in the appliance and adjust the programme duration with increasing accuracy 19 Operating the tumble dryer Examples on how to operate the appliance Scrolling through a list The option which can be selected will be highlighted with a white bar Further programmes Delicates Touching the V sensor scrolls down the list to the next option and touching the sensor scrolls up the list to the next option The OK sensor is used to confirm your selection A dotted line will appear at the beginning and the end of a list The bar on the right han
67. top button Confirm Cancel programme with the OK sensor Cooling down will light up in the display depending on the drying duration and the drying temperature reached Wait until Finish lights up in the display or press the Start Stop button again until Finish lights up m Press the D button to switch the dryer off m Press the D button to switch the dryer on m Select and start a new programme straight away Saving the programme as a Favourite m Press the Start Stop button m Select and confirm Save programme You can save this programme under Favourites See Favourites 2 Entering a name Adding or removing laundry after a programme has started m Press the Start Stop button m Select Cancel programme m Confirm by touching the OK sensor Cooling down will light up in the display depending on the drying duration and the drying temperature reached Wait until Finish lights up in the display or press the Start Stop button again until Finish lights up A Danger of burning Do not touch the back of the drum when adding or removing items The drum and the items can be very hot m Add or remove items m Close the door To continue with the programme change the drying level first of all if necessary m Press the Start Stop button Programme duration Altering the programme sequence can cause the programme duration shown in the display to be adjusted 45 Cleaning an
68. up Auto load control m Turn the programme selector to Favourites m Select and confirm an option 1 Creating a Favourite programme Extras Favourite programmes M Gentle plus L O Freshen up Auto load control A M will appear next to the Extra and m Confirm Create with the OK sensor the following will light up in the display m Touch the V or sensor to highlight Extras the programme you want m Confirm with the OK sensor m If appropriate select a drying level or duration with the V or sensor and confirm with OK Change Add to selection m Confirm Change Add to selection if Extras A a you want to select an additional Select Extras option Continue without Extras Finish selection m You must confirm Finish selection once you have selected the options you want m Select Select Extras or Continue without Extras Display selection m You can view your selection again Clear selection m You can delete the options 34 Favourite programmes Summary Accept Cottons Normal m Select Accept and confirm 2 Entering aname You can enter a name of up to 10 characters Enter name _ wa ft OY M BCD m Touch the V or sensor to move along the characters until the character you want is highlighted m Confirm selection of each character by touching the OK sensor Characters can also be saved deleted or changed by selecting one of the symbols
69. up to 2 hours at the end of the programme to reduce creasing if you do not wish to remove the laundry immediately Buzzer A buzzer four beeps at intervals for a maximum of 1 hour will sound to let you know that the programme has finished The continuous buzzer which sounds when there is a fault is not dependent on the setting for the buzzer at the end of the programme Extras The following Extras can be selected in addition to the programmes Gentle Freshen Auto load Anti Buzzer tumble up control crease Cottons lt _ X X Cottons x X X X X Minimum iron X X X X X Woollens handcare X Denim X X X X Shirts X X X X Express X X Gentle smoothing 0 X x Steam smoothing X X Automatic plus O x x Delicates O X X Silks handcare X X Sportswear 0 X X Standard pillows E X X Outerwear 0 X X Proofing X X Warm air X X X Cool air E X X Basket programme E X Cottons hygiene X X 2 These Extras cannot be combined with one another X Can be selected O Cannot be changed Always active Cannot be selected 33 Favourite programmes You can save your own customised Selecting Extras programmes under names of your Extras choice O Gentle plus Favourite programmes once saved are listed alphabetically O Freshen
70. urther details Installation and connection Front view Mains connection cable 2 Control panel 3 Condensed water container empty after every drying cycle Door do not open during drying 8 Heat exchanger access panel do not open during drying Four height adjustable screw feet Cool air intake grille do not obstruct with a laundry basket or other objects Hose for external drainage of condensed water 69 Installation and connection Rear view N If transporting the dryer at an angle only tip towards the left side V AA 90 max Protruding lid for holding when moving the tumble dryer see arrows 2 Accessories for external drainage of condensed water hose clip adapter and hose holder 3 Hose for external drainage of condensed water Mains connection cable Transporting the dryer To manoeuvre the dryer out of its packing case to its installation site hold it by N If the tumble dryer has not been transported as described then it must be left to stand for at least 1 the front feet and the protruding lid at the back of hour before it is connected to the the appliance electricity supply Otherwise the heat pump can be A Only transport the dryer as damaged pump shown in the following illustrations 70 Installation and connection Installation A The appliance must not be
71. with a soft cloth m The drum and other stainless steel parts can be cleaned with a suitable proprietary stainless steel cleaner following the manufacturer s instructions This however is not absolutely necessary 53 Fragrance flacon Using a fragrance flacon optional accessory will add a pleasant fragrance to your laundry A Before using a fragrance flacon please read Warning and safety instructions Using a fragrance flacon optional accessory Inserting a fragrance flacon Only hold the fragrance flacon as illustrated Do not hold it at an angle m Open the cover using the tab until the or tip it as the fragrance will run out tab is at the top right hand side as of the flacon shown m Insert the flacon in the opening as far as it will go m Hold the flacon securely to prevent opening it by mistake m Pull off the protective seal m Open the door of the tumble dryer The fragrance flacon is inserted in the upper fluff filter in the opening on the right hand side beside the grip If you are not using a fragrance flacon the cover must always remain closed push the cover down completely with the tab 54 Fragrance flacon You will feel a slight resistance and Mark t li ith arkers D and 2 must line up wi arm sa chek one another Marker 2 must be in position 9 this is the position at which you can feel a resistance Before drying You can
72. y 39 Programme chart Express Max load 4 0 kg Extra dry Normal plus Normal Slightly dry Hand iron 6 Hand iron 64 Machine iron Items Garments suitable for the Cottons programme Note The programme duration is shorter Gentle smoothing Max load 1 0 kg Normal Hand irond Items Cotton and linen fabric Minimum iron items made of cotton synthetic or mixed fibre e g trousers jackets shirts Notes Suitable for dry and damp laundry Select Hand iron if the items are to be ironed after drying Smooths out creasing caused during the spin cycle in the washing machine Remove garments as soon as the programme has finished Weight of dry laundry 40 Programme chart Steam smoothing Max load 1 0 kg Normal Hand iron 6 Items Cotton and linen fabric Minimum iron items made of cotton synthetic or mixed fibre e g trousers jackets shirts Notes For all items which require dampening before ironing creasing to be removed Select Hand iron 6 if the items are to be ironed after drying Water will be taken from the condensed water container during this programme This water will then be sprayed into the drum from a jet in the door opening The condensed water container must therefore be filled with water up to at least the min marker You will be aware of more operating noise because the c
73. y dry Hand iron m Select a drying level by touching the V or sensor Any drying level can be selected for the Cottons and Express programmes A more limited range is available when using the other programmes m Confirm by touching the OK sensor 28 A Important When selecting the Steam smoothing programme you must make sure that the condensed water container has been filled as described in these operating instructions see Cleaning and care 3 Selecting a programme and starting it Other programmes and the timed drying programmes Cottons lt __ Woollens handcare Silks handcare Standard pillows Proofing Cottons hygiene The drying level is preset and cannot be altered Cool air Warm air Basket programme You can select the duration in ten minute stages Cool air 20 min 1 00 h Warm air 20 min 2 00 h Basket programme 40 min 2 30 h et programme Duration AQ h m Press the Duration button E h 0 40 2 30h m Increase Decrease the hour s by touching the V or A sensor m Confirm by touching the OK sensor m Alter the minutes in the same way Favourite programmes You can customise up to 10 programmes and save these under names of your choice These programmes can then be selected from a list See Favourites Useful tip You can also save a programme after it has started as a favourite

Operating instructions Heat pump tumble dryer

Contents

Download Pdf Manuals

Related Search

Related Contents