Operating Instructions Air Conditioner
Contents
1. Air is discharged OFF ON CD 0 TURN ON OR OFF THE UNIT TO SET TEMPERATURE Selection range 16 C 31 C MODE TO SELECT OPERATION MODE AUTO mode For your convenience Unit selects operation mode according to temperature setting outdoor and room temperature HEAT mode To enjoy warm air Unit takes a while to warm up FAN mode To enables air circulation in the room COOL mode To enjoy cool air DRY mode To dehumidify the environment Unit operates at low fan speed to give a gentle cooling operation During soft dry operation the indoor fan operates at a low fan speed The louvers movement might not align with the remote control display FAN D TO SELECT FAN SPEED 3 OPTIONS ais iiu qp ARE L For AUTO the indoor fan speed is automatically adjusted according to the operation mode If the operation mode is set to Fan the fan speed will be fixed at MED regardless of the temperature setting TO ADJ UST AIRFLOW AUTO MANUAL DIRECTION AIR SWING Keeps the room ventilated The air is discharge evenly through 4 output vents There are 3 options for auto vertical airflow direction The vertical airflow louver swings up and down automatically Do not adjust the vertical airflow direction louvers by hand MANUAL gt J gt There are 4 options for manual vertical airflow direction The airflow direction can be adjusted as desired by using re2. Lii LL F566079 Panasonic Operating Instructions Air Conditioner Indoor Unit CS F18DB4E5 CS F24DB4E5 CS F28DB4E5 Outdoor Unit Inverter Model HBE5 Series CU YL24HBE5 CU YL28HBE5 CU YL34HBE5 CU YL43HBE5 GBE5 Series CU YL24GBE5 CU YL28GBE5 CU YL34GBE5 CU YL43GBE5 Heat pump Model CU B18DBE5 CU B24DBE5 CU B28DBE5 CU B34DBE5 CS F34DB4E5 CS F43DB4E5 CS F50DB4E5 DBE5 DBE8 Series CU L24DBE5 CU L28DBE5 CU L34DBE5 CU L43DBE5 CU L50DBE8 CU B28DBE8 CU B34DBE8 CU B43DBE8 CU B50DBE8 Before operating the unit read these operating instructions thoroughly and keep them for future reference 2008 Panasonic HA Air Conditioning M Sdn Bhd 11969 T All rights reserved Unauthorized copying and distribution is a violation of law SAFETY PRECAUTION DEFINITION The instructions to be followed are classified by the following symbols This symbol denotes an action E mem These symbols denote actions that is PROHIBITED a that are COMPULSORY To prevent personal injury injury to others or property damage please observe the following Incorrect operation due to failure to follow instructions may cause harm or damage the seriousness of which is classified as below This sign warns of Warning This sign warns of death or serious injury Caution injury or damage to property Do not use rechargeable Do not install remove and Do not install the unit in a N Ni Cd batteries N rein
3. Please consult your nearest dealer for seasonal inspection Remove Air Filter Air Filter Installation 1 Press the knobs Do not use benzene thinner or scouring powder Use only soap pH7 or neutral household detergent Do not use water hotter than 40 C INDOOR UNIT Wipe the unit gently with a Insert the air filter soft dry cloth tothe tabs of the SS intake grille Slowly bring up the intake grille Zz CBA Slowly pull down the intake grille 3 Remove the air fiter from the tabs and pull it E L i downwards RIRIEILTER Press the knobs to the a CLOSE side Vacuum wash and dry Air Filter Maintenance Cleaning is needed when tis recommended to clean the air filter every 6 weeks FILTER RESET appears on After the air filter is cleaned press to Gm D the remote control display reset For wired remote control Do not operate without an air filter e Wash rinse the air filter gently with water to avoid damage to the air filter surface iun FILTER lights up on the Do not dry the part with a hair dryer or a stove Sitta indicator display Replace any damaged air filter ECONOMY Auro For wireless remote control ODOUR WASH 6 10 TROUBLESHOOTING imheifollowjingjisym ptoms do not indicate malfunction Water flowing sound during operation The room has a pecul
4. first If timer is cancelled manually you can restore the previous setting by pressing If the main power is switched off for an hour or more the clock and timer will need to be set again HINTS Set the temperature 1 C higher in cool mode or 2 C lower in heat mode than the desired temperature to achieve a 10 power saving Use curtains to screen off sunlight and outdoor heat to reduce power consumption during cool mode Will light up if Timer operation is selected 6 different programs can be set in a day 1 6 2 3 4 5 6 1 Indicate the ON TUE WED THU FRI SAT SUN selected day ON _ Time to be OFF selected Interval EE ar 10 minutes OFF Timer To automatically switch OFF the unit ON Timer To automatically switch ON the unit Day to be selected Change Display 1 Press e for 3 seconds to change the display to weekly timer Select days to run timer SELECT 2 Press to enter day setting 3 Press amp to select your desired day The selected day will be highlighted with W Press to deselect or select WW mark Repeat this step includes other day Select ON OFF Timer SELECT 4 Press to enter Timer 1 5 Press to choose ON or OFF 6 Press to confirm the selection Select Timer 7 Press to select your desired time If you want to set together with your desired UP temperature press 2 to sel
5. and repeats daily once set For clock setting l rr m please refer to Remote Control preparation There are 3 options for auto vertical airflow direction l l l l The vertical airflow louver swings up and down The timer closest to the current time will be activated automatically first Do not adjust the vertical airflow direction louvers by If timer is cancelled manually you can restore the hand previous setting by pressing SER WANUM 4 gt If the main power is switched off for an hour or more famm di 4 as 1 the clock and timer will need to be set again There are 4 options for manual vertical airflow direction The airflow direction can be adjusted as desired by _usingremote control COPTIONAESETTINGS i ECONOMY TO REDUCE POWER ECONOMY To avoid unintentional operation you can CONSUMPTION assign a different address to each indoor Recommend to use when desired room temperature is unit reached Economy operation can be activated in all modes and can be cancelled by pressing the respective button Press repeatedly to select your desired address setting Group gt Address 1 gt Address 2 gt Address 3 C ADDRESS By default ADDRESS 1 is selected You do not need to change this setting for normal operation eon im i del If the address is set to GROUP more pplicable for all models l Helps to remove unpleasant odour from t
6. even after odour wash operation is the internal parts thoroughly used continuously Turn off the power supply Remove the remote control batteries wireless remote control 11 QUICK GUIDE Start stop the operation Aik 2 oe ane Select the desired temperature TIMER RESET ADDRESS SET WIRED REMOTE CONTROL Start stop the operation EUNT Selectthe desired mode CZ RD513C sew Do T I WEROLO NC MODE UP SET SPEED MODE JP SAA de d x SELECT CANCEL AUTO MANUAL DOWN e Q9 amp d e Ww AIR SWING ECONOMY e e e e CHECK ODOURWASH VENTILATION TEST RUN FILTER RESET Selectthe desired temperature Panasonic Corporation Website http panasonic net Printed in Malaysia F566079 OSTH0806 01
7. knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance OPERATIONICONDITION T Un following temperature range Mods Temperaure Indoor Outdoor ee B BES Series HEATING em iu adm NOTICE This unit is still able to operate as a cooler with outdoor temperature as low as 15 C 10 C in a non living room such as a computer room with a room temperature of 21 C or above and room humidity up to 45 CU YL24HBE5 CU YL28HBE5 CU YL34HBE5 CU YL43HBE5 Temperature C indoor Outdoor eMe ee Minimum NOTICE This unitis still able to operate as a cooler with outdoor temperature as low as 5 C in a non living room such as a computer room with a room temperature of 21 C or above and room humidity up to 45 Thank you for purchasing Panasonic Air Conditioner SAFETY PRECAUTIONS PRODUCT OVERVIEW amp OPERATIONS WIRELESS REMOTE CONTROL 4 5 PRODUCT OVERVIEW amp OPERATIONS WIRED REMOTE CONTROL CARE amp CLEANING 9 TROUBLESHOOTING 10 11 QUICK GUIDE BACK COVER NOTE The illustrations in this manual are for explanation purposes only and may differ from the actual unit It is subjected to change without notice for future improvement Information for Users on Collection and Disposal of Old Equipment an
8. ON OR OFF THE UNIT I Sv C2 TO SET TEMPERATURE Selection range 16 C 31 C 9 e POWER e Pd TO SELECT OPERATION MODE AUTO mode For your convenience Unit selects operation mode according to temperature setting outdoor and room temperature HEAT mode To enjoy warm air Unit takes a while to warm up FAN mode To enables air circulation in the room COOL mode To enjoy cool air DRY mode To dehumidify the environment Unit operates at low fan speed to give a gentle cooling operation During soft dry operation the indoor fan operates at a low fan speed Inverter Heat pump Model The louvers movement might not align with the remote control CZ RL513B mandy kusem TO SELECT FAN SPEED 3 OPTIONS ER AUTO LOW MEDIUM HIGH 7 To turn ON or OFF the unit at a preset time For AUTO the indoor fan speed is automatically adjusted according to the operation mode Ifthe operation mode is set to Fan the fan speed will be fixed at MEDIUM regardless of the temperature setting Select ON or OFF timer m _ TO ADJUST AIRFLOW DIRECTION To cancel ON or OFF timer press eme Keeps the room ventilated The air is discharge evenly through 4 output vents When ON timer is set the unit may start early before the actual set time in order to achieve the desired temperature on time Timer operation is based on the clock set in the remote control
9. d used Batteries Information on Disposal in other Countries outside the European Union These symbols are only valid in the European Union If you wish to discard these items please contact your local authorities or dealer and ask for the correct method of disposal Note for the battery symbol bottom two symbol examples This symbol might be used in combination with a chemical symbol In this case it complies with the requirement set by the Directive for the chemical involved Do not switch ON the unit when waxing the floor After waxing aerate the room properly before operating the unit Do not install the unit in oily and smoky areas PRODUCT OVERWIEW OPERATIONS WIRELESS REMOTECONTROL Control Panel 7m POWER jo Ray receiver TIMER ww FILTER ECONOMY AUTO ODOUR WASH Auto OFF ON button To operate the unit if the wireless remote control is misplaced or malfunctioning Press once Auto Airis discharged Press and hold until you hear 1 beep Coolin evenly then release 9 z 2 1 1 Press and hold until you hear 2 beeps then release Heating Intake grille y 2 Press the ser button for 5 seconds Press the button to turn off Transmitter Maximum distances 8m Remote control Remote Control Preparation display a 1 1 Press and pull out 4 Settime 2 Insert AAA or ROS batteries 2 can be used 1 year 6 Confirm 3 Press CLOCK 6 Close the cover TO TURN
10. eck if timers have been set The unit does not receive the signal from the Make sure the receiver not obstructed remote control Make sure the address is set correctly Make sure the remote control signal transmission is within the range Certain fluorescent lights may interfere with signal transmitter Please consult your nearest dealer S pley Wired Remote Control If the CHECK indicator flashes on the wired Turn off the unit remote control Turn on again after 3 minutes If CHECK continues to blink press e for error messages If problem persist please consult your nearest authorized dealer SCHE CKD FOR SEASONAL INSPECTION AFTER EXTENDED NON SERVICEABLE CRITERIAS NON USE TURN OFF POWER SUPPLY then CALL Authorized Checking of remote control batteries wireless remote Distributor under the following conditions control Abnormal noise during operation No obstruction at air inlet and air outlet vents B DIerorel rticles h tered th te control After 15 minutes of operation it is normal to have the a a CCTHPUSMPHUR following temperature difference between air inlet and air Water leaks from Indoor unit outlet vents Circuit breaker switches off frequently Cooling 2 8 C Heating 14 C ooling ug Power cord becomes unnaturally warm FOR EXTENDED NON USE Switches or buttons are not functioning properly Activate heat mode for 2 3 hours to remove moisture leftin The odour persists
11. ect the temperature p p wy p 8 Press e to confirm the setting i CANCEL Repeat steps 5 to 8 to set Timer 2 to 6 or press to cancel the related timers OPERATION DETAILS Weekly timer i Is only appii for wired remote control press D for 3 seconds to select daily timer or weekly timer Daily timer and weekly timer could not be set at the same time Promotes energy saving by allowing you to set up to 6 timers in any given day Same timer program cannot be set on the same day Check Timer 1 Enter timer mode 2 v Se I I I SELECT r I k 2 Select the day 3 The display will show the program for each of the selected day Modify Or Add Timer Perform check timer operation to select the day Repeat steps 4 to 8 to modify existing timer program or add any new timer program Cancel Timer Perform the step below to cancel the timer program for a particular day 1 Enter timer mode 3 Press to enter day setting 4 Press to cancel the timer set Disable Weekly Timer MODE To disable weekly timer setting press then CANCEL pres Enable Weekly Timer MODE To enable previous weekly timer setting press ET then press CARE G CLEANING e Switch off the power supply before cleaning e Do not touch the aluminium fin sharp parts may cause injury CAUTION Clean the filter regularly for best performance and to reduce power consumption
12. he than one indoor unit can be operated at surrounding area during operation the same time To enable the odour removing function press the Press to restore the remote control s default once setting To cancel press the respective button again ODOUR CLEAR Not used in normal operations Applicable for Inverter model only To remove odour and minimize the growth of odour causing moulds in the air conditioner s interior section Toenable this function press the for more than 3 seconds Set the temperature 1 C higher in cool mode or 2 C The unit will automatically perform Fan and Heating lower in heat mode than the desired temperature to modes for approximately 20 minutes and then stops achieve a 10 power saving automatically Use curtains to screen off sunlight and outdoor heat to Recommended to open the windows during this reduce power consumption during cool mode operation Secale eee O ODOUR WASH e PO PRODU CTOVERMIEW OPERATIONS WIREDREMOTE CONTRO19 Air fiter Intake grille CZ RD513C TIMER CLOCK 1 OMODE UP gy SET SPEED MODE I i e e SELECT pDOWN CANCEL AUTO MANUAL DOWN a0 O ESY AIR SWING b J e e CHECK JODOUR WASH e VENTILATION TEST RUN FILTER RESET CZ RD513C For normal operation the nen and 2 buttons are not in use Remote Control Preparation Press SELECT Press to set day Confirm Repeat steps 2 and 3 to set the current time
13. iar odour Indoor fan stops occasionally during automatic fan speed setting Operation is delayed a few minutes after restart Outdoor unit emits water steam Timer indicator is always on Indoor fan stops occasionally during heating operation Cracking sound can be heard during operation Unit switch to FAN operation and air become humid Outdoor unit emits noise during heating operation Operation does not stop immediately after pressed the OFF ON button Operation stops occasionally DEFROST appears on the remote control display Airflow does not start immediately after operation is started PRE HEAT appears on the remote control display Operation starts after power resumes During dry mode cold air blow out Fan speed change occasionally during heating mode Outdoor unit emits steam during heating mode Condensation effect due to cooling process Refrigerant flow inside the unit This may due to damp smell emitted by the wall carpet furniture or clothing This helps to remove the surrounding odours The delay is a protection to the unit s compressor Condensation or evaporation occurs on pipes The timer setting repeats daily once set To avoid unintended cooling effect Changes of temperature cause the expansion contraction of the unit This happens when the room temperature reaches the set temperature operation switches to FAN mode and the humidi
14. mote control ECONOMY TO REDUCE POWER CONSUMPTION Recommend to use when desired room temperature is reached Economy operation can be activated in all modes and can be cancelled by pressing the respective button again ODOUR WASH ODOUR REMOVING Applicable for all models Helps to remove unpleasant odour from the surrounding area during operation Toenable the odour removing function press the ao once To cancel press the respective button again ODOUR CLEAR Applicable for Inverter model only To remove odour and minimize the growth of odour causing moulds in the air conditioner s interior section To enable this function press the ax 9 for more than 3 seconds The unit will automatically perform Fan and Heating modes for approximately 20 minutes and then stops automatically Recommended to open the windows during this operation TO SET DAILY TIMER To turn ON or OFF the unit at a preset time 1 2 6 MODE SELECT Enter daily timer mode Select ON or OFF timer Set the time CANCEL To cancel ON or OFF timer press When ON timer is set the unit may start early before the actual set time in order to achieve the desired temperature on time Timer operation is based on the clock set in the remote control and repeats daily once set For clock setting please refer to Remote Control preparation The timer closest to the current time will be activated
15. stall the unit by yourself SQ potentially explosive atmosphere Do not allow infants and improper installation will Do not wash the unit with water small children to play cause leakage electric benzene thinner or scouring with the remote control shock or fire Please consult powder to prevent them from an authorized dealer or Do not use for other purposes accidentally swallowing the specialist for the installation such as preservation of food batteries Work Do not use any combustible Pe emor cine bere e ithe Do not insert your fingers or equipment in front of the airflow unit is not going to be used other objects into the unit outlet for a long period of time Do not attempt to repair the Do not expose directly to cold air Bion hatencele NO mE unit by yourself for a long period type must be inserted following the polarity stated to prevent malfunction of Ensure that the drainage pipe is the remote control connected properly Otherwise leakage may occur Aerate the room regularly edil Switch off the power supply before cleaning or servicing Turn off the power supply if the unit is not used for a long period of time This air conditioner is equipped with a built in surge protective device However in order to further protect your air conditioner from being damaged by abnormally strong lightning activi
16. ty you may want to disconnect it from the power supply Do not touch the air conditioner during lightning it may cause electric shock Do not share the same power outlet with other equipment Do not modify power cords Do not use extension cords Do not operate with wet hands Use the specified supply cord If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard This equipment must be earthed and strongly recommended to be installed with Earth Leakage Circuit Breaker ELCB or Residual Current Device RCD Otherwise it may cause electrical shock or fire in case of malfunction In case of emergency or abnormal conditions burnt smell etc turn off the power supply and consult your nearest dealer Do not sit or step on the unit you SE may fall down accidentally Do not touch the sharp aluminum fin sharp parts may cause injury Ensure that the drainage pipe is connected properly Otherwise leakage may occur After long periods of use make Jut d09T VT sure the installation rack is not Do not insert your fingers or other objects damaged N into the unit sharp parts may cause injury REGULATORYANFORMATION This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and
17. ty increase This is due to changes inflow of refrigerant gas when operation stops and starts Discharging heat is in process Operation will stops automatically after approximately 60 seconds The unit is in defrosting mode and the melted frost is drained from the outdoor unit The unit is warming up to provide warm air Auto restart is in function and operates under previous setting The unit is running cooling operation with low fan speed to dehumidify the room The room temperature has reached the remote control setting When the room temperature drops again the fan speed will resume to the remote control settings This is due to defrost operation happens at the heat exchanger before iio d for servicing Check Heating Cooling operation is not working Set the temperature correctly efficiently Close all doors and windows Clean or replace the filters Clear any obstruction at the air inlet and air outlet vents Heating mode cannot be operated The unit is forced to operate at cooling mode only in a non living room such as a computer room Noisy during operation Check if the unit has been installed at an incline or the intake grille is not closed properly Remote control does not work Insert the batteries correctly Wireless remote control display is dim or Replace weak batteries transmission signal is weak The unit does not work Check if the circuit breaker is tripped Ch
Download Pdf Manuals
Related Search