Dolphin WAVE 100 Robotic Pool Cleaner Operating Instructions
Contents
1. 5 4 Maintenance Clean the filter bag with a hose Periodically clean the brushes with a hose It is recommended to periodically wash the filter bag in a washing machine Use gentle cycle program 6 Dolphin WAVE 100 Pool Cleaner Operating Instructions 8151637 _Book indb 6 29 12 2013 9 59 AM Cleaning the impeller J Unplug the power supply If you notice debris trapped in the impeller open the impeller and remove the debris Cable To remove the 1 kinks stretch ton y the cable out completely and let it sit for at least a in th Q Ta e day in the sun ee A 5 5 Off season storage If the pool cleaner will not be in use for an extended period pertorm the following storage steps e Make sure that no water is left in the pool cleaner e Thoroughly clean the filter bag and insert in place e Roll up the cable so that it has no kinks and place on the Caddy e Store the pool cleaner upright on the Caddy in a protected area out of direct sun rain frost at a temperature of between 5 45 C 41 113 F Dolphin WAVE 100 Pool Cleaner Operating Instructions 8151637 _Book indb 7 45 C 113 F 5C 41 F 29 12 2013 10 00 AM 6 POWER SUPPLY Digital Switch Mode Power Supply with full filter bag and delay indicator Input 100 250 AC Volt2. EN Dolphin WAVE 100 Robotic Pool Cleaner Operating Instructions Contents Fm As BO Oa ereere EEA erreneret newer ee re renrrreerrre ree Seren eee 2 APEE PON a EA E E E EEE octacsaetesn 2 3 WARNINGS AND CAUTIONS 2 00 cc cccccccceseeseeeseeeseesseesseenseeneeeeeenes Z Site a e Srancecete ce osetecensesd E P E E 2 CPAD E a E E E AEE eeaeincesi eeeeieeceae 2 d POQL CLEANER PART Geesin teinien E 2 Be USING THE POOL CLEEANER csutconcactisaeanttvensncaternudaeceainseranchonaenuiiesensse 4 Dd E E E E ENIE E NEE 4 5 2 Putting the Pool Cleaner into the pool s ss sssssssississississisrereen 5 5 3 Removing the Pool Cleaner from the pool c cece 5 te Manton NE eei e r e 6 55 CSS SO Oe arcsec est nc nscctsreeoseesieianeatosansessaaiotsseeeusesaansace 7 o TOWER SUPPE e E E E ee 8 AREMOTECONTROCUDIT onra a E E E 9 ADDA EMBO ccc resecscemeesereeieeasteeeeescisesdesere noesevegaceraseanseesdeeeesaasousaee 61 Dolphin WAVE 100 Pool Cleaner Operating Instructions 1 8151637 _Book indb 1 29 12 2013 9 59 AM Dolphin WAVE 100 Pool Cleaner Operating Instructions 1 INTRODUCTION Thank you for purchasing a Maytronics Robotic Pool Cleaner We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable convenient and cost effective pool cleaning Its reliable filtration in all pool conditions and all surface climbing brush enhance maximum pool hygiene The Robotic Pool Cleaners by Maytronics deliver advan
3. ced cleaning technology long lasting pertormance and easy maintenance 2 SPECIFICATIONS Motor protection IP 68 Minimum depth 0 80m 2 6ft Maximum depth 5m 16 4ft 3 WARNINGS AND CAUTIONS 3 1 Warnings Use the originally supplied power supply only Ensure the electrical outlet is protected by a ground fault interrupter GFI or an earth leakage interrupter ELI Keep the power supply out of standing water Position the power supply at least 3m 10ft away from the edge of the pool Do not enter the pool while the pool cleaner is working Unplug the power supply before servicing 3 2 Cautions When not in use store the Pool Cleaner on the Caddy in a shaded area Use the Pool Cleaner in the following water conditions only Te 8151637 _Book indb 2 Dolphin WAVE 100 Pool Cleaner Operating Instructions 29 12 2013 9 59 AM 4 POOL CLEANER PARTS Dolphin WAVE 100 Combined Brush All surface climbing brush ideal for most pool surfaces Wonder Brush For smooth ceramics optional Bottom lid and filter Bag Filter bag options Fine factory default Power Supply Ultra fine extra Unit Disposable filter bag x 5 Dolphin WAVE 100 Pool Cleaner Operating Instructions 3 8151637 _Book indb 3 29 12 2013 9 59 AM 5 USING THE POOL CLEANER 5 1 Set Up Before using the Pool Cleaner for the first time perform the following steps Unwind the cable and stretch it out compl
4. etely so that it has no kinks GFI ELI Attach the floating cable to the power supply by inserting it with the notch on the connector 1 lined up with the groove in the socket on the power supply and turning clockwise 2 RY ac Change diagonal handle position 1 2 Normal advance for water line sideway movement More efficient cleaning To adjust the handle angle action on water line A Press the latch down and hold it in position B Move the handle to the desired 3 4 Fast advance position and release the latch to hold the handle in place Fast speed for faster but less efficient cleaning action on water line 4 Dolphin WAVE 100 Pool Cleaner Operating Instructions 8151637 _Book indb 4 29 12 2013 9 59 AM 5 2 Putting the Pool Cleaner into the pool If the foam climbing rings on the brushes are dry soak them in water until soft Shake the robot from side to side or turn it upside down to release trapped air Let it sink to the pool floor Turn the power supply ON 5 3 Removing the Pool Cleaner from the pool The robot will perform automatic shut off at the end of the cleaning cycle J Turn OFF and unplug the power supply Dolphin WAVE 100 Pool Cleaner Operating Instructions 5 8151637_Book indb 5 29 12 2013 9 59 AM Using the floating cable bring the Pool Cleaner to the pool s edge ZN DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE
5. ol cleaner Fast 4 hour cycle Immediate start Default setting Standard Floor and wall cleaning Default setting Efficient Extra 6 hour cycle for 8 hour cycle everyday use Default setting One hour delay Two hour delay Ultra clean Floor only Stronger suction Cleans only the Cleans walls and and slower floor and the area waterline only movement where the floor and floor and wall walls meet will continue to work in the previous settings e When the Ultra Clean and Walls Only options finish their cycles the Pool Cleaner will return to default settings 10 8151637 _Book indb 10 Dolphin WAVE 100 Pool Cleaner Operating Instructions 29 12 2013 10 00 AM
6. on Manual automatic select button Set OK button Direction control arrows Manual Direction Control Mode 1 Press the On Off button once The remote control will start in manual direction control mode On Off button 2 Use the direction control arrows see right to control the ical movement of the robot around the pool arrows 1 To exit the manual direction control mode press the Manual Manual Automatic select button once only Automatic ae 2 The digital screen will light up and three rows of function utton icons will be displayed in default mode 1 To change the parameters press the up or down arrows 2 To select the parameter settings use the right or left arrows Set OK control When you reach the required function press the Set OK f button Direction arrows button Dolphin WAVE 100 Pool Cleaner Operating Instructions Q 8151637_Book indb 9 29 12 2013 10 00 AM Press the Manual Automatic select button and then choose the desired parameters according to the following table Cleaning cycle indicator This determines the length of the cleaning cycle Delay time indicator This determines when the pool cleaner starts to work Delaying allows the dirt to settle to the bottom of the pool Cleaning action indicator Allowing you to choose from the following options Note e After 2 minute if no button is pressed the Remote Control Unit will shut down and the Po
7. s 50 60 Hertz 180 Watt Output lt 30 VDC IP 54 Delay indicator Full filter bag indicator lt 30 VDC IP 54 On Off switch Reset button On Full filter bag indicator and Reset button The power supply is equipped with a filter bag status indicator The red LED indicates two filter conditions e When blinking The filter is partially blocked e When lighted The filter is blocked and must be emptied and cleaned If the LED does not turn off after the filter bag had been emptied and cleaned press the RESET button while the robot is working Delay indicator The power supply is equipped with a Delay indicator that indicates if the Delay option is activated through the remote control unit 8 Dolphin WAVE 100 Pool Cleaner Operating Instructions 8151637_Book indb 8 29 12 2013 10 00 AM 7 REMOTE CONTROL UNIT The Control Panel Radio reception meter When no black lines are showing move closer to the power supply unit Battery level meter When flashing change the batteries The remote control unit RCU ch meine offers two operation modes Automatic mode and manual direction control mode Manual control indicator When flashing you are in manual direction control mode Cleaning cycle icons In automatic mode the cleaning parameters can be changed Delay timer icons Cleaning mode icons In manual direction mode the robot s motion can be controlled manually ON OFF butt
Download Pdf Manuals
Related Search