Operating Instructions - Xf50
Contents
1. No milk flow Milk spluttering Not filling cups Milk not hot enough Froth milk is flat amp cool Note If there is no steam or the steam pressure is low follow the steam trouble shooting procedure first Solution 1 Remove the air suction Fig 1 2 Check the valve on the tip of the air suction is clean and is able to open and close freely Squeeze the valve between your figures it should open release it and it should close Fig 2 3 Refit the air suction Turn the milk selector to the froth position Fig 3 and test the milk If the milk is still cool and flat replace the air suction and test again If the problem has been resolved order in a spare air suction part no 71210 otherwise go to step 4 Remove the auto frother from the machine Fig 4 Separate the auto frother into 4 parts Fig 5 Soak the parts in 250ml of warm water and 15ml of Jura cappuccino cleaner for 15 20 min Remove the parts from the solution and rinse them under tap water Clean the milk and air paths with the cleaning brush part no 71161 Fig 6 9 Re assemble the auto frother and refit onto the machine 0 Test the milk function If the problem has not been resolved contact customer support on 1300 365 487 to arrange the repair of your machine a Se et oP ah SS Figure 1 Figure 2 Figure 3 Froth Figure 4 Figure 5 Figure 6 Milk Figure 7 Milk Figure 8 Air Figure 9 Milk f 9 Hall Street 93 1 5 Har2. e pressure is low descale the machine and test the steam pressure again Note If you normally use Claris filters descale with 1 tablet only See manual Descaling machine b If there is still no steam or steam is escaping from the wrong location please contact customer support on 1300 365 487 to arrange the repair of your machine Figure 4 Figure 5 Figure 7 N j 2 f f 9 Hall Street 93 1 5 Harwood Street L o ree 5 Or Hawthorn East Vic 3123 Pyrmont NSW 20009 g 2 ph 03 9946 4160 ph 02 9034 6580 My Coffee Shop Pty Ltd fax 03 9822 6269 fax 02 9034 6586 ACN 102 850 037 servicecentre mycoffeeshop com au 1300 365 487 www mycoffeeshop com au
3. eshop com au IMPRESSA XF50 Classic Precondition KESE Cleaning the machine Approximate duration 15 min Equipment required 2 phase cleaning tablets Tub of 25 Art 62535 Pack of 6 Art 62715 4 A These short instructions do not replace the IMPRESSA XF50 Instructions for Use Make sure you read and observe the safety information and warnings first in order to avoid hazards JURA Elektroapparate AG KaffeeweltstrafSe 10 CH 4626 Niederbuchsiten www jura com IMPRESSA XF50 Classic Precondition 2 Descaling the machine 2 Approximate duration 40 min 2 Equipment required Descaling tablets Tub of 36 Art 70751 Pack of 3 Art 61848 3 4 A These short instructions do not replace the IMPRESSA XF50 Instructions for Use Make sure you read and observe the safety information and warnings first in order to avoid hazards JURA Elektroapparate AG Kaffeeweltstrafge 10 CH 4626 Niederbuchsiten www jura com IMPRESSA XF50 Classic fra Changing the filter en Say Equipment required CLARIS Pro Blue filter cartridge Pack of 4 Art 69670 A These short instructions do not replace the IMPRESSA XF50 Instructions for Use Make sure you read and observe the safety information and warnings first in order to avoid hazards JURA Elektroapparate AG Kaffeeweltstrafse 10 CH 4626 Niederbuchsiten www jura com Trouble shooting Milk not frothing
4. fra Jura Impressa XF50 Operating amp cleaning Instructions M rf 9 Hall St Shop 93 1 5 Harwood Street L o a ox oo Sho Hawthorn East VIC 3123 Pyrmont NSW 2009 5 2 ph 03 9946 4160 ph 02 9034 6580 fax 03 9822 6269 fax 02 9034 6586 My Coffee Shop Pty Ltd ACN 102 850 037 clientservices mycoffeeshop com au 1300 365 487 www mycoffeeshop com au Rotary Switch Control elements l Illuminated ring o o N DW auon A W N Rotary Switch Maintenance button Preparation button 1 espresso Preparation button 2 espressi Preparation button 1 coffee Preparation button 2 coffees Steam preselection button Display dialogue system Water tank with handle Filler funnel for preground coffee Bean container cover Aroma preservation cover Steam hot water draw off tap Removable Professional Cappuccino Frother with milk pipe Removable hot water nozzle see Fig 5 Height adjustable coffee spout Coffee grounds container Cup grille Drip tray On Off button Zero Energy Switch Metal shelf Operating Instructions Jura XF50 fine foam fia Cappuccino 1 Place your cup mug under the milk coffee spout on the right 2 Turn the milk selector to the foam milk position See diagram below 3 Press the cappuccino key Your cappuccino will now be poured Flat white 1 Place your cup mug under the spout on the right 2 Turn the milk selec
5. leaning solution through the milk frother in the froth milk position and half in the flat milk position 5 Rinse the cleaning container jug and fill it with 250 ml of cold water Repeat step 4 to rinse the auto frother My offee Shop My Coffee Shop Pty Ltd ACN 102 850 037 C lientservices mycoffeeshop com a u Warehouse 4 41 Rose Street Richmond Vic 3121 ph 03 9946 4160 fax 03 9429 0055 Level 26 44 Market Street Sydney NSW 2000 ph 02 9034 6580 fax 02 9034 6586 1300 365 487 www mycoffeeshop com au Weekly cleaning proceedure Milk system Complete this procedure once a week after the daily milk system clean Remove the automatic milk frother from the machine Fig 1 2 2 Separate the automatic milk frother into 4 parts Fig 3 3 Soak the parts in 250ml of warm water not hot and 15ml of Jura cappuccino cleaner for 15 20 min max 4 Remove the parts from the solution and rinse them under cold tap water 5 Re assemble the auto frother and refit onto the machine Figure 1 Figure 2 Figure 3 N A f f 9 Hall Street 93 1 5 Harwood Street L G T 55 Hawthorn East Vic 3123 Pyrmont NSW 20009 O AEBS we 2 ph 03 9946 4160 ph 02 9034 6580 My Coffee Shop Pty Ltd fax 03 9822 6269 fax 02 9034 6586 ACN 102 850 037 servicecentre mycoffeeshop com au 1300 365 487 www mycoffe
6. tor to the flat milk position See diagram below 3 Press the Latte macchiato key Your flat white will now be poured Cafe Latte 1 Follow the procedure for making a cappuccino 2 When your cup or glass 1 3 full of foam milk turn the milk selector to the flat milk position Espresso or Long Black 1 Place your cup mug under the middle spouts and press espresso or coffee key Your drink will now be poured Press the button twice for a double espresso or two long blacks Note Each key is fully programmed however you can stop the milk and coffee flow short by pressing any key while it is pouring Adjustments to suit personal preference can also be made using the rotary dial These changes do not affect the programmed settings 9 Hall St Shop 93 1 5 Harwood Street Mc offee Sho Hawthorn East VIC 3123 Pyrmont NSW 2009 g D ph 03 9946 4160 ph 02 9034 6580 fax 03 9822 6269 fax 02 9034 6586 My Coffee Shop om Ltd l ACN 10 2 850 037 oo i oo l clientservices m coffeesho com au 1300 365 487 www mycoffeeshop com au Jura Impressa Xf50 End of Day cleaning 1 Fill a cleaning jug with 250 ml of cold water and add 15ml of cappuccino cleaning solution 2 Lift the milk pipe up out of the cooler and place it into the cleaning jug Place the second cleaning jug under the steam outlet 3 Select steam The machine will heat for 20 sec and then display ready 4 Open the steam tap Draw half of the c
7. wood Street ee 5 Tofa Hawthorn East Vic 3123 Pyrmont NSW 20009 2 ph 03 9946 4160 ph 02 9034 6580 My Coffee Shop Pty Ltd fax 03 9822 6269 fax 02 9034 6586 I IW servicecentre mycoffeeshop com au 1300 365 487 www mycoffeeshop com au Trouble shooting Steam No steam Low steam Steam coming from the wrong location Solution 1 oo S ON Figure 6 Unplug the machine for 10 seconds plug the machine back in turn it on and test the milk function If the problem has not been resolved go to step 2 Remove the auto frother from the machine Fig 1 Pull the chrome steam nozzle cap toward you until it un clips from the steam nozzle below it Fig 2 Unscrew the steam nozzle from the steam arm turning it clockwise as you look down onto it Fig 3 Clean the 1mm diameter steam hole in the steam nozzle using the cleaning brush part no 71161 Fig 4 5 screw the steam nozzle back onto the steam arm turning it anti clockwise as you look down onto it Using a tea towel grip the steam nozzle and tighten so that it is hand tight Re fit the chrome steam nozzle cap by placing it into position supporting the steam nozzle below it with one hand and with the other hand pushing the steam nozzle cap down as you rock it forwards and backwards It will clip onto the steam nozzle Fig 6 Re fit the auto frother Fig 7 Test the steam using the milk function a If there is steam coming from the steam nozzle however th
Download Pdf Manuals
Related Search