Operating Instructions
Contents
1. To avoid unintended cooling effect operation POWER indicator blinks before the unit is This is a preliminary step in preparation for the Switched on operation when the ON timer has been set Cracking sound during operation Changes of temperature caused the expansion contraction of the unit POWER indicator blinks 3 seconds ON and The unit is in Demand Response Mode 0 5 seconds OFF during operation Check the following before calling for servicing I Symptom Check Operation in HEAT COOL mode is not working Set the temperature correctly efficiently Close all doors and windows Clean or replace the filters Clear any obstruction at the air inlet and air outlet vents Noisy during operation Check if the unit has been installed at an incline Close the front panel properly Remote control does not work Insert the batteries correctly Display is dim or transmission signal is weak Replace weak batteries The unit does not work Check if the circuit breaker is tripped Check if timers have been set The unit does not receive the signal from the Make sure the receiver is not obstructed remote control Certain fluorescent lights may interfere with signal transmitter Please consult authorised dealer NON SERVICEABLE CRITERIAS The unit stops and the TIMER indicator blinks TURN OFF POWER SUPPLY AND Use remote control to retrieve error code UN2. PLUG then please consult authorised Press for dealer under the following conditions 5 seconds Abnormal noise during operation Press until you hear beep sound then write down Water foreign particles have entered the 8 Press for the error code remote control 5 seconds Tex aoc 4 Turn the unit off Water leaks from Indoor unit to quit and reveal the Circuit breaker switches off frequently checking error code to Power cord becomes unnaturally warm authorised dealer Switches or buttons ale nar Tunepeninig For certain errors you may restart the unit for limited properly operation with 4 beeps when operation starts 10 F569362 YAO413 0 EN indd 10 e 6 14 2013 10 09 53 AM Information Information for Users on Collection and Disposal of Old Equipment and used Batteries Information on Disposal in other Note for the battery symbol bottom Countries outside the European two symbol examples Union This symbol might be used in wag hese symbols are only valid in the combination with a chemical symbol these items please contact your local requirement set by the Directive for the authorities or dealer and ask for the chemical involved European Union If you wish to discard T In this case it complies with the correct method of disposal Pb Troubleshooting Information English 11 F569362_YA0413 0_EN indd 11 e 6 14 2013 10 09 54 AM Panasonic Corporati
3. Panasonic Operating Instructions Air Conditioner uu Model No Indoor Unit Outdoor Unit CS RE18PKR CU RE18PKR CS RE24PKR CU RE24PKR CS RE28PKR CU RE28PKR Ja LL Operating Instructions Air Conditioner Thank you for purchasing Panasonic Air conditioner Installation instructions attached Before operating the unit read these operating instructions thoroughly and keep them for future reference English F569362 F569362_YA0413 0_EN indd 1 e 6 14 2013 10 09 45 AM Quick guide Inserting the batteries D Pull out the back cover of remote control 2 Insert AAA or R03 batteries can be used 1 year Close the cover Clock setting D Press CLOCK Set the time Confirm Basic operation Select the desired mode ero HEAT COOL FAN DRY Mai 2 Start stop the operation _ 262 POWER Please note that the OFF indication OFF is on to start Select the desired temperature Selection range 16 C 30 C Not applicable for FAN mode Operating the unit within the recommended temperature may save energy HEAT 20 C 24 C COOL 26 C 28 C DRY 1 C 2 C lower than room temperature The set temperature selection range can be customized according to requirement Please consult authorised dealer To dim or restore the unit s indicator brightness press and hold for 5 seconds Use remote control within 8 m from the remote contr
4. eaks from the indoor unit Power cord or plug becomes abnormally hot Fan speed cannot be controlled The unit stops running immediately even if it is switched on for operation The fan does not stop even if the operation is stopped Contact your local dealer immediately for maintenance repair This equipment must be earthed to prevent electrical shock or fire oS Prevent electric shock by switching off the power supply and unplug Before cleaning or servicing When extended non use or During abnormally strong lightning activity N CAUTION Indoor unit and outdoor unit 9S Do not wash the indoor unit with water benzine thinner or scouring powder to avoid damage or corrosion at the unit F569362_YA0413 0_EN indd 5 Do not use for preservation of precise equipment food animals plants artwork or other objects This may cause quality deterioration etc Do not use any combustible equipment in front of the airflow outlet to avoid fire propagation Do not expose plants or pet directly to airflow Do not touch the sharp aluminium fin sharp parts may cause injury to avoid injury etc Do not switch ON the indoor unit when waxing the floor After waxing aerate the room properly before operating the unit Do not install the unit in oily and smoky areas to prevent damage to the unit Do not dismantle the unit for cleaning purpose to avoid inju
5. ically after 20 minutes QUIET To enjoy quiet operation zezQUIET ECONOMY This operation reduces airflow noises Remote control display AIR CONDITIONER R FF ON LO og ERR Remote control receiver and indicator POWER Green TIMER Orange QUIET ECONOMY Orange POWERFUL Orange Press and hold for approximately 10 seconds to show temperature setting in TEMP C or F poem S AIR SWING gui pasan Cap Press to restore the remote control to S default setting 1 OFF Not used in normal panasonic operations CONVERTER ANS To select fan speed Remote control display AUTO gt gt ati sil stil anii For AUTO the indoor fan speed is automatically adjusted according to the operation mode Auto OFF ON button Use when remote control is misplaced or a malfunction occurs Raise the front panel To use in AUTO mode press the button once To use in COOL mode press and hold the button until 1 beep is heard then release To use in HEAT mode press and hold the button until 1 beep is heard then release And press again until 2 beeps then release Press the button again to turn off F569362 YAO413 0 EN indd 6 e 6 14 2013 10 09 47 AM See To learn more for details To set the timer To save electrical power Econo consumption 2 sets of ON and OFF time
6. mbol denotes an action that is PROHIBITED These symbols denote actions COMPULSORY Qoo Power supply Air inlet Indoor unit F569362 YAO413 0 EN indd 4 N WARNING Indoor unit and outdoor unit Q This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Please consult authorised dealer or specialist to clean the internal parts repair install remove and reinstall the unit Improper installation and handling will cause leakage electric shock or fire Confirm with authorised dealer or specialist on usage of any specified refrigerant type Using refrigerant type other than the specified result in fire injury long period to avoid excess cooling Remote control 9 may cause product damage burst and injury etc Do not install the unit in a potentially explosive or flammable atmosphere Failure to do so could Do not insert your fingers or other objects into the air conditioner indoor or outdoor unit rotating parts may cause Do not touch the outdoor unit during lightning it may cause electric shock Do not expo
7. ol receiver of the indoor unit The illustrations in this manual are for explanation purposes only and may differ from the actual unit They are subject to change without notice for future improvement F569362 YAO413 0 EN indd 2 e 6 14 2013 10 09 46 AM RC CHECK QOCK nest Panasonic CNVERTER Table of contents Safety precautions OFF COOL J pu v LINE i oO Ls a toring Ae 1C UIL FAN TEMP Powerru 1 QUIET TIMER ON 1 OFF ac Panasonic INVERTER SSS Af 8m A How to S ei naia ada 6 7 To l ar more mte 8 Cleaning instructions ssssssse 9 Troubleshooting 10 Information eret 11 Accessories Remote control AAA or R03 batteries x 2 Remote control holder Screws for remote control holder x 2 F569362 YAO413 0 EN indd 3 6 14 2013 10 09 46 AM English Safety precautions To prevent personal injury injury to others or property damage please comply with the following Incorrect operation due to failure to follow instructions below may cause harm or damage the seriousness of which is classified as below This sign warns of death or serious injury AN WARNING This sign warns of CAUTION injury or damage to gt property The instructions to be followed are classified by the following symbols This sy
8. on Website http panasonic net Panasonic Corporation 2013 F569362 YA0413 0 Printed in Malaysia F569362_YA0413 0_EN indd 12 e 6 14 2013 10 09 54 AM
9. p parts may cause injury Do not use benzine thinner or scouring powder Use only soap pH 7 or neutral household Air filters detergent Do not use water hotter than 40 C Air filters Every 2 weeks Anti bacterial filter Indoor unit Wash rinse the filters gently E Wipe the unit gently with a soft with water to avoid damage to 9 dry cloth the filter surface o Dry the filters thoroughly under shade away E from fire or direct sunlight I Replace any damaged filters o Front panel Remove air filter Attach air filter T Wash gently and dry 5 Remove the front panel g 2 Pull out 2 E c Insert into the unit D Raise Anti bacterial filter n eZ Anti bacterial filter 5 Ot 2 Ww Close it securel Clean the filter whenever necessary SPESE e Washrrinse the filter gently with water to avoid D Insert at damage to the filter Press both ends of both sides Dry the filter thoroughly under the shade away the front panel from fire or direct sunlight Replace the filter every 10 years or replace any damaged filter Part no CZ SA22P For seasonal inspection after extended non use Checking of remote control batteries No obstruction at air inlet and air outlet vents Use Auto OFF ON button to select COOL HEAT operation After 15 minutes of operation it is normal to have the following temperature difference between air Cl d inle
10. rs are available to turn ON or OFF the unit at different preset zezQUIET ECONOMY times Save power consumption at unoccupied room by adjust set temperature up to 3 C automatically Brightness of all indicators will be dimmed aswe To adjust airflow direction Ve D Select ON or OFF Example timer OFF at 22 00 Remote control display Eachtime pressed ma g PUT RE E E 61 O2 P Cancel n LEEREN 7 ET e AUD m e e ERN 2 Set the time ve or a 2 DIA CEU w Keeps the room ventilated In COOL DRY mode if AUTO is set the louver 8 Confirm BB aan D i swings left right and up down automatically In HEAT mode if AUTO is set the horizontal louver is fixed at the predetermined position 2e TIMER The vertical louver swings left right after the mm temperature rises To cancel ON or OFF timer press E or ja Do not adjust the louver by hand to select respective 1 or 2 then press Gig If timer is cancelled manually or due to power failure you can restore the timer again by pressing 68 or ger to select respective 1 or then press SE The nearest timer setting will be displayed and will activate in sequence When ON Timer is set the unit may start earlier up to 35 minutes before the actual set time in order to achieve the desired temperature on time Timer operation is based on the clock set in the remote control and repeats daily once set For clock setting please refer to Quick g
11. ry Do not step onto an unstable bench when cleaning the unit to avoid injury Do not place a vase or water container on the unit Water may enter the unit and degrade the insulation This may cause an electric shock Do not open window or door for long time during COOL DRY mode operation Q Prevent water leakage by ensuring drainage pipe is Connected properly Kept clear of gutters and containers or Not immersed in water After a long period of use or use with any combustible equipment aerate the room regularly After a long period of use make sure the installation rack does not deteriorate to prevent the unit from falling down Remote control 9 Do not use rechargeable Ni Cd batteries It may damage the remote control o Power supply S To prevent malfunction or damage of the remote control Remove the batteries if the unit is not going to be used for a long period of time New batteries of the same type must be inserted following the polarity stated Do not disconnect the plug by pulling the cord to prevent electric shock 6 14 2013 10 09 47 AM Safety precautions English How to use wobE To select operation mode AUTO For your convenience HEAT To enjoy warm air COOL To enjoy cool air DRY To dehumidify the environment FAN To circulate air in the room Pout To reach temperature quickly 2 POWERFUL This operation will stop automat
12. se yourself directly to cold air for a Do not sit or step on the unit you may fall down accidentally Do not allow infants and small children to play with the remote control to prevent them from accidentally swallowing the batteries Power supply Do not use a modified cord joint cord extension cord or unspecified cord to prevent overheating and fire 6 14 2013 10 09 47 AM To prevent overheating fire or electric shock Do not share the same power outlet with other equipment Do not operate with wet hands Do not over bend the power supply cord Do not operate or stop the unit by inserting or pulling out the power plug If the supply cord is damaged it must be replaced by the manufacturer service agent or similarly qualified persons in order to avoid a hazard It is strongly recommended to be installed with Earth Leakage Circuit Breaker ELCB or Residual Current Device RCD to prevent electric shock or fire To prevent overheating fire or electric shock Insert the power plug properly Dust on the power plug should be periodically wiped with a dry cloth Stop using the product if any abnormality failure occurs and disconnect the power plug or turn off the power switch and breaker Risk of smoke fire electric shock Examples of abnormality failure The ELCB trips frequently Burning smell is observed Abnormal noise or vibration of the unit is observed Water l
13. t and air outlet vents ose JOWN COOL 28 C HEAT 2 14 C a Press at center of the front panel For extended non use Activate HEAT mode for 2 3 hours to remove moisture left in the internal parts thoroughly to prevent mould growth Turn off the power supply and unplug Remove the remote control batteries 9 F569362_YA0413 0_EN indd 9 e 6 14 2013 10 09 49 AM Troubleshooting The following symptoms do not indicate malfunction Symptom Cause Mist emerges from indoor unit Condensation effect due to cooling process Water flowing sound during operation Refrigerant flow inside the unit The room has a peculiar odour This may be due to damp smell emitted by the wall carpet furniture or clothing Indoor fan stops occasionally during automatic This helps to remove the surrounding odour fan speed setting Airflow continues even after operation has Extraction of remaining heat from the indoor unit stopped maximum 30 seconds Operation is delayed a few minutes after The delay is a protection to the unit s compressor restarting Outdoor unit emits water steam Condensation or evaporation occurs on pipes TIMER indicator is always on The timer setting repeats daily once set POWER indicator blinks during HEAT mode The unit is in defrost mode and AIR SWING is set to with no warm air supply and louver is closed AUTO Indoor fan stops occasionally during heating
14. uide How to use English Notes Can be activated in all modes and can be cancelled by pressing the respective button again Cannot be selected at the same time F569362 YAO413 0 EN indd 7 e 6 14 2013 10 09 48 AM To learn more AUTO During operation mode selection the POWER indicator blinks Unit selects operation mode during startup according to setting temperature and room temperature HEAT Unit takes a while to warm up The POWER indicator blinks during this operation COOL Use curtains to screen off sunlight and outdoor heat to reduce power consumption during COOL mode DRY Unit operates at low fan speed to give a gentle cooling operation FAN Tocirculate air in the room Operation conditions Use this air conditioner under the following temperature range DBT Dry bulb temperature WBT Wet bulb temperature Temperature C Indoor Outdoor u P DBT WBT DBT WBT Max 32 23 46 26 COOL Min 16 11 5 4 Max 30 24 18 HEAT Min 16 15 16 F569362 YAO413 0 EN indd 8 D 6 14 2013 10 09 49 AM e Cleaning instructions To ensure optimal performance of the unit Indoor unit cleaning has to be carried out at regular Front panel intervals Dirty unit may cause malfunction and you may see error code H99 Please consult authorised dealer Switch off the power supply and unplug before cleaning Do not touch the aluminium fin shar
Download Pdf Manuals
Related Search